Search

Virtual synchronous generator (VSG)-based control approaches for AC machine drivers have attracted much attention in recent years. The contradiction between the strong motor loading capacity and the small DC voltage fluctuation is disregarded in previous studies. A larger virtual inertia is required to raise the torque gain and drive the motor with heavier loads, thus resulting in greater DC voltage variations. A systematic method is proposed for the optimal design of the virtual inertia for VSG-based motor starting systems to achieve the maximal motor loading capacity and the low DC voltage fluctuation in this paper. Firstly, the relationship between the virtual inertia and the loading capacity is revealed on the basis of the closed-loop analysis. Considering the DC voltage variation, the constraint on the maximal value of the virtual inertia is proposed from the energy-balance perspective despite the unknown contribution of the DC capacitors to the virtual inertia. To fully exploit the energy storage capacity of the DC capacitors and raise the upper limit of the virtual inertia under the same permitted DC voltage variation, a modified DC voltage reference is introduced. Extensive simulation and experimental results are presented to validate the effectiveness of the proposed methods. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dual input nine-level inverter (DINLI) topology which requires only seven controllable devices. The dual inputs are un-identical DC voltage sources in the ratio 1:3. A simple control scheme is derived by appropriately modifying the phase disposition pulse width modulation technique to generate high-quality 9-level output from the DINLI topology. At any given instant, a maximum of four switches conduct out of which only a maximum of two switches operate at high frequency, bringing down the switching and conduction losses significantly and improving the overall system efficiency. The bidirectional DINLI (BDINLI) topology with reactive power capability can be realized by replacing the unidirectional devices with the controlled switches (i.e., total nine switches). In addition, the proposed DINLI topology does not require extra voltage balancing circuits which further improves the efficiency. The DINLI operation is verified through MATLAB simulations for grid-connected applications and its extension to an n-level, 3-phase application is also investigated. Experiments performed on a 1KVA laboratory prototype to validate the theoretical claims. [ABSTRACT FROM AUTHOR]

This paper presents a single-objective model predictive control for a bidirectional DC-DC flying capacitor (FC) converter, which integrates a battery to the microgrid. The presence of multiple FCs facilitates the converter to interface a low-voltage battery to a high-voltage DC bus at reduced voltage stress on its power switches. However, such converter requires a controller that fulfils multiple objectives, namely DC bus and FC voltage regulations, and bidirectional power flow. The key feature of the proposed controller is that it utilizes a model predictive control with a single-objective cost function based on battery current and a redundant state selection scheme to attain these multiple objectives. Adopting such a strategy not only reduces computational burden but also eliminates the need for weighting factors and requirement of complex numerical models for its estimation. Another notable aspect is that the controller employs an improved dynamic reference model to generate appropriate battery current reference for the DC bus voltage regulation, without necessitating a secondary control loop and additional current sensors. Finally, experimental results of the proposed system for a step-response of the DC bus voltage, varying PV power, and loads are validated and compared against finite control set model predictive control. [ABSTRACT FROM AUTHOR]

This paper proposes an improved SOC balancing strategy for the modular energy storage system (ESS) based on low bandwidth communication (LBC) technology, aiming at solving the drawbacks of the conventional balancing strategy based on droop control. The proposed control scheme can improve the SOC balancing efficiency and remove the current deviation by using the SOC slope-adjusting and current-shifting approaches simultaneously. The average value of SOC can be derived through the LBC line, and the droop coefficient based on SOC can be controlled in the local control layer. Thus, the SOC of each sub-module can converge to the average SOC value in system dynamic process, and the balancing speed under the condition of low SOC difference between sub-modules can be improved. Furthermore, the current regulation performance in steady and transient states can be enhanced by using the proposed method. At last the effectiveness of the proposed strategy is verified by experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a new single-source three-phase seven-level inverter with an inherent three-time voltage boosting capability for medium-voltage applications. The proposed topology is comprised of series connection of two switched-capacitor (SC) networks with an added half-bridge module per phase. Each of such integrated SC networks requires a single capacitor associated with three active power switches. The three-time voltage boosting feature of the proposed topology can reduce the dc-link voltage requirements by 50% in comparison to the traditional neutral point clamped (NPC), flying capacitors, active NPC (ANPC), hybrid clamped ANPC, and cascaded H-bridge topologies, and 75% to advanced ANPC topologies. It can also reduce the number of required switches and capacitors as well as their voltage stresses compared to those state-of-the-art topologies reported in the literature. By integrating “n” number of added SC networks in the proposed seven-level basic topology, the number of output voltage levels can be extended to 2n+3 per phase. A finite control set model predictive control algorithm is also derived to control the converter in both the active and reactive power exchanges modes without distorting the generated grid current quality. The capacitor voltage balancing is inherent in the proposed topology, and thus, there is no need for any additional voltage balancing circuit, which further reduces the control complexity. The performance of the proposed topology and its control algorithm are validated by several measurement results. [ABSTRACT FROM AUTHOR]

An improved two-stage model predictive current control (MPCC) for three-phase three-level converters in the paper, which can simultaneously achieve common-mode voltage (CMV) reduction, effective dc-link capacitor voltage control, and decreased computational burden, is proposed. Compared to the other current control strategies, it has the capability of handling multiple control objectives and possesses a simple structure. Furthermore, it greatly reduces the CMV since the peak CMVs of all the candidate voltage vectors are constrained to be less than one sixth of the dc-link voltage. In addition, an optimal two-stage voltage vector selection mechanism is employed in the proposed method. It helps to significantly reduce the computational complexity. Simulation and experimental results are provided to verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

Conventionally, the converter of switched reluctance motor (SRM) is fed by the uncontrollable diode bridge rectifier (DBR), which leads to a low grid-side power factor (PF) and high current total harmonic distortion (THD). In this paper, an alternative solution for the grid-connected high-speed SRM drive system with improved PF is proposed. In the proposed drive system, the three-level active front end (AFE) is connected in cascade with the midpoint converter for SRM operation. A centralized strategy, which controls the AFE and SRM together, is proposed to govern the motor speed and grid-side PF by regulating the real power and reactive power of the system, respectively. Specifically, the real power, reactive power, and the voltage balancing of split capacitors are controlled by the model predictive directed power control (MP-DPC) algorithm, which significantly reduces the control complexity and guarantees the fast dynamic response. Consequently, satisfying speed regulation, high PF, low current THD, and bi-directional power-transfer capability are achieved. An idea-proofed testbench is constructed in laboratory, and the applicability of the proposed drive system is verified by a series of experimental results. [ABSTRACT FROM AUTHOR]