Search

This paper presents a unified second-stage LC filter applied in the three-state switching cell buck–boost converter, which provides current and voltage with low ripple and low noise. The unified second-stage filter promotes a reduction in the number of devices while maintaining the filtering performance of the converter, with second-stage LC filters at the input and at the output. Moreover, the unified filter, when associated with a three-state switching cell buck–boost converter, allows a size reduction of filter devices, especially for designs with duty cycle range around 1/2. Furthermore, the unified filter arrangement provides nondissipative clamping of switching devices and reduce the system order when compared to the converter with second-stage LC filters. In this paper, the static and dynamic characteristics of the proposed converter in continuous conduction mode (CCM) are reported. Experimental data were obtained from a laboratory prototype with an input range of 32 $\sim$ 72 V, constant output of 48 V, a load of 150 W, and switching frequency of 45 kHz. The measured efficiency for the rated load was 97% for maximum input voltage. A comparison of the size and performance of the proposed filter with the topology that uses second-stage LC filters at the input and at the output is also presented. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

This paper presents a novel integrated-stage light-emitting diode (LED) driver based on Flyback and resonant converters. The Flyback converter realizes power factor correction in the discontinuous conduction mode. The resonant converter is operated as a dc–dc converter to support the LED loads. Moreover, the resonant converter can clearly decrease the drain–source voltage of the active switch and exhibits zero-voltage-switch characteristics. Therefore, a cost-effective MOSFET can be chosen as the main control component that can decrease the cost of the whole system. Compared to a single-active-switch converter (such as Class-E converter), the number of passive components in the resonant converter can be limited to four. Therefore, the power density of the system can be improved drastically. In this paper, a 100-W prototype is presented under the experimental condition to validate the proposed integrated-stage LED driver. [ABSTRACT FROM AUTHOR]

In this paper, a series-capacitor-based interleaving buck power factor correction (PFC) converter is proposed, the intermediate energy storage capacitance of which is operated at discontinuous capacitor voltage mode (DCVM), and automatic power factor (PF) correction for this converter is obtained. Moreover, the voltage across the series capacitor of the proposed PFC converter is clamped at the input voltage, and thus peak voltage stress existed in the traditional DCVM buck PFC could be relieved. By effectively regulating the charge/discharge time for the series capacitor, ultrahigh step-down conversion ratio of the proposed converter is achieved, the conversion ratio of which is independent of the duty cycle and only related to the switching frequency and circuit parameters. Therefore, high PF can be obtained due to very narrow deadtime of the input current. Meanwhile, the proposed PFC converter can realize the soft turn-on of part power switch and soft turn-off of part power diodes. In addition, comparing with the traditional discontinuous inductor current mode PFC, the input current of the proposed PFC converter is continuous so that the peak value and root-mean-square value of input current can be reduced. The operational principle, performance analysis, and parameter design principle are given in this paper. The analysis results show that the PF and total harmonic distortion are also independent of the duty cycle. Finally, a 220-Vac input, 60 W/15 V output experimental prototype is built to verify the validity of the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper proposes a new dc–ac converter with a reduced number of semiconductor switches and gate drive and control circuit components. A salient feature of this inverter is its pure sinusoidal line-to-line voltages with no need for output filter. Also, the proposed inverter improves the voltage utilization factor of the input dc supply compared to the four-switch three-phase inverter (first best topology in the literature from the number of switches point of view) and standard six-switch inverter with sine pulsewidth modulation. The proposed inverter is capable of operating with a wide range of output voltages from zero to the full value of the dc input voltage by appropriately altering the instantaneous duty cycle. A three-phase universal inverter with only three power switch has been proposed in this paper for the first time ever, to our knowledge. For the purpose of providing a good compromise between fast transient response and stability, a model predictive controller is proposed. All the design expressions have been derived. A comparison with other dc–ac converters is given to show the merits of the proposed converter. Finally, satisfactory circuit operation is confirmed by experimental results from a laboratory prototype. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high step-down dc–dc converter with ultrahigh step-down conversion ratio is proposed. Advantages of the proposed converter are high step-down ratio, extended duty cycle, reduced switching losses by a converter operation under zero-voltage switching (ZVS) conditions, reduced reverse reco-very losses of diodes by achieved zero-current switching turn-off condition, and reduced voltage spikes by the inherent active-clamping structure of the converter. In this converter, series capacitors and coupled inductors have been used in power path to achieve the low voltage gain and extended duty cycle. By the inherent active-clamping structure of the proposed converter, the leakage inductance energy is totally recovered in the output; therefore, the high voltage spike across the semiconductor devices is suppressed. The switches of the proposed converter can operate under ZVS conditions, which cause reduced switching losses and improved efficiency. In this paper, the converter operating modes are discussed, and a prototype circuit is implemented. Experimental results are presented to verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

