Search

Temperature and humidity independent control (THIC) systems demonstrate promising energy-saving potential compared with the conventional air conditioning systems. One type of THIC systems is proposed to use dual cooling sources with different temperatures since they could be produced easily by traditional vapor compression refrigeration chillers. This paper investigates the applicable condition of the THIC system based on dual cooling sources (DCSTHIC system). It is found that the DCSTHIC system has limited conditions (such as scopes of the heat moisture ratio and the fresh air rate) when applied, otherwise the indoor air temperature and humidity can’t be fulfilled, and further available scope of the heat moisture ratio realized by the DCSTHIC system is disclosed for air conditioned spaces. The minimum realized heat moisture ratio depends on the temperature of low-temperature cooling sources ( t LCS ). A parametric study is also conducted to analyze effects on the energy efficiency of DCSTHIC systems. These parameters include the heat moisture ratio ( ε ) and temperatures of dual cooling sources. Results show that DCSTHIC systems show more significant energy-saving potential in the air conditioned spaces with higher ε . The system COP improvement ranges from 3.1% to 17.5% compared with conventional air conditioning systems when the heat moisture ratio changes from 8000 kJ/kg to 15,000 kJ/kg. This study helps to guide the design and optimization of DCSTHIC systems. [ABSTRACT FROM AUTHOR]

In order to optimize the global energy performance of a ground source heat pump system, special attention needs to be paid to the auxiliaries as they stand for a considerable part of the total energy consumption. A new in situ experimental methodology based on the frequency variation of the water circulation pumps in order to optimize the energy performance of the system was previously published by the authors for a ground source heat pump system using a single stage heat pump with ON/OFF regulation. The original single stage heat pump was recently replaced with a multistage unit consisting of two compressors of the same capacity working in tandem. A new experimental campaign was carried out and a new study was performed in order to adapt the in situ optimization methodology to the performance of the tandem compressors unit, and, by extension, to the multistage case. This paper presents the in situ optimization methodology for the water circulation pumps frequency adapted for multistage ground source heat pump systems. Results show that energy savings up to 32% can be obtained by applying this optimization methodology. [ABSTRACT FROM AUTHOR]

This paper develops a new process for identifying the lowest cost package of energy efficiency measures (EEM) and hybrid energy system configuration for off-grid homes. Hybrid energy systems, which combine two or more types of energy technologies, often require significant capital expenditure, however, the cost can be reduced by applying EEM to the house to decrease energy demand. The method proposed here, termed Combined Optimization Process (COP), was tested on an off-grid hypothetical case and incorporates an iterative assessment of a building energy and efficiency optimization tool (BEopt) and a hybrid system optimization tool (HOMER). The COP results were compared with the base case where no efficiency measures were applied, and also with a standard process, which involved a selection of best-practice efficiency measures. The COP method yielded net present cost savings of 10% less than the base case, and 5% less than the standard process. The COP method developed in this paper is applicable for existing houses converting to off-grid status as well as for the design stage of off-grid houses. [ABSTRACT FROM AUTHOR]

Abstract: Improving the heating performance of district heating networks (DHNs), one of the most important components in district heating systems, has significant influence on the promotion of energy efficiency. Based on the entransy theory, this paper develops an entransy dissipation-based method for global optimization of DHNs. We analyze the irreversibility of three types of heat transfer processes in DHNs: (1) the heat transfer process between the waters in primary heating networks and DHNs in substation heat exchangers; (2) the heat transfer process between supply water and indoor airs in radiators; and (3) the return water mixing process, then derive the expressions of entransy dissipation for each process, and finally deduce two different formulas of the total entransy dissipation in DHNs by the users’ demands and the structural and operating parameters of DHNs, respectively, from which we establish the mathematical relation between the users’ demands and the structural and operating parameters of DHNs. Based on this relation, two typical optimization problems of DHNs are converted into conditional extremum problems to deduce two optimization equation groups. Solving the equation groups gives the optimal structural and operating parameters for DHNs with highest energy efficiency. Finally, the method is proved valid and advantageous through the optimization for both 1-column-2-user and 2-column-4-user DHNs. [Copyright &y& Elsevier]

Abstract: Electric lighting consumes 19% of total electricity production worldwide. Open-plan offices constitute the majority of office stock, in which most office workers perform their daily tasks, and hence the lighting in those offices has significant impact on, not only energy usage, but also occupants’ productivity. This paper presents a unique lighting optimization approach for open-plan offices that is capable of tuning task lighting to each occupant''s preference in the most energy-efficient fashion. Exploiting individual controllability of the advanced networked lighting systems, each luminaire can be dynamically actuated at a different level to realize various lighting configurations without any physical rewiring. This research formulates lighting actuation into a linear programming problem and finds the optimal light outputs for each of the luminaires that collaboratively deliver specified lighting to each workstation while using the least amount of energy. Simulations using our lighting optimization approach have shown its versatility in providing proper workstation-specific task lighting under different requirements compared to business-as-usual practices. Energy savings are generated from tuning the light levels to occupants’ needs as well as keeping unoccupied areas unlit or minimally lit with this approach. [Copyright &y& Elsevier]