Search

This paper presents a different Finite Control Set – Model Predictive Control (FCS-MPC) for grid-connected three-phase bidirectional power inverters. These are typically used in dc or ac renewable-based microgrids (MGs), where bidirectional operation and fast dynamic response is required. The bidirectional grid-connected inverters are an essential part of MG, which inject energy into the ac grid or demand energy from it. The dynamic behavior of the system is a major concern since the current can suddenly change depending on the hierarchical controller. This paper proposes a different cost function using sliding mode theory, which offers a good dynamic response, reduced computational burden, and a parameter-free control model. The operation principle of the proposed controller is given and evaluated using a Hardware-In-the-Loop (HIL) system, but also experimentally with a 1kW laboratory prototype. The final results demonstrate the advantages of using this approach in grid-connected three-phase bidirectional power inverters in terms of dynamic response and reduced computational burden, making this solution technically attractive and viable. [ABSTRACT FROM AUTHOR]

The supply-side current of an inverter-fed induction motor (IM) is easily accessible and less affected by noises than the motor stator current. This paper proposes a novel sensorless speed estimation method for an IM using the spectrum of the supply-side current. However, due to the influence of fundamental supply frequency, it is difficult to carry out the speed detection straight from the supply-side current signal. In this paper, an analytic model for characterizing the supply-side current of an inverter-fed IM using the modulation theory and the switching function concept is developed. Then, the Hilbert transform is applied to extract the speed harmonic component from the supply-side current. Finally, an interpolated Goertzel algorithm is put forward to enhance the estimation precision of IM speed. The performance of the proposed sensorless speed estimation method is proved by the speed estimation results obtained from hardware experiments of an IM fed by an inverter under different load conditions. [ABSTRACT FROM AUTHOR]

This paper presents an intelligent-based fault-tolerant system for a solar photovoltaic (PV) inverter. Artificial neural network based controller is used to monitor, detect, and diagnose the faults in solar PV panels, battery, semiconductor switches, and inverters. The cascaded multilevel inverter is connected across the combination of solar PV panel and battery for dc–ac conversion. The major advantage of the proposed topology is that it can deliver power from source to the load even under fault and partial shaded conditions. The paper also reviews on various faults in the solar PV energy conversion process and provides suitable solutions for each circumstance. Simulations are undertaken in MATLAB 2016a/Simulink and experimental investigation is carried out for a 3 kWp solar PV system. The results have proven that the system is capable to deliver power in spite of faulty environments. The comparison and discussion of the results were made to show the effectiveness of the proposed system. [ABSTRACT FROM AUTHOR]

Recent technical advances in control, protection and interconnection of distributed power generation units imply that it is practically viable and economically profitable to keep them as backup generators in isolated operating modes. Therefore, along with the development of islanding detection techniques, seamless operation in transition between islanded and grid connected modes is required and more sophisticated control strategies are needed to recognize the existing working condition and adjust the performance to meet the strict standards of grid interconnection. This paper presents a new adaptive control structure, based on internal model control (IMC), which uses multiple models and an inherent islanding detection method through an optimized switching mechanism to tune the operation of a three-phase inverter under transitions between islanded and grid-tied conditions. By applying a power synchronization method, the system emulates the operation of a synchronous machine which is needless to rely on a phase-locked loop to synchronize during the transitions. Hardware co-simulation environment in Simulink/PLECS and Xilinx System Generator have been utilized to evaluate the transient behavior of the controller in discretized domain and verify its robustness during parameter variations and load switching conditions. Various switching rules have been applied and a comparison of their effect in transient response is demonstrated. The results, taken from several case studies, confirm the significant robustness of the proposed control methodology. [ABSTRACT FROM AUTHOR]

Reliability of power systems can be improved by the use of voltage source inverters (VSIs) with fast dynamic control, which can handle uncertainties induced by renewable energy resources and nonlinear loads. To ensure fast-dynamic response and simplified controller design, various model predictive control (MPC) methods are investigated in this paper. In the conventional MPC design for three-level VSIs, the cost function requires an additional term to ensure the balance of the neutral-point voltage (NP-V), which however can considerably impact the main goal of the MPC. To address this issue, an enhanced MPC using virtual space vectors is proposed, which allows the use of a significantly reduced weighting factor for the term in the cost function for NP-V balancing, while retaining fast-dynamic response. Additionally, the proposed MPC leads to reduced harmonic distortion in the VSI output voltage and current. Both simulation and controller hardware-in-the-loop studies are performed to demonstrate the effectiveness of the proposed enhanced MPC in an operating microgrid under both steady-state and fast-transient conditions. [ABSTRACT FROM AUTHOR]

There is increasing interest in the use of transformer-less systems for grid-connected photovoltaic applications. Compared to transformer-coupled solutions, transformer-less systems offer a typical efficiency increase of 1–2%, reduced system size and weight, and a reduction in cost. However, the removal of the transformer has technical implications. In addition to the loss of galvanic isolation, dc current injection into the grid is a potential risk. While desirable, complete mitigation of dc current injection via convention current control methods is known to be particularly challenging. For this reason, this paper proposes an active dc suppression method, in which the dc current injection is accurately determined by extracting the line-frequency component from inverter dc-link current measurements, and then, mitigated with an active closed-loop controller. Experimental results from a laboratory grid-connected inverter system are presented to demonstrate the high performance of the proposed technique. [ABSTRACT FROM AUTHOR]