A new isolated single-stage soft-switching power-factor-correction (S4 PFC) driver for supplying light-emitting diodes (LEDs) is introduced in this paper. In the proposed LED driver, the switches voltage stress and also the dc-bus voltage is limited to the peak of the line voltage. Hence, low voltage rated mosfets and diodes can be used. The efficiency is improved because the switches are turned on under zero current switching (ZCS) condition and turned off under zero voltage zero current switching (ZVZCS) condition. Also, no current feedback is required since the converter provides an output current independent of output voltage. In this paper, operating principle of the proposed LED driver is presented and design considerations are discussed. To verify the theoretical analysis, a laboratory prototype of the proposed converter for supplying a 50 W/70 V LED module from 220 Vrms/50 Hz ac mains is implemented, and the experimental results are presented. Since current feedback is not used, dimming property and operation for universal voltage range is not achievable. [ABSTRACT FROM PUBLISHER]

In this paper, new half-bridge and full-bridge topologies for a switched-boost inverter are proposed. These topologies have a high boost factor in comparison with conventional types. In addition, the proposed topologies have continuous input current and can generate zero-voltage level in output. In this paper, the operation of the proposed inverters in different operating modes is analyzed. Then, the values of inductors and capacitors are designed. Moreover, the used switching pattern and its logical diagram are introduced. A comprehensive comparison between the proposed and conventional topologies in terms of the boost factor, the number of elements, and the efficiency shows the good features of the proposed inverters. Finally, to verify correct operation of the proposed topologies and derived equations, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

The development of a high static gain dc–dc converter with the integration of the voltage multiplier cell and the coupled inductors operating with soft switching is presented in this paper. The use of coupled inductors and voltage multiplier techniques allow the operation with low switch voltage and low conduction losses. The switch turn-on commutation occurs with zero current switching due to the presence of the coupled-inductor leakage inductance. The leakage inductance also reduces the reverse recovery current of all diodes. The zero voltage switching at the power switch turn-off is obtained with the inclusion of only a diode and a snubber capacitor per phase, without the use of auxiliary switches. The soft-switching range is independent of the load and is maintained even with a light load. The theoretical analysis, design procedure, and experimental results are presented in this paper. A two-phase boost converter with one voltage multiplier and coupling inductors was built with an input voltage $V_{{\text{in}}}= { \text{24 V}}, output voltage Vo= { \text{432 V}}, and output power Po= { \text{400 W}}. The efficiency obtained is equal to 94.55% at the nominal power. [ABSTRACT FROM PUBLISHER]

In this paper, a nonisolated dc–dc converter with high voltage gain is presented. Three diodes, three capacitors, an inductor, and a coupled inductor are employed in the presented converter. Since the inductor is connected to the input, the low input current ripple is achieved, which is important for tracking maximum power point of photovoltaic panels. The voltage stress across switch S is clamped by diode D 1 and capacitor C1. Therefore, a main switch with low on-resistance RDS (on) can be employed to reduce the conduction loss. Besides, the main switch is turned on under zero current. This reduces the switching loss. The steady-state analysis of the proposed converter is discussed in this paper. Finally, the proposed converter prototype circuit is implemented to justify the validity of the analysis. [ABSTRACT FROM PUBLISHER]

This paper presents three unidirectional step-up ac–dc converter topologies with voltage multiplication on their outputs. The first topology is the hybrid boost rectifier and the other two are novel bridgeless structures, all based on the integration of boost rectifier and the ladder switched-capacitor (SC) cell. The new hybrid structures provide high voltage gain with low voltage stress across the switches, high-power factor, and output voltage regulation. This paper presents the principle of operation, steady-state and dynamic analysis, design methodology, and experimental verification. A different approach is also presented for the design methodology of the SC cell and for the analysis of its influence on the dynamic model. Three 1000-W prototypes with a 220-V input voltage, 800-V output voltage, and 100-kHz switching frequency were designed to corroborate the theoretical study. The best efficiency was 97.1$\%$ in the proposed bridgeless versions and the voltage stress across the switches stands around 400 V. Furthermore, a comparison between the proposed structures and previous topologies is also presented. [ABSTRACT FROM PUBLISHER]

This paper proposes a wide-range zero-voltage-switching (ZVS) active-clamped current-fed push–pull converter for fuel cell application. The presented converter achieves ZVS for all of the primary switches and ZCS for secondary diodes from rated load to 10% full load over the wide input voltage variation, improving the overall efficiency. The ZVS of switches is realized by the energy stored in the transformer leakage inductance aided by the secondary parallel inductor. An additional active clamping circuit suppresses the voltage spike as well as assists in realizing ZVS of switches. Low-voltage-rated switches with low on-state resistance can be used. Moreover, the voltage-doubler rectifier is adopted to release the reverse-recovery problem of rectifier diodes and reduce turns ratio of the high-frequency transformer. Detailed steady-state operation, analysis, design, control, comparative study, and experimental results are discussed in depth in this paper. Finally, a 200-W prototype has been built in the laboratory to verify the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, two topologies are presented for the enhanced-boost quasi-Z-source inverters (qZSI), namely continuous input current configuration and discontinuous input current configuration of enhanced-boost qZSI with two-switched impedance networks. Similar to enhanced-boost impedance-source inverters (ZSIs), these proposed inverter topologies possess very high boost voltage inversion at low shoot-through duty ratio and high modulation index to provide an improved quality output voltage. Compared to enhanced-boost ZSIs with two-switched Z-source impedance networks, these proposed inverter topologies share common ground with source and bridge inverter, overcome the starting inrush problem, and draw continuous input current and the lower voltage across the capacitors. Moreover, the input ripple current is negligible. This paper presents the operating principles and analysis of continuous input current configuration enhanced-boost qZSI with two-switched impedance networks and compares with ZSI, switched inductor ZSI, DA/CA-qZSI, and enhanced-boost ZSIs. The theoretical analysis is done and is validated through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes a family of soft-switching bidirectional converters. In many applications, the bidirectional converters operate over a wide range of duty cycle and load variations. In the proposed converters, in order to extend the zero-voltage switching operation range, two supplemental voltage sources utilizing passive components are implemented in the auxiliary circuit. By using this method, the soft-switching features are ensured for an extensive range of the converter duty cycles. This is achieved independent of the output power value or the converter operation mode, and so, soft switching is ensured within the entire converter operating region. In these converters, all semiconductors components are soft switched, and the auxiliary circuit does not contribute to the complexity of the control circuit. Also, no extra voltage stress exists on the main switches and the voltage stress on the auxiliary switches is lower than the main switches voltage stress. In this paper, the proposed bidirectional buck/boost converter is analyzed and to confirm the feasibility of the proposed method, experimental results of a 150-W prototype converter are presented. [ABSTRACT FROM PUBLISHER]

