Search

In this paper, a new modulation strategy based on the carrier-based switching strategy for the non-square direct matrix converters (MC) is proposed to control the active power of distributed generation (DG) units. In this strategy, the active power of DGs is controlled by the central input current control of the non-square direct MC independent from the voltage and frequency. Conventionally, each DG has a converter, and for supplying a load with N number of DGs, N number of converters are needed and each converter has its own modulation switching and control strategy to control the power output of each DG. Needless to say, in a microgrid with N number of DGs, the control strategy of each converter has more complex structure than that of a microgrid with one converter, and surely the former strategy entails more volume and price. Using the proposed converter in this paper, it is possible to supply a load with N number of DGs through one converter. Also, the power outputs of all DGs are controlled by a central control strategy. The proposed central control strategy is described and simulated for a typical microgrid. Experimental and simulation results validate the effectiveness of the proposed converter and the proposed strategy. The results demonstrate the applicability and efficiency of the system and verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

Conventional model predictive control (MPC) for three-level active neutral point clamped converter (ANPC) utilizes weighting factors to achieve the optimal control of multiple control objectives in a single cost function. However, the selection of these weighting factors has an impact on the performance of the controlled objectives significantly. Tuning of weighting factors is usually tedious and lacks theoretical background. Moreover, the predictive and evaluation process for multiple objectives optimization have to be carried out by enumerating all admissible switching states within one loop. To simplify the complexity of this process and eliminate the effect of weighting factors, this paper proposes a cascaded predictive control scheme for a 3L-ANPC inverter fed induction machine (IM) drive. With the proposed approach, three separate cost functions for three control objectives, stator flux vector, neutral point voltage and device loss distribution are evaluated in a cascaded way, so that the optimization of these control objectives is performed independently. A 3L-ANPC inverter driven IM drive is studied in this paper to verify the effectiveness of the proposed algorithm. Experimental results in different operating conditions confirm that the proposed method achieves satisfactory steady-state and transient performances comparable to the conventional predictive control approach. The weighting factors used in the conventional method are eliminated and the computational effort is reduced by 68% compared to the conventional method without any sacrifice in the drive performance. [ABSTRACT FROM AUTHOR]

This paper presents a simple pulse width modulation algorithm for control of an ultracapacitor based energy storage system used for source and load support applications. As opposed to dual loop control philosophy that is widely used for backup applications, this paper presents a simple single loop current control that is only useful for controlling the ultracapacitor based DC/DC converters used in source and load support applications. The proposed PWM blocking method necessitates the DC/DC converter to operate in five states and takes into consideration the essential operational limits associated with the ultracapacitors. The performance of the proposed algorithm is verified experimentally using a 24 V laboratory prototype setup. Further, the shortcomings of dual loop control when applied to source and load support applications are demonstrated. [ABSTRACT FROM AUTHOR]

The digital implementation of all the control loops of a versatile buck-boost (VBB) dc–dc converter used in a stand-alone photovoltaic application is proposed in this paper to improve existing digital-analog sliding-mode-based implementations. All three control loops: maximum power point tracking (MPPT), fast input voltage regulation, and inner high-bandwidth current control, have been programmed in the same digital signal controller (DSC). A Model Predictive Control (MPC) based algorithm has satisfactorily solved the challenge of implementing the nominal 100 kHz switching frequency current loop. The MPC cost function is distributed throughout the algorithm to achieve three specific goals: the tracking of the reference current (G1), a quasi-constant steady-state switching frequency (G2), and the assurance that the duration of an interval is larger than the time required to calculate it (G3). The third goal requires the current control to toggle between peak- and valley-modes depending on the operating point. The correct fulfillment of these control objectives on the proposed MPC-based algorithm has been validated through simulations and experimental tests performed on a purpose built-prototype. [ABSTRACT FROM AUTHOR]

In this paper a control method for a matrix converter (MC) based on the heterodyne concept from the communication field is presented. The method is used to convert the high frequency of a microturbine generator’s (MTG) output voltage to the utility grid’s frequency. In this control method a frequency modulation (FM) of the MC’s switching frequency is achieved using a DQ0 analysis of the converter’s filtered output voltage with the utility grid’s frequency as a reference. After filtration, the MC achieves a conversion to the reference frequency with a minimal total harmonic distortion (THD) of the output voltage while using a low switching frequency. In addition, the proposed method decouples the output frequency, phase angle and voltage amplitude, which allows them to be controlled separately. This significantly simplifies the required control, and enables a robust and low-cost design. The theoretical analysis, simulation and experimental results of the method are reported. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dual input nine-level inverter (DINLI) topology which requires only seven controllable devices. The dual inputs are un-identical DC voltage sources in the ratio 1:3. A simple control scheme is derived by appropriately modifying the phase disposition pulse width modulation technique to generate high-quality 9-level output from the DINLI topology. At any given instant, a maximum of four switches conduct out of which only a maximum of two switches operate at high frequency, bringing down the switching and conduction losses significantly and improving the overall system efficiency. The bidirectional DINLI (BDINLI) topology with reactive power capability can be realized by replacing the unidirectional devices with the controlled switches (i.e., total nine switches). In addition, the proposed DINLI topology does not require extra voltage balancing circuits which further improves the efficiency. The DINLI operation is verified through MATLAB simulations for grid-connected applications and its extension to an n-level, 3-phase application is also investigated. Experiments performed on a 1KVA laboratory prototype to validate the theoretical claims. [ABSTRACT FROM AUTHOR]