An isolated single sourced multi-output dc/dc converter with a high-frequency link was proposed before to feed different cells of the Asymmetrical Cascaded H-bridge (ACHB) inverter. One of the fundamental advantages of the ACHB is that the main H-bridge is commutated with fundamental frequency, passing the majority of the inverter power. However, the isolated dc/dc converter needs to be connected to the main voltage source with high-voltage/high-frequency switches, which limits the power capability and the efficiency of the converter. In this paper, a switching pattern based on nearest level modulation method is proposed to command all the power to be transferred through the main H-bridge. Therefore, the power circulates between the auxiliary H-bridges with no need for high-voltage switches. As a result, a single-input single-output auxiliary converter is needed with only 5% of the power rating. This solution reduces cost and size while it improves the efficiency of the converter. Furthermore, the architecture makes the inverter more suitable for high power and high-voltage applications. The inverter switching strategy is based on programmable firing angles. The main dc-link of the grid connected inverter is controlled to achieve maximum power point tracking, while the dc/dc isolated converter is controlled to regulate the auxiliary dc-links. The proposed topology is verified by simulation and experimental results using a 1.5 kW hardware prototype. [ABSTRACT FROM AUTHOR]

This paper proposes a new diode-clamped multilevel inverter that can effectively balance the voltages of dc capacitors. For the proposed inverter, the inductors are inserted between the diodes and the main switches. Also, the voltage balance of the dc capacitors can be guaranteed by controlling the opening time of the corresponding main switches in particular modes. Thus, the parallel circuits on the dc side in the conventional inverters are canceled. Consequently, the proposed topology requires fewer switches, diodes, and capacitors, although it adds the compensation currents to the corresponding main switches. Both the simulation and experimental results demonstrate the suitability and applicability of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper proposes a deadbeat finite set model predictive current control based on discrete space vector modulation (DSVM) in order to achieve robust characteristics from the grid impedance variation while guaranteeing high performance of output current waveforms and a fixed switching frequency. The proposed DSVM strategy enables to obtain a large number of virtual voltage vectors without complex initialization process or lookup table, which are the drawbacks of the conventional DSVM strategies. A deadbeat technique was adopted to minimize the number of candidate voltage vectors considered in the cost function in order to avoid the high computational burden caused by considering all voltage vectors. The simulation and experimental results were presented to verify the effectiveness and performance of the proposed method using a two-level grid-connected voltage source inverter. [ABSTRACT FROM AUTHOR]

In this paper, a new topology of two-stage cascaded switched-diode (CSD) multilevel inverter is proposed for medium-voltage renewable energy integration. First, it aims to reduce the number of switches along with its gate drivers. Thus, the installation space and cost of a multilevel inverter are reduced. The spike removal switch added in the first stage of the inverter provides a flowing path for the reverse load current, and as a result, high voltage spikes occurring at the base of the stepped output voltage based upon conventional CSD multilevel inverter topologies are removed. Moreover, to resolve the problems related to dc source fluctuations of multilevel inverter used for renewable energy integration, the clock phase-shifting (CPS) one-cycle control (OCC) is developed to control the two-stage CSD multilevel inverter. By shifting the clock pulse phase of every cascaded unit, the staircase-like output voltage waveforms are obtained and a strong suppression ability against fluctuations in dc sources is achieved. Simulation and experimental results are discussed to verify the feasibility and performances of the two-stage CSD multilevel inverter controlled by the CPS OCC method. [ABSTRACT FROM AUTHOR]

This paper proposes a generalized direct torque control (DTC) strategy for multilevel inverter fed DTC (MLI-DTC) drives. By using a simple voltage vector decomposition technique, the proposed method is compatible with inverters possessing any number of voltage levels. Consequently, voltage vectors are applied in a similar way as in the case of a two-level inverter fed DTC. A constant inverter switching frequency is imposed in the proposed method by using a torque regulator in place of the traditional torque hysteresis controller, which enables the application of two voltage vectors within one switching cycle. This also contributes to reduce the torque and flux ripples. Detailed design guidelines for the proposed torque regulator are provided. Experimental results obtained with a three-level neutral point clamped inverter show that the proposed MLI-DTC drive operates with low, constant switching frequency while alleviating torque and flux ripples under all operating conditions. Comparative study with a prior art and parametric sensitivity analysis are also presented to verify the effectiveness and robustness of the proposed MLI-DTC method. [ABSTRACT FROM PUBLISHER]

