Search

Partial discharge (PD) in gas insulated switchgear (GIS) has been studied extensively under AC voltage or transient voltage applied alone. However, the transient voltage in an actual system is superimposed on the AC operating voltage, which has rarely been studied. In this paper, the effect of AC and switching impulse superimposed voltage on PD characteristics was studied in SF6 gas. A test platform of generating superimposed voltage with controllable phase was used to study free particle and floating potential defect models. When the AC voltage was 90 and 110% of PD inception voltage (PDIV), the standard switching impulse with amplitude of about twice the PDIV was superimposed on different phases of the AC voltage. When the AC voltage is below the PDIV, results show that PDs of free particle defect model can be initiated when switching impulse is superimposed on 45 and 90° of AC. The PDs in the subsequent cycles of AC reignited into a self-sustaining discharge. For the floating potential defect, PDs have a marked difference duration, which is initiated by switching impulse in different phase. However, there is no change in PDs in each model when the AC voltage is above the PDIV. [ABSTRACT FROM AUTHOR]

Recent studies suggest that fluoronitriles compound Novec 4710 possesses a dielectric strength two times higher than that of SF6, while with a low global warming potential of only 2400. Mixed with CO2 buffer gas, the Novec 4710 mixtures offer excellent dielectric properties and the possibility to be used as an eco-friendly alternative to SF6 for medium voltage switchgears. This paper focuses on the comparative study of the breakdown strength and partial discharge (PD) characteristics between the fluoronitrile/CO2 mixtures and SF6 under AC voltages. Breakdown tests are conducted under different electrode configurations, i.e., planeplane, sphere-plane, rod-plane, and needle-plane, at different pressures and electrode gaps. In the uniform field, equivalent dielectric strength to SF6 at 100 kPa can be reached by a mixture containing 15% fluoronitrile at identical total pressure; while in non-uniform and highly non-uniform fields, SF6 exhibits higher dielectric strength than 20% mixture. The PD analysis suggests that SF6 has much more PDs with lower magnitude and the 20% fluoronitrile/CO2 mixture has less PDs but with higher magnitude. Due to the different PD characteristics, the corona stabilization effect may be responsible for the higher breakdown strength of SF6 under highly non-uniform field. [ABSTRACT FROM AUTHOR]

The objective of this paper is to investigate the effect of a high-frequency high-voltage impulse conditioning technique on the inrush current interruption phenomena. In this paper, the inrush current interruption phenomena referred to the actual interruption and the currentless period following interruption. First, Six 7.2 kV vacuum interrupters (VIs) were conditioned by 400 batches of voltage impulses. The duration of each batch were set to 0.1 s. The peak value of each impulse could reach up to 100 kV. The repetition frequency of the impulse was set to 1000 Hz. The contact gap was 0.8 mm. The VIs were tested for the inrush current interruption performance with inrush current set to 2 kA and 5 kA, with a frequency of about 3800 Hz. The experimental results showed that there were two different types of inrush current interruption depending on high-frequency high-voltage impulse conditioning. The inrush current interruption type I referred to the inrush current interruption during the prestrike process before the contacts touched. This type inrush current interruption could be caused by the erosion of prestrike arc. Moreover, the high frequency voltage impulse conditioning influenced the occurrence frequency, the number of interruptions and the duration of the inrush current interruption type I. The inrush current interruption type II referred to the inrush current interruption during the contact bouncing process after the contacts touched. The inrush current interruption type II occurred only in the case of the VIs after conditioning. Furthermore, the occurrence frequency of the inrush current type II decreased with increasing inrush current. [ABSTRACT FROM AUTHOR]

Vacuum circuit breakers are widely used in medium-voltage class. In vacuum circuit breakers, restrikes and non-sustained disruptive discharges sometimes occur after current interruptions. It is said that these late breakdowns are triggered by the microparticles. This paper aims to investigate the relationship between the motion of microparticles and subsequent late breakdown phenomena. It does by artificially injecting microparticles into the vacuum gap and observing their motion using a highspeed video camera. We focused on the sputtering of the electrode material during the current interruption and the mechanical stress of the switching operation as being the origin of these microparticles. We found that the motion of microparticles can be grouped into two distinct patterns: bouncing and attaching. Bouncing microparticles seem to be made of metal, while most of the attaching microparticles attached themselves to the cathode, and their charge was about five times greater than that of the bouncing microparticles. The attaching microparticles seem to be positively charged by secondary electron emissions from the surface under electron bombardment due to the field emission current from the cathode. From these results, we believe that the surfaces of the attaching particles are covered with an insulating layer. From our observations of the production of microparticles by mechanical stress, we have found that the breakdown voltage of the gap drastically drops after a mechanical switching operation where microparticles are produced. The breakdown voltage is restored with repetitive mechanical switching operations and subsequent voltage application. However, the breakdown voltage drops again when the operating speed of the electrode is increased. We also found that microparticles are scattered from the cathode spots on electrodes that have not been current-conditioned, and they are hardly produced from electrodes that are current-conditioned. From these results, we believe that controlling the speed of the mechanical switching operation and the current conditioning are effective ways to prevent the microparticles from being produced. [ABSTRACT FROM AUTHOR]

