Search

Nowadays, reliability of power system is of great importance. Therefore, the condition of transformers as the expensive and critical components of a power system should be monitored and assessed. The dominant factor that causes limitation in transformers lifetime is the paper insulation. This paper aims to investigate the conspicuous influence of moisture content, especially in low oxygen and temperature on lifetime estimation under constant conditions, based on the results of previous experiments. Degree of polymerization (DP) is employed to quantify the effects of detrimental parameters with respect to their time-varying nature. This paper proposes a novel lifetime estimation-approach considering a yearly moisture growth for transformers. The results indicate different trend of DP profiles, which lead to an accurate lifetime estimation in comparison with DP obtained through ideal conditions. Furthermore, oscillations in the hot-spot temperature of transformers are demonstrated to have a negative effect on the lifetime. [ABSTRACT FROM AUTHOR]

This paper discusses the effect of temperature on polarization and depolarization current measurements on paper oil insulation system. The influence of copper sulphide formed due to corrosive sulphur in mineral oil, on the changes in polarization and depolarization current at different temperatures are considered. A significant increase in the magnitude of polarization and depolarization currents due to deposits of copper sulphide on paper layers is observed. The conductivity of paper insulation increases significantly with increase in temperature. The increase in current is attributed to thermally active conducting particles of copper sulphide. The Debye model parameters of equivalent circuit under copper corrosion have been computed and a model for failure due to copper sulphide is explained using the data on polarization and depolarization currents. [ABSTRACT FROM PUBLISHER]

The oil-paper insulation of valve-side windings in a high voltage direct current (HVDC) converter transformer is subjected to both complicated voltage and severe thermal stresses. Partial discharge (PD) occurring in oil-paper bounded cavities is influenced by voltage stress type as well as temperature. This paper presents PD behaviors in an oil-paper bounded gas cavity under pulsating DC voltages. The voltage across the gas cavity and PD inception voltages at different test conditions are analyzed. Influences of temperature on statistical PD distributions and parameters are also presented. A numerical model is used to interpret PD behaviors under pulsating DC voltages and various temperatures. Experimental results and theoretical statements show that the temperature exhibits a great influence on the behaviors of cavity discharge under pulsating DC voltages. Volume resistivity, gas pressure, charge decay time constant, and electron generation rate are the primary parameters influencing PD behaviors at different temperatures. [ABSTRACT FROM PUBLISHER]

Furfural content in oil is a valuable indicator of cellulose paper degradation and is widely utilized in aging assessment for power transformers. However, with the same aging degree of insulation paper, the actual furfural content in oil is influenced by temperature because furfural partitioning behavior in the oil-paper insulation system of power transformers changes with temperature. Thus, correction of the temperature effect on furfural partitioning is crucial for accurate assessment of the aging of power transformers. In this research, oil-paper samples with different furfural contents were prepared through an accelerated thermal aging test. A furfural equilibrium experiment was conducted at different temperatures to construct a furfural partitioning diagram. The mass fraction of furfural in oil and paper was calculated. Results showed that the mass fraction of furfural in oil increases with temperature rising and aging deepening, which means that furfural tends to migrate from paper to oil at high temperatures and deep aging conditions. The change in furfural partitioning between oil and paper at different temperatures causes a deviation in paper aging assessment. To correct the temperature effect on furfural partitioning, a furfural correction factor was developed to normalize furfural contents in oil at different temperatures to a reference temperature. The furfural correction factor was verified by experimental data and then introduced into the relation between degree of polymerization of paper and furfural content of oil. Verification results showed that the corrected equation can enhance the accuracy of paper aging estimation at different temperatures. The findings of this work indicated temperature effect on furfural partitioning should be considered when determining the furfural thresholds and evaluating the aging condition of power transformers. [ABSTRACT FROM PUBLISHER]

The application of vibration-based condition monitoring methods to power transformers has shown the potential for detecting mechanical transformer failures. The ageing of winding insulation paper, which is a common problem in long-serving power transformers, affects both the electrical and mechanical strength of the windings. This paper is concerned with the vibration features of winding disks with aged insulation paper. The vibration characteristics of single-layer winding disks wrapped with insulation paper are investigated. By examining the vibration frequency responses of winding disks with different degrees of ageing of insulation paper, the effects of aged paper on the vibration behaviors of winding disks are demonstrated. The experimental results show that changes in the vibration responses of winding disks can be related to the ageing of insulation paper, and thus it is possible to detect this failure mode in a power transformer using a vibration-based method. A qualitative explanation for these changes is presented, using the degradation of the mechanical strength of the insulation paper. [ABSTRACT FROM AUTHOR]