In this paper, a finite-control-set model predictive direct torque control (FCS-MPDTC) method is proposed to reduce the torque ripple of a segmented switched reluctance motor (SSRM) at the low-speed stage. Firstly, the prediction dynamic model is established, and the phase torque can be predicted by detecting phase current and rotor position signals. Then, the principle of power converter and selection of voltage vectors are introduced and presented. Considering torque ripple reduction, flux tracking performance and copper losses reduction, the cost function with phase torque, the amplitude of flux linkage and phase current, is established to select optimal voltage vector to control the power converter. In addition, the torque sharing function (TSF) is employed to distribute total torque to phase torque for further torque ripple reduction. Finally, the direct torque control (DTC) is selected as the comparison method, performance of MPDTC is verified by simulation and experiment results. It can be found that the proposed MPDTC can achieve lower torque ripple and copper losses, and high robustness. [ABSTRACT FROM AUTHOR]

This paper presents a dual-hysteresis band control method for multi-drive systems based on a nine-switch inverter. The drive system contains two independent three-phase induction motors fed by a nine-switch inverter. Independent control of torque, speed, and stator current of two load stages is achieved. The proposed strategy offers a reliable control operation of both induction machines under individual load profiles. Instead of using independent sets of three-phase voltage source converters, the nine-switch inverter is used to drive separate machines. Thus, the volume and size of the power stage are noticeably reduced due to the use of fewer semiconductors. The theoretical concept and design steps of the proposed method are presented. The performance of the closed-loop independent motor control scheme is experimentally validated using a 3.2 kW lab-scaled nine-switch inverter prototype and Altera Cyclone IV Field-programmable gate array. [ABSTRACT FROM AUTHOR]

The main challenges for Finite Set-model Predictive Torque and Flux Control (MPTC) include huge calculation amount, large torque ripple, and the selection of weighting factor. To deal with these challenges and achieve the fastest torque response, a novel MPTC strategy with virtual voltage vector-based pattern is proposed in this paper. In each control period, a desired voltage vector is computed based on the maximum torque variation rate. The virtual desired voltage vector is combined by using basic voltage vectors with the minimum switching times. The switching pattern between two adjacent control periods is optimized by using a cost function in realtime. Compared with the traditional MPTC approach, the novel strategy has multifaceted improved performances: faster torque response, less calculation amount, lower switching frequency, reduced torque ripple, higher efficiency and no weighting factor. The proposed method is contrasted with traditional MPTC method and a well-known generalized multiple-vector-based MPC method via experiments. [ABSTRACT FROM AUTHOR]

This paper presents a new single-source three-phase seven-level inverter with an inherent three-time voltage boosting capability for medium-voltage applications. The proposed topology is comprised of series connection of two switched-capacitor (SC) networks with an added half-bridge module per phase. Each of such integrated SC networks requires a single capacitor associated with three active power switches. The three-time voltage boosting feature of the proposed topology can reduce the dc-link voltage requirements by 50% in comparison to the traditional neutral point clamped (NPC), flying capacitors, active NPC (ANPC), hybrid clamped ANPC, and cascaded H-bridge topologies, and 75% to advanced ANPC topologies. It can also reduce the number of required switches and capacitors as well as their voltage stresses compared to those state-of-the-art topologies reported in the literature. By integrating “n” number of added SC networks in the proposed seven-level basic topology, the number of output voltage levels can be extended to 2n+3 per phase. A finite control set model predictive control algorithm is also derived to control the converter in both the active and reactive power exchanges modes without distorting the generated grid current quality. The capacitor voltage balancing is inherent in the proposed topology, and thus, there is no need for any additional voltage balancing circuit, which further reduces the control complexity. The performance of the proposed topology and its control algorithm are validated by several measurement results. [ABSTRACT FROM AUTHOR]

An improved two-stage model predictive current control (MPCC) for three-phase three-level converters in the paper, which can simultaneously achieve common-mode voltage (CMV) reduction, effective dc-link capacitor voltage control, and decreased computational burden, is proposed. Compared to the other current control strategies, it has the capability of handling multiple control objectives and possesses a simple structure. Furthermore, it greatly reduces the CMV since the peak CMVs of all the candidate voltage vectors are constrained to be less than one sixth of the dc-link voltage. In addition, an optimal two-stage voltage vector selection mechanism is employed in the proposed method. It helps to significantly reduce the computational complexity. Simulation and experimental results are provided to verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