The past and recent investigations show that front time of switching overvoltage waveforms in Ultra High Voltage (UHV) system of long distance transmission are mostly in long wave front time exceeding 1000μs. The long front time of switching impulse voltage has been deviated from the critical front time. This paper is involved with breakdown characteristics and external insulation design under long front switching impulse voltage in UHV system. All the Tests were performed on an outdoor UHV test site at altitude of 2100 m, China Southern Power Grid Co. Ltd. (CSG). Breakdown characteristics of rod-plane and actual size tower-conductor in /spl l.chemo/800 kV UHV DC transmission line are obtained under wide front time switching impulse voltages from 100 to 2350 μs. From the comprehensive studies of such tests, it is proposed that U50 of front time exceeding 1000 μs increases 20% compared with the results of standard switching impulse (250/2500 μs) tests and standard deviations of U50 is 6% in UHV transmission system. Finally, an air gap insulation design procedure in conductor-tower of UHV transmission line at altitude of 0-2000 m is presented. Long front time switching impulse strength of conductor-tower gap is proposed into selection by reference in UHV transmission line insulation design. [ABSTRACT FROM AUTHOR]

The objective of this paper is to investigate an impact of the inrush current on the prestrike and restrike characteristics of vacuum interrupters (VIs) during capacitive current switching duty. Eleven 7.2 kV VIs are used. Their contact parameters are contact gap 4 mm and contact material CuCr25 (25%weight of Cr). A series of 80 CO operations are executed for each test VI. The amplitude of inrush current Iinrush (3800 Hz) is set to 0 kA, 2 kA, 5 kA and 10 kA, respectively. The switching current is less than 1 A rms. The (1-cosωt) shape of the recovery voltage with a peak of 15 kV is applied to the test VI. The experimental results show that the prestrike and restrike phenomena are significantly influenced by the contact surface conditions damaged by the inrush current. The cumulative probability of the prestrike gap dpre follows a 3- parameter Weibull distribution. When Iinrush increases from 2 kA to 5 kA, the prestrike gap increases accordingly. The 10% dpre increases from 0.5 mm to 0.7 mm. The 50% dpre increases from 0.7 mm to 1.0 mm. The 90% dpre increases from 1.0 mm to 1.5 mm. The scale in the Weibull distribution, which can describe the scattering of dpre, is 0.2 mm and 0.6 mm in the case of Iinrush = 2 kA and Iinrush = 5 kA, respectively. It is found that the occurrence frequency of the inrush current interruption increases from 37.9% to 68.3% with the increase of Iinrush from 2 kA to 5 kA. Moreover, the inrush current also has an impact on the restrike types, which are classified into three types according to the waveform features. The average restrike probability increases from 4.6% to 17.9% and further to 30.4% with the increase of the inrush current from 0 kA to 2 kA and 5 kA, respectively. In addition, the higher the inrush current, the restrike tends to occur earlier during the recovery voltage period. [ABSTRACT FROM AUTHOR]

Capacitor charging power supply (CCPS) is one of the most important components of a pulsed power system. The CCPS studied in this paper is used in power conditioning systems for Laser Nuclear Fusion. With a view to enabling multiple CCPSs to work concurrently in an environment of high voltage, high power and strong electromagnetism, this paper carries out a profound and systematic research into the characteristics of a capacitor charging power supply, including charging rate, harmonic features, efficiency and voltage precision, etc. Furthermore, some measures to improve the characteristics of CCPS are put forward. The advantages of high charging rate, low harmonic, high efficiency and accurate charging voltage are proved by the results of experiments and the performance in practical operation on a 23.5 kV, 50 kW, 4400 μF CCPS. [ABSTRACT FROM AUTHOR]

