Search

This paper proposes a novel dual input nine-level inverter (DINLI) topology which requires only seven controllable devices. The dual inputs are un-identical DC voltage sources in the ratio 1:3. A simple control scheme is derived by appropriately modifying the phase disposition pulse width modulation technique to generate high-quality 9-level output from the DINLI topology. At any given instant, a maximum of four switches conduct out of which only a maximum of two switches operate at high frequency, bringing down the switching and conduction losses significantly and improving the overall system efficiency. The bidirectional DINLI (BDINLI) topology with reactive power capability can be realized by replacing the unidirectional devices with the controlled switches (i.e., total nine switches). In addition, the proposed DINLI topology does not require extra voltage balancing circuits which further improves the efficiency. The DINLI operation is verified through MATLAB simulations for grid-connected applications and its extension to an n-level, 3-phase application is also investigated. Experiments performed on a 1KVA laboratory prototype to validate the theoretical claims. [ABSTRACT FROM AUTHOR]

A new transformer-less three-level grid-tied inverter is proposed in this article. By employing the switched-capacitor (SC) modules, a new topology is derived. The proposed topology has some features which are high efficiency, the capability of voltage boosting without utilization of any additional boost stage, and suppressing the leakage current by using common grounded strategy. In this article, a peak current control is employed to generate the gate pulses of power semiconductor switches and adjustment of both active and reactive powers. By doing so, the grid injected current is controlled and adjusted to have a proper quality. The operation modes, design consideration, and a comparison with some recently proposed grid-connected topologies are done through this paper. Finally, the performance and feasibility of the proposed inverter are confirmed with a 500 W experimental prototype. [ABSTRACT FROM AUTHOR]

Hybrid boost converter (HBC) has been proposed to replace a dc/dc boost converter and a dc/ac converter to reduce conversion stages and switching loss. In this paper, control of a three-phase HBC in a Photovoltaic (PV) charging station is designed and tested. This HBC interfaces a PV system, a dc system with a hybrid plug-in electrical vehicles, and a three-phase ac grid. The control of the HBC is designed to realize maximum power point tracking for PV, dc bus voltage regulation, and ac voltage or reactive power regulation. A testbed with power electronics switching details is built in MATLAB/SimPowersystems for validation. Simulation results demonstrate the feasibility of the designed control architecture. Finally, lab experimental testing is conducted to demonstrate HBC's control performance. [ABSTRACT FROM AUTHOR]

In this paper, a multilevel inverter based on three-phase H-bridge inverters for an open-end winding induction motor drive is presented and its fault-tolerance capability is investigated. The multilevel topology is obtained using three wye-connected three-phase H-bridge inverters to supply open-end winding induction motors. This topology has the ability to extend the maximum voltage applied to the motor windings up to two times the dc supply voltage of the three-phase inverters. For a given induction motor voltage, the topology allows the use of dc sources with a lower voltage rating. Consequently, faster power semiconductors can be used. This multilevel topology can be directly controlled by modifying known modulation concepts, such as sinusoidal pulse width modulation (PWM). In this study, two sinusoidal PWM modulation techniques will be implemented: the level-shifted carriers (phase disposition) and the phase-shifted modulator. Fault-tolerant operation under an open-switch fault without adding any extra components and without changing the modulation strategy is also proposed, adding fault-tolerant capability to the new topology. Experimental results of this multilevel inverter in normal operation and in fault tolerant mode are presented. The obtained results confirm the fault effectiveness of the proposed multilevel topology. [ABSTRACT FROM PUBLISHER]

The flying-capacitor-based multilevel converter is one of the well-known breeds of the multilevel power converters. This paper proposes a new flying-capacitor-based multilevel converter to minimize the number of flying capacitors (FCs) and power switches. The advantage of the proposed FC-based multilevel converter in comparison with the conventional flying-capacitor multicell converter is that it needs fewer FCs. Also, in comparison with the stacked multicell converter, the proposed multilevel converter requires fewer semiconductor switches. In order to balance the voltage of the FCs in proposed multilevel converter, a new active voltage balancing method which is fully implemented using logic-form equations is presented. The proposed voltage balancing method measures output current and FC voltages to generate switching states to produce the required output voltage level, as well as balance the FCs voltages at their reference values. The output voltage of the proposed multilevel converter controlled with suggested active voltage balancing method can be modulated with any pulse-width-modulation (PWM) method, such as phase-shifted-carrier PWM or level-shifted-carrier PWM. Simulation results and experimental measurements of proposed FC-based multilevel converter are presented to verify the performance of the proposed converter, and its novel switching and modulation strategy, which is based on the active voltage balancing method. [ABSTRACT FROM PUBLISHER]