Search

Grid-connected photovoltaic (PV) systems are currently developed by merging a PV array and a DC/AC inverter which are designed separately, without considering the impact of the PV array operational characteristics on the power losses of the DC/AC inverter. In this paper, a co-design technique is presented, where the optimal design parameters of the PV array and DC/AC inverter in a grid-connected PV system are calculated concurrently through a unified design process. The proposed technique enables to optimally match the PV array configuration and the DC/AC inverter structure. A study has been performed, where the PV systems synthesized by applying the proposed co-design technique are compared with the PV system configurations comprising PV arrays and DC/AC inverters that have been designed separately, through distinct optimization processes based on various alternative optimization objectives. The design results for two installation sites, with different meteorological conditions during a year, demonstrated that only the proposed co-design optimization technique is capable of ensuring the maximization of the annual energy production of the overall grid-connected PV system. [ABSTRACT FROM AUTHOR]

There is increasing interest in the use of transformer-less systems for grid-connected photovoltaic applications. Compared to transformer-coupled solutions, transformer-less systems offer a typical efficiency increase of 1–2%, reduced system size and weight, and a reduction in cost. However, the removal of the transformer has technical implications. In addition to the loss of galvanic isolation, dc current injection into the grid is a potential risk. While desirable, complete mitigation of dc current injection via convention current control methods is known to be particularly challenging. For this reason, this paper proposes an active dc suppression method, in which the dc current injection is accurately determined by extracting the line-frequency component from inverter dc-link current measurements, and then, mitigated with an active closed-loop controller. Experimental results from a laboratory grid-connected inverter system are presented to demonstrate the high performance of the proposed technique. [ABSTRACT FROM AUTHOR]

An isolated single sourced multi-output dc/dc converter with a high-frequency link was proposed before to feed different cells of the Asymmetrical Cascaded H-bridge (ACHB) inverter. One of the fundamental advantages of the ACHB is that the main H-bridge is commutated with fundamental frequency, passing the majority of the inverter power. However, the isolated dc/dc converter needs to be connected to the main voltage source with high-voltage/high-frequency switches, which limits the power capability and the efficiency of the converter. In this paper, a switching pattern based on nearest level modulation method is proposed to command all the power to be transferred through the main H-bridge. Therefore, the power circulates between the auxiliary H-bridges with no need for high-voltage switches. As a result, a single-input single-output auxiliary converter is needed with only 5% of the power rating. This solution reduces cost and size while it improves the efficiency of the converter. Furthermore, the architecture makes the inverter more suitable for high power and high-voltage applications. The inverter switching strategy is based on programmable firing angles. The main dc-link of the grid connected inverter is controlled to achieve maximum power point tracking, while the dc/dc isolated converter is controlled to regulate the auxiliary dc-links. The proposed topology is verified by simulation and experimental results using a 1.5 kW hardware prototype. [ABSTRACT FROM AUTHOR]

This paper presents system architecture and control scheme of a photovoltaic (PV) string inverter allowing seamless battery integration with the dc-series integration method. The architecture uses the partial-power processing universal dc–dc optimizer to have flexible power control by regulating the T-node compensation current. The universal optimizer is configured with a dual active bridge dc–dc converter allowing bidirectional power flow and galvanic isolation. Three operation modes are proposed depending on the input sources connected. Based on the operation mode, the universal optimizer and a dc–ac inverter switch their control reference to deliver the maximum PV power and perform battery current control. The steady-state and transient operation of the closed-loop control scheme have been demonstrated through controller hardware-in-the-loop tests to verify feasibility and effectiveness of the PV-battery series inverter architecture. [ABSTRACT FROM AUTHOR]

This paper proposes a new diode-clamped multilevel inverter that can effectively balance the voltages of dc capacitors. For the proposed inverter, the inductors are inserted between the diodes and the main switches. Also, the voltage balance of the dc capacitors can be guaranteed by controlling the opening time of the corresponding main switches in particular modes. Thus, the parallel circuits on the dc side in the conventional inverters are canceled. Consequently, the proposed topology requires fewer switches, diodes, and capacitors, although it adds the compensation currents to the corresponding main switches. Both the simulation and experimental results demonstrate the suitability and applicability of the proposed topology. [ABSTRACT FROM AUTHOR]

