Search

Current indoor thermal environment is usually automatically controlled based on a temperature set-point given by room occupants or building managers. However, investigation shows that many temperature set-points are far from the comfortable temperature range recommended by design handbooks. Such unreasonable temperature set-points will result in not only uncomfortable indoor thermal environment, but also waste of cooling or heating energy. The authors have proposed a methodology of satisfaction based control to take place of the traditional set-point based control. This paper describes the experimental comparison results between satisfaction based indoor thermal environment control and set-point based control. Two test-beds were set up and a series of experiments was conducted to compare control performances, user acceptances, user work performances and system energy consumptions of the set-point based and satisfaction based control. The comparison results show that the satisfaction based control can achieve more stable thermal environment. Both of the two control methods can get relatively high scores regarding user acceptance and work performance. There are no statistically significant differences for user acceptance and work performance between two control methods. However, satisfaction based control consumed 15.3% and 11.9% less energy at two test-beds respectively than set-point based control due to more reasonable temperature settings given by the satisfaction based control. [ABSTRACT FROM AUTHOR]

Abstract: A retrofit study was conducted in an unoccupied manufactured house to investigate the impacts of airtightening on ventilation rates and energy consumption. This paper describes the retrofits and the results of the pre- and post-retrofit assessment of building airtightness, ventilation, and energy use. Building envelope and air distribution systems airtightness were measured using fan pressurization. Air change rates were measured continuously using the tracer gas decay technique. Energy consumption associated with heating and cooling was monitored through measurement of gas consumption by the forced-air furnace for heating and electricity use by the air-conditioning system for cooling. The results of the study show that the retrofits reduced building envelope leakage by about 18% and duct leakage by about 80%. The reduction in the house infiltration rates depended on weather conditions and the manner in which the heating and cooling system was controlled, but in general these rates were reduced by about one third. The energy consumption of the house for heating and cooling was reduced by only about 10%, which is relatively small but not totally unexpected given that infiltration only accounts for a portion of the heating and cooling load. [Copyright &y& Elsevier]

Abstract: Energy use in the built environment represents a large part of total energy use in Sweden and is one important sector where energy conservation needs to be significantly improved in order to meet the national implementation of the European goals. One key question that needs to be investigated in relation to these goals is the performance and implementation of passive or low-energy houses. This paper presents results and an evaluation of a newly built house in an area with passive houses in Linköping, Sweden. Nine passive houses were built with the aim to be energy efficient, with an annual space heating demand of 21kWh/m2, and at the same time to have the same visual appearance as any other building in the surrounding area. This study evaluates the energy performance of a residential area with low-energy buildings based on Building Energy Simulation (BES) (IDA ICE 4), and measurements from the real object. Both annual and hourly validation is performed using room by room modeling and internal heat gains. A novel approach to internal heat gain modeling is presented using time-use data (TUD). The results show possible improvements in the design, the building envelope and in the heating control. [Copyright &y& Elsevier]

Abstract: This paper presents a detailed meta-analysis of end and primary energy use for heating, cooling and ventilation of 11 low-energy non-residential buildings and one residential building in Germany that belong to the EnOB research program launched by the German Federal Ministry for Economy. In particular, the analysis emphasizes the substantial impact of auxiliary energy use on the efficiency of heating and cooling performance. The investigated buildings employ environmental energy sources and sinks – such as the ground, ground water, rainwater and the ambient air – in combination with thermo-active building systems. These concepts are promising approaches for slashing the primary energy use of buildings without violating occupant thermal comfort. A limited primary energy use of about 100kWhprim/(m2 neta) as a target for the complete building service technology (HVAC and lighting) was postulated for all buildings presented. With respect to this premise, a comprehensive long-term monitoring in high time resolution was carried out over the course of two to five years, with an accompanying commissioning of the building performance. Measurements include the energy use for heating, cooling, and ventilation, as well as the auxiliary equipment, the performance of the environmental heat source and sink, and local climatic site conditions. [Copyright &y& Elsevier]

Abstract: The large thermal time constant of thermally activated building systems (TABS) hampers communication between the system''s production and emission. Therefore, conventional building control strategies, typically using room temperature feedback, are unadapted to control thermal comfort efficiently. In this paper, measurement data and simulation results reveal that unadapted TABS control has a dramatic impact on overall energy performance. Measurements in a TABS building with room temperature feedback show the HVAC system switching between heating and cooling in a very short time frame. A simplified, generic room model is used to simulate, understand and evaluate this behaviour. For room temperature feedback control, only 45% of the cold and 15% of the heat produced actually controls room temperature. The remainder is stored in the TABS and exchanged between the heating and cooling system. Enlarging the heating-to-cooling set point band improves this ratio, while maintaining thermal comfort. On the other hand, night time operation control of the circulation pump, adapted to the TABS thermal time constant, eliminates this ‘unused’ energy completely. In this case, however, even with perfect heat gain forecasts, it is difficult to avoid room temperatures dropping below thermal comfort limits during initial office hours. Hence, a supplementary air-conditioning system seems inevitable. [Copyright &y& Elsevier]

Abstract: Axiomatic design (AD) is a theory that helps to develop new design objects and allows one to evaluate the quality of designs. The aim of this paper is to apply this theory to the design of heat ventilation and air-conditioning (HVAC) systems and to come to conclusions about the design quality of some specific applications. The focus is the comfort and energy consumption in commercial buildings in South European climates. The discussion contains a brief description of variable air volume (VAV) systems and dedicated outdoor air systems (DOAS) with terminal units, such as fan-coils, induction units and chilled ceilings. Occasionally, the DOAS design should include over-cooled outdoor air in order to ensure an extra cooling means. According to the AD''s first axiom, ideal systems are independent or decoupled. Our conclusion is that VAV and DOAS with induction units are coupled designs, and on the other end, DOAS with fan-coils or chilled ceilings are decoupled designs. In addition, over-cooling outdoor air (OA) flow couples the OA flow with the indoor heat removable needs. [Copyright &y& Elsevier]