Oil-paper insulation, as a major insulation mode used in power transformers, is continuously and unavoidably subjected to repeated lightning impulses, which may bring potential risk to the insulation system. Therefore, in this work, accumulative effect of repeated lightning impulses and its damage mechanism in oil-impregnated paper (OIP) are investigated. Firstly a repetitive impulse accumulating test platform was set up, and tests were performed to confirm the existence of accumulative effect of repeated lightning impulses. Then atomic force microscope observation and frequency domain spectroscopy were carried out on OIP samples with different times of lightning impulses, based on which the influence of lightning impulses accumulative effect on surface morphology and dielectric properties of OIP was investigated. The results indicate that repeated lightning impulses produce accumulative damage to the OIP and hence lead to the morphology change and generation of translucent gelatinous substance on the sample surface. Both the surface roughness and dielectric parameters increase with the accumulating of repeated lightning impulses, which can be attributed to the effects of polar products, fiber deformation and the translucent gelatinous substance together. At last, the possible mechanism of the accumulative effect was discussed and relevant tests were carried out to verify the speculation. [ABSTRACT FROM PUBLISHER]

The iso-margin method based on the classical analytical equations is widely used in the development of extra high voltage (EHV) bushing. Therefore, its effectiveness and feasibility have been fully validated. However, with the theoretical formula, it is difficult to evaluate the influence of stray capacitance and temperature on the internal electric stress of the ultra high voltage (UHV) bushing. It?s necessary to further improve the traditional iso-margin method. Firstly, the basic principle of iso-margin method has been briefly described. After that, the E-field distribution of condenser bushing was investigated on the Finite Element Method (FEM) computing platform. Then, the mathematical model of the advanced equal margin design method was established. Furthermore, this paper presents the program flow of optimization which combines the simulation of electro-thermal coupling process and the particle swarm optimization (PSO) algorithm. The proposed methodology was applied to the design of the prototype of the UHV resin impregnated paper (RIP) oil-SF6 bushing, which realizes the uniform axial E-field distribution of the bushing condenser. Meanwhile, the partial discharge margin between adjacent foils can be equal. Moreover, the hot-spot temperature is lower than the operation limiting temperature of the RIP material. The bushing condenser was fabricated according to the optimal structure design. The prototype of bushing has passed through all the type tests. In this paper, the FEM electro-thermal coupling simulation and the advanced equal margin design method were applied to the inner insulation structure optimization of the UHV RIP oil-SF6 bushing. Meanwhile, the proposed methodology provides some theoretical guidelines for the future research and development of other types of bushing on the UHV level. [ABSTRACT FROM AUTHOR]

Heretofore, unlike HVAC transformers, there is not much experience in both insulation design guides and test methods for ultra HV converter transformers. This special insulation phenomenon is very prominent due to the complication of voltage applied on valve-side windings of converter transformers. There is a severe lack of empirical research on partial discharge in oil-paper insulation under the combined ACDC voltage. The study in this paper provides a timely research into the issues. Nine possible configurations, which intent to simulate different defects in the transformer, have been investigated. The PD inception voltages varied ratios of combined AC-DC voltages were conducted. The discharge magnitude and its relation with the applied voltage for selected four common configurations were obtained during voltage increasing and decreasing respectively, which presented the PD initiating process and also reflected the insulation behavior of dielectrics. Besides, the Finite Element Analysis Soft was used to propose the effect of morphology of electrode surface (3 dimensional roughness is approximately 0.03 mm) on PD characteristics, which is very lacking in the previous references. The roles of DC and AC component in PD characteristics were discussed in the context of the relevant work in literatures. [ABSTRACT FROM AUTHOR]

