Search

Abstract: In the last years many studies concerning the evaluation of the thermal conductance of building elements via measurements have been carried out; this value has to be ensued from the analysis of recorded temperature and heat flux profiles. The determination of this property in situ would allow a more accurate a more accurate evaluation of the real heating energy demand of a building. Papers discussing different data analysis methods are present in literature and measurements on test components under real conditions and evaluations on different theoretical aspects by means of numerical simulations have been already developed. This paper aims at widening the existent literature of the in situ evaluation of the thermal conductance, through the discussion of the results of a measuring campaign which lasted four years on real buildings, and by comparing the reference specific thermal conductance (C) values with those computed on the basis of the measurements. Various tests on the same elements are discussed. Finally an analysis on the influence of the C value on the evaluation of the net heating energy demand of a building in different climates is presented. [Copyright &y& Elsevier]

Abstract: Recent results show that a predictive building automation can be used to operate buildings in an energy and cost effective manner with only a small retrofitting requirements. In this approach, the dynamic models are of crucial importance. As industrial experience has shown, modeling is the most time-demanding and costly part of the automation process. Many papers devoted to this topic actually deal with modeling of building subsystems. Although some papers identify a building as a complex system, the provided models are usually simple two-zones models, or extremely detailed models resulting from the use of building simulation software packages. These are, however, not suitable for predictive control. The objective of this paper is to share the years-long experience of the authors in building modeling intended for predictive control of the building''s climate. We provide an overview of identification methods for buildings and analyze their applicability for subsequent predictive control. Moreover, we propose a new methodology to obtain a model suitable for the use in a predictive control framework combining the building energy performance simulation tools and statistical identification. The procedure is based on the so-called co-simulation that has appeared recently as a feature of various building simulation software packages. [Copyright &y& Elsevier]

Evaluation methods can be used to determine what constitutes good energy performance in a building. With an increasing focus on energy use of buildings worldwide, this evaluation assumes a fundamental importance. This paper provides a comprehensive review of the available methods for analysing, classifying, benchmarking, rating and evaluating energy performance in non-domestic buildings. Methodologies are grouped in five categories: engineering calculations, simulation, statistical methods, machine learning and other methods. Techniques for evaluating buildings are described, their principal applications are shown and limitations are identified. The use of performance evaluation in energy efficiency programmes and standards is mapped. There is a need to further develop interactions between the main modelling techniques to produce simple, robust and validated models. Also, evaluation techniques must be developed to consider comfort or service provision in the buildings as a factor in energy performance. [ABSTRACT FROM AUTHOR]

Abstract: In the tropics, daylighting from a side window requires shading to intercept direct sunlight from the window whilst allowing penetration of daylight from sky. In this paper, daylighting from a double-pane glazed window with enclosed horizontal slats (slat window) was investigated for which it is situated on either north or south wall of a room. Full-scale experiments and simulations were conducted to characterize distribution of the interior daylight from the slat window under a real tropical climate. Performance of the slat window was evaluated in terms of the “useful daylight illuminance” (UDI), interior daylight availability and light power density (LPD) of an integrated dimmable lighting system. Empirical formulas were developed for determining annual average LPD values of the dimmable lighting system over its served area. The LPD value can be used with a reduced form of the energy equation of Thailand's building energy code to evaluate the reduced annual electrical energy consumption for accreditation of the daylight use in a building. The analysis of life cycle cost proved that the daylighting from the slat window integrated with the dimmable lighting system is cost effective. [Copyright &y& Elsevier]

Abstract: The building sector is an energy intensive sector, with great potential to reduce energy needs and environmental pollution. Several measures are being taken to increase the energy efficiency and avoid energy consumption in this sector. A recent trend is the nearly zero energy buildings, which was already adopted by some of the latest regulations, such as the 2010 recast of the European Performance of Buildings Directive (EPBD). However, to reach these goals, especially considering the existing building stock, new retrofit solutions are required, which must be well adapted to the specific building stock needs, and ensure that the building retrofit can achieve the nearly zero energy buildings standards. This paper presents a new prefabricated retrofit module solution for the facades of existing buildings, and also the steps taken to optimise its performance, which includes a judicious choice of materials, 3D modelling, cost–benefit analysis, use of different simulation tools for performance optimisation and prototyping. It is also shown the implementation of the retrofit module within an integrated retrofit approach, whose final goal was to obtain a building with the minimum possible energy consumption and greenhouse gas emissions. [Copyright &y& Elsevier]

Abstract: Many parameters have been used to evaluate the thermal performance of envelope wall/roofs, most of them for air-conditioned buildings. In this paper, the interest is focused on parameters to assess the thermal performance of envelope wall/roofs for non air-conditioned buildings. Five groups of parameters, some previously used and some newly proposed, have been analyzed. To test the evaluation parameters, numerical simulations of the periodic heat transfer through five different roof configurations have been carried out. This research shows the suitability of the energy transferred through the wall/roof during a day, the decrement factor, the discomfort degree hours, and the hot (or cold) thermal performance index to be used for thermal evaluation of wall/roofs in non air-conditioned buildings. The sensitivity of these parameters with climatic conditions and with the outdoor surface solar absorptance is analyzed. Additionally, it has been shown that the steady-state thermal transmittance, the thermal admittance modulus, the periodic thermal transmittance modulus, and the surface decrement factor, calculated with surface temperatures, are not suitable parameters to evaluate wall/roofs in non air-conditioned buildings. [Copyright &y& Elsevier]