Search

Increase in cooling energy usage of the residential sector in Hong Kong has been moderate in the most recent ten years (2004–2013). Factors and drivers responsible for this are of interest to policy makers in search of performance improvement but such information is not available in extant literature. This paper reviews the policy instruments introduced in Hong Kong during this period of time and examines the different engineering factors contributing to improvements in cooling energy efficiency. Whether the policy instruments have been instrumental in bringing about changes in engineering design and thus improvement in cooling energy efficiency is evaluated on the basis of the equipment and building envelope characteristics of 64 residential developments in Hong Kong. Different statistical analyses reveal that the use of more energy efficient room air-conditioning units (COP), smaller window-to-wall ratios (WWR) and walls with higher U-values are the engineering factors (WallU) that have contributed to moderation of growth of energy consumption; these were driven by policies introduced by the Hong Kong Government. Regarding the sensitivity of the three engineering factors, it was found that COP was the highest amounting to 0.455, followed in descending order by WallU and WWR. Their sensitivities were 0.289 and 0.006, respectively. [ABSTRACT FROM AUTHOR]

Nearly 60% of electrical energy use in Hong Kong is for space conditioning during summer months. The paper investigates the impact of design-related variables on outdoor micro level daytime heat island effect in residential developments in Hong Kong. The paper hypothesizes that the differences in outdoor temperatures within and between residential developments can be explained by the impact of design-related variables on the overall environment. Case studies of three large housing estates reveal urban heat island effect (UHI) in the order of 1.5 °C within an estate, and 1.0 °C between estates. The results indicate that energy efficient designs can be achieved by manipulating surface albedo, sky view factor and total height to floor area ratio (building massing) while maximizing cross ventilation. [Copyright &y& Elsevier]

Abstract: This paper presents a simplified energy performance assessment method for existing buildings in cooling season, which is based on energy bill disaggregation and energy performance analysis. This method requests very limited building energy data and can effectively assess the energy performance at building and system levels, and disaggregate the whole-building consumption into consumptions of three groups of end-uses. This method is based on two basic energy balance principles, i.e., the electricity consumption balances at building level and the cooling energy balances between demand side and supply side of HVAC systems. An optimization algorithm is developed to establish best possible cooling energy balances by minimizing the balance residuals and therefore to disaggregate the energy consumption of different users. The performance of the proposed method was validated in two existing buildings in Hong Kong and Beijing. The results, including the disaggregated energy consumptions and the key energy performance indicators of HVAC system, agreed well with the “measured” data in mechanical cooling months. [Copyright &y& Elsevier]

Abstract: In sub-tropical city of Hong Kong where summer is hot and humid, the usage of outdoor spaces is often hindered due to thermal discomfort. In order to improve the thermal comfort of the outdoor environment and to make urban outdoor spaces delightful places for people to use and enjoy, better understanding of the thermal perception of people is needed. This paper presents the results of an outdoor thermal comfort study conducted in Hong Kong. The findings of the study reveal that air temperature, wind speed and solar radiation intensity are influential factors in determining the thermal sensation of people outdoor. Based on our analysis, the neutral physiological equivalent temperature (PET) in summer in Hong Kong is around 28°C. Under shaded condition, a wind speed of 0.9–1.3m/s is needed for a person in light clothing to achieve neutral thermal sensation in an urban environment. This understanding can contribute towards establishing wind performance standards for thermal comfort in hot and humid tropical and sub-tropical cities. [Copyright &y& Elsevier]

