Search

In this paper, a fault-tolerant control of a symmetrical six-phase induction generator based on a variable structure strategy is experimentally tested and compared with a classical proportional-integral controller. For this, we use a linear feedback sliding mode controller with switched feedback gains in such a way to control the inner current loops of this machine. One main drawback of the classical three-phase induction generator is that it is no longer possible to generate electrical power if only one phase is lost on the stator side. To overcome this issue, we will use a squirrel cage six-phase induction machine that can still operate when at least three phases remain on the stator side. This article proposes to use a variable structure control in order to cope with unbalanced currents and also maintain the generation of power when a loss of the stator's phases occurs. The proposed controller shows its robustness and good regulation performance in healthy and faulty modes. The simulation and experimental tests were carried out with a 24 kW induction machine that represents 1/100 of the electrical power of a real wind turbine. [ABSTRACT FROM AUTHOR]

In this paper, a circulating-current-excited switched reluctance generator system with the diode rectifier is comparatively studied with a field-current-separated switched reluctance generator. By using a DC power source connected in series with the winding to provide the circulating current, a controllable excitation field is established in the proposed generator. To highlight the influence of this DC voltage source, the injected field current of the field-current-separated generator is kept the same as the circulating current of the circulating-current-excited generator. Then, both advantages and disadvantages of the generators are summarized. The circulating-current-excited switched reluctance generator system inherits both the advantages of good reliability of the separated-winding generator by using the diode rectifier and low copper loss of the integrated-winding machine by combining the AC and DC current in one set of windings. Furthermore, two more practically conventional field-current-separated generators are also compared with the proposed generator in terms of the external characteristics. These two conventional generators have different winding configurations. At last, the analysis is verified by experiments. [ABSTRACT FROM AUTHOR]

The belt-driven starter/generator (BSG), as a cost-effective solution, has been widely employed in hybrid electric vehicles (HEVs) to improve the stability and reduce the fuel consumption of the vehicles. It can provide more than 10% reduction in CO2. Electrical machine is the heart of the BSG system, which is functioned both as motor and generator. In order to optimize both aspects of motor and generator simultaneously, this paper presents a new multimode optimization method for the switched reluctance machines. First, the general multimode concept and optimization method are presented. The switched reluctance motor and the switched reluctance generator are the two operation modes. The optimization models are established based on motor and generator functions. Sensitivity analysis, surrogate models and genetic algorithms are employed to improve the efficiency of the multimode optimization. Then, a design example of a segmented-rotor switched reluctance machine (SSRM) is investigated. Seven design variables and four driving modes are considered in the multiobjective optimization model. The Kriging model is employed to approximate the finite element model (FEM) in the optimization. Finally, the optimization results are depicted, and an optimal solution is selected. The comparison between the initial and optimal designs shows that the proposed method can improve the foremost performance of the SSRM under all driving modes. [ABSTRACT FROM AUTHOR]

This paper presents the development of a wind switched-reluctance generator (SRG) with interleaved interface dc–dc converter. First, the power circuit and control scheme of the SRG are properly designed. The hysteresis current-controlled pulse width modulation (PWM) scheme is designed to achieve good winding current tracking control, and the robust voltage control scheme is developed to yield well-regulated dc output voltage under varying prime mover driving speed and load conditions. Moreover, the voltage regulation and the developed power performances of SRG are further enhanced using the proposed commutation shift approach. Next, an interleaved current-fed push–pull interface dc–dc converter with two modules is developed to establish the boosted common dc bus voltage of a dc microgrid from the SRG output having fault-tolerant capability. The rating analysis and circuit component design are conducted in detail. Similarly, well-regulated voltage with lower ripples is also yielded via the properly designed schematic and control scheme. [ABSTRACT FROM AUTHOR]

Fault ride-through (FRT) is a common requirement to abide by grid code all over the world. In this paper, to enhance the FRT capability of fixed speed wind generator system, a modified configuration of bridge-type fault current limiter (BFCL) is proposed. To check the effectiveness of the proposed BFCL, its performance is compared with that of the series dynamic braking resistor (SDBR). A harmonic performance improvement by the proposed method is also analyzed. A three-phase-to-ground (3LG) fault was applied to one of the double circuit transmission lines connected to the wind generator system. Simulation was carried out by using MATLAB/Simulink software. Simulation results show that the proposed BFCL is a very effective device to achieve the FRT and suppress fault current that eliminates the need for circuit breaker replacement. Also, the BFCL improves the harmonic performance and helps follow harmonic grid code. Moreover, it was found that the BFCL works better than the SDBR and has some distinct advantages over the SDBR. [ABSTRACT FROM PUBLISHER]

Line-commutated thyristor-controlled rectifiers are often used in many industrial and renewable energy applications where controllable dc voltage is required. The derivation of accurate dynamic average-value models for thyristor-controlled systems is challenging. The recently proposed parametric average value modeling (PAVM) avoids the discrete switching states of the converters and results in computationally efficient models that are suitable for system level studies. This paper extends the PAVM recently developed for synchronous-machine-fed thyristor-controlled-rectifier systems to a permanent magnet synchronous machine wind generation system where the operation in variable speed and frequency is required. [ABSTRACT FROM PUBLISHER]