Search

This paper considers the finite-order filter design problem for the source and multiple full-duplex (FD) relays in a cooperative communication system under frequency-selective fading channels. The goal is to optimize the source and relay filters such that the end-to-end signal-to-interference-plus-noise ratio (SINR) of minimum mean-squared error decision-feedback equalizer (MMSE-DFE) can be maximized. The resultant design problem is very difficult since we need to deal with self interference (SI), inter-relay interference (IRI), and inter-symbol interference (ISI) at the same time. Novel designs are then proposed to overcome the difficulty in this work. Transforming the signals into the frequency domain and using some optimization techniques, we first theoretically derive the power spectrum of the source filter and the spectrums of the relay filters. Then, the finite-order design is developed to approach the derived spectrums. Based on the weighted least-square (WLS) criterion, the Steiglitz-McBride method is exploited to obtain the filter coefficients in finite lengths. Numerical results demonstrated that complete removal of SI may not be a good strategy; preserving a certain amount of SI at each relay instead provides better SINR performance. [ABSTRACT FROM AUTHOR]

Full-duplex transmission is a promising technique to enhance the capacity of relay communications. In this paper, we investigate the power and location optimization for full-duplex decode-and-forward (DF) relaying systems. The outage probability is adopted as the optimization criterion and a two-dimensional (2D) optimization problem is formulated for systems with and without the direct source–destination link. Analytical and numerical results are provided to demonstrate advantages of the power and location optimization. More interestingly, the effect of residual self-interference (RSI) introduced by full-duplex transmission is investigated in terms of the optimal power allocation and relay location deployment and the outage probability performance improvement. Furthermore, we show that the minimal outage probability can be achieved via joint power-location optimization. The effect of power optimization on the outage performance is also compared between full-duplex and half-duplex relaying. [ABSTRACT FROM AUTHOR]

This paper presents an optimization framework for a wireless sensor network whereby, in a given route, the optimal relay selection and power allocation are performed subject to signal-to-noise ratio constraints. The proposed approach determines whether a direct transmission is preferred for a given configuration of nodes, or a cooperative transmission. In the latter case, for each node, data transmission to the destination node is performed in two consecutive phases: broadcasting and relaying. The proposed strategy provides the best set of relays, the optimal broadcasting power and the optimal power values for the cooperative transmission phase. Once the minimum-energy transmission policy is obtained, the optimal routes from every node to a sink node are built-up using cooperative transmission blocks. We also present a low-complexity implementation approach of the proposed framework and provide an explicit solution to the optimization problem at hand by invoking the theory of multi-parametric programming. This technique provides the optimal solution as a function of measurable parameters in an off-line manner, and hence the on-line computational tasks are reduced to finding the parameters and evaluating simple functions. The proposed efficient approach has many potential applications in real-world problems and, to the best of the authors' knowledge, it has not been applied to communication problems before. Simulations are presented to demonstrate the efficacy of the approach. [ABSTRACT FROM AUTHOR]

Large-scale propagation effect plays an important role in multiple-input multiple-output (MIMO) relay systems. In particular, the position of the relay (between the source and destination) determines the path-loss effects of adjacent hops, which will further affect the performance of each hop and thus the relay system. In this paper, by minimizing the outage probability of a decode-and-forward (DF) MIMO relay system with orthogonal space-time block coding, we show that relay position optimization improves the finite-SNR (signal-to-noise ratio) diversity gain of a relay system whose adjacent hops have different diversity orders (unbalanced system). Specifically, with relay position optimization, the diversity gain is no longer bounded by that of the weaker hop, i.e., the hop with a lower diversity order, but approaches the diversity order of the stronger hop. This diversity improvement provides a dramatic improvement for the end-to-end outage probability. It will also be shown that although power allocation has no effects on the achievable diversity order, it provides some SNR gains. [ABSTRACT FROM AUTHOR]

This paper presents a joint subcarrier and power allocation algorithm for cooperative multiuser orthogonal frequency division multiplexing (MU-OFDM) cognitive radio (CR) systems. By simplifying a three-node relay network to a two-node network with the equivalent channel gain, we formulate the resource allocation problem for a cooperative MU-OFDM CR system in a similar form to that for a non-cooperative MU-OFDM CR system. With this problem formulation, a rule is derived for performing subcarrier assignment operations under a given power distribution, where the sum capacity optimization is alternated between the subcarrier and power to form a joint subcarrier and power allocation algorithm. To simplify the high-complexity optimal power allocation algorithm (i.e., the iterative partitioned water-filling algorithm) for the joint scheme, we further develop a simple method for updating the water level when each subcarrier is assigned. Simulation results show that, with or without cooperative transmission, using the proposed method to update the water level achieves a system capacity close to that of the joint subcarrier and power allocation algorithm with the optimal power distribution. In addition, if the relay node is at the midpoint between the source and destination, the system capacity can reach its maximum value. [ABSTRACT FROM AUTHOR]

In this paper, we consider beamforming (BF) for cooperative networks with one multi—antenna source, multiple multi—antenna amplify—and—forward (AF) relays, and one single—antenna destination. The source BF vector and the AF—BF matrices at the relays are optimized for maximization of the signal—to—noise ratio (SNR) at the destination under three different power constraints. In particular, we consider individual relay power constraints, a joint relay power constraint, and a joint power constraint for the source and the relays. We solve the associated optimization problems in two stages. In the first stage, we find the optimal AF—BF matrices for a given BF vector at the source. For the cases of individual and joint relay power constraints, closed—form solutions for the AF—BF matrices are provided, respectively. Furthermore, for the case of a joint source—relay power constraint, the AF—BF matrices are obtained in closed form up to a scalar power allocation factor and an efficient numerical algorithm for the power allocation between the source and the relays is given. In the second stage, the optimal source BF vectors are computed. Thereby, we show that for the joint relay and the joint source—relay power constraints, the resulting problem can be transformed into a non—convex polynomial programming problem which allows for an exact solution for small—scale networks. For large—scale networks and networks with individual relay power constraints, we propose efficient suboptimal optimization methods for the source BF vector. Simulation results show the benefits of having multiple antennas at the source and/or multiple multi—antenna relays and illustrate the performance differences introduced by the three different power constraints. [ABSTRACT FROM AUTHOR]