Abstract: In Hong Kong, conventional air-conditioning (AC) systems cause a high energy consumption and poor indoor thermal comfort. This paper investigated the AC load profiles of three typical local commercial buildings, i.e. office, hotel and retail, and examined the energy consumption of liquid desiccant cooling system (LDCS) for these buildings. Simulation results showed that the cooling load contributed to more than 98% of total annual load, with high latent load proportion from March to September. The high reheating ratio, i.e. from 60% to 90%, is found to be the main reason for the poor thermal comfort. Therefore, the LDCS which could handle sensible and latent loads separately was proposed. However, the electricity-driven LDCS was found not suitable for local commercial buildings. significant energy saving could be achieved by the solar-assisted LDCS system with thermal storage, when the installation area for solar collectors is larger than the minimum required one, i.e. 9.7m2/(kWm−2) for office and 12.7m2/(kWm−2) for hotel buildings. Energy saving of different system types with different installation areas was also studied. The solar-assisted LDCS shows more energy saving in winter but less in summer. Results and conclusions can be useful for researchers and local engineers. [Copyright &y& Elsevier]

Abstract: Evacuated tube solar water heaters are increasingly in use in Hong Kong because of their good thermal efficiency and high water temperature achievable as compared to the flat-plate solar water heaters. But so far their thermal performance has not been systematically evaluated and therefore not well known to the users. This paper reports our experimental and numerical works on evaluating the performance of the two common types of evacuated tube solar water heaters for domestic hot-water applications. These are the single-phase open thermosyphon system and the two-phase closed thermosyphon system. Our results show that the daily and annual thermal performance of the two-phase closed thermosyphon solar collector is slightly better than the single-phase open thermosyphon design. But the payback periods of the two are relatively the same because of the higher initial costs of the two-phase closed thermosyphon collector system. Although economically they are less attractive than the flat-plate type collector system, they are suitable for applications in advanced systems with higher temperature demands. [Copyright &y& Elsevier]

Abstract: The concern on climate change leads to growing demand for minimization of energy use. As building is one of the largest energy consuming sectors, it is essential to study the impact of climate change on building energy performance. In this regard, building energy simulation software is a useful tool. A set of appropriate typical weather files is one of the key factors towards successful building energy simulation. This paper reports the work of developing a set of weather data files for subtropical Hong Kong, taking into the effect of future climate change. Projected monthly mean climate changes from a selected General Circulation Model for three future periods under two emission scenarios were integrated into an existing typical meteorological year weather file by a morphing method. Through this work, six sets of future weather files for subtropical Hong Kong were produced. A typical office building and a residential flat were modeled using building simulation program EnergyPlus. Hourly building energy simulations were carried out. The simulated results indicate that there will be substantial increase in A/C energy consumption under the impact of future climate change, ranging from 2.6% to 14.3% and from 3.7% to 24% for office building and residential flat, respectively. [Copyright &y& Elsevier]

Abstract: It becomes popular to use computer simulation technique to evaluate the performance of energy utilizations in buildings. The hourly weather data as simulation input is a crucial factor for the successful energy system simulation, and obtaining an accurate set of weather data is necessary to represent the long-term typical weather conditions throughout a year. This paper introduces a stochastic approach, which is called the first order multivariate Markov chain model, to generate the annual weather data for better evaluating and sizing different energy systems. The process for generating the weather data time series from the multivariate Markov transition probability matrices is described using 15-years actual hourly weather data of Hong Kong. The ability of this new model for retaining the statistical properties of the generated weather data series is examined and compared with the current existing TMY and TRY data. The main statistical properties used for this purpose are mean value, standard deviation, maximum value, minimum value, frequency distribution probability and persistency probability of the weather data sequence. The comparison between the observed weather data and the synthetically generated ones shows that the statistical characteristics of the developed set of weather data are satisfactorily preserved and the developed set of weather data can predict and evaluate different energy systems more accurately. [Copyright &y& Elsevier]

