Search

This paper proposes a capacitor voltage regulation method for the dual converter with a floating bridge for aerospace applications. This topology has previously been reported, but with a constrained voltage utilization factor due to the need for capacitor voltage regulations. In this paper, the effect of switching states on the voltage variation of capacitor is quantitatively modeled and an enhanced space vector modulation scheme with current feedback is proposed to achieve an active control of the floating capacitor voltages. This proposed method also allows further exploitation and utilization of converter voltage. The relationship between the allowed modulation index of dual converter and load power factor is obtained and expressed using a fitted polynomial equation. The advantages of the proposed method include boosted voltage utilization and superior performance in term of capacitor voltage balance. These advantages have been proven through simulation and experimental results on RL loads as well as with an open-end winding induction motor. The proposed modulation scheme can boost the converter voltage utilization by at least 10% while achieving full four-level operation. More importantly, the higher available voltage allows extending the constant torque region of the motor, the further beginning of field weakening operation could be postponed. [ABSTRACT FROM AUTHOR]

A trinary multilevel converter uses a few heterogeneous H-bridge submodules (SMs) to synthesize an output voltage with multiple levels. Two major limitations of this converter are that it needs multiple dc sources and it cannot operate under pulsewidth modulation (PWM). This paper addresses these limitations by adding a low-voltage H-bridge SM to this converter and proposing a new switching algorithm. The resulting PWM-based asymmetric cascaded H-bridge converter uses only one dc source and synthesizes a high-quality output voltage. This improved converter can be a potential choice for real and reactive power support in power system applications. This paper also proposes methods for stability analysis and design of this converter. Experimental case studies evaluate the performance of the proposed converter for both standalone and grid-connected modes of operation. [ABSTRACT FROM AUTHOR]

This paper presents two capacitor voltage balancing (CVB) strategies for modular multilevel converter (MMC) applications. Both balancing schemes are based on model predictive control and are designed to efficiently solve a constrained optimal control problem, where the predicted capacitor voltage errors are included in the cost function with the demanded output voltage of a cluster being forced through an equality constraint. The first method proposed in this paper computes specific modulation indexes for each module using the explicit solution of a relaxed version of the original optimization problem. The second approach proposed in this paper reduces the complexity of the original problem by linearizing the objective function and using an optimal sorting network based on a greedy algorithm to solve this approximation. Considering the structures of both solution approaches, they are integrated into modulation schemes based on phase-shifted and level-shifted pulsewidth modulation algorithms, respectively. Experimental results obtained from a nine-cell single-phase MMC prototype demonstrate the good performance achieved with the proposed methodologies, as well as the implementation simplicity offered by the proposed CVB algorithms. [ABSTRACT FROM AUTHOR]

This paper analyzes the combination in a cascaded H-bridge multilevel inverter (CHBI) based on transformers with the different turn ratios for increasing the voltage level and proposes the switching method for achieving the output voltage distribution among H-bridge cells (HBCs). The transformers used in this paper are connected to the output of the respective HBCs, and the secondary sides of all the transformers are connected in series for generating the final output voltage. Only one of the transformers, in particular, has a different turn ratio for increasing the output voltage level. In this paper, the possible turn ratio of the special transformer with a different turn ratio is discussed in detail, and a switching method based on the level-shifted switching method for the topology used in this paper is proposed. To verify the effectiveness of the proposed method, a three-phase 21-level CHBI is experimentally tested. [ABSTRACT FROM PUBLISHER]

This paper presents three unidirectional step-up ac–dc converter topologies with voltage multiplication on their outputs. The first topology is the hybrid boost rectifier and the other two are novel bridgeless structures, all based on the integration of boost rectifier and the ladder switched-capacitor (SC) cell. The new hybrid structures provide high voltage gain with low voltage stress across the switches, high-power factor, and output voltage regulation. This paper presents the principle of operation, steady-state and dynamic analysis, design methodology, and experimental verification. A different approach is also presented for the design methodology of the SC cell and for the analysis of its influence on the dynamic model. Three 1000-W prototypes with a 220-V input voltage, 800-V output voltage, and 100-kHz switching frequency were designed to corroborate the theoretical study. The best efficiency was 97.1$\%$ in the proposed bridgeless versions and the voltage stress across the switches stands around 400 V. Furthermore, a comparison between the proposed structures and previous topologies is also presented. [ABSTRACT FROM PUBLISHER]

This paper proposes an effective sliding mode controller (SMC) for a grid-connected 7-level packed U-cell (PUC7) inverter. The aim is to design a simple controller that deals effectively with the complex control problem of the PUC7 inverter (multiobjective control problem). The selection of the control actions is achieved according to the system state error at every sampling time, regardless of the previous values, which makes the control technique model-independent. The control algorithm evaluates online two cost functions (one for each state error), which are derived on the basis of sliding mode theory, and it selects the optimal control input in order to satisfy the reaching conditions of the two cost functions. Compared with the existing solutions, the proposed SMC technique ensures lower average switching frequency by tuning the hysteresis bandwidth of the capacitor-voltage error. The fast implementation, needless of gains tuning, and simple design procedure are the main features of the proposed algorithm. Simulation and experimental results are presented to prove the effectiveness of the proposed technique in controlling the PUC7 inverter with high dynamic performance and robustness against disturbances and parameters mismatch. [ABSTRACT FROM AUTHOR]