The implementation of finite-control-set model predictive control (FCS-MPC) in voltage source inverters (VSIs) can make the system suffer from poor current harmonics performance, which may complicate the design of the required AC filter. To overcome this shortcoming, a carrier-based modulated model predictive control (CB-MMPC) strategy is proposed in this paper. This method enables the utilization of existing PWM modulation techniques with FCS-MPC, where a modulation waveform with zero-sequence signal injection is generated and compared to a triangular carrier wave, while optimizing the selection of the switching states. As it is shown, the studied CB-MMPC strategy not only considerably improves the current total harmonic distortion (THD) but also attains the performance of fast current dynamic response and robustness as the traditional FCS-MPC. Herein, the detailed implementation of the CB-MMPC control strategy is given, while considering its application to the current feedback control loop of a three-phase three-wire two-level VSI modulated at constant switching frequency. Finally, PLECS circuit simulation and a 3-kW VSI prototype are used to verify the superiority and the effectiveness of the presented CB-MMPC strategy. This is also benchmarked to the FCS-MPC and dead-beat based controllers. [ABSTRACT FROM AUTHOR]

Conventionally, the converter of switched reluctance motor (SRM) is fed by the uncontrollable diode bridge rectifier (DBR), which leads to a low grid-side power factor (PF) and high current total harmonic distortion (THD). In this paper, an alternative solution for the grid-connected high-speed SRM drive system with improved PF is proposed. In the proposed drive system, the three-level active front end (AFE) is connected in cascade with the midpoint converter for SRM operation. A centralized strategy, which controls the AFE and SRM together, is proposed to govern the motor speed and grid-side PF by regulating the real power and reactive power of the system, respectively. Specifically, the real power, reactive power, and the voltage balancing of split capacitors are controlled by the model predictive directed power control (MP-DPC) algorithm, which significantly reduces the control complexity and guarantees the fast dynamic response. Consequently, satisfying speed regulation, high PF, low current THD, and bi-directional power-transfer capability are achieved. An idea-proofed testbench is constructed in laboratory, and the applicability of the proposed drive system is verified by a series of experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a new control strategy using model-based predictive current control (MB-PCC) for a doubly fed induction machine (DFIM) driven by an indirect matrix converter (IMC). This strategy proposes the control of rotor currents, whose references are calculated from active and reactive stator power set points and the dynamic model of the DFIM. The control strategy works well in the four P-Q operating regions of the DFIM. The grid synchronization process is carried out by setting the P-Q power set points to zero. The results include the DFIM synchronization procedure as well as the active and reactive power control at variable shaft speed to validate the feasibility of the proposed strategy. [ABSTRACT FROM AUTHOR]

In dc microgrid, energy storage system (ESS) plays a crucial role to provide short-or-long term and high-quality electric energy. The different control strategies for bidirectional dc-dc converter (BDC) of ESS in grid-tied and islanded modes pose challenges to the coordination control of the dc microgrid. This paper proposes an autonomous control scheme for the BDC in dc microgrid. The proposed control scheme is based on $V^2-P$ droop control and unifies bus voltage regulation and power regulation in a single control structure. Thus, global smooth transition between various operation modes can be achieved without any control strategy changes, which avoids various mode switch detection mechanisms and improves system stability. Furthermore, the proposed control scheme is fully decentralized which reduces the reliance on communication, and enhances the reliability of the microgrid. On the other hand, $V^2-P$ droop approach eliminates the negative effect of widespread constant power loads (CPLs) in dc microgrid. The stability of the proposed control method is illustrated, and the design guideline of some critical control gains is addressed. Finally, the effectiveness of the proposed control scheme is validated by the real-time hardware-in-loop (HIL) platform. [ABSTRACT FROM AUTHOR]

Recent technical advances in control, protection and interconnection of distributed power generation units imply that it is practically viable and economically profitable to keep them as backup generators in isolated operating modes. Therefore, along with the development of islanding detection techniques, seamless operation in transition between islanded and grid connected modes is required and more sophisticated control strategies are needed to recognize the existing working condition and adjust the performance to meet the strict standards of grid interconnection. This paper presents a new adaptive control structure, based on internal model control (IMC), which uses multiple models and an inherent islanding detection method through an optimized switching mechanism to tune the operation of a three-phase inverter under transitions between islanded and grid-tied conditions. By applying a power synchronization method, the system emulates the operation of a synchronous machine which is needless to rely on a phase-locked loop to synchronize during the transitions. Hardware co-simulation environment in Simulink/PLECS and Xilinx System Generator have been utilized to evaluate the transient behavior of the controller in discretized domain and verify its robustness during parameter variations and load switching conditions. Various switching rules have been applied and a comparison of their effect in transient response is demonstrated. The results, taken from several case studies, confirm the significant robustness of the proposed control methodology. [ABSTRACT FROM AUTHOR]

This paper presents a modification of the Vienna rectifier (VR) to obtain more than three voltage levels at the DC line connection, while preserving the unity power factor at the AC grid side. The proposed unidirectional multilevel there-phase rectifier, called the “Negev rectifier”, has a reduced device count and utilizes a unique novel Time Division Multiplexed based control scheme, which makes the challenging N-level VR expansion possible. The Negev rectifier can serve as a grid interface for supplying dc voltage to multilevel inverters with 4 up to 7 voltage levels, eliminating the burden of inverter-side voltage balancing control. The Negev hardware can be constructed by two complementary topologies, making it suitable for either high current or high voltage applications. [ABSTRACT FROM AUTHOR]