This paper introduces the bridgeless triple-mode resonant ac–dc converter and presents its dynamic model and control technique. The proposed converter operates in triple mode: discontinuous-conduction mode (DCM), continuous-conduction mode (CCM), and missing resonance mode (MRM). It has the advantages of small number of required components, medium power capacity, and high efficiency, but it is difficult to control because DCM, CCM, and MRM have their own dynamic characteristics. To solve this control problem, the mode boundaries are first identified and, corresponding to each mode, the dynamic model is developed to design the controller. In each mode, we propose to add a repetitive controller (RC) with a phase-lead compensator to the conventional duty ratio plus feedback controller. The RC is used to suppress the deterministic periodic disturbances and the phase-lead compensator is used to compensate for the incurred phase lag. A 1-kW digitally controlled converter prototype is built and used to demonstrate the validity of the proposed modeling and control approach. [ABSTRACT FROM AUTHOR]

A soft-switched nonisolated high step-up dc–dc converter based on the quasi-impedance-source structure is presented in this paper. In the proposed converter, a technique similar to the synchronous rectifier is applied such that the diode of the impedance network is replaced with an active switch. In this way, not only is conduction loss associated with the diode reduced but also zero-voltage-switching characteristics for power switches are provided. Also, output diodes of the proposed converter are switched under zero-voltage-zero-current-switching condition which extremely reduces their switching and reverse-recovery losses. It is shown that by correct design of the components, soft-switching performance is retained for all the semiconductor devices over the entire range of output load. All these factors together with simplicity of the proposed structure result in high efficiency over a wide range of output power. Moreover, the proposed converter benefits from continuous input current and a shared ground between input and output. Operating principles of the proposed converter along with its steady-state analysis are presented. Also, experimental results obtained from a laboratory prototype for 48 to 350 V voltage conversion and 100 W nominal power are provided to validate the feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper introduces a novel single-phase buck–boost noninverting variable-frequency ac–ac converter that offers higher efficiency compared to the competitors. This converter utilizes a lower number of semiconductors. A simple and flexible switching strategy is also proposed, which generates the desired output waveform avoiding unnecessary high-frequency switching operation of semiconductor devices. A high reliable operation due to the elimination of the input source shoot-through risk, an inherent commutation capability that mitigates the voltage spikes across the semiconductors, a lower semiconductors rating requirement, an improved input current waveform quality, and a smaller required input filter inductor are the main advantages of the proposed converter. Thus, the proposed converter can be successfully applied to many industrial applications such as medium-frequency transformer isolation for traction and wind turbine converters, ac–dc high-voltage conversion based on Cockcroft–Walton circuit and induction heating systems. The theoretical achievements and claims are all confirmed through extensive experimental tests on a 200-W laboratory setup. [ABSTRACT FROM AUTHOR]

In this paper, eight ultrahigh-voltage gain dc–dc converters are proposed. These sets of converters are derived by the association of boost cells, coupled inductor, voltage multiplier, switched capacitors, and LC filter cells. The nonpulsating input and output converters are evaluated in terms of: principle of operation, voltage gain, voltage and current stress, estimated power losses, and efficiency. Following full analysis prototypes built in the laboratory show experimental results verifying the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, closed-loop control and boundary condition for continuous conduction mode and discontinuous conduction mode of nonisolated inverting N× multilevel boost converter (MBC) are articulated. Inverting N× MBC combines the features of classical boost converter and voltage multiplier to attain inverting N times higher voltage. Consequently, the inverting N× MBC provides a viable solution for high-voltage step-up photovoltaic applications with low voltage rating reactive components and semiconductor devices. The control strategy with saturation limiter is employed to achieve highly stable voltage. The modes of operation, benefits of inverting N× MBC, and key factors for the selection of semiconductor devices and sizing of the reactive components are discussed. Additionally, the effects of reactive components and semiconductor devices on the output voltage are examined. Experimental results of the developed circuit are presented to validate the design of converter, and effectiveness and robustness of the implemented control algorithm for different input and output side perturbations. [ABSTRACT FROM AUTHOR]