For photovoltaic applications, the flyback microinverter with pseudo-dc-link is popular as a simple topology but brings large transformer turns ratio and thus large leakage inductance, which would deteriorate the converter efficiency. To solve this issue, based on the nonisolated pseudo-dc-link structure, this paper proposed a hybrid boost–flyback/flyback (BF/F) microinverter. This new topology is operated at the BF mode for the most segment of a half grid cycle and the F mode for the rest. During the BF mode, high voltage gain with low voltage stress is easily available in minimized transformer turns ratio. Besides, the leakage energy is recycled and the turn-off voltage spike of the main switch is clamped, as a result of a passive snubber inherently contained in this mode. Given that the BF mode is lack of step-down function, the F mode is developed to regulate the output voltage even for values lower than the input voltage. The operation and characteristic of the hybrid BF/F microinverter in boundary conduction mode are analyzed in detail, and the mathematical expression of reference current is derived theoretically to guarantee high power quality. Finally, a 240 W prototype was implemented to validate the theoretical analysis and the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper presents an approach for dealing with the control of five-level, diode-clamped rectifiers. The control of such converters is challenging, as voltage balancing among capacitors is not a trivial task. Some of the existing approaches that cope with this problem use specific modifications of one of the traditional modulation techniques, such as using redundant vectors in space vector modulation (SVM). The main feature of the proposed technique is that part of the modulation is considered in the system equations and, in this way, the voltage balance can be solved designing a specific controller for this problem. As a result, several levels are used within a switching period. Furthermore, it is shown that the proposed approach hardly affects the control of active and reactive powers and total dc-link voltage in such a way that the well-known direct power control can be applied. As a consequence, the resultant modulation stage is simpler than other techniques based on, e.g., SVM. The effectiveness and good performance of the system under the proposed control approach are validated by both simulation and experimental results. [ABSTRACT FROM AUTHOR]

Zero-common-mode-voltage (CMV) operation of multilevel inverters results in reduced dc-bus utilization and reduced linear modulation range. In this paper, a method to increase the linear modulation range for zero-CMV operation without increasing the dc-bus voltage using a cascaded multilevel inverter with a single dc supply is presented. Using this method, the peak fundamental output voltage can be increased from 0.499 to 0.637  \textV\text{dc} with zero CMV inside the linear modulation range. Also, various pulse width modulation (PWM) switching sequences are analyzed in this paper, and the PWM sequence that gives minimum current ripple is used for the zero-CMV operation of the inverter. The inverter topology with single dc supply is realized by cascading a two-level inverter with two floating-capacitor-fed full-bridge modules. Simulation and experimental results for steady-state and dynamic operating conditions are presented to validate the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a model predictive control technique applied to a dual-active bridge inverter where one of the bridges is floating. The proposed floating bridge topology eliminates the need for isolation transformer in a dual inverter system and therefore reduces the size, weight, and losses in the system. To achieve multilevel output voltage waveforms, the floating inverter dc-link capacitor is charged to the half of the main dc-link voltage. A finite-set model predictive control technique is used to control the load current of the converter as well as the floating capacitor voltage. Model predictive control does not require any switching sequence design or complex switching time calculations as used for space vector modulation; thus, the technique has some advantages in this application. A detailed analysis of the converter as well as the predictive control strategy is given in this paper. Simulation and experimental results to validate the approach are also presented. [ABSTRACT FROM PUBLISHER]

This paper presents a three-phase open-end winding induction motor drive. The drive consists of a three-phase induction machine with open stator phase windings and dual-bridge inverter supplied from a single dc voltage source. To achieve multilevel output voltage waveforms, a floating capacitor bank is used for the second of the dual bridges. The capacitor voltage is regulated using redundant switching states at half of the main dc-link voltage. This particular voltage ratio (2:1) is used to create a multilevel output voltage waveform with three levels. A modified modulation scheme is used to improve the waveform quality of this dual inverter. This paper also compares the losses in the dual-inverter system in contrast with a single-sided three-level neutral point clamped converter. Finally, detailed simulation and experimental results are presented for the motor drive operating as an open-loop v /f controlled motor drive and as a closed-loop field-oriented motor controller. [ABSTRACT FROM PUBLISHER]

In this paper, a fixed switching frequency model predictive current controller is designed and implemented on a sensorless five-level packed U-cell (PUC5) inverter interfacing the utility. The predictive control methodology is based on a voltage vector generation technique for the cost function optimization by nullifying its derivative. The aim of the controller is to allow a fixed-frequency operation with no iterations while operating as a utility line current regulator. A pulsewidth modulator based on employing PUC5 redundant switching states fixes the PUC5 auxiliary dc bus capacitor voltage to its desired level with no necessity of a regulator; the overall technique reduces system complexity with less sensors and no loops in the predictive algorithm making it suitable for industrial applications. System discrete model is developed and experimental results verify the performance of the designed controller in making a fast response in regulating the grid current and balancing the capacitor voltage. [ABSTRACT FROM AUTHOR]