The large amount of power electronic submodules and semiconductor switching events in the Modular Multilevel Converter (MMC) introduces several challenges for efficient and accurate Electro-Magnetic Transient (EMT) simulation. Research efforts have focused on developing Average Value Models (AVMs) of MMC that enable fast and accurate dynamic simulation of the converter. This paper proposes a universal blocking-module-based AVM, which can simulate the MMC of different submodule types and provide accurate results for the MMC operating in both blocking and de-blocking modes. An analytical approach is included in the model to calculate the semiconductor losses of different submodule types in the MMC. The proposed model is validated against a detailed switching-based model and the state-of-the-art AVMs in a 41-level two-terminal MMC-HVDC system. [ABSTRACT FROM AUTHOR]

Modeling and simulation play a vital role in the design and testing of modular multilevel converter (MMC) high voltage direct current (HVDC) systems. Detailed equivalent model (DEM) and switching-function-based average value model (SFB-AVM) are two major types of accurate and efficient models to represent the dynamic response of the MMCs. However, the DEM and the SFB-AVM possess unique benefits depending on the purpose of the simulation studies. The DEM provides a detailed representation of submodule (SM) switching events and individual capacitor ripples. The SFB-AVM provides faster simulation speed by using arm equivalent capacitance. Combining both models in a universal arm equivalent circuit gives the users the choice of selecting the most appropriate modeling method during dynamic simulation. This paper proposes a universal modeling framework combining the DEM with the SFB-AVM which allows the DEM and the SFB-AVM smoothly switch from one to the other during dynamic simulation. The proposed SFB-AVM can accurately represent the MMCs with different SM types. The proposed models are validated in offline and real-time simulation studies which demonstrate the improved simulation speeds of the proposed SFB-AVM over the DEM especially for large numbers of SMs. [ABSTRACT FROM AUTHOR]

Grid connected voltage source converters are inevitable means now for expanding and supporting power systems. Nevertheless, their harmonic injection and high frequency switching may cause degradation of power quality and detraction of the equipment reliability. Therefore, the converters injected harmonics must observe the corresponding standards, while lower switching frequencies and rapid transient responses are desirable. In this paper, a new combined control method with a flexible switching table is presented for the converters to enhance the power quality and transient response. The method employs a virtual flux in connection with a combined control for the first time. In comparison with the conventional virtual flux direct power control, the proposed method provides better power quality, reduced THD and faster transient response, in addition to less grid parameters dependency. Compared to the conventional combined control method, it determines more accurately the converter voltage vectors, while avoiding grid voltage measurement and cumbersome controller tuning. [ABSTRACT FROM AUTHOR]

Reliability of power systems can be improved by the use of voltage source inverters (VSIs) with fast dynamic control, which can handle uncertainties induced by renewable energy resources and nonlinear loads. To ensure fast-dynamic response and simplified controller design, various model predictive control (MPC) methods are investigated in this paper. In the conventional MPC design for three-level VSIs, the cost function requires an additional term to ensure the balance of the neutral-point voltage (NP-V), which however can considerably impact the main goal of the MPC. To address this issue, an enhanced MPC using virtual space vectors is proposed, which allows the use of a significantly reduced weighting factor for the term in the cost function for NP-V balancing, while retaining fast-dynamic response. Additionally, the proposed MPC leads to reduced harmonic distortion in the VSI output voltage and current. Both simulation and controller hardware-in-the-loop studies are performed to demonstrate the effectiveness of the proposed enhanced MPC in an operating microgrid under both steady-state and fast-transient conditions. [ABSTRACT FROM AUTHOR]

An enhanced DC–DC converter is proposed in this paper, based on the combination of the Cuk and SEPIC converters, which is well-suited for solar photovoltaic (PV) applications. The converter uses only one switch (which is ground-referenced, so simple gate drive circuitry may be used), yet provides dual outputs in the form of a bipolar DC bus. The bipolar output from the DC–DC converter is able to send power to the grid via any inverter with a unipolar or bipolar DC input, and leakage currents can be eliminated if the latter type is used without using lossy DC capacitors in the load current loop. The proposed converter uses integrated magnetics cores to couple the input and output inductors, which significantly reduces the input current ripple and hence greatly improves the power extracted from the solar PV system. The design methodology along with simulation, experimental waveforms, and efficiency measurements of a 4-kW DC–DC converter are presented to prove the concept of the proposed converter. Furthermore, a 1-kW inverter is also developed to demonstrate the converter's grid-connection potential. [ABSTRACT FROM AUTHOR]