In this paper, a voltage sensorless controller is developed for a two-switch single-phase rectifier that involves power factor correction and active pulsating power buffering without electrolytic capacitors. While a two-switch rectifier normally requires four sensed signals for control, only one current sensor is required in this proposal, thereby offering advantages such as low cost, high compactness, isolation between control and power circuits, and improved reliability. While the basic operating principle follows that of a conventional voltage sensorless controller for single-switch converters, several critical design considerations are the key to the success of the implementation which is explained in detail. The feasibilities of the controller are experimentally testified with a 100-W rectifier prototype regarding both steady state and dynamic performance. [ABSTRACT FROM AUTHOR]

In this paper, a new transformerless buck–boost converter based on a ZETA converter is introduced. The proposed converter has the ZETA converter advantages, such as buck–boost capability, input-to-output dc insulation, and continuous output current. The suggested converter voltage gain is higher than the classic ZETA converter. In the presented converter, only one main switch is utilized. The proposed converter offers low voltage stress of the switch; therefore, the low on-state resistance of the main switch can be selected to decrease the losses of the switch. The presented converter topology is simple; hence, the control of the converter is simple. The converter has the continuous output current. The mathematical analyses of the presented converter are given. The experimental results confirm the correctness of the analysis. [ABSTRACT FROM AUTHOR]

Circuit analysis and design criteria of a two-phase bidirectional converter with high voltage gain are presented in this paper. The operating principle of the forward or reverse mode is similar to that of the conventional buck or boost converter. Compared with the conventional converter, the switch stresses can be reduced significantly depending on the operating region of the voltage ratio in the two-phase converter. The power losses can also be reduced due to the use of low-voltage rating switches. The derivate converters are discussed to demonstrate the advantages of the proposed topology. A 200 W/1 MHz two-phase prototype converter with gallium nitride (GaN) devices is built and tested to verify the feasibility. [ABSTRACT FROM AUTHOR]

In this paper, the design methodology of switched-tank converter (STC) is presented. The power loss breakdown analysis is conducted to point out the directions and paths for components optimization. It is revealed that the switching device conduction loss, printed circuit board (PCB) loss, and inductor loss become significant when output power is >150 W. Power loss of four switches is calculated and compared for switching device selection. The resonant capacitor is carefully designed to meet both current stress and ripple requirements. On the other hand, optimal design of the resonant inductors and PCB layout are fully investigated. The core loss model is provided, and different core materials are compared to minimize the core loss. Besides, a fine-tuned inductor winding structure is designed to achieve the lowest winding loss. Furthermore, PCB layout is optimized to get short loop length for each operation state. In addition to the hardware level optimization, an improved control method is proposed, in which the conduction time of switching devices is tuned to mitigate the circulating power. To verify the optimization work, a prototype of STC is built and tested. The experimental results indicate that a state-of-the-art performance of 98.71% efficiency and a 1000 W/in3 high power density is achieved. [ABSTRACT FROM AUTHOR]

For photovoltaic applications, the flyback microinverter with pseudo-dc-link is popular as a simple topology but brings large transformer turns ratio and thus large leakage inductance, which would deteriorate the converter efficiency. To solve this issue, based on the nonisolated pseudo-dc-link structure, this paper proposed a hybrid boost–flyback/flyback (BF/F) microinverter. This new topology is operated at the BF mode for the most segment of a half grid cycle and the F mode for the rest. During the BF mode, high voltage gain with low voltage stress is easily available in minimized transformer turns ratio. Besides, the leakage energy is recycled and the turn-off voltage spike of the main switch is clamped, as a result of a passive snubber inherently contained in this mode. Given that the BF mode is lack of step-down function, the F mode is developed to regulate the output voltage even for values lower than the input voltage. The operation and characteristic of the hybrid BF/F microinverter in boundary conduction mode are analyzed in detail, and the mathematical expression of reference current is derived theoretically to guarantee high power quality. Finally, a 240 W prototype was implemented to validate the theoretical analysis and the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper presents a new highly integrable hybrid step-down converter that merges switched-inductor and switched-capacitor operations and significantly reduces onboard loss by using the input cable's parasitic inductance as its main inductor. This converter has the inductor placed at the input with a smaller voltage swing, leading to possible use of a smaller inductor and low-voltage rating switches that generally translate to reduced conduction losses. Analyses of converter operation and losses to reveal its original characteristics and design guidelines are presented to facilitate the components optimization. The converter architecture is verified by a proof-of-concept 15-W inductor-less lithium-ion battery charger prototype that uses a 1-m USB 3.0 cable as inductor. The converter, switched at 2 MHz from a 5-V input, experimentally achieves 89.7% peak efficiency and 6% higher efficiency at full load than a Buck converter counterpart. This high efficiency and zero onboard inductor yield a relative 45.7% onboard loss reduction at full load, promising excellent integration feasibility and superior system thermal management. [ABSTRACT FROM AUTHOR]