Switched-capacitor converter (SCC) featuring high efficiency and power density has attracted industry interest, but weak output voltage regulation hinders its application. This paper presents an optimized phase-shift (PS) control strategy for a bridge modular SCC, utilized in energy storage system, to obtain continuous conversion ratio and high-efficiency operation. By employing a small inductor as current buffer, the control strategy could be implemented to regulate output voltage conveniently with excellent steady and dynamic performance in step-down mode as well as step-up mode. Most importantly, the high-efficiency operation mechanism never reported before is revealed here. Correspondingly, the active circumfluence could be controlled through optimizing the range of PS time, which will avoid the loss in circuit self. Meanwhile, the soft-switching conditions of all the switches are comprehensively analyzed and soft-switching operations are achieved according to the logic timing control of the power devices, improving efficiency further. Finally, the prototype of the proposed converter was built and the experimental results validated the principle and features of the conversion method. [ABSTRACT FROM AUTHOR]

Discontinuous modulation applied to modular multilevel converters is an effective method for reducing the capacitor voltage ripples. In this paper, the discontinuous modulation is adapted and used in a motor drive application. For proper operation of the converter, a new energy controller is presented, which is suitable for operation with nonsinusoidal reference signals. Experimental results comparing the discontinuous modulation with other techniques operating at low motor speeds are shown. The results demonstrate the effectiveness of the discontinuous modulation on reducing capacitor voltage ripples and power losses. [ABSTRACT FROM AUTHOR]

This paper presents a modified modular multilevel converter with the three-terminal middle-cells inserted between arms and ac-side for medium voltage applications. It is intended to reduce the submodule capacitor voltage ripples by controlling the high-frequency powers flowing among arm branches for low-frequency output operations without common-mode voltage injected in ac-side. Due to the physical connection among the upper arm, the lower arm and ac-side, the middle-cell can be regarded as the excess degree of freedom to modify the dc-side and ac-side characteristics. Therefore, the common-mode voltage in ac-side can be eliminated by the inverse common-mode voltage produced by the middle-cell in ac-side. Moreover, owing to the unique structure of the middle-cell, the middle-cell capacitor voltage also results in a small ripple due to the high-frequency current flowing into it by proper control. The operation principle and control strategy of the middle-cell has been proposed in detail. Simulation and experimental results have verified the effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper proposes a novel 11-level improved active-neutral-point-clamped (11L-IANPC) converter for ground power unit (GPU) application. This hybrid topology consists of the 5L-ANPC and the proposed low-voltage submodule. The proposed 11L-IANPC converter possesses only one flying capacitor (FC) and reduced number of high-frequency switches. Hence, voltage diversity and ratings, stored energy, and the number of costly and bulky FCs are significantly decreased. Moreover, operating the augmented submodule at the low voltage and power leads to doubling the number of output voltage levels, whereas the low extra cost and size are imposed on the proposed converter. In addition, suggested sensorless switching method leads to self-balancing of FC and significantly amends the output voltage frequency spectrum. These improvements cause significant reduction in control complexity of the proposed 11L-IANPC converter, remarkable decrease in size of the bulky and costly output LC filter, and improving the dynamic and steady-state performance of the proposed static GPU. The simulation and experimental results validate the feasibility of the proposed converter as well as its suggested modulation and control method. [ABSTRACT FROM AUTHOR]

The conventional design of voltage-source power converters is based on a two-level half-bridge configuration and the selection of power devices designed to meet the full application specifications (voltage, current, etc.). This leads to the need to design and optimize a large number of different devices and their ancillary circuitry and prevents taking advantage from scale economies. This paper proposes a paradigm shift in the design of power converters through the use of a novel configurable device consisting on a matrix arrangement of highly optimized switching cells at a single voltage class. Each switching cell consists of a controlled switch with antiparallel diode together with a self-powered gate driver. By properly interconnecting the switching cells, the switching-cell array (SCA) can be configured as a multilevel active-clamped leg with a different number of levels. Thus, the SCA presents adjustable voltage and current ratings, according to the selected configuration. For maximum compactness, the SCA can be conceived to be only configurable by the device manufacturer upon the customer needs. For minimum cost, it can also be conceived to be configurable by the customer, leading to field-configurable SCAs. Experimental results of a 6 × 3 field-configurable SCA are provided to illustrate and validate this design approach. [ABSTRACT FROM AUTHOR]

