Search

Light-emitting diodes (LEDs) are widely used in street lighting, landscape lighting, liquid crystal display (LCD) backlighting, healthcare, etc. As an important part of LED lighting products, LED driver plays a vital role in maintenance costs reduction, energy saving and lifetime prolongation. In this paper, a single-stage LED driver is proposed, which is integrated by a totem-pole bridgeless power factor correction (PFC) unit and several modular LCL-T resonant rectifiers. The totem-pole bridgeless PFC unit and the LCL-T resonant rectifiers are integrated by sharing switches, which can simplify the circuit and reduce the system cost. The output current can be regulated by applying the variable inductor control. Constant duty cycle and fixed switching frequency operation can be achieved as well. The operating principle and the performance of the proposed converter are analyzed in this paper. In addition, a precise parameter design method is proposed by considering the high-order harmonics. At last, an experimental prototype is established to validate the proposed parameter design and variable inductor control method. [ABSTRACT FROM AUTHOR]

This paper presents a simple pulse width modulation algorithm for control of an ultracapacitor based energy storage system used for source and load support applications. As opposed to dual loop control philosophy that is widely used for backup applications, this paper presents a simple single loop current control that is only useful for controlling the ultracapacitor based DC/DC converters used in source and load support applications. The proposed PWM blocking method necessitates the DC/DC converter to operate in five states and takes into consideration the essential operational limits associated with the ultracapacitors. The performance of the proposed algorithm is verified experimentally using a 24 V laboratory prototype setup. Further, the shortcomings of dual loop control when applied to source and load support applications are demonstrated. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dual input nine-level inverter (DINLI) topology which requires only seven controllable devices. The dual inputs are un-identical DC voltage sources in the ratio 1:3. A simple control scheme is derived by appropriately modifying the phase disposition pulse width modulation technique to generate high-quality 9-level output from the DINLI topology. At any given instant, a maximum of four switches conduct out of which only a maximum of two switches operate at high frequency, bringing down the switching and conduction losses significantly and improving the overall system efficiency. The bidirectional DINLI (BDINLI) topology with reactive power capability can be realized by replacing the unidirectional devices with the controlled switches (i.e., total nine switches). In addition, the proposed DINLI topology does not require extra voltage balancing circuits which further improves the efficiency. The DINLI operation is verified through MATLAB simulations for grid-connected applications and its extension to an n-level, 3-phase application is also investigated. Experiments performed on a 1KVA laboratory prototype to validate the theoretical claims. [ABSTRACT FROM AUTHOR]

The supply-side current of an inverter-fed induction motor (IM) is easily accessible and less affected by noises than the motor stator current. This paper proposes a novel sensorless speed estimation method for an IM using the spectrum of the supply-side current. However, due to the influence of fundamental supply frequency, it is difficult to carry out the speed detection straight from the supply-side current signal. In this paper, an analytic model for characterizing the supply-side current of an inverter-fed IM using the modulation theory and the switching function concept is developed. Then, the Hilbert transform is applied to extract the speed harmonic component from the supply-side current. Finally, an interpolated Goertzel algorithm is put forward to enhance the estimation precision of IM speed. The performance of the proposed sensorless speed estimation method is proved by the speed estimation results obtained from hardware experiments of an IM fed by an inverter under different load conditions. [ABSTRACT FROM AUTHOR]

An improved two-stage model predictive current control (MPCC) for three-phase three-level converters in the paper, which can simultaneously achieve common-mode voltage (CMV) reduction, effective dc-link capacitor voltage control, and decreased computational burden, is proposed. Compared to the other current control strategies, it has the capability of handling multiple control objectives and possesses a simple structure. Furthermore, it greatly reduces the CMV since the peak CMVs of all the candidate voltage vectors are constrained to be less than one sixth of the dc-link voltage. In addition, an optimal two-stage voltage vector selection mechanism is employed in the proposed method. It helps to significantly reduce the computational complexity. Simulation and experimental results are provided to verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents Space Vector Modulation (SVM) sequences that reduce Common Mode Voltage (CMV) in Dual Three-phase Asymmetrical Induction Motor (DTAIM). At first, two existing SVM techniques such as Reference SVM (RSVM) and CMV1 are studied. Additionally, three new switching sequences are developed as CMV2, CMV3 and DCMV3, which reduce peak magnitude of CMV by 66.8% in comparison with RSVM technique. In SVM techniques, to obtain least CMV, zero vectors are usually replaced by two opposite large Active voltage Vectors (AV) with equal time duration. In such topologies like CMV1, total six AVs are utilized to synthesize the reference vector. The proposed SVM technique CMV2 utilizes only five large AVs to synthesize the reference vector and reduces CMV. Selection of five neighbouring AVs is reflected in reduction of harmonic flux trajectories and stator current ripple in proposed techniques. Additionally, two more switching sequences (CMV3 and DCMV3) are developed related to utilization of specific zero voltage vectors in all sectors (7 and 56) that produce zero CMV. These two switching sequences also provide easy implementation feature during the development of c-code program. In this study, CMV and stator current ripple are considered as performance parameters for different SVM techniques. All SVM techniques are analysed by analytical results, computer simulations, and using prototype test setup of DTAIM fed by Dual Three-phase Voltage Source Inverters (DTVSIs). [ABSTRACT FROM AUTHOR]