This paper proposes a novel isolated high step-down conversion circuit, called an integrated buck and modified push−pull (IBMPP) converter, which is able to lower the voltage level on the primary side of the ideal transformer, resulting in a lower turns-ratio and decreased leakage inductance. The IBMPP converter is able to prevent the duty cycle from operating in extremely low conditions. Furthermore, the proposed converter adopts active-clamp techniques to recycle leakage energy and to suppress voltage spikes, so that the conversion efficiency can be effectively improved. The advantages of the IBMPP converter are its simple topology, easy control mechanism (which requires only two signals with a 180-degree phase shift), high conversion ratio, low component counts for power switches, and less voltage stress on some of the switches on the high-voltage side. The operation principle, steady-state analysis, design considerations, and experimental results of the proposed IBMPP converter are presented in detail. The feasibility of the IBMPP is verified by hardware implementation. The full-load efficiency at 250 W is 81.44%, and the input and output voltages are 380 and 5 V, respectively. [ABSTRACT FROM AUTHOR]

In this paper, a new high voltage gain step-up dc–dc converter is proposed for interfacing renewable power generation. The configuration optimally integrates both the coupled-inductor and switched-capacitor techniques to achieve an ultra-high step-up gain of voltage conversion with low voltage stress and high efficiency. It consists of a voltage boost unit, a passive clamp circuit, and a symmetrical voltage multiplier network. The structure becomes modular and extendable without adding any extra winding for ultra-high step-up voltage gain. The proposed topology not only reduces the voltage stress on the main switch but also maintains it steady for the entire duty cycle range. Furthermore, the reverse recovery issue of the diodes is alleviated through the leakage inductance of the coupled inductor. The operation principle and steady-state analysis are presented in detail. Experimental evaluation validates the claimed advantages and demonstrates a well-distributed efficiency curve and the peak of 96.70%. [ABSTRACT FROM AUTHOR]

This paper presents a novel switch current stress reduction technique for a single switch boost-flyback high step up dc–dc converter. Coupled inductor-based converters do not have a sufficiently higher inductance value of their windings. This creates current surge during transient and steady state, which in turn increases current stress at main switch. To compensate this difficulty in coupled inductor-based boost flyback converter, an inductor–diode parallel combination has been connected in series with the switch. This technique increases the effective inductance of the coupled inductor primary winding during switch turn-on operation and helps to reduce current stress. Steady-state operating principle with the proposed technique is analyzed in continuous conduction mode. The current reduction technique is discussed with a proper mathematical derivation. To verify theoretical findings, simulation study is carried out in MATLAB/Simulink R2014b. Finally, a laboratory-based 40-W prototype converter is designed to show the effectiveness of the proposed switch current reduction technique. [ABSTRACT FROM AUTHOR]

A new transformerless bidirectional buck-boost converter is proposed in this paper. The proposed converter has a simple circuit structure, low component count, low voltage stress on the power transistors, and a wide voltage gain range. This makes it applicable in the energy storage charge/discharge systems, such as electric vehicles (EV), microgrids and nanogrids with energy storage units, and uninterruptible power supplies. In addition, synchronous rectification between the complementary transistors is employed to improve the converter efficiency. A comprehensive analysis of the steady-state operation, small-signal model, component parameters design, and efficiency analysis of the proposed converter operating in a continuous conduction mode is given. Finally, a 1.6-kW scaled-down prototype was built using Silicon Carbide MOSFETS to validate the effectiveness and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, a novel noncoupled inductor high voltage gain single-ended primary-inductor converter (SEPIC) is presented. The proposed converter has various advantages, such as lower voltage stress on the switches, noninverting output voltage, high efficiency, and high voltage gain. Also, the introduced converter has a continuous input current which makes it suitable for renewable energy and fuel cell applications. Moreover, high voltage gain is achieved without using any transformer and coupled inductor, thus there is not any voltage overshoot for the switches during the turn-off process. This effect allows low conduction losses by using lower voltage rating switches and also additional clamping circuit is not needed. The control system of the presented converter is simple and the converter can be easily controlled in continuous conduction mode mode operation. Because, the gating pulses for both of the switches are the same and wide output voltage range is achieved only by changing the duty cycle. Furthermore, the number of the components compared to the other noncoupled inductor, SEPIC-based converters which provide near voltage gain to the proposed converter, is reduced. The detailed operation of the introduced converter and design considerations are discussed. Experimental results are presented to verify the performance of the proposed dc–dc converter. [ABSTRACT FROM AUTHOR]

The magnetic resonant wireless power transfer (WPT) system with a class E inverter has wide application in mid-range power transmission, especially for several megahertz scenario. However, it is cumbersome for the existing modeling and analysis methods to obtain the analytical solution to the system variables, which limits the evaluation of system characteristic. This paper proposes a nonlinear mathematical model for the WPT system with a class E inverter. The equivalent small parameter method (ESPM) is first adopted to solve the proposed six-order nonlinear model, and symbolic-form steady-state periodic solutions are yielded. During the whole solving process, only three iteration steps are needed for the proposed method. Compared with other existing modeling and analysis methods, the symbolic periodic results acquired by the ESPM exhibit sufficient accuracy by virtue of the combination of more higher harmonics. Meanwhile, the calculation complexity is simplified remarkably. Simulation and available experiments validate the effectiveness and accuracy of the proposed method. [ABSTRACT FROM AUTHOR]