In this paper, a combined reactive power modulation and grid current distortion improvement approach is proposed for an H6 transformer-less full-bridge single-phase photovoltaic (PV) grid-connected inverter. H6 transformer-less inverters with traditional modulation and control strategies may not satisfy the requirement of reactive power compensation or may result in more severe zero-crossing current distortion. Therefore, contrary to the traditional modulation, a novel reactive power injection space vector pulse width modulation (SVPWM) is proposed, which consists of two operation stages—inverter modulation and reactive power modulation. The implementation of SVPWM for reactive power modulation using a digital signal processor is also investigated. Furthermore, to suppress the current zero-crossing distortion in the reactive power injection mode, a global sliding mode function based on the proportion-integration-resonance current controller is designed, and the control law of the global sliding mode is derived. Using the segment modulation and grid current distortion improvement approach, the function of reactive current injection is implemented in commercial PV inverters, and the total harmonic distortion of the grid current is decreased significantly by more than 5% in the low-power segment, under the operating conditions of a lagging or leading power factor of 0.95. The effectiveness and feasibility of the proposed approach are verified through simulation and experiment using a 5-kVA prototype. [ABSTRACT FROM AUTHOR]

In this paper, a new topology of two-stage cascaded switched-diode (CSD) multilevel inverter is proposed for medium-voltage renewable energy integration. First, it aims to reduce the number of switches along with its gate drivers. Thus, the installation space and cost of a multilevel inverter are reduced. The spike removal switch added in the first stage of the inverter provides a flowing path for the reverse load current, and as a result, high voltage spikes occurring at the base of the stepped output voltage based upon conventional CSD multilevel inverter topologies are removed. Moreover, to resolve the problems related to dc source fluctuations of multilevel inverter used for renewable energy integration, the clock phase-shifting (CPS) one-cycle control (OCC) is developed to control the two-stage CSD multilevel inverter. By shifting the clock pulse phase of every cascaded unit, the staircase-like output voltage waveforms are obtained and a strong suppression ability against fluctuations in dc sources is achieved. Simulation and experimental results are discussed to verify the feasibility and performances of the two-stage CSD multilevel inverter controlled by the CPS OCC method. [ABSTRACT FROM AUTHOR]

In this paper, a multilevel inverter based on three-phase H-bridge inverters for an open-end winding induction motor drive is presented and its fault-tolerance capability is investigated. The multilevel topology is obtained using three wye-connected three-phase H-bridge inverters to supply open-end winding induction motors. This topology has the ability to extend the maximum voltage applied to the motor windings up to two times the dc supply voltage of the three-phase inverters. For a given induction motor voltage, the topology allows the use of dc sources with a lower voltage rating. Consequently, faster power semiconductors can be used. This multilevel topology can be directly controlled by modifying known modulation concepts, such as sinusoidal pulse width modulation (PWM). In this study, two sinusoidal PWM modulation techniques will be implemented: the level-shifted carriers (phase disposition) and the phase-shifted modulator. Fault-tolerant operation under an open-switch fault without adding any extra components and without changing the modulation strategy is also proposed, adding fault-tolerant capability to the new topology. Experimental results of this multilevel inverter in normal operation and in fault tolerant mode are presented. The obtained results confirm the fault effectiveness of the proposed multilevel topology. [ABSTRACT FROM PUBLISHER]

In this paper, a novel configuration of a three-level neutral-point-clamped (NPC) inverter that can integrate solar photovoltaic (PV) with battery storage in a grid-connected system is proposed. The strength of the proposed topology lies in a novel, extended unbalance three-level vector modulation technique that can generate the correct ac voltage under unbalanced dc voltage conditions. This paper presents the design philosophy of the proposed configuration and the theoretical framework of the proposed modulation technique. A new control algorithm for the proposed system is also presented in order to control the power delivery between the solar PV, battery, and grid, which simultaneously provides maximum power point tracking (MPPT) operation for the solar PV. The effectiveness of the proposed methodology is investigated by the simulation of several scenarios, including battery charging and discharging with different levels of solar irradiation. The proposed methodology and topology is further validated using an experimental setup in the laboratory. [ABSTRACT FROM PUBLISHER]

