Search

Understanding the features of the hydrocarbon generation and expulsion of the Upper Triassic Xujiahe Formation (T3x) source rocks is important to properly guide petroleum exploration in the Xujiahe Formation in the Sichuan Basin. Based on mass balance, the hydrocarbon generation and expulsion from the T3x source rocks are characterized in this paper through a method (i.e., hydrocarbon generation potential index using pyrolysis data) different from that used in previous studies. The threshold and peak of hydrocarbon expulsion are determined to be Ro = 0.9% and 1.15%, respectively. The amounts of hydrocarbon generated and expelled in the T3x source rocks are 4,525.5 × 108 and 2,420.5 × 108 t, respectively. Moreover, three hydrocarbon expulsion regions T3x have been identified in the Sichuan Basin. On the basis of the hydrocarbon generation and expulsion features of the source rocks and the distribution of the oil‐and‐gas reservoirs, the quantitative model of the hydrocarbon accumulation probability under the control of the T3x source rock is established via single‐factor regression analysis. The predictions obtained through this analysis show that the favourable oil‐and‐gas exploration areas in the Xujiahe Formation are distributed in the Qionglai, Chengdu, and Deyang regions, as well as in the west of Yilong region. Further, the results show that 78% of the discovered oil‐and‐gas reservoirs are located in the predicted favourable and relatively favourable oil‐and‐gas exploration areas. [ABSTRACT FROM AUTHOR]

Reservoir quality is critical in tight gas exploration. A systematic study of the petrological, petrophysical, and diagenetic characteristics of the Shanxi Formation sandstones in the north‐eastern Ordos Basin (China) was undertaken to characterize the pore system of these tight sandstones and recognize the distribution of reservoirs favourable for hydrocarbon accumulation. The results suggest that the Shanxi Formation sandstone has low compositional and moderate textural maturity, with its porosity ranging from 0.7% to 11.8% (average 5.97%) and permeability ranging from 0.001 to 2.77 mD (average 0.36 mD). In addition, thin section and SEM observations suggest that the sandstone is dominated by secondary dissolution pores, primary intergranular pores as well as microfractures, and has undergone compaction, cementation, and dissolution. Diagenetic minerals, such as carbonate cements, authigenic quartz, clay minerals, and dissolved feldspar, are identified. Fluid inclusions are observed in healed microfractures of quartz grains and in quartz overgrowths, while the homogenization temperatures of fluid inclusions in healed microfractures and in quartz overgrowth are in the ranges of 92.8–179.1°C (average 134.8°C) and 104.7–169.1°C (average 145.7°C), respectively. Authigenic kaolinite is sourced from the process of K‐feldspar dissolution, authigenic illite is sourced from transformation of smectite and kaolinite, while sources for quartz cements include mineral alteration and pressure dissolution. Selective dissolution of K‐feldspar in the presence of carbonate minerals is observed in the Shanxi Formation tight sandstones due to the different equilibrium constants of carbonate minerals and K‐feldspar leaching, resulting in dissolution pores associated with K‐feldspar. Reservoir quality in the Shanxi Formation tight sandstones is greatly influenced by diagenesis, as compaction and cementation are responsible for the loss of porosity while dissolution accounts for the enhancement of secondary porosity. [ABSTRACT FROM AUTHOR]

The north‐eastern Ordos Basin in Central China has become an exploration target in recent years due to the potential of natural gas resources in the Upper Palaeozoic strata. In this study, by analysing the geochemical characteristics of the source rocks and the natural gas, the genesis of the Upper Palaeozoic natural gas was identified. In addition, the accumulation process was discussed by combining studies of hydrocarbon generation and burial/thermal history. The results reveal three sets of source rocks developed in the study area—Carboniferous Benxi (C2b), Permian Taiyuan (P1t), and Shanxi (P1s) formations—consisting of mudstones, carbonaceous mudstones, and coals. The source rocks contain abundant Type III organic matter and have entered mature to high‐mature stage, while source rocks in the south‐eastern part of the study area have entered the overmature stage due to the activity of Zijinshan magmatic rocks. The natural gas has a high content of methane (average 93.99%). The stable carbon isotope of methane (δ13C1) value (average −37.05‰) and that of ethane (δ13C2) value (average −26.4‰) and the composition of the light hydrocarbons reflect the idea that the natural gas is organic in origin, thermogenic, and mainly terrigenous‐sourced. The evolution of a transitional to continental depositional environment of the source rocks results in the variation in the geochemical characteristics of the Upper Palaeozoic gas in the study area. Analysis of fluid inclusions indicates a long and continuous period of natural gas charging in the study area from 165 to 65 Ma. Sandstone bodies close to or interbedded with the source rocks made the gas charging from the source rocks to the reservoirs over a short distance with high efficiency, while faults and fractures provided paths for the gas migrating to reservoirs vertically far from the source rocks. The huge gas generation potential of the source rocks and continuous distribution pattern of sandstone bodies provides favourable conditions for the development of a large‐scale natural gas reservoir. [ABSTRACT FROM AUTHOR]

