Search

Numerous metrics and indices have been proposed for the assessment of thermal perception and comfort. Commonly used indices based on the estimate of the heat flow between the human and its environment includes the well-known Fanger's method, also known as the PMV-PPD thermal comfort model. Recently this thermodynamic approach has been expanded with the application of the second law of thermodynamics. In this paper, an exergy-based analysis of the relation between the human and its environment is presented. Heat and mass flow rate due to convection, radiation, evaporation and respiration are calculated and expressed in terms of exergy loss. This value is used in the modified Fanger's thermal comfort model, where the heat balance equation is replaced by the exergy loss. The paper builds upon prior studies on determination of internal and external exergy losses by revised and newly defined formulas taking into account clothing and indoor conditions. The results quantitatively show that thermal energy load in the original Fanger's PMV model could be substituted by exergy loss and it corresponds to a certain level of subjective assessed thermal comfort level. [ABSTRACT FROM AUTHOR]

Grate boilers are widely applied in biomass combustion for heat and energy generation. However, grate-firing systems often suffer from low efficiency and high emission. Computational fluid dynamic (CFD) becomes increasingly popular as a flexible method to obtain the detailed combustion behaviors in the furnace, and to optimize the performance of existing grate boilers. This paper presents efforts toward a reliable baseline CFD model for an industrial biomass-fired grate boiler, where the structure of the fuel-bed was sufficiently considered. The combustion performances in the furnace were investigated experimentally and numerically by coupling the fuel bed and freeboard, to clarify the impact of bed structure on the simulation accuracy. Results show that when the bed structure has been taken into account, the predictions are in better agreement with the various measurements, as the deviations between them are all within 10 %. Moreover, the flame center drops, the total heat transferred to the water-cooled walls increases, and the residence time of flue gas is greatly prolonged from 2.76 s to 3.90 s, resulting in a distinct difference of the temperature and species patterns in the freeboard. The simulations will provide valuable theoretical guidance for the accurate modeling of grate-fired boiler. [Display omitted] • A baseline model is proposed for accurate modeling of biomass-fired grate boiler. • Effect of fuel-bed structure on the simulation of grate boiler is clarified in detail. • Bed structure greatly affects the predicted temperature and species patterns. • Flue gas residence time and heat transfer are also highly impacted by bed structure. [ABSTRACT FROM AUTHOR]

Abstract The subject of this paper is the steam boiler nonlinear mathematical model. The furnace chamber heat transfer is modelled assuming that the flue gas temperature across the entire furnace chamber is constant. Only radiation heat transfer to the boiler waterwalls is modelled. Distributed parameter mathematical models are developed of the steam superheater individual stages: the superheater first stage, the platen superheater, the second and third stage of the superheater. In the same way, the boiler two-stage economizer is modelled. The flue gas and air temperatures downstream the air heater individual stages are determined using the ε-NTU method (effectiveness ε - the number of transfer units NTU). Due to such arrangement of the boiler heating surfaces and the heat transfer nonlinear character, iterative calculations of the steam, flue gas, and air temperatures are necessary. The developed mathematical model makes it also possible to determine temperatures of the tube outer and inner surfaces and external fouling for all heating surfaces of the boiler. The developed non-linear mathematical model of the entire boiler has high practical importance. The proposed mathematical model can be used to simulate the boiler operation in various conditions, allowing to determine and correct selection the parameters of boiler operation. A non-linear mathematical model of the boiler can also be used to design the individual stages of the superheater properly so as to achieve the desired temperature behind the individual stages. Determination of the local temperature of the tube wall allows selecting an appropriate grade of steel for the individual stages of the superheater. Also, the developed non-linear mathematical model can be used for boiler operation monitoring in on-line mode. Highlights • A nonlinear mathematical model of the entire steam boiler was presented. • Mathematical models of individual heating surfaces in the boiler were presented. • Results of the boiler operation simulations were presented. • Results of the boiler economizer operation were presented. [ABSTRACT FROM AUTHOR]

The project reported in this paper used CFD as a tool to investigate the effect of multi-pass on the shell side heat transfer of a heat exchanger system. The heat exchanger system is equipped with six vertical thermosyphons transferring thermal energy from a heat source (air) to a heat sink (water). The CFD model has been experimentally validated. The two-phase change processes inside the thermosyphons were not modelled during the simulation. Instead, the thermosyphons were treated as solid rods with a constant thermal conductivity, which was calculated theoretically by applying the thermal resistance analogy with the aid of convection, boiling and condensation correlations found in the literature. The heat source consists of multiple air passes on the evaporator section of the thermosyphons and two water passes on the condenser section. Three different arrangements on the evaporator section were investigated with one, two or three shell passes and the thermal performance compared for the three configurations. The investigation was performed at various inlet conditions: a range of air inlet temperatures (100, 150, 200 and 250 °C) and mass flow rates (0.05, 0.08, 0.11 and 0.14 kg/s). The water inlet conditions were kept constant (a temperature of 15 °C and a mass flow rate of 0.08 kg/s). The overall rate of heat transfer was obtained by both CFD and a theoretical model, and the results lay within 15% of the experimental data. The numerical predictions demonstrated that the k − ε Realizable turbulence model is a reliable tool for predicting heat transfer and fluid flow in such heat exchangers. [ABSTRACT FROM AUTHOR]

The Enhanced Geothermal System (EGS) creates an artificial geothermal reservoir by hydraulic fracturing which allows heat transmission through the fractures by the circulating fluids as they extract heat from Hot Dry Rock (HDR). The technique involves complex thermal–hydraulic–mechanical (THM) coupling process. A numerical approach is presented in this paper to simulate and analyze the heat extraction process in EGS. The reservoir is regarded as fractured porous media consisting of rock matrix blocks and discrete fracture networks. Based on thermal non-equilibrium theory, the mathematical model of THM coupling process in fractured rock mass is used. The proposed model is validated by comparing it with several analytical solutions. An EGS case from Cooper Basin, Australia is simulated with 2D stochastically generated fracture model to study the characteristics of fluid flow, heat transfer and mechanical response in geothermal reservoir. The main parameters controlling the outlet temperature of EGS are also studied by sensitivity analysis. The results shows the significance of taking into account the THM coupling effects when investigating the efficiency and performance of EGS. [ABSTRACT FROM AUTHOR]

This paper addresses the optimal arrangement and design of a dual pressure heat recovery steam generator coupled to two steam turbines. A superstructure that embeds various alternative configurations is optimized considering the following two single objective functions: (a) the maximization of the total net power generation for a given total heat transfer area and (b) the minimization of the total heat transfer area for a given total net power. The optimal number of heat exchangers and pumps and how they should be connected are the discrete decisions. The dimensions and operating conditions are the continuous decisions. A discrete and continuous mathematical model is developed and logical propositions are used for discrete decisions. The results are compared with a reference case reported by other authors. The results indicated that the optimization of the proposed superstructure allowed to find a more efficient HRSG configuration. The obtained configurations differ from the configuration of the reference case in how the heat exchangers and pumps are connected. A considerable increase in about 8% of the total net power generation in (a) and a significant reduction in about 24% of the total heat transfer area in (b) are achieved when compared to the reference case. [ABSTRACT FROM AUTHOR]