Microinverters operating into the single-phase grid from new energy source with low-voltage output face the challenges of efficiency bottleneck and twice-line-frequency variation. This paper proposed a multilevel inverter based on bridge modular switched-capacitor (BMSC) circuits with its superiority in conversion efficiency and power density. The topology is composed of dc–dc and dc–ac stages with independent control for each stage, aiming to improve system stability and simplify the control method. The BMSC dc–dc stage, which can be expanded to synthesize more levels, not only features multilevel voltage gain but also partially replaces the original bulk input capacitor and functions as an active energy buffer to enhance power-decoupling ability between dc and ac sides. In dc–ac stage, the control strategy of optimized unipolar frequency doubling sine-wave pulse width modulation is proposed to improve the quality of output waveform. Meanwhile, the multilevel voltage phase has been optimized to further reduce the power loss. Finally, a prototype has been built and tested. Associated with the simulation, the experimental results validate the practicability of these analyses. [ABSTRACT FROM PUBLISHER]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes the combination of a novel modified quasi-Z-source (MqZS) inverter with a single-phase symmetrical hybrid three-level inverter in order to boost the inverter three-level output voltage. The proposed single-phase MqZS hybrid three-level inverter provides a higher boost ability and reduces the number of inductors in the source impedance, compared with both the single-phase three-level neural-point clamped quasi-Z-source inverter and the single-phase quasi-Z-source cascaded multilevel inverter. Additionally, it can be extended to obtain the nine-level output voltage by cascading two three-level pulse width modulation switching cells with a separate MqZS and a dc source, which herein is called a single-phase MqZS cascaded hybrid five-level inverter (MqZS-CHI). A modified modulation technique based on an alternative phase opposition disposition scheme is suggested to effectively control the shoot-through state for boosting the dc-link voltage and balancing the two series capacitor voltages of the MqZS. The performances of both the proposed MqZS-CHI and the modulation techniques are verified through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents a nine-level active-neutral-point-clamped (ANPC) based multilevel inverter (MLI) topology for grid-connected applications requiring only ten switches. The envisaged structure comprises two parts, namely five-level ANPC unit, and a two-level converter leg whose midpoint is used as another ac terminal. An ad hoc switching state redundancy based modulation strategy is used to ensure that the voltage across the flying capacitor is tightly balanced and is implemented using a look-up table further simplifies the control complexity. The performance and effectiveness of the proposed topology with its control scheme are validated through simulations and experimental tests. Comparison with other MLIs is included to highlight the merits of the proposed topology. From the results, it will be shown that the proposed inverter requires the least part count as compared to other topologies with the same performance and output quality. [ABSTRACT FROM PUBLISHER]

Cascaded H-bridge (CHB) multilevel inverters (MLIs) have been widely used for power electronics systems. While high-voltage blocking across power switches is not a constraint for low voltage applications, the research trend has been oriented to the design of more compact module topologies as an alternative for CHB. Despite the generation of more voltage levels with reduced switch count, the existing module topologies in recent literature take no account of the freewheeling current path during dead-time, thus, inducing multistep jumps in voltage levels and giving rise to undesirable voltage spikes. Addressing this concern, this paper proposes two symmetrical compact-module topologies for cascaded MLI, where freewheeling current path during dead-time is provided for smooth transition between voltage levels to prevent voltage spikes. The proposed 7-level and 13-level compact-modules demonstrated low number of conducting switches for all voltage levels. Comprehensive analysis and comparison with the latest module topologies are conducted. To validate the operation of the proposed compact-module topologies, simulation and experimental results are presented. [ABSTRACT FROM PUBLISHER]

This paper presents a modulation strategy for the modular multilevel converter (MMC) which provides the voltage balancing of the capacitors of different submodules comprising the converter. Not only is this modulation applicable to MMCs constructed with classic two level (2L) submodules, but it is also effective for arrangements with different submodule concepts, for instance, topologies like neutral point clamped (NPC), flying capacitors (FCs), neutral point piloted (NPP), etc. Therefore, firstly, the general modulation philosophy is explained applied to the two level (2L) submodule concept, and secondly, the extension to 3L-NPC and 3L-FC submodule topologies is analyzed. After that, the validation of the studied modulation strategy is carried out by means of successful simulation results, at different switching frequencies and number of submodules. The corresponding experimental results are shown in Part II of this paper after having implemented the aforementioned modulation strategy in a real test bench. In addition to this, a comparison based on thermal analysis and sizing of elements among the four studied submodule topologies is also included. [ABSTRACT FROM PUBLISHER]

This paper presents a novel soft-switching galvanically isolated buck-boost dc–dc converter as a module-integrated converter for photovoltaic (PV) applications. It features three major operating modes: boost, normal, and buck mode. Their proper distribution over the input voltage range enables wide voltage regulation capabilities, i.e., close to those of nonisolated power optimizers. The proposed control algorithm requires only one buck-boost switching stage that performs voltage regulation by means of the switching stage reconfiguration with smooth transition between the modes. The design guidelines and the digital control system for PV applications are provided. The module-integrated converter was verified experimentally with a solar array simulator. The converter showed good maximum power point tracking performance and a peak efficiency of nearly 97%. [ABSTRACT FROM PUBLISHER]