The implementation of finite-control-set model predictive control (FCS-MPC) in voltage source inverters (VSIs) can make the system suffer from poor current harmonics performance, which may complicate the design of the required AC filter. To overcome this shortcoming, a carrier-based modulated model predictive control (CB-MMPC) strategy is proposed in this paper. This method enables the utilization of existing PWM modulation techniques with FCS-MPC, where a modulation waveform with zero-sequence signal injection is generated and compared to a triangular carrier wave, while optimizing the selection of the switching states. As it is shown, the studied CB-MMPC strategy not only considerably improves the current total harmonic distortion (THD) but also attains the performance of fast current dynamic response and robustness as the traditional FCS-MPC. Herein, the detailed implementation of the CB-MMPC control strategy is given, while considering its application to the current feedback control loop of a three-phase three-wire two-level VSI modulated at constant switching frequency. Finally, PLECS circuit simulation and a 3-kW VSI prototype are used to verify the superiority and the effectiveness of the presented CB-MMPC strategy. This is also benchmarked to the FCS-MPC and dead-beat based controllers. [ABSTRACT FROM AUTHOR]

This paper presents an intelligent-based fault-tolerant system for a solar photovoltaic (PV) inverter. Artificial neural network based controller is used to monitor, detect, and diagnose the faults in solar PV panels, battery, semiconductor switches, and inverters. The cascaded multilevel inverter is connected across the combination of solar PV panel and battery for dc–ac conversion. The major advantage of the proposed topology is that it can deliver power from source to the load even under fault and partial shaded conditions. The paper also reviews on various faults in the solar PV energy conversion process and provides suitable solutions for each circumstance. Simulations are undertaken in MATLAB 2016a/Simulink and experimental investigation is carried out for a 3 kWp solar PV system. The results have proven that the system is capable to deliver power in spite of faulty environments. The comparison and discussion of the results were made to show the effectiveness of the proposed system. [ABSTRACT FROM AUTHOR]

The hard switching operation of the insulated gate bipolar transistor (IGBT)-based multilevel converters (MLCs) in the transformer less direct integration of renewable power plants produces a considerable amount of switching and conduction power loss. This eventually causes higher junction temperature and lower thermal stability. The symmetrically designed MLC using third harmonic sixty-degree bus-clamped pulse width modulation (BCPWM) technique demonstrates reduced switching losses and better harmonic spectra. However, the development of analytical power loss model is a complex and challenging issue due to the discontinuous switching mode of IGBTs for the BCPWM in MLC. In this regard, an analytical model for calculating the average and the rms currents for the hard switching operation of IGBTs and antiparallel diodes (APDs) with BCPWM is proposed. Furthermore, to calculate the device turn-on and turn-off losses, a discrete form of equation is presented to evaluate the transition times of switching more precisely. The numerical power loss values of IGBTs and APDs found from the derived analytical equations for MLC are compared with the simulation and experimental results. The numerical results agree well with the simulated and the experimental outcomes, which validate the proposed analytical loss model. Moreover, an advanced three dimensional thermal impedance model with chip-wise interdependent multilayer thermal coupling effect is also considered in this paper to realize the critical thermal loading condition of the switching devices. [ABSTRACT FROM AUTHOR]

Stand-alone microhydro systems based on the self-exited induction generator (SEIG) are popular in developing countries. However, an electronic based controller is required to maintain the quality (voltage and frequency) of the generated power within an acceptable range. Conventionally, this controller is designed using a phase-controlled thyristor circuit (or more recently using a dc chopper circuit) and a fixed resistance dump load to receive the excess generated power. Generally, in small communities the total dissipated power in the dump load is greater than the consumed power by all the households. This problem of inefficient power usage can be solved by distributing the controller among households. The objective of this paper is to improve the distributed electronic load controller (DELC). As with the original DELC, the proposed improved DELC is used for two purposes: First, consuming the excess generated power individually by each household; and second, operating as a complementary device for voltage and frequency regulation of the SEIG. The detailed design and experimental verifications of the proposed improved DELC including the design of an appropriate input filter to minimize the network current distortion are presented here. Additionally, MATLAB simulations are used to study the interaction between the proposed improved DELC and the powerhouse controller (the ELC). [ABSTRACT FROM AUTHOR]