The recent gas exploration in West China demonstrated that formation conditions of tight‐sandstone gas are distinct from typical ones in North America. One remarkable difference is that complicated tectonic conditions in the foreland basin of West China, especially the Himalayan tectonic movement, resulted in widely developed fractures in tight‐sand reservoirs. Thus, this work employed dual media to characterize tight‐sand reservoir system and explain the impact of dual media on tight‐sand gas reservoir by: (a) describing the feature of fractures and properties of Yinan 2 tight‐sand reservoir; (b) characterizing dual media with mercury intrusion porosimetry, full diameter and conventional core analysis; (c) discussing gas charging and accumulating in dual media based on the difference between dual media and tight‐sand rocks. Observation from cores, FMI images and thin sections suggested that macro‐ and micro‐fractures are widely distributed in Lower Jurassic Ahe Formation (J1a) tight sandstones, with dip angle of 70° to 80°. These fractures are strongly scale‐dependent with length of several centimetres to a few tens of centimetres and apertures of several hundreds to several thousands of microns. J1a tight‐sand reservoir is characterized by poor porosity, with an average value of 7.7%, whereas measured permeability varies from 0.01–100 mD. Intrusion and extrusion curves of dual media and tight‐sand rocks are significantly different from each other, while displacement pressure and medium saturation pressure of dual media are lower than tight‐sand rocks. Importantly, maximum pore throats of dual media are 1.75–32.22 times larger than juxtaposed tight‐sand rocks. The ratio of permeability between dual media and tight sandstone is up to 1,000, whereas the ratio of porosities only ranges from 1 to 1.5. Thus, dual media in tight‐sand reservoir represents high permeability system and matrix pores are primarily storage system. The impact of dual media on tight‐sand gas reservoir involves its position, temporal coupling of gas charging and growth. In terms of fracture growth prior to gas charge, multi‐force can work together as a driving force, and fractures as a flow system and matrix pores as a storage system linked by fractures; buoyancy is the primary driving force in fractures. In terms of gas charge prior to fracture growth, dual media can also exert a positive impact on gas charging when occurring in the inner part of tight‐sand reservoir defined by the critical throat threshold. However, dual media can also destroy the "inverted gas–water" and shrink tight‐sand gas reservoir when occurring at the original critical throat threshold. [ABSTRACT FROM AUTHOR]

Abundant shale oil resources were recently found in the organic‐rich Permian Lucaogou (P2l) Formation shale, Jimusar Sag, Junggar Basin. Although some scholars have conducted some researches on the basic geochemical characteristics of the Lucaogou Formation shale, it is not enough to effectively guide the shale oil exploration in the area. This is because during the exploration process of shale oil, besides the basic geochemical characteristics of shale, its mineral composition, physical properties, and oil‐bearing characteristics are all very important evaluation parameters. To systematically evaluate the favourable shale oil exploration sections in the Lucaogou Formation, 265 pieces of shale cores were sampled from well Ji174 in this study. Besides the basic geochemical characteristics of the 265 pieces of cores, the mineralogical, petrophysical, and oil‐bearing characteristics were also analysed. Results show that the shale has abundant organic matter (average total organic carbon 3.51%, average petroleum generation potential 15.67 mg/g), dominated by Type II1 and Type II2 kerogen, and has entered the early‐mature to mature stage. The Upper Member of the Lucaogou Formation has relatively higher organic matter and organic matter type is relatively more oil prone compared to the Lower Member; however, organic matter thermal maturity is lower. The P2l Formation shale is characterized by high carbonate minerals and low clay minerals, and when considering mineralogical brittleness, both the Upper and Lower members are ideally fracturable in shale oil development. The P2l Formation shale has a wide porosity range (1.1–13.9%), and the Lower Member's porosity is slightly greater. The inversion of shale porosity in the P2l Formation is controlled by the differentiated mineral composition. The oil saturation index values of the Lower Member shale are significantly greater than the Upper Member shale. From the above, the Lower Member of the P2l Formation shale is ideally suited and has greater shale oil potential in the Jimusar Sag, Junggar Basin, especially in the depth intervals of 3,255–3,272, 3,282–3,298, and 3,317–3,334 m in the well Ji174. [ABSTRACT FROM AUTHOR]