A microconverter serves as a front-end dc–dc stage of a microinverter to convert the power from a photovoltaic module to a dc bus. These front-end microconverters require isolation, high-boost ratio, wide-input voltage regulation, and high efficiency. This paper introduces an isolated resonant converter with hybrid modes of operation to achieve wide-input regulation while still maintaining high efficiency. The proposed converter is designed as a series resonant converter with nominal-input voltage and operates under two additional modes: a boost converter with low-input voltage and a buck converter with high-input voltage. Unlike conventional resonant converters, this converter operates at discontinues conduction mode with a fixed frequency, simplifying the design and control. In addition, this converter can achieve zero-voltage switching (ZVS) and/or zero-current switching (ZCS) of the primary-side MOSFETs, ZVS and/or ZCS of the secondary-side MOSFETs, and ZCS of output diodes under all operating conditions. Experimental results using a 300-W prototype achieve a peak efficiency of 98.1% and a California Energy Commission efficiency of 97.6% including all auxiliary and control power at nominal-input voltage. [ABSTRACT FROM PUBLISHER]

This paper presents a new active capacitor voltage balancing control method for the flying capacitor multicell (FCM) converters which is fully implemented using logic-form equations. The proposed active capacitor voltage balancing control technique, measures output current and flying capacitor (FC) voltages to generate the switching states in order to produce the required output voltage level and to balance FCs’ voltages at their reference values. Output voltage of the FCM converter controlled with proposed active capacitor voltage balancing method can be modulated with any pulse width modulation (PWM) technique such as the phase-shifted-carrier PWM or level-shifted-carrier PWM. An advantage of the proposed active capacitor voltage balancing control method is its simplicity as it does not require any complex computations and tedious optimization calculations. Simulation results and experimental measurements of a three-cell four-level and four-cell five-level FCM converters are presented to verify the performance of the proposed active capacitor voltage balancing control technique. [ABSTRACT FROM AUTHOR]

This paper proposes a novel active capacitor voltage balancing technique for stacked multicell (SM) converters. The proposed active capacitor voltage balancing control method detects the direction of the load current and measures the voltage of flying capacitors (FCs) to generate a proper switching state in order to form the required output voltage level and regulate the FC voltages at their desired reference levels. The proposed active capacitor voltage balancing control technique can modulate the output voltage through any of the pulse-width-modulation (PWM) techniques such as the phase-shifted carrier PWM or the level-shifted-carrier PWM. The foremost advantage of the proposed active control technique is that it does not demand any complex computations because it is not based on the optimization of the FC voltage-deviation cost functions. A thorough set of simulation results and experimental measurements for the five-level and seven-level SM converters are provided to validate the proposed active capacitor voltage balancing control method. [ABSTRACT FROM AUTHOR]

This paper presents a new multicell topology based on flying capacitor (FC) structure suitable for multilevel converters. The proposed topology employs the concept of phase-shifted carrier pulse width modulation (PWM) with modified modulating signals to generate appropriate PWM signals. The modulation strategy along with all possible switching states are explained. The implementation of the proposed PWM technique is shown by the help of illustrating waveforms. To show the advantages of the proposed structure, different performance criteria are compared with other FC multicell (FCM) structures. Simulation results are used to further evaluate the potential merits of the proposed topology. It is shown that the proposed structure is superior to other FCM-based structures from different standpoints. Specifically, it reduces the number of high-frequency switches, the number of FCs, and at the same time improves the quality of output voltage. A laboratory-type experimental setup is used to validate the modulation strategy and other theoretical findings. [ABSTRACT FROM AUTHOR]

A novel flying-capacitor-clamped five-level inverter based on bridge modular switched-capacitor topology is proposed in this paper. The inverter features the switched-capacitor circuit with dc–dc boosting conversion ability and the multilevel inverter circuit with flying-capacitor-clamped performance. With the special composite structure, the number of components is cut down compared to the topology of the conventional cascaded multilevel inverter. Meanwhile, part of switches can be operated under line voltage frequency, resulting in switching loss reduction. Hence, the potential of system efficiency and power density is released due to embed switched-capacitor circuit. More importantly, the optimized carrier-based phase disposition pulse width modulation method is employed as a control strategy. Under this control strategy, the capacitor voltage self-balance can be realized and quality of output waveforms can be improved significantly. After simulation, the prototype is built to validate the correctness and practicability of the analysis. [ABSTRACT FROM AUTHOR]

This paper presents a closed-loop space vector modulation (SVM)-based sliding mode controller (SMC) for a three-level grid-connected neutral point clamped (3L-NPC) inverter. The nonlinear SMC based on Gao's reaching law has been designed to control the grid current and inject desired amount of active and reactive power into the network. Due to using single dc source at the NPC inverter dc bus, neutral point voltage is controlled through redundant switching states and instantaneous dc voltage feedback integrated into SVM technique. Meanwhile, there is no external voltage controller involved, thus no associated fine tuning issues are existed. The performance of the proposed hybrid controller to inject a desired active/reactive power to the grid is investigated through external perturbations such as change in the line current amplitude/phase shift, ac voltage fluctuation, as well as dc voltage variation. Full converter state-space model was developed and simulated. Experimental results are provided to verify the fast dynamic performance, low content of line current THD%, and good voltage balancing of dc bus capacitors of the NPC inverter. [ABSTRACT FROM AUTHOR]