This paper presents an elaborate scheme, which is different from the traditional parameter identification method, to estimate the parameters precisely for high-speed magnetic suspension motor. It is well known that the inductance and resistance of each winding play an important role in ensuring the stability of the controller for motor. There have been sufficient research works on equivalent circuit model, where the input and output data are assumed to be true value, and unknown circuit parameters are obtained by solving the equivalent circuit equations of motor. However, the output data are often interfered with noises, such as measurement error, the high-frequency components from pulse width modulation signals and sampling errors. The system response output data are reconstructed through applying in stochastic theory, which is different from the traditional filter techniques, to eliminate effectively the above-mentioned noises. Thus, the parameters can be estimated precisely. As an experimental verification, parameters estimated by the proposed method are applied in calculation of switching point between pulse width modulation mode and pulse amplitude modulation mode for magnetic suspension motor. The experimental results validate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

The flying-capacitor-based multilevel converter is one of the well-known breeds of the multilevel power converters. This paper proposes a new flying-capacitor-based multilevel converter to minimize the number of flying capacitors (FCs) and power switches. The advantage of the proposed FC-based multilevel converter in comparison with the conventional flying-capacitor multicell converter is that it needs fewer FCs. Also, in comparison with the stacked multicell converter, the proposed multilevel converter requires fewer semiconductor switches. In order to balance the voltage of the FCs in proposed multilevel converter, a new active voltage balancing method which is fully implemented using logic-form equations is presented. The proposed voltage balancing method measures output current and FC voltages to generate switching states to produce the required output voltage level, as well as balance the FCs voltages at their reference values. The output voltage of the proposed multilevel converter controlled with suggested active voltage balancing method can be modulated with any pulse-width-modulation (PWM) method, such as phase-shifted-carrier PWM or level-shifted-carrier PWM. Simulation results and experimental measurements of proposed FC-based multilevel converter are presented to verify the performance of the proposed converter, and its novel switching and modulation strategy, which is based on the active voltage balancing method. [ABSTRACT FROM PUBLISHER]

In this paper, we introduce an improved ac current controller with robustness against the noise in the feedback path. This three-phase current controller is suited for inverter supplied ac machines and grid-connected power converters. Conventional solutions make use of symmetric pulse-width modulation (PWM) techniques with feedback sampling in the middle of the voltage pulses. Single-sample-based feedback acquisition gets affected by the noise and parasitic phenomena. We perform a thorough analytical and experimental study on feedback errors with conventional sampling, and we consider the impact of the lockout time, motor cables, winding capacitance, and anti-aliasing filters. In order to suppress a significant spectral content in the area of low-order harmonics, we apply an improved acquisition technique, which uses a period-average and removes any PWM noise from the feedback signals. Both anti-aliasing filter and proposed period-average filter introduce delays, which impair the control-loop performance. The conventional current controller is then extended to suppress the effects of the delays. Parameter setting procedure is devised to achieve both the bandwidth and the robustness against the parameter changes. Analytical and experimental studies prove that the proposed feedback acquisition technique improves the robustness in the presence of variable delays and switching transients. Experimental tests show that the extended current controller with period-average feedback acquisition reaches the same bandwidth and robustness as the state-of-the-art controller. [ABSTRACT FROM PUBLISHER]

This paper presents the development of a wind switched-reluctance generator (SRG) with interleaved interface dc–dc converter. First, the power circuit and control scheme of the SRG are properly designed. The hysteresis current-controlled pulse width modulation (PWM) scheme is designed to achieve good winding current tracking control, and the robust voltage control scheme is developed to yield well-regulated dc output voltage under varying prime mover driving speed and load conditions. Moreover, the voltage regulation and the developed power performances of SRG are further enhanced using the proposed commutation shift approach. Next, an interleaved current-fed push–pull interface dc–dc converter with two modules is developed to establish the boosted common dc bus voltage of a dc microgrid from the SRG output having fault-tolerant capability. The rating analysis and circuit component design are conducted in detail. Similarly, well-regulated voltage with lower ripples is also yielded via the properly designed schematic and control scheme. [ABSTRACT FROM AUTHOR]

The doubly fed induction generator (DFIG) equipped with self-commutated insulated gate bipolar transistor (IGBT) voltage source converter (VSC) is one of the most popular topologies used in wind power systems. It has the ability to control active and reactive power independently. The reactive power capability is subject to several limitations which change with the operating point. Around synchronous operating point, a special attention is needed since the limitation of maximum junction temperature of the IGBTs cause a reduction on maximum permissible output current at the rotor side. This paper investigates the thermal behavior of the converter using semiconductor losses and thermal model based on the IGBT manufacturer datasheet. Different pulse-width modulation (PWM) types, including continuous and discontinuous types are applied and the results of reactive power capability are compared. Simulation results show that appropriate selection of PWM type is necessary at around synchronous speed to increase the maximum permissible rotor current as well as reactive power capability. [ABSTRACT FROM AUTHOR]