The non-inverting buck-boost converter has emerged as one of the most promising topologies for distributed maximum power point tracking applications. Pressure to reduce cost and volume of photovoltaic module integrated converters often compels bootstrap capacitor type gate drivers. The bootstrap technique is a simple and economical solution to create a floating power supply for high-side gate drivers. However, it comes with a major challenge, as the low-side switch must be periodically turned on, to recharge the high-side bootstrap capacitor. In the buck and the boost mode, one of the switching legs of the converter must be held with the high-side switch on, which eventually discharges the high-side capacitor. When the non-inverting buck-boost input voltage is regulated by means of a single voltage loop, recharging the bootstrap capacitor causes an undesired ripple in the PV module voltage, degrading the regulation quality. In order to mitigate this problem, this paper proposes a cascaded control technique, entailing regulation of the PV module voltage and inductor current. The cascaded controller dramatically improves the rejection of the disturbance induced by the periodic recharge of the bootstrap capacitor, thanks to the fast action of the current loop, regulating the average value of the inductor current. Converter transfer functions and controller design are derived and validated. Experimental results clearly show that the cascaded control scheme outperforms the traditional voltage control scheme, resulting in a better regulation of the PV module voltage. This main advantage comes at the cost of an additional measurement of the average inductor current. [ABSTRACT FROM AUTHOR]

An isolated single sourced multi-output dc/dc converter with a high-frequency link was proposed before to feed different cells of the Asymmetrical Cascaded H-bridge (ACHB) inverter. One of the fundamental advantages of the ACHB is that the main H-bridge is commutated with fundamental frequency, passing the majority of the inverter power. However, the isolated dc/dc converter needs to be connected to the main voltage source with high-voltage/high-frequency switches, which limits the power capability and the efficiency of the converter. In this paper, a switching pattern based on nearest level modulation method is proposed to command all the power to be transferred through the main H-bridge. Therefore, the power circulates between the auxiliary H-bridges with no need for high-voltage switches. As a result, a single-input single-output auxiliary converter is needed with only 5% of the power rating. This solution reduces cost and size while it improves the efficiency of the converter. Furthermore, the architecture makes the inverter more suitable for high power and high-voltage applications. The inverter switching strategy is based on programmable firing angles. The main dc-link of the grid connected inverter is controlled to achieve maximum power point tracking, while the dc/dc isolated converter is controlled to regulate the auxiliary dc-links. The proposed topology is verified by simulation and experimental results using a 1.5 kW hardware prototype. [ABSTRACT FROM AUTHOR]

Stand-alone microhydro systems based on the self-exited induction generator (SEIG) are popular in developing countries. However, an electronic based controller is required to maintain the quality (voltage and frequency) of the generated power within an acceptable range. Conventionally, this controller is designed using a phase-controlled thyristor circuit (or more recently using a dc chopper circuit) and a fixed resistance dump load to receive the excess generated power. Generally, in small communities the total dissipated power in the dump load is greater than the consumed power by all the households. This problem of inefficient power usage can be solved by distributing the controller among households. The objective of this paper is to improve the distributed electronic load controller (DELC). As with the original DELC, the proposed improved DELC is used for two purposes: First, consuming the excess generated power individually by each household; and second, operating as a complementary device for voltage and frequency regulation of the SEIG. The detailed design and experimental verifications of the proposed improved DELC including the design of an appropriate input filter to minimize the network current distortion are presented here. Additionally, MATLAB simulations are used to study the interaction between the proposed improved DELC and the powerhouse controller (the ELC). [ABSTRACT FROM AUTHOR]

Direct power control (DPC) has gained much attention for medium-voltage applications due to its fast power control capability. However, a conventional static switching table based DPC can lead to unsatisfactory response when the converter is connected to an electric grid because it is commonly designed assuming ideal and constant voltages of the grid and the dc link. Therefore, the actual grid voltage and the actual converter dc-link voltage should be considered while designing the switching table. This paper proposes a novel dynamic switching table for the DPC, considering actual grid and dc-link voltages variation. The proposed dynamic switching table incorporates a new definition of power influence crossover angles of each converter space vector. The proposed scheme dynamically adapts the switching table by feeding forward the actual grid and dc-link voltages, and hence the converter's power is precisely controlled. The proposed technique is verified for the three-level neutral point clamped converters connected to a standard IEEE 9-bus test system. Moreover, the real-time simulations are performed in a real-time digital simulator, OPAL-RT. The obtained results verified the effectiveness of the proposed DPC strategy under different grid fault scenarios. [ABSTRACT FROM AUTHOR]

This paper proposes a simplified and improved model predictive current control (MPCC) scheme for grid-connected bidirectional voltage source converter (GC-BVSC) when the unbalanced grid voltages occur. In conditions of unbalanced grid voltage, the current harmonic components of the GC-BVSC increase significantly, and twice grid-frequency ripple exist in both active power and reactive power, which influence the output power quality. To reduce harmonic currents and power fluctuations, an improved MPCC (IMPCC) method is proposed, and a two-step predictive model of GC-BVSC is put forward. The current compensation values are expressed by grid voltages and their quadrature signals that lag 90 electrical degrees in the αβ stationary coordinates system. The cost function reducing both the power ripple and current distortion is designed. Compared to conventional methods, phase-locked loop, pulse width modulation, and complex positive and negative sequence extraction of grid voltage are not required. In addition, IMPCC presents a better performance by reducing both grid-connected current harmonics and power ripple of GC-BVSC with flexible bidirectional power regulation capability. Simulation and experimental results on power electronics-professional (PE-PRO) platform verify the effectiveness of the proposed scheme under both single-phase and three-phase unbalanced grid voltages. [ABSTRACT FROM AUTHOR]