Abstract: Urban heat island can significantly increase the demand for cooling of buildings in cities. This paper investigates one of the main causes of the urban heat island phenomenon, i.e. reduced city ventilation. Two simple Hong Kong city models with relatively complex terrain were considered here under different atmospheric conditions. A 3D RNG k–ɛ turbulence model was used for modeling turbulence effects. The simulation results showed that the influence of thermal stratification can be significant on city ventilation driven partially by thermal buoyancy. When the wind speed is relatively large, the impact of thermal stratification on air flow in city street canyons is minor. When the wind speed is small relative to the buoyancy force, the airflow in the street canyons is dependent on thermal stratification. When there is an adverse vertical temperature gradient, the greater the instability, the stronger the vertical mixing and the greater the flow rate caused by turbulence. The heat and pollutants can easily accumulate under stable atmospheric conditions when there is only a weak background wind or none at all. [Copyright &y& Elsevier]

Abstract: The purposes of this paper are to analyze winter energy use of residential buildings in different cities of China, and to figure out the influence factors of winter residential energy use. The investigated residences were located in seven typical cities of five architectural thermotechnical design zones. Questionnaire surveys revealed building characteristics, household characteristics, the utilization of domestic appliances, and thermal environment in winter. Winter energy consumption in different cities bears obvious regional characteristics. In south China, Hong Kong has the largest mean household energy use amount, and Changsha and Chongqing follow Hong Kong; Kunming in the warm zone has the small energy use. In north cities, if district space heating is excluded from total energy use, Urumqi and Xi’an have the energy use at the smallest level, but space heating use is very huge. The energy use amounts of space heating of Tangshan, Urumqi and Xi’an are several times as large as the amounts of all the end uses in the southern cities. The analysis on influence factors of winter energy use are made for Chongqing and Hong Kong, respectively, by Quantification Theory I, and the results show there exist obvious differences in influence factors between the two cities. [Copyright &y& Elsevier]

Abstract: The shading-type building-integrated photovoltaic (BIPV) claddings can act as power generators as well as external shading devices of a building, which reduce the energy consumption of the building. However, there is little information about energy impacts of different tilt angles of the shading-type BIPV claddings. By considering the typical meteorological conditions of Hong Kong, the energy performance of the shading-type BIPV claddings, in terms of the electricity generation and the cooling load reduction, is analyzed in this paper. The optimum tilt angle of PV modules for maximum electricity generation is found to be 20° instead of local latitude. Combining electricity generation and cooling load reduction, it can be concluded that the optimum tilt angles for the first type of the shading-type BIPV claddings vary from 30° to 50°, while the optimum tilt angle for the second type is 0°. [Copyright &y& Elsevier]

Abstract: Double skin façade can be defined as a building façade covering one or several stories with multiple skins. The skins may be air tight or ventilated. With sophisticated study and design, buildings constructed with double skin façade can have better thermal performance than the conventional single skin façade. This paper reports the findings on the energy performance of double skin façade applied to a typical office building under the climatic condition in Hong Kong. An experimental setup was established and the measured data were used to verify the theoretical model developed via the EnergyPlus simulation program. The validated model was then used to evaluate the energy performance of double skin façade with various configurations including glazing type (clear, absorptive or reflective glass), glazing position (inner or outer pane) and glazing layers (single or double glazing material). The results indicate that a double skin façade system with single clear glazing as the inner pane and double reflective glazing as the outer pane can provide an annual saving of around 26% in building cooling energy, as compared to a conventional single skin façade with single absorptive glazing. However, the long payback period of 81 years makes the double skin façade system economically infeasible. Support and motivation are needed from the local government in order to foster successful and widespread application of the double skin façade system in buildings. [Copyright &y& Elsevier]

Abstract: A benchmark study of the energy efficiency of private office buildings in Hong Kong was conducted in 2002 because energy efficiency was declining. In the study, private office buildings were divided into five user groups. For each group, a multiple regression model was developed to find the relationship between Energy Use Intensities (EUIs) and other factors, such as operating hours, for normalization and benchmarking purposes. In this paper we make use of the regression results to study the energy efficiency of private office buildings by different grades. In Hong Kong, office buildings are divided into three grades (A, B, and C) based on the quality of the facility, which is reflected in rental values; a Grade A office building denotes expensive luxury. We found that the EUI of Grade A office buildings is the highest, consuming over 50% of the total energy used in office buildings. Recently, the annual EUI of office buildings has improved even though Grade A floor space is increasing. This may be due to the promotion of the energy efficiency program launched in the last decade. [Copyright &y& Elsevier]

