Search

Connection of an LC filter to the output of voltage source inverter (VSI) in squirrel cage induction motor (SQIM) drive converts the pulse-width modulated (PWM) voltages into smooth sinusoidal voltages. However, this connection may lead to closed-loop instability in the rotor flux-oriented (RFO) vector-controlled (VC) SQIM system. The closed-loop stability of the combined SQIM + LC filter (SQLC) system is complex and has not been analyzed properly in the literature. In this paper, a detailed closed-loop stability analysis of the SQLC system has been presented based on stability region (SR) and accordingly the PI gains of VC has been designed. The SR method is adopted to derive the common stability regions for the SQIM system and SQLC system. Thereby, the paper proves that connecting an LC filter in-between the VSI and the SQIM system does not always destabilize the closed-loop system. Further, for an SQLC system, the complete range of current controller gains is obtained at various operating points. The frequency-domain specifications have been used to select a proper stabilizing set and the effect of parametric variation of LC filter on the stabilizing set has also been discussed. The experimental results are provided to validate the analysis. [ABSTRACT FROM AUTHOR]

The dc-dc converters with high step-up DC-voltage gain play a vital role in integrating low voltage DC sources. Though several converter topologies are reported in the recent past, attempts have been made to reduce the components, especially the switching devices, passive elements, converter losses, etc., of the converter. A novel DC-DC converter topology, viz., single switched impedance network (SSIN)-based converter with n-stage is proposed in this paper. The operation of the SSIN based converter in continuous and discontinuous conduction modes are discussed. The effect of parasitic elements on DC-voltage gain and efficiency of the SSIN is carried out. The small-signal model of the SSIN converter is derived. The performance of the SSIN converter is compared with the similar converter topologies. The 500 W prototypes of the SSIN with n = 1 and n = 2 are fabricated, and the experimental results are presented in this paper. To improve the converter performance, SiC-based semiconductor devices are used. The SSIN converter with two-stage has low switch loss at 500 W load, improved efficiency during high power and high output voltage operation, the switch stress of Vo/2, etc. [ABSTRACT FROM AUTHOR]

The application of Hall-based BLDC motors ranges from automotive accessory components such as oil and water pumps to high speed compressors. This paper proposes a new twelve-step unsymmetrical 160° commutation strategy using a single Hall-effect sensor method for brushless DC (BLDC) motor drives. The signal from the Hall-effect sensor is used to generate a number of pseudo Hall signals via a proposed speed-position estimator. The pseudo signals are then employed to control switching logic of a voltage source inverter (VSI). The effectiveness of the single Hall sensor method is examined on the unconventional 160° strategy, and on conventional 120°, 150° and 180° strategies with promising results. The paper presents a detailed comparison of the twelve-step unsymmetrical 160° commutation strategy with six-step voltage space vector that is used in conventional 120° and 180° strategies, and twelve-step symmetrical voltage space vector that is used in 150° strategy. Simulation results are validated via experimental measurements on a laboratory set-up using a real time dSPACE control environment, a representative BLDC motor prototype, a VSI and associated control components. [ABSTRACT FROM AUTHOR]

Frequency-domain modeling is an effective technique in the dynamic analysis of power electronic converters-based power systems. In this paper, a unified single-input single-output (SISO) loop gain modeling for the three-phase grid-tied voltage source converters (VSCs) under both symmetric and asymmetric AC grids is presented, which facilitates the physical measurement and stability analysis. Based on the linear-time-periodic (LTP) modeling technique, the harmonic admittance model of the three-phase grid-tied VSC is developed in the stationary (αβ)-frame, which accurately captures the coupling dynamics. This model can be transformed into other existing models through coordinate transformations. According to the idea of mathematical induction, a two-by-two recursive admittance matrix (RAM) model is derived, which is easy to include frequency coupling components of arbitrary order. It is illustrated that the VSC admittance is coupled with the grid admittance due to the frequency coupling effect (FCE). Furthermore, the RAM is converted to its equivalent SISO models following the concept of loop gain. The system stability is thus assessed by the SISO stability criteria (e.g., Nyquist stability criterion). In addition, the loop gain allows the traditional SISO perturbation and measurement scheme to be used for detecting the stability margin information. Finally, simulation results verify the feasibility and correctness of the theoretical analysis presented above. [ABSTRACT FROM AUTHOR]