As penetration of distributed generation increases, the electrical distribution networks may encounter several challenges mainly related to voltage control. The situation may deteriorate in case of a weak grid connected to an intermittent source such as photovoltaic (PV) generation. Fast varying solar irradiance can cause unacceptable voltage variations that may not be easily compensated by slow-responding utility equipment. The PV inverter can be used to control the grid voltage by injecting/absorbing reactive power. A small-signal model is derived in order to study the stability of a PV inverter exchanging reactive power with the grid. This paper also proposes a method that utilizes the available capacity of the PV inverter to support the grid voltage without violating the rating of the inverter and the maximum voltage that the inverter's switching device can withstand. The method proposed in this paper is validated using PSCAD/EMTDC simulations. [ABSTRACT FROM PUBLISHER]

For power conversion systems interfaced to four-wire supplies, four-leg converters have become a standard solution. A four-leg converter allows good compensation of zero-sequence harmonics and full utilisation of the dc-link voltage. These are very important features when unbalanced and/or nonlinear loads are connected to the system. This paper proposes a three-dimensional space vector modulation (SVM) algorithm and provides a comprehensive analysis of the algorithm implemented on a three-level, four-leg neutral-point-clamped converter. The algorithm allows a simple definition of the different switching patterns and enables balancing of the dc-link capacitor voltages using the redundancies of the converter states. A resonant controller is selected as the control strategy to validate the proposed SVM algorithm in a 6 kW experimental rig. [ABSTRACT FROM AUTHOR]

In this paper, a wind energy conversion system interfaced to the grid using a dual inverter is proposed. One of the two inverters in the dual inverter is connected to the rectified output of the wind generator while the other is directly connected to a battery energy storage system (BESS). This approach eliminates the need for an additional dc–dc converter and thus reduces power losses, cost, and complexity. The main issue with this scheme is uncorrelated dynamic changes in dc-link voltages that results in unevenly distributed space vectors. A detailed analysis on the effects of these variations is presented in this paper. Furthermore, a modified modulation technique is proposed to produce undistorted currents even in the presence of unevenly distributed and dynamically changing space vectors. An analysis on the battery charging/discharging process and maximum power point tracking of the wind turbine generator is also presented. Simulation and experimental results are presented to verify the efficacy of the proposed modulation technique and battery charging/discharging process. [ABSTRACT FROM AUTHOR]

In this paper, we introduce an improved ac current controller with robustness against the noise in the feedback path. This three-phase current controller is suited for inverter supplied ac machines and grid-connected power converters. Conventional solutions make use of symmetric pulse-width modulation (PWM) techniques with feedback sampling in the middle of the voltage pulses. Single-sample-based feedback acquisition gets affected by the noise and parasitic phenomena. We perform a thorough analytical and experimental study on feedback errors with conventional sampling, and we consider the impact of the lockout time, motor cables, winding capacitance, and anti-aliasing filters. In order to suppress a significant spectral content in the area of low-order harmonics, we apply an improved acquisition technique, which uses a period-average and removes any PWM noise from the feedback signals. Both anti-aliasing filter and proposed period-average filter introduce delays, which impair the control-loop performance. The conventional current controller is then extended to suppress the effects of the delays. Parameter setting procedure is devised to achieve both the bandwidth and the robustness against the parameter changes. Analytical and experimental studies prove that the proposed feedback acquisition technique improves the robustness in the presence of variable delays and switching transients. Experimental tests show that the extended current controller with period-average feedback acquisition reaches the same bandwidth and robustness as the state-of-the-art controller. [ABSTRACT FROM PUBLISHER]

In this paper, we present virtual prototyping of the distributed control for a modular multilevel inverter used as a grid-tie interface for photovoltaics. Due to the distributed control and inherent redundancy in the system composed of many panels and inverter modules, the system topology exhibits fault-tolerance capabilities that we study through virtual prototyping. The fault-tolerance is enabled by several distributed algorithms, such as services to identify which, if any, agents controlling inverter modules have failed. A distributed identifier algorithm allows the system to keep track of the number of operating panels to appropriately regulate the dc voltage output of the panels using buck–boost converters and determine appropriate switching times for H-bridges in the grid-tie. We evaluate the distributed inverter, its control strategy, and fault-tolerance through thousands of simulation scenarios in Mathworks Simulink/Stateflow. Our virtual prototyping framework allows for generating multilevel inverters composed of many inverter modules, and we evaluate inverters composed of five to dozens of inverter modules. Our analysis suggests the achievable total harmonic distortion of the modular multilevel inverter may allow for operating solar arrays in spite of failures of the power electronics, control software, and other subcomponents. [ABSTRACT FROM AUTHOR]

This paper proposes a new modulation strategy that balances the neutral-point voltage for three-level neutral-clamped inverter systems. The proposed modulation replaces the P-type or N-type small switching states with other switching states that do not affect the neutral-point voltage. The zero and medium switching states are employed to help the neutral-point voltage balancing. This method little bit increases the switching events and output total harmonic distortion. However, this method has a strong balancing ability at all regions. Further, it is very simple to implement in both space vector modulation and carrier-based PWM methods. Simulation and experimental results verify the validity and feasibility of the proposed new modulation strategy [ABSTRACT FROM AUTHOR]