Recent exploration has revealed the great potential of gas resources, complicated gas distributions and geochemical characteristics of natural gases in tight sandstones of the West Sichuan Basin, China (WSBC). The chemical, stable carbon and light hydrocarbon compositions of natural gases from WSBC were investigated to assess the genesis, sources, and migration pattern leading to variations in the geochemical and stable carbon isotope compositions. The analysis shows that the natural gas in the Jurassic tight sandstones occurs as dry gas or wet gas in some places; however, most of the gas in the deep Triassic tight sandstones is apparently dry gas. Carbon isotope distributions increased in the order δ13C1 < δ13C2 < δ13C3 < δ13C4. The light hydrocarbon content increased in the order of chain (i.e. non-cyclic) alkanes, cycloalkanes, and aromatic hydrocarbons. Relatively high ethane carbon isotope values and methylcyclohexane contents indicated the presence of lacustrine coal-formed gases. The Jurassic natural gas is in a lower thermally mature stage and possibly originated from a mixture of T3X3 and T3X5 black mudstones. The deep Triassic natural gas was possibly originated in the deep source rocks because the gas has a relatively higher thermal maturity. Positive correlations between burial depth and methane content, dryness coefficient, δ13C1, and δ13C1-δ13C2 for the deep Triassic gas suggest that the migration distance was short and the source was nearby or the gas accumulated in situ. The chemical compositions and geological studies revealed that the fractionation of the Jurassic natural gases in a tight reservoir was predominantly caused by vertical migration rather than the maturity of the local source rocks. Copyright © 2016 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

Understanding hydrocarbon migration mechanism is a key scientific problem that needs to be resolved for effective hydrocarbon exploration in the Ordovician rocks of the Tazhong area, Tarim Basin. Based on analyses of geological setting and reservoir distribution characteristics, hydrocarbon migration process, and mechanisms in the Ordovician, Tazhong area, were investigated by integrating geological, geophysical, and geochemical parameters. Successfully analysed parameters included logging reservoir properties, seismic attributes, production outputs, fluid properties, and hydrocarbon maturity parameters. Results indicate that hydrocarbons were introduced into the Ordovician through a series of charging positions during 3 accumulation periods - middle Caledonian, late Hercynian, and Himalayan. In total 11 hydrocarbon charging positions were identified at intersection zones of the northeast-trending faults and northwest-trending flower strike faults. There are anomalies in all parameters on hydrocarbon charging positions. With increasing distance from the charging positions, anomalies of oil density, wax content, dry gas coefficient, hydrogen sulphide content, gas/oil ratio, well production, 4-/1-MDBT ratio of crude oil weakened, and natural gas' carbon isotope composition becoming lighter along a northwest to southeast direction are present. Evidence from main hydrocarbon pathway systems theory, formation mechanisms of fault intersection zones, and obvious improvement in reservoir properties at intersection zones supports this viewpoint. Further exploration activities in the Ordovician of the Tazhong area should be conducted in the North Slope's west area, and intersection zones in tectonic up-dip direction should be emphasized. Copyright © 2016 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

Significant progress has recently been made in tight oil exploration within the Permian Lucaogou (P2l) Formation of the Jimusar Sag. However, current tight oil exploration deployment of the P2l Formation is mainly based on reservoir prediction, which is high risk for tight oil exploration. In this study, the geological and geochemical characteristics of the P2l Formation source rocks, including the distribution, sedimentary environment, organic matter abundance, kerogen types and thermal maturity were investigated. Hydrocarbon generation and expulsion intensity were evaluated through an improved hydrocarbon generation potential methodology, and the significance of source rocks in tight oil source and occurrence was systematically investigated. Results indicate that P2l Formation source rocks with total organic carbon >1.0 wt% occur widely (an area up to 1500 km2), are thick (up to 160 m), were deposited in a lacustrine weakly reducing sedimentary environment with relatively low salinity, have a high total organic content with a mean value of 3.12 wt%, are dominated by type II kerogen and have reached the early mature to mature stage. Modelling results indicate that the source rocks reached the hydrocarbon generation threshold and hydrocarbon expulsion threshold at 0.48% and 0.86% vitrinite reflectance, respectively. The comprehensive hydrocarbon expulsion efficiency was approximately 30%, and the maxima of hydrocarbon generation and expulsion intensities for P2l Formation source rocks are 1200 × 104 and 425 × 104 t/km2. The tight oil is sourced from adjacent source rocks that are interbedded with, or are close to, the reservoirs. The migration of oil generated from the source rocks occurs over very short distances. The oil filling degree index (oil bearing thickness/P2l Formation thickness) is higher at a closer proximity to the source rocks, and where it is higher the hydrocarbon generation intensity of the source rocks is also elevated. In addition, the greater the hydrocarbon expulsion intensity of the source rocks, the higher the daily oil production values (ton/day) from prospect wells. Copyright © 2016 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

