Search

This paper proposes a LLC type resonant forward converter using adjustable turning-off time control for low power and voltage applications. The new circuit is derived from the conventional LLC converter, and it has simple structure while maintaining decent soft-switching characteristics. The switching losses are reduced by ZVS (zero voltage switching) and ZCS (zero current switching). Also, regulation of the output voltage does not require a small ratio between magnetizing inductor and resonant inductor, so the leakage inductor of transformer can be utilized instead of an external inductor to realize resonance, which makes it possible to use only one magnetic component in the resonant topology. Besides, the adjustable turning-off time control strategy is adopted in the scheme, which optimizes the switching condition while ensuring the wide range operation. In comparison to the traditional PWM (pulse width modulation) control, the proposed control strategy can further reduce the switching loss and improve power efficiency. This is also suitable for the utilization of GaN (gallium nitride) devices due to the requirement of higher switching frequencies at wide input applications. In addition to the detailed theoretical analysis, the validity of the proposed concept is confirmed by the experimental results of a prototype. [ABSTRACT FROM AUTHOR]

This paper presents a novel control technique for a wide output voltage range digitally controlled SIDO boost converter. It employs minimum phase conditions reported in refid="ref1"/ , refid="ref2"/ and extends the same to SIDO boost converter to eliminate the effect of RHP zero. Further, the proposed work employs input-output linearization technique refid="ref3"/, refid="ref4"/ to linearize the control-to-output transfer function across different operating points to achieve improved stability under unbalanced loads and a wide output voltage range on each output of the proposed SIDO boost power converter. The SIDO boost regulator was verified experimentally for an input voltage of 3.3 V and a maximum simultaneous load current of 350 mA on each output. Measurement results demonstrate that the proposed design achieves a wide output voltage range of 4.8 V–13.75 V, with ability to dynamically transition across these different output voltages in both small and big voltage steps. [ABSTRACT FROM AUTHOR]

It is essential to retain improved efficiency in a dc–dc converter over a wide load current range to extend the battery-life in portable devices. This requires a multi-mode controller, consisting of pulse-width-modulation (PWM) and pulse-frequency-modulation (PFM) schemes. However, existing approaches attempt to integrate structurally different controllers; thus it is difficult to achieve a seamless controller transition. While a digital platform offers controller configurations, it remains difficult to identify a suitable digital PWM/PFM technique and decide on its sampling mechanism to achieve stable behavior. This paper proposes a unified digital PWM/PFM scheme which shares a common digital PWM (DPWM) block and has the provisions for online controller configuration and automatic (switching) frequency adaptation. The proposed scheme retains improved efficiency over a wide operating range and inherently achieves seamless controller transitions. Further, a unified discrete-time framework is proposed for the analysis and design of the proposed multi-mode controller. Buck and boost converter prototypes are tested and the proposed controller is implemented using a field-programmable-gate-array device. [ABSTRACT FROM AUTHOR]

Active pulse-width-modulated (PWM) voltage rectifiers are commonly used to convert ac power from a three-phase grid to a regulated dc voltage with unity input power factor. The output voltage regulation is normally achieved by an outer voltage feedback loop and a sinusoidal pulse-width-modulated (SPWM) inner current loop. Due to output voltage disturbances, such as those produced by a capacitive load, the inner current loop can be easily driven into over-modulation and possible six-step operating regions. Current research efforts have focused on extending the linearity of the modulated voltage in the over-modulation range to reduce the input current harmonics and on studying the closed-loop stability via conventional small-signal linearization around a fixed operating point. Such linear techniques obviously fall short of predicting large-signal transient stability. In this paper, catastrophic bifurcation of the three-phase voltage-source converter is reported. The physical origin of the phenomenon is identified. Boundaries of catastrophic bifurcation in the parameter space are derived. The phenomenon has been verified experimentally. [ABSTRACT FROM PUBLISHER]

A floating buck controlled multi-mode dimmable light-emitting diode (LED) driver that uses a stacked NMOS switch is presented, which reduces static operational current and eliminates auxiliary winding to simplify design and cost. The accuracy of the output current benefits from the use of a line-voltage compensation technique which can mitigate the effect of line-voltage fluctuation on current consistency. The proposed LED driver is implemented in 0.5 \mum 5V/40 V backend 2P2M CMOS process and occupies a die size (with pads) of 1.17\times 0.84\ mm^2. The experimental results show that the proposed LED driver achieves peak power efficiency of 95.4% across a wide range of input voltage from 85 to 264 Vac and a wide range of series-connected load LEDs from 11 to 27. The worst-case line regulation and load regulation of the output current are 0.28% and 0.25%, respectively. Measurements further show that the startup time is only 34.8 ms at 220 Vac with 50 Hz-input and multi-mode dimming can be easily implemented. [ABSTRACT FROM AUTHOR]