In this paper, a fully soft-switched bidirectional dc–dc converter is proposed. All semiconductor devices are soft switched, while its control circuit remains pulsewidth modulated. This condition is achieved only by one auxiliary switch. So, the proposed topology has less complexity in comparison with other similar structures. The energy conversion through the proposed topology during buck and boost modes is highly efficient due to achieved soft-switching condition. The auxiliary circuit operates once during each switching cycle. The converter is analyzed and a 250-W laboratory prototype of the proposed converter is constructed. The experimental results are presented that confirm the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, a generalized switching modification method is proposed to reduce the root-mean-square (rms) current flowing into a dc-link capacitor in a dc–dc–ac structure consisting of a boost converter and a three-phase inverter. To analyze the current flowing into the capacitor, we analyze the currents at the respective converter and inverter sides. Based on this analysis, we derive an analytical method to find the modification time between the converter and inverter pulsewidth modulation (PWM) carriers through a Fourier series and approximation to facilitate real-time implementation. Real-time implementation of the modification time calculated by the derived method is described. To verify the validity of the proposed method, experimental results are presented based on a 1-kVA dc–dc–ac prototype. The proposed method has a better capacitor rms current reduction performance than the conventional method in various inverter power factors and PWM strategies. Especially, it has an excellent performance in mid-power factor level (0.95–0.1). [ABSTRACT FROM AUTHOR]

This paper proposes two coupled-inductors-based Z-source networks, called the modified series and tapped switched-coupled-inductors quasi-Z-source networks (mSSCL-qZSN and mTSCL-qZSN, respectively). These networks offer high voltage gains with less-than-unity winding turn ratios $(n < {\text{1)}}$ , resulting in a reduced inductive element size. Other advantages include a less number of active components and their lower ratings and a higher efficiency. In addition, a lower magnetic core size is required for the proposed ZSNs due to the lower peak magnetizing current. The performance principles and detailed comparative analysis are provided and confirmed through experiments on a 200-W dc–dc converter. [ABSTRACT FROM AUTHOR]

Condition monitoring of aluminum electrolytic capacitors (AECs) is essential for predictive maintenance of power electronic converters. The AEC is considered at the end of its life when its capacitance or equivalent series resistance (ESR) reaches corresponding critical values. In the literature, it is found that either of these parameters may reach its critical limit depending on the operating conditions and applications. However, most of the existing health monitoring techniques of the AEC in dc–dc converters are based on the estimation of ESR. To address the aforementioned issue, this paper proposes to estimate the low-frequency impedance of the AEC, which is dominated by its capacitance value, thereby allowing health monitoring based on the capacitance value. The technique is based on injection of a low-frequency current ripple into the AEC using duty ratio control of the dc–dc converter. The parameters of new and aged capacitors are experimentally obtained at various temperatures and are used to establish the failure criteria. Furthermore, the proposed method is applicable for both the continuous conduction mode and the discontinuous conduction mode (DCM) of operation. For DCM operation, a sampling instant to recover a low-frequency waveform is suggested based on mathematical analysis. Detailed simulation studies are performed and results are included in this paper. Experimentation is carried out on a dc–dc boost converter integrating solar photovoltaic with the dc system. Experimental results are found to be in agreement with simulation results. [ABSTRACT FROM PUBLISHER]

In this paper, a new soft switching flyback dc–dc converter with a simple zero-voltage and zero-current switching (ZVZCS) cell is proposed. The auxiliary resonant cell consists of one switch, one diode, one inductor, and two capacitors. It provides ZVZCS not only for the main switch but also for the auxiliary switch at both turn-on and turn-off times. In addition, all the auxiliary diodes and body diodes of the switches operate under full ZVZCS except the output diode which turns off only with zero current switching. This soft switching technique makes the proposed converter have less switching losses which leads the converter to operate in higher frequencies and efficiency. Another outstanding feature of the proposed converter is using the auxiliary resonant cell out of the main power path to have lower voltage stress on the switches. In this paper, pulse width modulation (PWM) is employed to control the main switch. A detailed mode analysis of the proposed converter operation is presented along with design procedure. Finally, the accuracy performance of the converter is verified through a 60 W experimental prototype results. [ABSTRACT FROM AUTHOR]

In this paper, a new topology for half-bridge Z-source inverter is proposed. The proposed topology has only one impedance network. Unlike to the conventional half-bridge inverter, the proposed topology can provide zero voltage level at the output. It also increases output voltage level and stabilizes it in the desired value. Capacitor voltage stress in the proposed topology is low, and, therefore, nominal voltage of capacitor and cost decreases. In this paper, the steady-state analysis of the proposed inverter in two new operations which are named synchronous operation of diodes and asynchronous operation of diodes is conducted based on mathematics calculations. A method to obtain high-voltage gains by cascading the Z-network and combining middle inductors is presented that leads to cost, size, and weight reduction. Comparison among the proposed converter with conventional ones shows its excellent performance. The experimental results have good agreement with analytical analysis for the proposed topology. [ABSTRACT FROM PUBLISHER]