Research efforts at Texas Tech University on impulse antenna phased array has resulted in the development of a dependable high voltage, high repetition rate switch that can minimize jitter into the ps range. To accurately synchronize a phased array to steer and preserve the risetime of a radiated pulse, the jitter can only be a fraction of this risetime. Initial testing with a similar system in [1] produced sub-ns jitter results for operations in different gases and gas mixtures. This paper discusses in detail 50 kV, 100 Hz switch operations using different testing parameters. The switch jitter as a function of triggering conditions is discussed, including a comprehensive evaluation of jitter as a function of operation pressure as well as trigger magnitude. Several phenomenon were observed and discussed to quantify the switch jitter with respect to operation pressure and trigger magnitude. The temperature of gas and its effects on switch jitter is also documented in this paper, with a jitter improvement of ~25% recorded. An empirical formula was determined as a function of the gas density, electric field of the main gap, and electric field for the trigger for the experiments conducted in this manuscript. A 50 Ω, 1 nF pulse forming line is charged to 50 kV and provides the low inductance voltage source to test the switch. The hermetically sealed spark gap, with a modular design composed of copper tungsten electrodes, gas feeds, Kel-F lining, as a well as a G-10 shell is used to house the high pressure gases for the experiments. Trigatron-type triggering is provided by a solid state opening switch voltage source that supplies 75-150 kV, 10 ns risetime pulses at a rep rate up to 100 Hz in burst mode. [ABSTRACT FROM AUTHOR]

In this paper athree-stage pulse generator architecture capable of generating high voltage, high current pulses is reported and system issues are presented. Design choices and system dynamics are explained both qualitatively and quantitatively with discussion sections followed by the presentation of closed-form expressions and numerical analysis that provide insight into the system?s operation. Analysis targeted at optimizing performance focuses on diode opening switch pumping, energy efficiency, and compensation of parasitic reactances. A compact system based on these design guidelines has been built to output 8 kV, 5 ns pulses into 50 ?. Output risetimes below 1 ns have been achieved using two different compression techniques. At only 1.5 kg, this light and compact system shows promise for a variety of pulsed power applications requiring the long lifetime, low jitter performance of a solid state pulse generator that can produce fast, high voltage pulses at high repetition rates. [ABSTRACT FROM AUTHOR]

In this paper, a compact repetitive nanosecond pulsed power generator based on transmission line transformer (TLT) is developed for non-thermal plasma generation. The high voltage capacitor, the spark gap switch and the input side of the TLT are built into a compact structure to obtain a fast high-power pulse. The properly designed magnetic cores placed around the coaxial cables of the TLT have been chosen to obtain a higher voltage gain. The layout of TLT is optimized to make the generator more compact. Experiment test shows that voltage pulses of 30 kV with rise time of about 25 ns, pulse duration of about 100 ns, pulse repetition rate of 500 pps have been achieved. [ABSTRACT FROM AUTHOR]

In this paper, the method of reducing the rise time of high-voltage pulse transformer output rectangular pulses using a magnetic compression switch has been studied. An equivalent circuit consisting of pulse transformer and magnetic switch was used to describe the behavior of a transformer operating with magnetic switch. Meanwhile, four simplified equivalent sub-circuits and corresponding differential calculation models were used to analysis the influence of the magnetic switch module on the waveform characteristics of load resistance. The simulation and experiment results showed that the rise time of rectangular pulses could be reduced from more than 1 ?s to less than 150 ns while keeping pulse duration constant which was considered as the principle of rectangular pulse sharpening. Moreover, the pulse waveform performance on load resistance was determined by the pulse transformer, magnetic switch module and their coupling effects. [ABSTRACT FROM AUTHOR]

This paper presents a novel topology for the generation of high voltage pulses that uses both slow and fast solid-state power switches. This topology includes diode-capacitor units in parallel with commutation circuits connected to a positive buck-boost converter. This enables the generation of a range of high output voltages with a given number of capacitors. The advantages of this topology are the use of slow switches and a reduced number of diodes in comparison with conventional Marx generator. Simulations performed for single and repetitive pulse generation and experimental tests of a prototype hardware verify the proposed topology. [ABSTRACT FROM AUTHOR]

This paper describes the operation of a solid-state series stacked topology used as a serial and parallel switch in pulsed power applications. The proposed circuit, developed from the Marx generator concept, balances the voltage stress on each series stacked semiconductor, distributing the total voltage evenly. Experimental results from a 10 kV laboratory series stacked switch, using 1200 V semiconductors in a ten stages solid-state series stacked circuit, are reported and discussed, considering resistive, capacitive and inductive type loads for high and low duty factor voltage pulse operation. [ABSTRACT FROM AUTHOR]

A triggered vacuum switch (TVS) is one of the important apparatuses in the field of pulsed power system. It has many advantages, such as wide working voltage range, high current capability, high transfer charge, flexible trigger system, high trigger reliability, rapid dielectric recovery, long life, compact fabric, low noise, etc. A small and compact sample of surface-breakdown TVS with six-gap rod electrode system was fabricated in this paper, and a test platform of TVS was set up. The test results show that, the TVS sample has working voltage of 0.05-28 kV, current peak of 225 kA and transfer charge of 45Cb. Due to the ceramic surface in the trigger gap, the time delay of TVS is controlled in less than 1.5μs, and long trigger life is in prospect. Lastly, the working polarities are discussed, showing that the positive working mode is more reliable and advantageous. [ABSTRACT FROM AUTHOR]