In this paper, a circulating-current-excited switched reluctance generator system with the diode rectifier is comparatively studied with a field-current-separated switched reluctance generator. By using a DC power source connected in series with the winding to provide the circulating current, a controllable excitation field is established in the proposed generator. To highlight the influence of this DC voltage source, the injected field current of the field-current-separated generator is kept the same as the circulating current of the circulating-current-excited generator. Then, both advantages and disadvantages of the generators are summarized. The circulating-current-excited switched reluctance generator system inherits both the advantages of good reliability of the separated-winding generator by using the diode rectifier and low copper loss of the integrated-winding machine by combining the AC and DC current in one set of windings. Furthermore, two more practically conventional field-current-separated generators are also compared with the proposed generator in terms of the external characteristics. These two conventional generators have different winding configurations. At last, the analysis is verified by experiments. [ABSTRACT FROM AUTHOR]

This paper presents Space Vector Modulation (SVM) sequences that reduce Common Mode Voltage (CMV) in Dual Three-phase Asymmetrical Induction Motor (DTAIM). At first, two existing SVM techniques such as Reference SVM (RSVM) and CMV1 are studied. Additionally, three new switching sequences are developed as CMV2, CMV3 and DCMV3, which reduce peak magnitude of CMV by 66.8% in comparison with RSVM technique. In SVM techniques, to obtain least CMV, zero vectors are usually replaced by two opposite large Active voltage Vectors (AV) with equal time duration. In such topologies like CMV1, total six AVs are utilized to synthesize the reference vector. The proposed SVM technique CMV2 utilizes only five large AVs to synthesize the reference vector and reduces CMV. Selection of five neighbouring AVs is reflected in reduction of harmonic flux trajectories and stator current ripple in proposed techniques. Additionally, two more switching sequences (CMV3 and DCMV3) are developed related to utilization of specific zero voltage vectors in all sectors (7 and 56) that produce zero CMV. These two switching sequences also provide easy implementation feature during the development of c-code program. In this study, CMV and stator current ripple are considered as performance parameters for different SVM techniques. All SVM techniques are analysed by analytical results, computer simulations, and using prototype test setup of DTAIM fed by Dual Three-phase Voltage Source Inverters (DTVSIs). [ABSTRACT FROM AUTHOR]

–This paper proposes an efficient and optimal reduced control set model predictive flux control (RCS-MPFC) for a three-level neutral-point-clamped voltage source inverter (3L-NPC VSI) fed induction motor. The proposed algorithm reduces the computational time in the prediction stage without causing any suboptimality. The optimal voltage vector selected by the proposed method produces the same cost function value as that of the conventional FCS-MPFC which requires enumerating all 27 voltage vectors. Therefore, the proposed algorithm achieves the same performance as the conventional method in the entire range of operation of IM drives while the computational effort is significantly reduced. Experimental results verify the effectiveness of the proposed algorithm and its superior performance compared to the existing RCS-MPFC scheme. [ABSTRACT FROM AUTHOR]

The implementation of finite-control-set model predictive control (FCS-MPC) in voltage source inverters (VSIs) can make the system suffer from poor current harmonics performance, which may complicate the design of the required AC filter. To overcome this shortcoming, a carrier-based modulated model predictive control (CB-MMPC) strategy is proposed in this paper. This method enables the utilization of existing PWM modulation techniques with FCS-MPC, where a modulation waveform with zero-sequence signal injection is generated and compared to a triangular carrier wave, while optimizing the selection of the switching states. As it is shown, the studied CB-MMPC strategy not only considerably improves the current total harmonic distortion (THD) but also attains the performance of fast current dynamic response and robustness as the traditional FCS-MPC. Herein, the detailed implementation of the CB-MMPC control strategy is given, while considering its application to the current feedback control loop of a three-phase three-wire two-level VSI modulated at constant switching frequency. Finally, PLECS circuit simulation and a 3-kW VSI prototype are used to verify the superiority and the effectiveness of the presented CB-MMPC strategy. This is also benchmarked to the FCS-MPC and dead-beat based controllers. [ABSTRACT FROM AUTHOR]