In this paper, a nonisolated bidirectional dc–dc converter is presented. The proposed converter consists of two boost converters to enhance the voltage gain. Four power switches with their body diodes are employed in the proposed converter. Also, two inductors and a capacitor are used as passive components. The input current is divided to the inductors which causes the efficiency to be high. The voltage gain of the proposed converter is higher than the conventional cascaded bidirectional buck/boost converter (CCBC) in step-up mode. Besides, the voltage gain in step-down mode is lower than CCBC. Besides, the efficiency of the proposed converter more than CCBC while the total stress on active switches are same. The simple structure of the proposed converter causes its control to be easy. The steady-state analysis of the proposed converter is discussed in this paper thoroughly. The stress on converters’ devices and the efficiency of the proposed converter and CCBC are compared in this paper. Finally, the proposed converter prototype circuit is implemented to justify the validity of the analysis. [ABSTRACT FROM PUBLISHER]

In this paper, a new multi-input multi-output (MIMO) dc–dc converter with high step-up capability is proposed for wide power ranges. Also, in order to increase each output voltage, diode–capacitor voltage multiplier (VM) stages are utilized in the proposed converter. The number of input stages, output stages, and VM stages are arbitrary and dependent on design conditions. At first, the general structure of proposed MIMO converter is presented. Then, in order to explain the converter operation, we walk through the design of a 1-kW four-input two-output example, including loss and efficiency calculations. We validate the design with a prototype that matches efficiency calculations. [ABSTRACT FROM AUTHOR]

The interleaved bidirectional buck–boost converter dual active half-bridge (IBBC-DAHB) dc–dc converter consists of two converters IBBC and DAHB and a coupled inductor. The IBBC-DAHB converter has significant features such as low ripple current at the low-voltage side, low current stress on the input inductors, voltage stress across the switches less than the high-voltage side, high voltage gain, and zero-voltage soft switching. The converter offers high efficiency using phase-shift modulation when it operates at a nominal design operating point. However, the efficiency decreases due to high circulating current, high current stress, and limited soft-switching range when the source and load voltages deviate from their nominal values. This paper employs both duty cycle and phase-shift modulation methods to improve the above mentioned shortcomings using voltage matching for the DAHB converter. The proposed converter is analyzed and a 500-W experimental prototype with 40–60 V input voltage and 400 V output voltage under 100 kHz switching frequency is implemented to verify the theoretical results. The maximum efficiency of 97.15% is achieved at 60 V and 400 W. A flat efficiency characteristic for the converter is derived by the proposed control method, where the efficiency at 20% of nominal load is 91% and much higher than the phase-shift control, which is 70.8%. [ABSTRACT FROM AUTHOR]

In this paper, an input-series flyback converter with the coupled-inductor-based passive snubber is proposed, where the input-series converter is based on transformer integration, and the passive snubber is composed of inductors, capacitors, and diodes. The inductors of the snubber in various series modules are made on a common magnetic core, and the coupled-inductor scheme is adopted. With the help of the coupled inductor, active input voltage sharing of the input-series converter can also be achieved after the switches are turned off, and voltage sharing of the switch in each series module can be ensured, which overcome the shortcomings of the existing input-series flyback converter. Active voltage sharing processes caused by the coupled inductor are analyzed in detail. Furthermore, the design guideline of the passive snubber is discussed. Finally, the experimental study has been done on a 1500 Vdc/60 W laboratory-made prototype composed of three flyback series modules, and the feasibility of the proposed method and the theoretical analysis is verified by the experimental results. [ABSTRACT FROM AUTHOR]

In this paper, an expandable single-input three-output high step-up dc–dc boost converter is proposed. The voltage conversion ratio of the output ports of the converter can be increased by inductor-diode-capacitor and diode-capacitor cells. The proposed converter can be applied in renewable energy conversion systems, such as in photovoltaic and fuel cells. Also, due to the three output ports of the converter, it can be utilized in portable devices which require high voltage conversions. The main advantage of the proposed converter is supplying loads with different voltages and current ranges due to the expandable structure of the converter. Besides, the proposed converter has the merit of achieving high voltage gains at high frequencies without preselecting wide duty cycles. Furthermore, the proposed converter is able to achieve higher voltage ranges without having any transformer or coupled inductors in its structure; consequently, the related drawbacks are avoided. The switching pattern of the converter is simple and both switches are on and off simultaneously. In this study, a single switching period of the proposed converter, the voltage conversion ratios of the output ports and the expanded form of the structure are analyzed theoretically. Finally, to verify the theoretical results, the experimental results for 40-V input/200-V, 100-V and 360-V outputs with total 600-W output power are extracted and compared with each other. [ABSTRACT FROM AUTHOR]