In this paper, a novel topology of six-level inverters for a medium-voltage high-power applications is proposed, which consists of inner flying-capacitor inverter (FCI) units and outer two-level inverter units. The proposed topology can reduce the number of devices, components, and isolated sources compared with the existing ones in the case of the same number of output voltage steps, which result in a reduction of the size and weight of the inverters. Also, the total power loss of the proposed topology is lower than that of the diode-clamped inverter (DCI) and FCI. Besides, the estimated cost of the proposed topology is about 60.5% and 81.3% compared with the DCI and FCI, respectively. In addition, the modulation technique and the control strategy for the dc-link capacitor and flying-capacitor voltages are developed for the proposed topology. The effectiveness of the proposed six-level inverter for the medium-voltage applications has been verified by simulation results. Also, the feasibility of the proposed inverter has been proved by experimental results for the prototype at the laboratory. [ABSTRACT FROM AUTHOR]

This paper presents a finite-control-set model predictive control (FCS-MPC) for grid-tied packed U cells (PUC) multilevel inverter (MLI). The system under study consists of a single-phase 3-cells PUC inverter connected to the grid through filtering inductor. The proposed competitive topology allows the generation of 7-level output voltage with reduction of passive and active components compared to the conventional MLIs. The aim of the proposed FCS-MPC technique is to achieve, under various operating conditions, grid-tied current injection with unity power factor and low total harmonic distortion while balancing the capacitor voltage. Parameters’ sensitivity analysis was also conducted. The study is conducted on a low-power case study single-phase 3-cells PUC inverter and with possible extension to higher number of cells. Theoretical analysis, simulation, and experimental results are presented and compared. [ABSTRACT FROM AUTHOR]

In this paper, a novel cascaded seven-level inverter topology with a single input source integrating switched-capacitor techniques is presented. Compared with the traditional cascade multilevel inverter, the proposed topology replaces all the separate dc sources with capacitors, leaving only one H-bridge cell with a real dc voltage source and only adds two charging switches. The capacitor charging circuit contains only power switches, so that the capacitor charging time is independent of the load. The capacitor voltage can be controlled at a desired level without complex voltage control algorithm and only use the most common carrier phase-shifted sinusoidal pulse width modulation strategy. The operation principle and the charging–discharging characteristic analysis are discussed in detail. A 1-kW experimental prototype is built and tested to verify the feasibility and effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper presents a new family of buck type power factor corrector rectifiers that operates in continuous-conduction mode (CCM) and generates a multilevel voltage waveform at the input. Due to CCM operation, commonly used ac-side capacitive filter and dc-side inductive filter are removed from the proposed modified packed U-cell rectifier structure. Dual dc output terminals are provided to have a five-level voltage waveform at the input points of the rectifier where it is supplied by a grid via a line inductor. Producing different voltage levels reduces the voltage harmonics which affects the grid current harmonic contents directly. Low switching frequency of the proposed rectifier is a distinguished characteristic among other buck type rectifiers that reduces switching losses and any high switching frequency related issues, significantly. The proposed transformerless, reduced filter, and multilevel rectifier topology has been investigated experimentally to validate the good dynamic performance in generating and regulating dual 125-V dc outputs terminals as telecommunication boards feeders or industrial battery chargers under various situation including change in the loads and change in the main grid voltage amplitude. [ABSTRACT FROM PUBLISHER]

For cascaded multilevel inverter topologies with a single dc supply, closed-loop capacitor voltage control is necessary for proper operation. This paper presents zero and reduced common-mode voltage (CMV) operation of a hybrid cascaded multilevel inverter with predictive capacitor voltage control. Each phase of the inverter is realized by cascading two- three-level flying capacitor inverters with a half-bridge module in between. For the presented inverter topology, there are redundant switching states for each inverter voltage levels. By using these switching state redundancies, for every sampling instant, a cost function is evaluated based on the predicted capacitor voltages for each phase. The switching state that minimizes cost function is treated as the best and is switched for that sampling instant. The inverter operates with zero CMV for a modulation index upto 86%. For modulation indices from 86% to 96%, the inverter can operate with reduced CMV magnitude (Vdc/18) and reduced CMV switching frequency using the new space-vector pulsewidth modulation (SVPWM) presented herein. As a result, the linear modulation range is increased to 96% as compared to 86% for zero CMV operation. Simulation and experimental results are presented for the inverter topology for various steady state and transient operating conditions by running an induction motor drive with open loop $V/f$ control scheme. [ABSTRACT FROM PUBLISHER]

In this paper, a model-predictive control (MPC) has been designed and implemented on the packed U-cell (PUC) inverter, which has one isolated dc source and one capacitor as an auxiliary dc link. The MPC is designed to regulate the capacitor voltage at the desired magnitude to have seven voltage levels at the output of the inverter. Since grid-connected application is targeted by this application, the inverter should be capable of supplying requested amount of active and reactive power at the point of common coupling (PCC) as well. Therefore, MPC should also consider the line-current control to monitor the exchange of reactive power with the grid while injecting appropriate active power at low total harmonic distortion (THD). Various experimental tests including change in dc-source voltage, active power variation, and operation at different power factor (PF) have been performed on a laboratory prototype to validate the good performance obtained by the proposed MPC. The dynamic performance of the controller during sudden changes in dc capacitor voltage, supply current, and PF demonstrates the fast and accurate response and the superior operation of the proposed controller. [ABSTRACT FROM PUBLISHER]

