Search

[Display omitted] • Localized heating systems are a proper solution for providing thermal comfort. • Providing personalized heating by radiation or conduction is more convenient, so the inhaled air is kept cool and pleasant. • Local radiant heating systems directly heat the body without heating the environment, leading to lower energy consumption. • With local radiant heating systems, proper thermal comfort and sensation can be achieved even at low air temperatures. Localized heating systems are a proper solution for providing thermal comfort while lowering energy consumption in cold environments. Local radiant heating systems provide thermal comfort at lower air temperatures than convective systems which heats air, resulting in cool and pleasant inhalation air. This paper reviews experimental studies regarding local radiant heating systems considering thermal sensation and comfort. These systems can heat body directly, often with a big view factor toward the body. They do not necessarily heat the air and environment, leading to lower energy consumption. Other types of heating systems combined with local radiant heating systems are also reviewed in this paper. According to reviewed studies, localized methods improved thermal comfort, and the same thermal sensation could be achieved in lower air temperatures, especially when using local radiant heating systems. To design local radiant heating systems properly, improvement of existing local thermal comfort and sensation modeling based on radiant heat transfer is needed. [ABSTRACT FROM AUTHOR]

• Experiment in three homes using mixed-methods and physical measurements. • Indoor air temperature fluctuations like those of EMPC of space heating. • Night setback-users found the heating control unacceptable. • Acceptance was motivated by economic or environmental benefits. Recent simulation-based studies have indicated that Economic Model Predictive Control (EMPC) of space heating systems can exploit the thermal mass in residential buildings for demand response (DR) purposes in district heating systems. However, there is a lack of studies on residents' perception and acceptance of the fluctuating indoor air temperature behaviour inherent in EMPC of space heating. This paper reports on a case study featuring the residents of three one-story houses located in Denmark. The houses were equipped with technology enabling remote actuation of radiator thermostats and collection of various indoor environmental data. Four different temperature boost interventions mimicking the typical behaviour of EMPC of radiators were executed while a mixed-methods triangulation design, employing questionnaires and semi-structured interviews, was used to collect subjective data. Data showed that residents accepted the behaviour but only after the benefits of the EMPC were explained. The acceptance was motivated by either the prospect of saving money, environmental benefits, or a combination of both. The results thereby indicate that explaining the benefits of EMPC is important if residents are to abandon their current preferences and practices in favour of an EMPC concept. The explanation should consider the diversity in current preferences, expectations, and level of technological pre-knowledge. In addition, the paper also reports on a range of findings related to technical aspects of realising EMPC in practice. [ABSTRACT FROM AUTHOR]

This paper investigates experimentally the cooling performance of a concept, where the radiant ceiling is suspended from the hollow-core concrete slab and by ventilation supply in the plenum and the perforations of the ceiling tiles, ventilation air is distributed without ducts and air terminals to the occupied zone. Literature has proven that this concept allows for more streamlined installation procedures and excellent performance in terms of thermal comfort and draught. The paper reports experimental results from a climate chamber, where the concept was tested under both steady-state and quasi-steady conditions. The steady-state conditions were chosen to map the cooling performance with different air change rates, and different ventilation and water supply temperatures. The results showed that for air change rates of 3 h−1 in the occupied zone and water supply temperature of 17 °C, the cooling output from the ceiling increased by 10 %. The concept was also tested under quasi-steady conditions in a 48 h cycle to quantify the thermal buffering effect of the exposed upper concrete slab when subjected to ventilation supply air. The effect amounted to 11–12 % increased cooling capacity at the end of the working day when the driving temperatures between air, water and thermal zones were at their maximum. [ABSTRACT FROM AUTHOR]

The capability to dynamically plan, predict, and control indoor conditioning allows to adapt to individual preferences of inhabitants and enables demand side management. While former mainly improves thermal comfort of inhabitants so does latter unlock ecological and financial opportunities mostly for energy utilities. Commonly, dynamic indoor conditioning is based on piece-wise constant indoor temperature constraints. This paper's contribution is the presentation of additional constraints: in particular ones expressed relative to the nominal behavior of a hydronic heating system. This allows to simultaneously harness the relevant process variables in particular during the pre-loading and post-loading phases of a load reduction. The findings are based on data sets acquired on 10 inhabited, residential buildings in Stockholm over a whole year. One of the findings is that building models need to be adaptable if predictive control is applied in practice. This adaptability is assured by a novel concept, i.e. a so called model manager on which the control is relying for the selection of the most accurate model. Centralized optimal control of buildings connected to a district heating network is challenging in practice due to a high computational load. In order to reduce it, the herein presented method elaborates plans only every hour instead of at every control step for optimal control. Since these plans cannot be optimal due to the lack of regular update a hitherto unknown cascaded control logic has been developed that corrects planning errors and other disturbances. Capabilities are demonstrated and compared to conventional controllers in dynamic simulations of a multi-zoned building. The herein presented method is to our knowledge the first to provide all flexibility desired by energy utilities and inhabitants alike through harnessing the consequences of transitions. [ABSTRACT FROM AUTHOR]

• Sleeping thermal comfort using a bed-based ASHP was numerically studied. • A digital thermal manikin (DTM) was used to simulate a sleeping person. • The PTS - WPD model was used to evaluate sleeping thermal comfort. • Four factors affecting sleeping thermal comfort were numerically analyzed. Sleeping is an important human activity and heating system is needed for a comfort sleeping thermal environment in winter. By combining the merits from both an air source heat pump (ASHP) and a Chinese-Kang heating system, a prototype bed-based ASHP (B-ASHP) system has been proposed, and several design/operating parameters were experimentally and numerically studied previously. A numerical study using a digital thermal manikin (DTM) on the impacts of four influencing factors, i.e., operating mode, bed surface temperature (t bed), thermal resistance of mattress (R mat), and thermal resistance of quilt (R q) on sleeping thermal comfort was carried out, and the study results are reported in this paper. The numerical study results suggested that firstly, to maintain a suitable sleeping thermal environment, the use of only the Horizontal section (H-Section) of the bed-based heating terminal of the B-ASHP system was adequate; however using the Horizontal and Vertical section (H + V-Section) could minimize the temperature difference between the micro-climate close to the bed and outside environment, although with a higher energy consumption. Secondly, t bed of the bed-based terminal should be carefully selected, and a t bed of 44 °C could both meet the requirement of thermal comfort and acceptable operating efficiency of the B-ASHP system. Thirdly, the use of a mattress would reduce the heat transfer from the bed-based terminal to a sleeping person and indoor space, however an excessively higher R mat of mattress would reduce the heating capacity and operating efficiency, leading to a cold sleeping environment. Finally, the use of a quilt would help prevent the heat loss from a sleeping person, thereby maintaining a warmer sleeping thermal environment, however a higher-than-necessary R q of quilt would decrease the sleeping thermal comfort. [ABSTRACT FROM AUTHOR]