Search

To balance the phase output currents of a multiphase inverter, negatively coupled inductors (NCIs) can be used to achieve a larger differential mode (DM) loop impedance than the common mode (CM) loop impedance. For a good current sharing effect, the inductances of the NCIs should be large, leading to bulky size and cost ineffectiveness, which should be avoided in high-power applications. This article proposes a novel current balancing method based on parallel resonance. A parallel resonant network (PRN) is inserted between any two phases. With $\Delta $ -Y transform, the inductor common point and the capacitor common point are generated, either of which can be used as the CM output node. For a series–series compensated wireless power transfer system, part of the existing compensating capacitance can be employed to form PRNs with the added parallel inductors. The DM currents are suppressed by the large impedance of the PRNs. Compared with the existing method, the inductances of the NCIs can be greatly reduced to achieve better current balancing performance. The added parallel inductors are of small current ratings, which are only visible to DM currents. A prototype is implemented to validate the proposed method. [ABSTRACT FROM AUTHOR]

In wireless power transfer (WPT) systems, the relative position between the transmitting and receiving coils could change suddenly, which is one of the most significant distinctions between wireless and wired power transfer systems. To the best of the authors’ knowledge, no theoretical analysis has been reported on the dynamic behavior of the WPT systems under the relative position transient (RPT). This article proposes the concept of “coupling-coefficient susceptibility” to describe this dynamic behavior. The extended describing function method is applied to extract the mathematical model of the coupling-coefficient susceptibility. Finally, an RPT testing platform, composed of a series-series compensated WPT system and a coil motion mechanism is designed and fabricated to verify the theoretical analysis. The experimental results exhibit a good agreement with the proposed model. [ABSTRACT FROM AUTHOR]

Free positioning wireless charging for consumer electronics allows the devices to be charged at arbitrary positions and angles to improve user experience. However, a user-initiated sudden movement of the device during charging can cause hazards due to the abrupt variation of the coupling coefficient. To solve this issue, the coupling coefficient variation at different positions should be mitigated, which is also good for the design and high-efficiency operation of power electronics converters. This article proposes a design methodology to employ antiparallel windings to smooth the coupling coefficient variation over different positions by reducing the coupling coefficient at central positions and enhancing it at boundary positions. Two optimization methods are proposed: turn-by-turn optimization and winding-by-winding optimization. A design flow is offered. The hexagonal coil is compared with the square coil and proved to achieve better performance than the latter. An experimental prototype is implemented to validate the effectiveness of the proposed design methodology. [ABSTRACT FROM AUTHOR]

To increase the power density of a wireless power transfer (WPT) system, the coupling of coils can be strong. However, in a strongly coupled series–series WPT system with a diode rectifier, currents can be distorted and discontinuous, and first harmonic approximation is no longer valid. The inverter is likely to work in hard switching, leading to extra noise, decreased efficiency, and a potential hazard for a safe operation. Through time-domain analysis, this article reveals that with a dual-side 90° phase shift, the hard switching of the inverter can be avoided, the power level can be enhanced, and the discontinuous conduction mode can be avoided to eliminate noises. The factors impacting the soft switching operations of the inverter and the rectifier are analyzed. To achieve 90° dual-side phase shift, the conventional approach of using the receiver voltage/current, which can be distorted and discontinuous in strongly coupled WPT systems, for phase synchronization is no longer suitable. A new set of coils, namely driving coils, is used for phase synchronization so that dual-side phase shift can be implemented independent from power transfer. Experimental results have validated the effectiveness of the analysis. [ABSTRACT FROM AUTHOR]

The extended describing function (EDF) method is widely used in modeling the resonant converters. This article finds that the model of the phase-shift controlled resonant converter deduced by this method might be inaccurate especially when the duty-cycle is close to 1. The reason behind it is investigated, showing that derivation of the inverter bridge model based on its fundamental harmonic will cause error. A novel model of the inverter bridge by Fourier analysis is proposed. Incorporating the novel model into the EDF-based resonant model, the accuracy of the phase-shift controlled resonant converter is greatly improved. A series–series compensated inductive power transfer system is fabricated in the lab to verify the validity of the proposed model. [ABSTRACT FROM AUTHOR]

The isolated feature between primary and secondary sides in wireless power transfer requires dual-side communication, phase synchronization, and two controllers on both sides. The phase difference between dual-side ac voltages can be changed for output regulation or bidirectional power flow. Zero crossing detection of the secondary ac voltage or current is normally conducted for frequency locking and phase synchronization. However, it is inaccurate at light-load conditions for high-power applications due to a large sensing scale and much noise; also, it can generate undesired results with discontinuous or distorted waveforms having more than two zero crossing points in one cycle. To solve these issues, this letter proposes a dual-side phase-shift implementation method using driving windings to regulate the dual-side phase difference conducted only on the primary side. By controlling the phase difference between the primary-side power and driving windings, the phase difference between the dual-side power windings can be regulated. In this way, the dual-side regulation is independent from power transfer to get rid of the issues of the conventional phase synchronization method, and bidirectional power flow can be more easily realized. [ABSTRACT FROM AUTHOR]

A wide operating region of inductive power transfer systems indicates a stable output against large load and coupling changes. In most of the published works, output regulation is achieved by single-side regulation that utilizes either primary-side or secondary-side power converters for load regulation. However, secondary-side regulation tends to have a relatively narrow operating region due to space and cost considerations. Meanwhile, although primary-side regulation may provide a larger operating region, system performance can be degraded due to the needs of secondary-side information. To overcome the drawbacks of single-side regulation, this article proposes a dual-side cooperative output regulation method implemented by burst-mode pulse density modulation. In the proposed method, dual-side cooperative control is established by sensing primary-side current drops caused by secondary-side burst operations and, hence, requires no communication devices. With the proposed method, the system operating region can be effectively extended without sacrificing steady-state performance. Experimental results are provided in this article to validate the proposed method. [ABSTRACT FROM AUTHOR]