In this paper, a novel grid-connected high step-up inverter is proposed. The topology is composed of two stages. The first stage is a single-switch high step-up dc–dc converter with bipolar outputs, and the second stage is a conventional half-bridge dc–ac grid-connected inverter. Negative grounding of the photovoltaic (PV) module has resulted in elimination of unwanted ground leakage currents in the PV system. Simple structure, employing few semiconductor switches, simple control, and high efficiency are the features of the proposed topology. Theoretical analysis and principal operation of the circuit are discussed. An experimental prototype is implemented to verify the performance of the proposed inverter. The experimental results confirm the aforementioned features and the theoretical analysis of the converter operation. [ABSTRACT FROM PUBLISHER]

A novel complementary phase disposition pulsewidth modulation method for the modular multilevel converter (MMC) with a limited number of submodules is proposed in this paper. Compared with the previous works, more practical issues have been considered, and the corresponding solutions have been provided. First, a new preset PWM signal mapping sequence and an improved virtual loop mapping (VLM) are used in the modulation. This method not only achieves a favorable capacitor voltage balance in the symmetry system but lowers the switching frequency of MMC's devices. Second, to further reduce the switching frequency, the unbalance margin of capacitor voltages is adopted to achieve the switching between the VLM and the selective VLM (SVLM). Moreover, the system robustness has been improved by considering the situation of symmetry losing, like cell fails; in these cases, the capacitor voltages of the upper and lower arms are balanced through the collaboration of the SVLM and the reconfigurable VLM. Finally, the effectiveness of the proposed method has been verified with simulation and experimental studies. [ABSTRACT FROM AUTHOR]

This paper analyzes the interleaved boost with coupled inductors (IBCI) converter, which is an isolated topology that is suitable for high step-up applications. Two main contributions are given: an exhaustive steady-state analysis and an accurate small-signal model. The former allows for deriving a closed-form noniterative design procedure for the power-stage active and passive components. In addition, it reveals an interesting equivalence with an apparently different converter, i.e., the single active bridge. Subsequently, the IBCI converter dynamic behavior is investigated, deriving a nonlinear average model that, under small-signal approximation, can be linearized around a given operating point and used for feedback controller design. A single photovoltaic module interface converter, rated for 300-W output power, is considered as a case study to validate the analysis outcome and the design procedure. Both are fully validated by measurements taken on the laboratory prototype. [ABSTRACT FROM PUBLISHER]

This paper presents a capacitor voltage balancing control applicable to any multilevel dc–ac converter formed by a single set of series-connected capacitors implementing the dc link and semiconductor devices, such as the diode-clamped topology. The control is defined for any number of dc-link voltage levels and converter legs (for single-phase and multiphase systems), guaranteeing the capacitor voltage control for any modulation index value and load (from idle mode to full power). The associated control loop small-signal transfer function is presented, from which optimum compensator design guidelines are derived. The improvement in control performance is verified through simulation and experiments comparing with a previous balancing control strategy in a four-level three-phase dc–ac conversion system. The satisfactory control performance is also verified through simulation in a four-level five-phase dc–ac conversion system. [ABSTRACT FROM PUBLISHER]

This paper presents input-series–output-parallel (ISOP) configuration for single-phase front-end buck rectifiers (BRs). The configuration is especially suitable for traction applications, where the complete rectification system needs to withstand high ac voltages and supply medium-power loads. The primary rectification module of the proposed configuration is based on pulsewidth-modulated BR (current source inverter topology). The desired isolation, mandatory for ISOP connection, is provided at the dc stage through a medium-frequency/high-frequency transformer. Equal power sharing by modules is achieved from the ac side through input voltage and current sharing. The proposed control scheme is configured using two loops. While the outer loop regulates the output dc voltage and active wave shaping of the source current, the inner loop ensures stable voltage sharing. The performance of the proposed ISOP configuration is verified using numerical simulation. Experimental verification is achieved through a 2-kW grid-connected laboratory prototype. [ABSTRACT FROM PUBLISHER]

In a photovoltaic (PV)- or fuel-cell-based grid-connected power system, a high step-up dc–dc converter is required to boost the low voltage of a PV or fuel cell to a relatively high bus voltage for the downstream dc–ac grid-connected inverter. To integrate the advantages of the high voltage gain of a switched-capacitor (SC) converter and excellent output regulation of a switching-mode dc–dc converter, a method of combining the two types of converters is proposed in this paper. The basic idea is that when the switch is turned on, the inductor is charged, and the capacitors are connected in series to supply the load, and when the switch is turned off, the inductor releases energy to charge multiple capacitors in parallel, whose voltages are controlled by a pulsewidth modulation technique. Thus, a high voltage gain of the dc–dc converter can be obtained with good regulation. Based on this principle, a series of new topologies are derived, and the operating principles and voltage gains of the proposed converters are analyzed. Finally, the design of the proposed converter is given, and the experiment results are provided to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