Abstract: Mandatory energy codes to curb energy use of residential buildings have been formally launched in China for more than two decades but little has been publicized in literature. Similar codes are not available for residential buildings in Hong Kong, but most residential buildings in Hong Kong, especially public housing estates, are HK-BEAM certified to demonstrate their compliance with regulatory and basic design requirements. Given HK-BEAM is internationally recognized and there are doubts about the effectiveness of the China codes, how the energy efficiency of the HK-BEAM certified buildings compare with buildings in compliance with the China codes is of interest to most building designers and policy makers. This paper describes how the energy efficiency of a case study building in compliance with the China codes compare with the one in compliance with HK-BEAM. The energy simulation by HTB2 and BECRES reveal that the case study building in compliance with the China codes is 51.1% better in energy use. In the study, the relative impact of each compliance criterion on energy use and cooling load has been quantified by sensitivity analysis. The sensitivity values indicate that energy use is most sensitive to air-conditioning operation hours, indoor design temperature, coefficient of performance (COP) of the room air-conditioners (RAC) units, and the envelop characteristics. The results of this study indicate that a HK-BEAM certified building cannot satisfy the China codes requirements. This provides good reference to the policy makers, the building owners, and to the China and Hong Kong Governments when considering reciprocal recognition of building energy codes. [Copyright &y& Elsevier]

Abstract: PV ventilated glazing technology for application in warm climate provides energy saving opportunities through the reduction in air-conditioning load, the daylight utilization, and the green electric power generation. In a working environment, the use of semi-transparent a-Si glazing is deemed better than the one with non-transparent c-Si solar cells. This paper reports an evaluation of its integrated performance using a small office room in Hong Kong as an example. An energy model of a PV ventilated window system is first introduced. Based on this together with the TMY weather data of Hong Kong and the daylight simulation capability of the EnergyPlus program, the overall performance analysis have been executed for different window orientations. It was found that a solar cell transmittance in the range of 0.45–0.55 could achieve the best electricity saving. [Copyright &y& Elsevier]

Abstract: Near-extreme outside dry- and wet-bulb temperatures are essential for the design of building HVAC systems. Coincident design temperatures currently defined by ASHRAE and CIBSE may not fully allow engineers to design an HVAC system that can match a risk level desired for the problem at hand. A rational method is therefore presented in this paper for the proper selection of coincident climate design conditions, which is based on the theory of probability. An average statistic risk level has been proved to be approximately equal to the annual percentile of coincident dry- and wet-bulb temperatures for HVAC systems whose thermal time constant is less than 1h. An algorithm is also developed to determine the contours of equal risk. Representative coincident design dry- and wet-bulb temperatures are obtained through statistic analysis of the 15 years of weather records in Hong Kong. These rationally derived outside design temperatures are compared with the coincident dry- and wet-bulb temperatures currently defined by ASHRAE and CIBSE. [Copyright &y& Elsevier]

This paper firstly presents a case study on analyzing the electrical load profiles recorded in a Hong Kong hotel over a period of 12 months to examine the potential energy saving opportunities (ESOs) in its building services installations. The case study is followed by a report of the survey results of energy and water use in 36 quality hotels in Hong Kong. Finally, a regression analysis where the surveyed energy and water use data were correlated to a number of hotel background or operational parameters to search for suitable energy and water use performance explanatory indicators is presented. The survey results depict a diversified energy and water use situation in Hong Kong’s hotels, but the regression analysis indicates that, while some of the correlations obtained are weak, there do exist a few strong energy and water explanatory indicators. [Copyright &y& Elsevier]