The lower limit of hydrocarbon accumulation in the Kuqa Depression is investigated. The Kuqa Depression in the Tarim Basin is one of the largest gas-producing regions in China. High yields of hydrocarbons have been found in depths below 7000 m, which suggests that the deep strata have great potential for hydrocarbon exploration. However, for effective deep exploration, the effective limits such as maximum depth or minimum physical properties of reservoirs have not yet been established. The lower limit of hydrocarbon accumulation, i.e. the conditions at which hydrocarbon accumulation is no longer possible, is determined by analysing the characteristics of effective reservoir space, reservoir permeability, fluid potential differences inside and outside the reservoir, and drilling results of exploratory wells in actual geological conditions. Research shows that the lower limit of hydrocarbon accumulation is reached when irreducible water saturation reaches 100%, reservoir permeability reaches as low as 0.01 × 10−3 µm2, fluid potential ratio of outside to inside the reservoir (fluid potential ratio of the surrounding rock to sandstone reservoir) is less than 5.5, and exploratory wells reach reservoirs that are all dry layers. From these four aspects, the lower limit of hydrocarbon accumulation corresponds with reservoir porosity of approximately 2.5%, permeability of approximately 0.01 × 10−3 µm2, pore throat radius of approximately 0.003-0.004 µm, and burial depth of approximately 8200 m. Determining the lower limit of hydrocarbon accumulation in the Kuqa Depression will contribute to predicting favourable exploration areas and evaluating effective resources. Copyright © 2016 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

Combined with the actual geological settings, tight oil is the oil that occurs in shale or tight reservoirs, which has permeability less than 1 mD and is interbedded with or close to shale, including tight dolomitic oil and shale oil. The Fengcheng area (FA), at the northwest margin of the Junggar Basin, northwest China, has made significant progress in the tight oil exploration of the Fengcheng (P1f) Formation recently, which indicates that the tight oil resources have good exploration prospects. Whereas the lack of recognition of hydrocarbon generation and expulsion characteristics of Permian P1f source rocks results in the misunderstanding of tight oil resource potential. Based on the comprehensive analysis of geological and geochemical characteristics of wells, seismic inversion, sedimentary facies, tectonic burial depth, etc., the characteristics of P1f source rocks were investigated, and the horizontal distributions of the following aspects were predicted: the thickness of source rocks, abundance and type of organic matter. And on this basis, an improved hydrocarbon generation potential methodology together with basin simulation techniques was applied to unravel the petroleum generation and expulsion characteristics of P1f source rocks in FA. Results show that the P1f source rocks distribute widely (up to 2039 km2), are thick (up to 260 m), have high total organic content (TOC, ranging from 0.15 to 4 wt%), are dominated by type II kerogen and have entered into low mature-mature stage. The modeling results indicate that the source rocks reached hydrocarbon generation threshold and hydrocarbon expulsion threshold at 0.5% Ro and 0.85% Ro and the comprehensive hydrocarbon expulsion efficiency was about 46%. The amount of generation and expulsion from the P1f source rocks was 31.85 × 108 and 15.31 × 108 t, respectively, with a residual amount of 16.54 × 108 t within the source rocks. Volumetrically, the geological resource of shale oil is up to 15.65 × 108 t. Small differences between the amounts calculated by the volumetric method compared with that by hydrocarbon generation potential methodology may be due to other oil accumulations present within interbedded sands associated with the oil shales. Copyright © 2015 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

Although it has been shown that the potential of tight-sand gas resources is large, the research into the mechanisms of hydrocarbon charging of tight sandstone reservoirs has been relatively sparse. Researchers have found that there is a force balance during hydrocarbon charging, but discriminant models still have not been established. Based on the force balance conditions observed during gas migration from source rocks to tight sandstone reservoirs, a calculation formula was established. A formula for identifying effective source rocks was developed with the gas expulsion intensity as the discrimination parameter. The critical gas expulsion intensity under conditions of various burial depths, temperatures, and pressures can be obtained using the calculation formula. This method was applied in the Jurassic tight sandstone reservoirs of the eastern Kuqa Depression, Tarim Basin, and it was calculated that the critical expulsion intensity range from 6.05 × 108 m3/km2 to 10.07 × 108 m3/km2. The critical gas charging force first increases with depth and later decreases with greater depths. The distribution range of effective gas source rocks and total expelled gas volume can be determined based on this threshold. This method provides new insight into and method for predicting favourable tight-sand gas-bearing regions and estimating their resource potentials. Copyright © 2014 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]