In this paper, an improved magnetic equivalent circuit (MEC) model of a coreless axial-flux permanent-magnet synchronous machine (AFPMSM) with printed circuit board (PCB) winding is presented, which considers the curvature effect, fringing effect, leakage flux, and rotor yoke's magnetic saturation. The axial air-gap flux density distribution, no-load back electromotive force, winding inductances, and electromagnetic torque are predicted by the proposed MEC model. The steady-state performances of the machine under heavy load, as well as the dynamic response of the machine with a connected voltage source and mechanical load, are calculated. All the results obtained from the proposed model are in good agreement with those issued from the 3D finite element method (FEM). The computation time of the proposed model is greatly reduced compared to 3D FEM. Finally, a coreless AFPMSM prototype with a PCB stator is manufactured, and experiments are carried out to verify the predicted results. [ABSTRACT FROM AUTHOR]

The instability issue of the grid-connected Voltage Source Converter (VSC) dominated by phase-lock loop (PLL) is investigated using the electrical torque method in this paper. The system dynamic model and steady-state relationship of variables are first established. Then, a basic two-order model representing the PLL natural oscillation mode is extracted. The impacts of the current control loop and altering current grid (ACG) on the PLL oscillation mode are derived using the electrical torque method. As a result, analytical expressions of the system synchronous and damping coefficients are obtained. Based on the derived synchronous and damping coefficient, qualitative evaluations of the impacts of the system parameters on the oscillation frequency and system stability can be achieved. It is drawn that a small PLL time constant, low infinite source voltage, heavy load, reactive power absorption, and long electrical distance will deteriorate system stability. Moreover, a sufficient analytical stability criterion for the grid-connected VSC is derived from the damping coefficient. The system stability can be directly evaluated through the operation points and system parameters, and the quantitative evaluation of the system stability is achieved. The eigenvalue analysis and electromagnetic transient simulation have verified the reliability and effectiveness of the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dual input nine-level inverter (DINLI) topology which requires only seven controllable devices. The dual inputs are un-identical DC voltage sources in the ratio 1:3. A simple control scheme is derived by appropriately modifying the phase disposition pulse width modulation technique to generate high-quality 9-level output from the DINLI topology. At any given instant, a maximum of four switches conduct out of which only a maximum of two switches operate at high frequency, bringing down the switching and conduction losses significantly and improving the overall system efficiency. The bidirectional DINLI (BDINLI) topology with reactive power capability can be realized by replacing the unidirectional devices with the controlled switches (i.e., total nine switches). In addition, the proposed DINLI topology does not require extra voltage balancing circuits which further improves the efficiency. The DINLI operation is verified through MATLAB simulations for grid-connected applications and its extension to an n-level, 3-phase application is also investigated. Experiments performed on a 1KVA laboratory prototype to validate the theoretical claims. [ABSTRACT FROM AUTHOR]

With widespread application of voltage source converter (VSC) as a key energy-conversion power electronic device by using the phase-locked loop (PLL) technique for synchronization, the system dynamics has become much complicated. In this paper, the nonlinear dynamics and transient stability of the PLL-based VSC system are investigated, within a unified framework of the (normalized) generalized swing equation. It is found that there are three different types of bifurcation, including the generalized saddle-node, Hopf, and homoclinic bifurcations. Within the coexistence parameter region, the basin boundary of the stable equilibrium point shows either a closed-loop or a fish-like pattern. With the help of the equal area criterion (EAC), the transient stabilities under different transient disturbances including short circuit, voltage dip, and power rise are analyzed. Because the equivalent damping of the VSC is state-dependent, the theoretical results based on the EAC are examined. Furthermore, based on the analytical results from the generalized swing equation, the principle for all major transient stability enhancement methods is uncovered. All these findings are well verified by extensive electromagnetic transient simulations. Therefore, the generalized swing equation provides a deeper physical insight and plays a crucial role in transient stability problems in power-electronic-dominated power systems, similar to the swing equation in traditional power systems. [ABSTRACT FROM AUTHOR]