This paper is the continuation of Part I in which an online reference limitation strategy for shunt-connected converters is presented. This limitation strategy is successfully validated in this Part II of the paper by means of experimental results obtained in a laboratory setup. Two different experiment sets are carried out in order to check the two application scenarios described in Part I. On the one hand, the limitation strategy is implemented in the STATCOM application reducing the reactive power reference. On the other hand, the grid balancer functionality is implemented together with the new limitation strategy reducing the current references. In this last scenario, two different experiments are shown: 1) a switching-on of the converter; and 2) a voltage variation at the point of common coupling. In both functionalities, the corresponding reference limitations are activated due to overcurrent and overvoltage cases and the limitation due to the dc bus voltage oscillations is validated in the grid balancer functionality. [ABSTRACT FROM AUTHOR]

This paper presents as a new contribution a proposal to optimize the performance of a switched reluctance generator (SRG) in a variable wind energy conversion system. An approach based on the design of computational experiment is applied to determinate the optimal firing angles and the optimal dc link voltage that guarantee the best system behavior for each rotor speed. A third-order response surface model based on space-filling designs is applied to build a multiobjective function considering efficiency improvement and torque ripple reduction. An interior point method is applied to find the minimum of the surface, optimizing the process. Direct power control is used to obtain the maximum power as a function of the rotor speed, employing the optimal parameters. Hysteresis and single-pulse current control are applied for low- and high-speed operation, respectively. Simulation and experimental results have shown that the proposed approach returned a good compromise between SRG high efficiency and low torque ripple. Moreover, the presented technique reduces computational effort and provides a clear massive data simulation framework. [ABSTRACT FROM AUTHOR]

Switched reluctance motor (SRM) drives conventionally use current control techniques at low speed and voltage control techniques at high speed. However, these conventional methods usually fail to restrain the torque ripple, which is normally associated with this type of machine. Compared with conventional three-phase SRMs, higher phase SRMs have the advantage of lower torque ripple: To further reduce their torque ripple, this paper presents a control method for torque ripple reduction in six-phase SRM drives. A constant instantaneous torque is obtained by regulating the rotational speed of the stator flux linkage. This torque control method is subsequently developed for a conventional converter and a proposed novel converter with fewer switching devices. Moreover, modeling and simulation of this six-phase SRM drive system has been conducted in detail and validated experimentally using a 4.0-kW six-phase SRM drive system. Test results demonstrate that the proposed torque control method has outstanding performance of restraining the torque ripple with both converters for the six-phase SRM, showing superior performance to the conventional control techniques. [ABSTRACT FROM AUTHOR]

This paper proposes a hybrid pulse width modulation (PWM) based field weakening control strategy for a hybrid-inverter-driven open-winding (OW) permanent magnet synchronous motor (PMSM) system. The hybrid-inverter consists of two voltage source inverters, one is connected to a dc voltage source and named as main inverter (MI), and the other is connected to a floating capacitor and called compensation inverter (CI). A novel hybrid PWM technique is proposed for the hybrid-inverter, in which a double-vector-based PWM is applied to the MI to reduce the switching frequency, and the conventional space vector PWM is applied to the CI to compensate the reactive power. Furthermore, a field weakening (FW) control strategy based on the hybrid PWM technique is proposed to better utilize the dc-link voltage and extend the operation range of the OW-PMSM system. Simulation and experimental studies are carried out to verify the high efficiency and wide speed range of the proposed strategy. [ABSTRACT FROM PUBLISHER]

This paper proposes a generalized direct torque control (DTC) strategy for multilevel inverter fed DTC (MLI-DTC) drives. By using a simple voltage vector decomposition technique, the proposed method is compatible with inverters possessing any number of voltage levels. Consequently, voltage vectors are applied in a similar way as in the case of a two-level inverter fed DTC. A constant inverter switching frequency is imposed in the proposed method by using a torque regulator in place of the traditional torque hysteresis controller, which enables the application of two voltage vectors within one switching cycle. This also contributes to reduce the torque and flux ripples. Detailed design guidelines for the proposed torque regulator are provided. Experimental results obtained with a three-level neutral point clamped inverter show that the proposed MLI-DTC drive operates with low, constant switching frequency while alleviating torque and flux ripples under all operating conditions. Comparative study with a prior art and parametric sensitivity analysis are also presented to verify the effectiveness and robustness of the proposed MLI-DTC method. [ABSTRACT FROM PUBLISHER]