Due to the pulsating power at the inverter output terminals, the passive storage elements of the boost stage of the current-fed switched inverter (CFSI) contain a power frequency harmonic component (100 Hz), apart from dc and switching frequency components. In prior designs, the second harmonic component is suppressed by increasing the size of the input filter inductor and capacitor or by using additional circuits. This paper presents a complete characterization of a control-based approach to suppress the power frequency harmonic component in the input inductor current of a CFSI. It also presents a comprehensive characterization of the harmonic power redistribution. Using the proposed approach, it is demonstrated that the inductor value of a CFSI is reduced by 61% for the same peak-to-peak ripple. This leads to an improvement in the conversion ratio, efficiency, and power density of the overall converter. A SiC MOSFET-based CFSI with 75-kHz switching frequency is used to verify the proposed design philosophy. [ABSTRACT FROM AUTHOR]

In this paper, a high step up converter consisting of an integrated quadratic-boost converter and a voltage doubler is proposed. The integration of the quadratic-boost converter makes the system easier to lift up its voltage gain through slightly increasing the duty ratio of the single switch. The voltage doubler further increases the voltage gain of the system as the turn ratio rises. The voltage stresses on the switch and the diodes are decreased for such cascaded topology. Different operation modes are analyzed and mathematical analysis of the converter is presented in detail. The leakage inductance contributes to realizing zero current switching of the diodes in the second boost stage and the doubler and the energy can be recycled to the load. A 38-W prototype is built to work as a vehicle LED driver. Experiments are conducted to verify the advantages of the proposed converter and the efficiency is 90% at the nominal operating point. [ABSTRACT FROM AUTHOR]

In recent years, modular multilevel converter (MMC) is considered for medium-voltage variable speed drives (VSD) due to its modularity and higher reliability. However, the major drawback of the MMC-based VSD is the higher capacitor ripple voltage at lower operating speeds. In literature, this ripple voltage is reduced by injecting a high-frequency circulating current into each arm. This additional circulating current increases the overall current rating of the devices, inductors, and capacitors. Alternatively, the capacitor ripple voltage can be reduced at the lower output frequency by reducing the dc-bus voltage. This paper proposes a new configuration using a multipulse diode-bridge rectifier to reduce the dc-bus voltage when the drive is operated at lower speeds. Therefore, the capacitor ripple voltage decreases without injecting any circulating current. In addition, a new technique is proposed to maintain the peak-to-peak value of the submodule capacitor ripple voltage constant at near-zero speed. The proposed converter with 24-pulse rectifier configuration is simulated in MATLAB/Simulink, and the experimental validation is carried out on a prototype with 12-pulse rectifier. [ABSTRACT FROM AUTHOR]

In this paper, a new modified single-switch single-ended primary inductor converter (MS2-SEPIC)-based high step-up dc–dc converter is presented. The proposed topology uses the coupled-inductor (CL) technique and a voltage tripler rectifier, which results in a high voltage gain for the converter. Here, the switching loss has been reduced significantly owing to the quasi-resonance operation of the circuit created by the leakage inductance of the CL along with circuit capacitors. The operational principles and steady-state analysis are discussed. Experimental results based on a 100 W laboratory prototype verify the validity of theoretical analysis. [ABSTRACT FROM AUTHOR]

A 1-MHz-modified single-ended primary-inductor converter (SEPIC) circuit is presented in this paper as an LED driver for automotive headlights. On the basis of traditional SEPIC, only a diode and two capacitors are added; therefore, the circuit structure is relatively simple and the volume is relatively small. High step-up capability is obtained with moderate duty cycle. Compared with traditional step-up circuit such as boost, low-voltage stress is gained which is beneficial to device selection. Zero-voltage switching is achieved at the same time to reduce switching loss. Planar inductors are used with the advantages of low profile and good thermal characteristic. Operational principle and parameters design process are introduced in detail. A 36-W prototype has been designed to demonstrate theoretical analysis. Obtained efficiency was up to 90.91% at full load. [ABSTRACT FROM AUTHOR]

Switched-capacitor converter (SCC) featuring high efficiency and power density has attracted industry interest, but weak output voltage regulation hinders its application. This paper presents an optimized phase-shift (PS) control strategy for a bridge modular SCC, utilized in energy storage system, to obtain continuous conversion ratio and high-efficiency operation. By employing a small inductor as current buffer, the control strategy could be implemented to regulate output voltage conveniently with excellent steady and dynamic performance in step-down mode as well as step-up mode. Most importantly, the high-efficiency operation mechanism never reported before is revealed here. Correspondingly, the active circumfluence could be controlled through optimizing the range of PS time, which will avoid the loss in circuit self. Meanwhile, the soft-switching conditions of all the switches are comprehensively analyzed and soft-switching operations are achieved according to the logic timing control of the power devices, improving efficiency further. Finally, the prototype of the proposed converter was built and the experimental results validated the principle and features of the conversion method. [ABSTRACT FROM AUTHOR]

High step-up converters are required for distributed photovoltaic generation systems, due to the low voltage of the photovoltaic source. In this paper, a new hybrid high voltage gain dc–dc converter is created by merging the standard boost converter with a coupled inductor and different switched-capacitor techniques. With a single switch and no requirement of higher duty cycle values, the proposed converter achieves a high voltage gain and high efficiency, in addition to lowered voltage and current stresses of the components. A 200-W prototype was implemented experimentally to evaluate the converter, which reached a maximum efficiency of 97.6%. [ABSTRACT FROM AUTHOR]