This paper presents a dual-hysteresis band control method for multi-drive systems based on a nine-switch inverter. The drive system contains two independent three-phase induction motors fed by a nine-switch inverter. Independent control of torque, speed, and stator current of two load stages is achieved. The proposed strategy offers a reliable control operation of both induction machines under individual load profiles. Instead of using independent sets of three-phase voltage source converters, the nine-switch inverter is used to drive separate machines. Thus, the volume and size of the power stage are noticeably reduced due to the use of fewer semiconductors. The theoretical concept and design steps of the proposed method are presented. The performance of the closed-loop independent motor control scheme is experimentally validated using a 3.2 kW lab-scaled nine-switch inverter prototype and Altera Cyclone IV Field-programmable gate array. [ABSTRACT FROM AUTHOR]

This paper presents the variable speed applications of a recently developed generator named Brushless Induction Excited Synchronous Generator (BINSYG) for offshore wind power applications. The machine is basically a Synchronous generator (SG) with its excitation fed from a three-phase Induction Machine (IM). Both the machines are embedded in the same machine frame and share the same magnetic core. The SG feeds power to the dc grid via a five-level Unidirectional Dual Flying Capacitor Active Neutral Point Converter. The converter is controlled such that the Total Harmonic Distortion (THD) of the current flowing through the stator of SG is below 5% and at unity power factor at SG terminal. The excitation developed by IM-type exciter is adjusted using a new control strategy that is proposed for Voltage Source Inverter, such that BINSYG can operate at wide speed range necessary for Wind Energy Systems (WES). The complete system is controlled without using ac voltage sensors and speed encoders. The proposed WES with its control algorithm is first modelled in MATLAB/Simulink. Further, rapid control prototyping verification in the form of real-time results using OPAL-RT is presented for a small scale (5.5 kVA) BINSYG feeding power to a 750 V dc grid. [ABSTRACT FROM AUTHOR]

This paper proposed a hybrid subdomain model (HSM) for calculating the magnetic field distribution of interior permanent-magnet (IPM) machine accounting for slotting effect, rotor saliency, and iron nonlinearity. In the constant permeability region, i.e., slots, slot-opening, and air-gap, three subdomains are introduced to represent their magnetic field. By applying the subdomains interface conditions and nonlinear boundary conditions, the analytical air-gap field solution can be obtained based on the governing Laplace and Poisson equation. For the iron region, the magnetic reluctance network (MRN) is proposed to account for rotor saliency iron and nonlinearity. The magnetic voltage source is introduced to represent the permanent-magnet (PM) while the air-gap flux source is used to replace the air-gap reluctance network, which is the key to guarantee the computational efficiency and high accuracy. The electromagnetic performances of both flat-shaped and V-shaped IPM machines are investigated to show the advantages of different IPM machine topologies analytically. The HSM predictions for both IPM machines are validated by finite-element (FE) analysis and experimental results. [ABSTRACT FROM AUTHOR]

In order to better address the problem of many high-order harmonics’ concentration in the output voltage, a novel five-phase piecewise-random-switching-frequency space vector pulse width modulation (PRSF-SVPWM) strategy is proposed for a five-phase voltage source inverter. Compared to the conventional random switching frequency SVPWM (RSF-SVPWM), the entire fundamental period of this method is divided into two half-fundamental periods, so the original switching frequency in a single fundamental period is randomized in segments respectively. During this process, parameters named the offset frequency and random frequency are defined and assigned reasonably. In this way, high-frequency harmonics in one period are spread into a wider range. Subsequent simulation and experimental results verify that the proposed random modulation strategy can further reduce amplitudes of harmonics near switching frequency and its integer multiples, even though within a narrow switching frequency range, and a satisfactory effect of high-order harmonic dispersion is finally obtained, which contributes to the application and popularization of random pulse width modulation strategies. [ABSTRACT FROM AUTHOR]