As penetration of distributed generation increases, the electrical distribution networks may encounter several challenges mainly related to voltage control. The situation may deteriorate in case of a weak grid connected to an intermittent source such as photovoltaic (PV) generation. Fast varying solar irradiance can cause unacceptable voltage variations that may not be easily compensated by slow-responding utility equipment. The PV inverter can be used to control the grid voltage by injecting/absorbing reactive power. A small-signal model is derived in order to study the stability of a PV inverter exchanging reactive power with the grid. This paper also proposes a method that utilizes the available capacity of the PV inverter to support the grid voltage without violating the rating of the inverter and the maximum voltage that the inverter's switching device can withstand. The method proposed in this paper is validated using PSCAD/EMTDC simulations. [ABSTRACT FROM PUBLISHER]

This paper proposes a model predictive direct power control (MPDPC) approach with reduced switching frequency for grid-connected voltage-sourced converters (VSC). This approach is proposed for both a real/reactive power controller (with a fixed input voltage) and a power port controller (with a variable input voltage). It uses two different cost functions: one for the steady state and one for transients. Utilizing these two cost functions leads to having a low switching frequency in the steady state and a fast response during transients. The proposed MPDPC also provides overcurrent protection of the VSC. In applying the proposed MPDPC to a power port, drawbacks of conventional voltage controllers are addressed by employing power estimation and set point modulation in the controller. Simulation and experimental results validate the proposed MPDPC and the voltage controller. [ABSTRACT FROM PUBLISHER]

The flying-capacitor-based multilevel converter is one of the well-known breeds of the multilevel power converters. This paper proposes a new flying-capacitor-based multilevel converter to minimize the number of flying capacitors (FCs) and power switches. The advantage of the proposed FC-based multilevel converter in comparison with the conventional flying-capacitor multicell converter is that it needs fewer FCs. Also, in comparison with the stacked multicell converter, the proposed multilevel converter requires fewer semiconductor switches. In order to balance the voltage of the FCs in proposed multilevel converter, a new active voltage balancing method which is fully implemented using logic-form equations is presented. The proposed voltage balancing method measures output current and FC voltages to generate switching states to produce the required output voltage level, as well as balance the FCs voltages at their reference values. The output voltage of the proposed multilevel converter controlled with suggested active voltage balancing method can be modulated with any pulse-width-modulation (PWM) method, such as phase-shifted-carrier PWM or level-shifted-carrier PWM. Simulation results and experimental measurements of proposed FC-based multilevel converter are presented to verify the performance of the proposed converter, and its novel switching and modulation strategy, which is based on the active voltage balancing method. [ABSTRACT FROM PUBLISHER]

In this paper, a wind energy conversion system interfaced to the grid using a dual inverter is proposed. One of the two inverters in the dual inverter is connected to the rectified output of the wind generator while the other is directly connected to a battery energy storage system (BESS). This approach eliminates the need for an additional dc–dc converter and thus reduces power losses, cost, and complexity. The main issue with this scheme is uncorrelated dynamic changes in dc-link voltages that results in unevenly distributed space vectors. A detailed analysis on the effects of these variations is presented in this paper. Furthermore, a modified modulation technique is proposed to produce undistorted currents even in the presence of unevenly distributed and dynamically changing space vectors. An analysis on the battery charging/discharging process and maximum power point tracking of the wind turbine generator is also presented. Simulation and experimental results are presented to verify the efficacy of the proposed modulation technique and battery charging/discharging process. [ABSTRACT FROM AUTHOR]

Conventional model-predictive torque control (MPTC) requires tedious and time-consuming tuning work for stator flux weighting factor, and presents relatively high torque ripples. To solve these problems, this paper proposes a model-predictive flux control (MPFC) for two-level inverter-fed induction motor (IM) drives. The references of stator flux magnitude and torque in conventional MPTC are converted into an equivalent reference of stator flux vector in the proposed MPFC. As only the tracking error of stator flux vector is required in the cost function, the use of weighting factor is eliminated. The optimal voltage vector is selected based on the principle of stator flux error minimization and its switching instant is optimized rather than being in the beginning of each control period. The proposed MPFC with and without switching instant optimization are both implemented in a 32-bit floating digital signal processor, and they are compared in detail in terms of torque ripple, current harmonics, and average switching frequency. Both digital simulations and experimental tests were carried out on a two-level inverter-fed IM drive, and the obtained results validate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents the development of a wind switched-reluctance generator (SRG) with interleaved interface dc–dc converter. First, the power circuit and control scheme of the SRG are properly designed. The hysteresis current-controlled pulse width modulation (PWM) scheme is designed to achieve good winding current tracking control, and the robust voltage control scheme is developed to yield well-regulated dc output voltage under varying prime mover driving speed and load conditions. Moreover, the voltage regulation and the developed power performances of SRG are further enhanced using the proposed commutation shift approach. Next, an interleaved current-fed push–pull interface dc–dc converter with two modules is developed to establish the boosted common dc bus voltage of a dc microgrid from the SRG output having fault-tolerant capability. The rating analysis and circuit component design are conducted in detail. Similarly, well-regulated voltage with lower ripples is also yielded via the properly designed schematic and control scheme. [ABSTRACT FROM AUTHOR]

