Search

This paper presents a simple pulse width modulation algorithm for control of an ultracapacitor based energy storage system used for source and load support applications. As opposed to dual loop control philosophy that is widely used for backup applications, this paper presents a simple single loop current control that is only useful for controlling the ultracapacitor based DC/DC converters used in source and load support applications. The proposed PWM blocking method necessitates the DC/DC converter to operate in five states and takes into consideration the essential operational limits associated with the ultracapacitors. The performance of the proposed algorithm is verified experimentally using a 24 V laboratory prototype setup. Further, the shortcomings of dual loop control when applied to source and load support applications are demonstrated. [ABSTRACT FROM AUTHOR]

The digital implementation of all the control loops of a versatile buck-boost (VBB) dc–dc converter used in a stand-alone photovoltaic application is proposed in this paper to improve existing digital-analog sliding-mode-based implementations. All three control loops: maximum power point tracking (MPPT), fast input voltage regulation, and inner high-bandwidth current control, have been programmed in the same digital signal controller (DSC). A Model Predictive Control (MPC) based algorithm has satisfactorily solved the challenge of implementing the nominal 100 kHz switching frequency current loop. The MPC cost function is distributed throughout the algorithm to achieve three specific goals: the tracking of the reference current (G1), a quasi-constant steady-state switching frequency (G2), and the assurance that the duration of an interval is larger than the time required to calculate it (G3). The third goal requires the current control to toggle between peak- and valley-modes depending on the operating point. The correct fulfillment of these control objectives on the proposed MPC-based algorithm has been validated through simulations and experimental tests performed on a purpose built-prototype. [ABSTRACT FROM AUTHOR]

In this paper, a fault-tolerant control of a symmetrical six-phase induction generator based on a variable structure strategy is experimentally tested and compared with a classical proportional-integral controller. For this, we use a linear feedback sliding mode controller with switched feedback gains in such a way to control the inner current loops of this machine. One main drawback of the classical three-phase induction generator is that it is no longer possible to generate electrical power if only one phase is lost on the stator side. To overcome this issue, we will use a squirrel cage six-phase induction machine that can still operate when at least three phases remain on the stator side. This article proposes to use a variable structure control in order to cope with unbalanced currents and also maintain the generation of power when a loss of the stator's phases occurs. The proposed controller shows its robustness and good regulation performance in healthy and faulty modes. The simulation and experimental tests were carried out with a 24 kW induction machine that represents 1/100 of the electrical power of a real wind turbine. [ABSTRACT FROM AUTHOR]

An improved two-stage model predictive current control (MPCC) for three-phase three-level converters in the paper, which can simultaneously achieve common-mode voltage (CMV) reduction, effective dc-link capacitor voltage control, and decreased computational burden, is proposed. Compared to the other current control strategies, it has the capability of handling multiple control objectives and possesses a simple structure. Furthermore, it greatly reduces the CMV since the peak CMVs of all the candidate voltage vectors are constrained to be less than one sixth of the dc-link voltage. In addition, an optimal two-stage voltage vector selection mechanism is employed in the proposed method. It helps to significantly reduce the computational complexity. Simulation and experimental results are provided to verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

Vibration and acoustic noise are considered as major factors preventing the widespread use of switched reluctance motor (SRM) drives in industrial and commercial applications. In this paper, a new active vibration cancellation strategy for radial vibration is proposed based on the optimal current switching instants. The mechanical impulse response method has been used to estimate the radial vibration of the stator and an optimization routine was developed to define the optimal instants for phase current switching in such a way that the resulting vibration would cancel the vibration caused by prior switching. Experimental verification was conducted on an 8/6 SRM and the results show significant reduction in the stator radial vibration which in turn contributes to reduction of acoustic noise. [ABSTRACT FROM AUTHOR]

This paper proposes a deadbeat finite set model predictive current control based on discrete space vector modulation (DSVM) in order to achieve robust characteristics from the grid impedance variation while guaranteeing high performance of output current waveforms and a fixed switching frequency. The proposed DSVM strategy enables to obtain a large number of virtual voltage vectors without complex initialization process or lookup table, which are the drawbacks of the conventional DSVM strategies. A deadbeat technique was adopted to minimize the number of candidate voltage vectors considered in the cost function in order to avoid the high computational burden caused by considering all voltage vectors. The simulation and experimental results were presented to verify the effectiveness and performance of the proposed method using a two-level grid-connected voltage source inverter. [ABSTRACT FROM AUTHOR]

A fully integrated on-board battery charger for future electric vehicles (EVs) has been recently introduced. It reutilizes all the propulsion components of an EV in charging/vehicle-to-grid (V2G) modes, it does not require any additional components or hardware reconfiguration, and charging/V2G modes are realized with zero electromagnetic torque production. Both fast (three-phase) and slow (single-phase) chargings are possible, with unity power factor operation at the grid side. The solution is based on the use of a triple three-phase machine and a nine-phase inverter/rectifier. This paper reports on the results of efficiency evaluation for the said system. Testing is performed using both a nine-phase induction machine and a nine-phase permanent magnet machine for a range of operating conditions in charging/V2G modes, with both three-phase and single-phase grid connection. Additionally, the impact of converter interleaving on the losses and efficiency is also studied. Losses are separated for different subsystems, thus providing an insight into the importance of optimization of different EV power train components from the efficiency point of view. Promising efficiencies, in the order of 90%, are achieved although none of the system components have been optimized. [ABSTRACT FROM AUTHOR]

In this paper, we introduce an improved ac current controller with robustness against the noise in the feedback path. This three-phase current controller is suited for inverter supplied ac machines and grid-connected power converters. Conventional solutions make use of symmetric pulse-width modulation (PWM) techniques with feedback sampling in the middle of the voltage pulses. Single-sample-based feedback acquisition gets affected by the noise and parasitic phenomena. We perform a thorough analytical and experimental study on feedback errors with conventional sampling, and we consider the impact of the lockout time, motor cables, winding capacitance, and anti-aliasing filters. In order to suppress a significant spectral content in the area of low-order harmonics, we apply an improved acquisition technique, which uses a period-average and removes any PWM noise from the feedback signals. Both anti-aliasing filter and proposed period-average filter introduce delays, which impair the control-loop performance. The conventional current controller is then extended to suppress the effects of the delays. Parameter setting procedure is devised to achieve both the bandwidth and the robustness against the parameter changes. Analytical and experimental studies prove that the proposed feedback acquisition technique improves the robustness in the presence of variable delays and switching transients. Experimental tests show that the extended current controller with period-average feedback acquisition reaches the same bandwidth and robustness as the state-of-the-art controller. [ABSTRACT FROM PUBLISHER]