Copper sulfide deposition on cellulosic insulating materials in oil-immersed transformers is evaluated by heating tests stipulated by IEC 62535. Although this method is suitable for evaluation of the corrosivity of unused insulating oil, the subject remains in diagnosis of the insulating oil used. It is because dibenzyl disulfide (DBDS), which is the prime compounds that cause copper sulfide deposition, is consumed by the reaction with copper during operating of transformer. Therefore, it is necessary to detect the existence of DBDS in insulating oil diagnosed as non-corrosivity by IEC 62535. The proceeding paper [6] reports that Bibenzyl (BiBz) and Dibenzyl sulfide (DBS) will be formed in the insulating oil as by-products of copper sulfide formation between copper and DBDS in oxygen-poor atmosphere which imitated the closed-type transformers. These by-products are considered to be the indication of copper sulfide formation. However, the influence of oxygen and addition agent (e.g. 2,6-di-tert-butylp- cresol) on the mechanism of the by-product formation is unclear. The purpose of this study is to elucidate the influence of oxygen and DBPC in by-products formation for development of diagnosis. It became apparent that benzyl alcohol, benzaldehyde and benzoic acid generate as by-products of copper sulfide formation in the air atmosphere which imitated the open-breathing transformers. Furthermore, it became apparent that the reaction product of benzyl radical and the radical of DBPC generates as by-product of copper sulfide formation in the insulating oil containing DBPC. These by-products are detectable even if DBDS disappears. Therefore, it is thought that diagnosis of the open-breathing transformer is possible by detecting these by-products. [ABSTRACT FROM AUTHOR]

A post mortem analysis of scrapped transformers provides an opportunity to directly measure the properties of in-service aged paper insulation. Investigations on 10 scrapped 275 kV and 400 kV power transformers were carried out, where Tensile Index (TI) and Low Molecular Weight Acid (LMA) of the paper insulation sampled from various locations were measured. Multiple-layer TI profile demonstrated the effect of oxidized oil on paper ageing which was confirmed by laboratory ageing experiments. It is LMA rather than High Molecular Weight Acid (HMA) that accelerates the paper degradation. LMA acts as the paper ageing accelerator and also as the paper degradation by-product, supporting the view that self-accelerated hydrolysis process is the main paper ageing mechanism. Finally, a generic relationship between LMA in paper and TI of paper was revealed based on both in-service and laboratory ageing data, i.e. the lower the TI of paper, the higher value of LMA in paper is measured. It implies that LMA in oil can be a potential paper ageing indicator pro viding a link between LMA in oil and paper is found. [ABSTRACT FROM AUTHOR]

The overall reliability of a power transformer depends to a great extent on the sound operation of the bushings thereof. Oil impregnated paper (OIP) insulated bushings have been in use for a long time now. In many situations, it becomes necessary to avoid OIP insulation in bushings. In the recent past, a new technological breakthrough has been achieved whereby the OIP is replaced by epoxy resin impregnated crepe paper (RIP) insulation. This new system has several advantages over OIP and has now become the insulation of choice. However, its long time thermal and electrical performance need to be carefully assessed. This paper reports the results of a study of temperature distribution in the body of insulation, based on the ac conductivity of RIP insulation. A method of computing the maximum thermal voltage of this system is also given. [ABSTRACT FROM AUTHOR]

Results of Frequency Domain Spectroscopy measurements are known to be largely influenced by environmental conditions, such as the temperature. Because field measurements, last hours after de-energizing the transformer, the ambient temperature may affect the results. Especially in cold regions of the world, extreme care are required to interpret the results when performing tests at relatively low surrounding temperatures. A better understanding and analysis of the dielectric test results are therefore only possible with a clear understanding of the physical behavior of the insulation system in response to the ambient conditions. In this contribution, the dielectric behavior of a composite oil paper insulation system has been explained from the properties of Debye basic model. A series of experiments have been performed under controlled laboratory conditions with preset moisture content inside the insulation. The equivalent circuit parameters of a laboratory made oil paper condenser bushing model were obtained using a non-linear optimization procedure. Since the dielectric parameters values are geometry dependent, poles, calculated from resistances and capacitances, were used as they are independent of the geometry. It was shown that the poles can be regarded as parameters able to be used for insulation condition assessment. [ABSTRACT FROM AUTHOR]

The use of paper in electrical insulation, especially in power transformers, remains a topical subject. The interest for the insulating paper, despite the emergence of many synthetic materials is ascribed to its low cost price and its ability to an oil impregnation. However its strong hydrophilic character remains the main difficulty for its implementation in electrical insulation. This affinity to water absorption and/or adsorption shows that a good understanding of the moisture effect becomes imperative. Several studies were carried out on the subject but a systematic study of the moisture effect on overall behavior of paper has not been achieved. This work is meant to be a contribution for this systematic investigation. The first step of this study, which is the object of the present article, concerns an examination of time variation of the electrical currents, under dc stress, for different moisture levels. A particular attention is given to the polarization and depolarization currents. These currents are examined during alternate charges and discharges sequences. An increase of the current, during the application of continuous voltage was noticed. This unexpected phenomenon would be related to an electro-dissociation and/or polarization processes. [ABSTRACT FROM AUTHOR]