This paper studies microgrids where loads are supplied by parallel-connected inverters controlled by decentralized active power/voltage frequency and reactive power-/voltage-magnitude droop control laws. A paralleled ac system, such as a multiinverter microgrid, is susceptible to circulating currents due to differences in voltage magnitude, frequency, phase angle, or dc offset. Circulating currents due to differences in voltage magnitude and dc offset have been known issues reported in literature. However, an in-depth analysis of the problem is required to ascertain the deviation of the system-operating condition from the desired condition. This paper provides a mathematical model that predicts the effect of voltage-magnitude offsets on reactive power sharing between inverters. Simulation and experimental results verify the accuracy of the analytical results obtained from the mathematical model. We examine the effect of dc-circulating currents and propose a simple capacitor emulation control law implemented in software to eliminate dc-circulating currents. This solution is a possible alternative for hardware implementation to eliminate dc-circulating currents. The effectiveness of the capacitor emulation control law has been verified through experimental results. [ABSTRACT FROM PUBLISHER]

The negative effects of pulse width modulated switch-mode inverters on electrical motors, such as failures in the motor windings isolation and electrical discharge machinery leading to motor bearing failures, are well known. Long cables between inverter and motor, very often found in, for example, railway applications, further increase these effects due to the cable reflections. The aim of this paper is to present an easy-to-use tool for practicing engineers, providing mathematical analysis, design, and optimization of the load ratio control common-mode filtering network at the inverter output. This topology has been chosen after a literature research and considering the practical experiences with different common mode filter (CMMF) topologies. First, a CMMF operation is explained. After that the filter is mathematically analyzed using Laplace domain, leading to the definition of the filter optimization criteria, and in the end the simulation and experimental results are presented. This procedure was used on converters on different trains and has confirmed its value in operation. [ABSTRACT FROM PUBLISHER]

Earlier studies have pointed out the limitations of conventional inverters, especially in high-voltage and high-power applications. In recent years, multilevel inverters are becoming increasingly popular for high-power applications due to their improved harmonic profile and increased power ratings. Several studies have been reported in the literature on multilevel inverters topologies, control techniques, and applications. However, there are few studies that actually discuss or evaluate the performance of induction motor drives associated with three-phase multilevel inverter. This paper presents then a comparison study for a cascaded H-bridge multilevel direct torque control (DTC) induction motor drive. In this case, symmetrical and asymmetrical arrangements of five- and seven-level H-bridge inverters are compared in order to find an optimum arrangement with lower switching losses and optimized output voltage quality. The carried out experiments show that an asymmetrical configuration provides nearly sinusoidal voltages with very low distortion, using less switching devices. Moreover, torque ripples are greatly reduced. [ABSTRACT FROM PUBLISHER]

The cost and efficiency of a photovoltaic (PV)-based grid-connected system depends upon the number of components and stages involved in the power conversion. This has led to the development of several single-stage configurations that can perform voltage transformation, maximum power point tracking (MPPT), inversion, and current shaping-all in one stage. Such configurations would usually require at least a couple of current and voltage sensors and a relatively complex control strategy. With a view to minimize the overall cost and control complexity, this paper presents a novel MPPT scheme with reduced number of sensors. The proposed scheme is applicable to any single-stage, single-phase grid-connected inverter operating in continuous conduction mode (C CM). The operation in CCM is desirable as it drastically reduces the stress on the components. Unlike other MPPT methods, which sense both PV array's output current and voltage, only PV array's output voltage is required to be sensed to implement MPPT. Only one current sensor is used for shaping the buck-boost inductor current as well as for MPPT. The information about power output of the array is obtained indirectly from array's voltage and the inductor current amplitude. Detailed analysis and the flowchart of the algorithm for the proposed scheme are included. Simulation and experimental results are also presented to highlight the usefulness of the scheme. [ABSTRACT FROM AUTHOR]