In this paper, we present virtual prototyping of the distributed control for a modular multilevel inverter used as a grid-tie interface for photovoltaics. Due to the distributed control and inherent redundancy in the system composed of many panels and inverter modules, the system topology exhibits fault-tolerance capabilities that we study through virtual prototyping. The fault-tolerance is enabled by several distributed algorithms, such as services to identify which, if any, agents controlling inverter modules have failed. A distributed identifier algorithm allows the system to keep track of the number of operating panels to appropriately regulate the dc voltage output of the panels using buck–boost converters and determine appropriate switching times for H-bridges in the grid-tie. We evaluate the distributed inverter, its control strategy, and fault-tolerance through thousands of simulation scenarios in Mathworks Simulink/Stateflow. Our virtual prototyping framework allows for generating multilevel inverters composed of many inverter modules, and we evaluate inverters composed of five to dozens of inverter modules. Our analysis suggests the achievable total harmonic distortion of the modular multilevel inverter may allow for operating solar arrays in spite of failures of the power electronics, control software, and other subcomponents. [ABSTRACT FROM AUTHOR]

In a dc distribution system, where multiple power sources supply a common bus, current sharing is an important issue. When renewable energy resources are considered, such as photovoltaic (PV), dc/dc converters are needed to decouple the source voltage, which can vary due to operating conditions and maximum power point tracking (MPPT), from the dc bus voltage. Since different sources may have different power delivery capacities that may vary with time, coordination of the interface to the bus is of paramount importance to ensure reliable system operation. Further, since these sources are most likely distributed throughout the system, distributed controls are needed to ensure a robust and fault tolerant control system. This paper presents a model predictive control-based MPPT and model predictive control-based droop current regulator to interface PV in smart dc distribution systems. Back-to-back dc/dc converters control both the input current from the PV module and the droop characteristic of the output current injected into the distribution bus. The predictive controller speeds up both of the control loops, since it predicts and corrects error before the switching signal is applied to the respective converter. [ABSTRACT FROM AUTHOR]

The multichannel generator is a kind of special generator, which is developed to enhance power reliability in safety critical applications. This paper compares the dynamic performance computation for a 12/8 dual-channel switched reluctance generator (DCSRG) under single- and dual-channel operation modes. First, the static phase self- and mutual inductances are numerically calculated through finite element analysis (FEA). Based on the magnetic characteristics, the mathematical and simulation models of DCSRG under different operation modes are presented. In the dual-channel model, the effect of mutual coupling between phases of each channel in the DCSRG is considered. By using these proposed dynamic models, the different performances for the DCSRG under single- and dual-channel operation modes, such as generating process under closed-loop control, steady-state performance at different conditions, sudden change in load operation, and the operating status when changing from motoring to generating, are predicted and compared. Finally, a 12/8 DCSRG system is built for experimentation. The simulation and experimental results are also compared in the DCSRG system under different operation modes to verify the proposed modeling and analysis. [ABSTRACT FROM AUTHOR]

Regarding doubly fed induction generator (DFIG) operation, unbalanced and harmonically distorted grid voltage conditions have been treated as two separate control problems. This paper reports a solution for the rotor- and grid-side power converters, which allows one to keep the DFIG successfully in operation under both grid voltage conditions. The proposed solution is based on sliding-mode control (SMC). The rotor-side converter is commanded so that the electromagnetic torque and the stator reactive power remain free of fluctuations that arise during grid voltage disturbances. Meanwhile, the grid-side converter ensures both constant DC-link voltage and steady active power output from the overall system. The developed algorithms turn out being robust against parameter variations and of fast dynamic response. In addition, none of the converters need either voltage or current positive and negative sequences extraction. The simulation results presented demonstrate the appropriateness of SMC to face such disturbed scenarios. Finally, the stability proof of both converters’ control algorithms is provided in the appendices. [ABSTRACT FROM PUBLISHER]

Due to the increase of the number of wind turbines connected directly to the electric utility grid, new regulator codes have been issued that require low-voltage ride-through capability for wind turbines so that they can remain online and support the electric grid during voltage sags. Conventional ride-through techniques for the doubly fed induction generator (DFIG) architecture result in compromised control of the turbine shaft and grid current during fault events. In this paper, a series passive-impedance network at the stator side of a DFIG wind turbine is presented. It is easy to control, capable of off-line operation for high efficiency, and low cost for manufacturing and maintenance. The balanced and unbalanced fault responses of a DFIG wind turbine with a series grid side passive-impedance network are examined using computer simulations and hardware experiments. [ABSTRACT FROM AUTHOR]

Line-commutated thyristor-controlled rectifiers are often used in many industrial and renewable energy applications where controllable dc voltage is required. The derivation of accurate dynamic average-value models for thyristor-controlled systems is challenging. The recently proposed parametric average value modeling (PAVM) avoids the discrete switching states of the converters and results in computationally efficient models that are suitable for system level studies. This paper extends the PAVM recently developed for synchronous-machine-fed thyristor-controlled-rectifier systems to a permanent magnet synchronous machine wind generation system where the operation in variable speed and frequency is required. [ABSTRACT FROM PUBLISHER]