Search

The paper briefly describes energy-efficiency standards that have been issued for residential buildings in Northern and Central China as well as energy-efficiency inspection standards and specifications for renovation of existing residential heating systems in Northern China, and development of energy-efficiency standards for Southern China. The paper also describes barriers to improving the energy efficiency of residential buildings in China and strategies for overcoming these barriers, including reform of the method of payment for heating in Northern China. Finally, future prospects for further developing energy-efficiency standards for residential buildings in China are addressed. [Copyright &y& Elsevier]

Abstract: In this paper we undertake a comprehensive study to meet the building heating/cooling and power demand through a sustainable operation. We integrated polymer electrolyte membrane fuel cell (PEMFC) system and triple effect absorption refrigeration system (TEARS) for space cooling/heating and water heating applications in buildings. The analysis is carried out to observe the effects of different operating conditions on the efficiency of the fuel cell, output of the fuel cell and TEARS, and the utilization factor of the system. It is found that the efficiency, the utilization factor, and change in temperature of hot water increases from 36% to 48.8%, 49% to 86%, and 14K to 23K, respectively when the temperature of the cell is increased for different cooling loads and membrane thicknesses. In addition, the increase in membrane thickness affected the efficiency, the utilization factor, and change in temperature of hot water in a negative way and they were found to be decreasing from 47.3% to 42%, 85% to 49%, and 23K to 12K, respectively for different cooling loads. The water supplied to the house is obtained from a geothermal water source which makes the system more sustainable. [Copyright &y& Elsevier]

Abstract: Energy use in the built environment represents a large part of total energy use in Sweden and is one important sector where energy conservation needs to be significantly improved in order to meet the national implementation of the European goals. One key question that needs to be investigated in relation to these goals is the performance and implementation of passive or low-energy houses. This paper presents results and an evaluation of a newly built house in an area with passive houses in Linköping, Sweden. Nine passive houses were built with the aim to be energy efficient, with an annual space heating demand of 21kWh/m2, and at the same time to have the same visual appearance as any other building in the surrounding area. This study evaluates the energy performance of a residential area with low-energy buildings based on Building Energy Simulation (BES) (IDA ICE 4), and measurements from the real object. Both annual and hourly validation is performed using room by room modeling and internal heat gains. A novel approach to internal heat gain modeling is presented using time-use data (TUD). The results show possible improvements in the design, the building envelope and in the heating control. [Copyright &y& Elsevier]

Abstract: It is well known that it is necessary to insulate the buildings to decrease the thermal demand and to decrease the use of heating and cooling. Due to the high cost of fossil fuels and to the necessity to reduce CO2 emissions, and also due to the new building regulations more attention is paid to the insulation of buildings. Different insulation materials are available in the market. Usually, they are compared by their thermal conductivity and with theoretical calculations, but there are no experimental comparisons available, where the behavior of such insulation materials in a building is compared over time. This is why the authors started a comparison of three typical insulation materials, polyurethane, polystyrene, and mineral wool. For this purpose, four house-like cubicles were constructed (with a size of 2.4m×2.4m×2.4m) and their thermal performance throughout the time was measured. The cubicles were built under a conventional Mediterranean construction system, differing only in the insulation material used. During 2008 and the first months of 2009 the performance of these cubicles was evaluated, and the results are presented in this paper. [Copyright &y& Elsevier]

Abstract: This paper reports on an analytical investigation into the energy saving potential associated with modified comfort limits in transitional spaces in buildings. Such spaces may not require the same high level and close environmental control of more fully occupied spaces and thus a wider variation in conditions and interpretation of thermal comfort may be permitted. Estimations are made of energy saving potential based upon typical floor area proportions utilised for transition spaces of various types in office/commercial buildings. The data are combined with suggested norms for comfort expectation that have wider temperature limits than for normally occupied office zones. The method has been applied to a series of building types situated in the climate of the East Pennines area of the UK using a thermal analysis tool. The results show that useful energy savings (particularly for heating) are possible by allowing for a modest (and realistic) relaxation of prescribed comfort standards in transition spaces. Further work is now required to confirm the limits and assess energy saving in practice. [Copyright &y& Elsevier]

Abstract: An energy cost allocation system records the energy consumption of a building and divides the overall energy costs between the flats. Because the indoor temperatures of rooms are usually not equal, static heat flows between flats cannot be avoided. Hence, in order to ensure fair energy costs per flat the system should be able to determine the static heat flows, preferably without utilising in situ measurements. This paper presents a new method for estimating static heat flows between neighbouring rooms. The approach is theoretical, focusing only on heat transfer issues. Energy cost allocation is not considered. The approach is based on the parametric model describing thermal behaviour of an occupied space. The model is created for each room of a building. Parameter values are identified using real-time measurements collected by a building automation system from each room and its environment. The tuning of parameters takes a few days using a 15-min sampling time. A prerequisite for successful system identification is the overall control of the room temperatures. All test runs are performed in a simulated office hotel using the TRNSYS simulation program. The results are encouraging, but further research is needed, especially in a real building environment. [Copyright &y& Elsevier]