In this paper, two new topologies are proposed for multilevel inverters. The proposed topologies consist of a combination of the conventional series and the switched capacitor inverter units. The proposed topologies reduce the number of switches and isolated dc voltage sources, the variety of the dc voltage source values, and the size and cost of the system in comparison with the conventional topologies. In addition, the proposed topologies can double the input voltage without a transformer. There is no need for complicated methods to balance the capacitor voltage. The simulation and experimental results of single-phase 25- and 17-level inverters are given to prove the correct operation of the proposed topologies. [ABSTRACT FROM PUBLISHER]

This paper presents a single-phase transformerless grid-connected photovoltaic converter based on two cascaded full bridges with different dc-link voltages. The converter can synthesize up to nine voltage levels with a single dc bus, since one of the full bridges is supplied by a flying capacitor. The multilevel output reduces harmonic distortion and electromagnetic interference. A suitable switching strategy is employed to regulate the flying-capacitor voltage, improve the efficiency (most devices switch at the grid frequency), and minimize the common-mode leakage current with the help of a novel dedicated circuit (transient circuit). Simulations and experiments confirm the feasibility and good performance of the proposed converter. [ABSTRACT FROM PUBLISHER]

This paper unifies the underlying concepts of all basic single-switch, two-state, dc-to-dc voltage-sourced converters, by duality, as generic related current and voltage-sourced converters. By using ac and dc circuit theory, the three basic converters can be transformed to yield all known transfer functions and realizes a proliferation of 33 topologies, three being previously unidentified topologies with unique characteristics. The circuit based systematic unifying approach offers new insight and an alternative interpretation to the origin of the 33 topologies including the Zeta, Cuk, \pmLuo, CSC, Landsman, and Sepic converters. Converter time-domain simulations and corresponding practical results of the three new topologies extol and culminate the concepts and analysis presented. [ABSTRACT FROM PUBLISHER]

This paper proposes the pulsewidth modulation (PWM) strategy of Z-source inverters (ZSIs) with minimum inductor current ripple. In existing PWM strategy with single-phase shoot-through, the shoot-through time interval is divided into six equal parts, therefore the three phase legs bear the equal shoot-through time interval. In this manner, the allotment and arrangement of the shoot-through state is easy to realize, but the inductor current ripple is not optimized. This causes to use relatively large inductors. In the proposed PWM strategy, the shoot-through time intervals of three phase legs are calculated and rearranged according to the active state and zero state time intervals to achieve the minimum current ripple across the Z-source inductor, while maintaining the same total shoot-through time interval. The principle of the proposed PWM strategy is analyzed in detail, and the comparison of current ripple under the traditional and proposed PWM strategy is given. Simulation and experimental results on the series ZSI are shown to verify the analysis. [ABSTRACT FROM PUBLISHER]

This paper presents the hybrid seven-level cascaded active neutral-point-clamped (ANPC)-based multilevel converter. The converter topology is the cascaded connection of a three-level ANPC converter and an H-bridge per phase. The voltage of the H-bridge is actively maintained to the required level through selection of the switching states of the converter. The topology is operated under selective harmonic elimination pulsewidth modulation (SHE-PWM), maintaining the switching frequency of the converter to a minimum. The operating principles, voltage balancing methods, and limitations of the converter are analyzed together with extensive simulation results of the topology. Experimental results from a low-power laboratory prototype are presented that verify the operation of the hybrid converter under SHE-PWM. [ABSTRACT FROM PUBLISHER]

A new scheme for nine-level voltage space-vector generation for medium-voltage induction motor (IM) drives with open-end stator winding is presented in this paper. The proposed nine-level power converter topology consists of two conventional three-phase two-level voltage source inverters powered by isolated dc sources and six floating-capacitor-connected H-bridges. The H-bridge capacitor voltages are effectively maintained at the required asymmetrical levels by employing a space vector modulation (SVPWM) based control strategy. An interesting feature of this topology is its ability to function in five- or three-level mode, in the entire modulation range, at full-power rating, in the event of any failure in the H -bridges. This feature significantly improves the reliability of the proposed drive system. Each leg of the three-phase two-level inverters used in this topology switches only for a half cycle of the reference voltage waveform. Hence, the effective switching frequency is reduced by half, resulting in switching loss reduction in high-voltage devices. The transient as well as the steady-state performance of the proposed nine-level inverter-fed IM drive system is experimentally verified in the entire modulation range including the overmodulation region. [ABSTRACT FROM PUBLISHER]

Power converters consisting of naturally commutated thyristors such as cycloconverters and current source inverters were the first to be used in driving electrical motors with variable speed, but now, due to their inferior performance compared to forced commutated converters, their use is restricted in the high voltage/high power range where the performance and cost of forced commutated switching devices are not yet competitive. Hybrid cycloconverters proposed recently are capable of improving the performance of cycloconverters by adding an auxiliary forced commutated inverter with reduced installed power. It will be shown that the new topology is not only able to improve the quality of the output voltage but is also able to enhance the control over the circulating current and, therefore, for some of the cycloconverter arrangements, to improve the input power quality. This paper evaluates the performance of a few standard and hybrid cycloconverter arrangements using both simulation and experimental results. [ABSTRACT FROM AUTHOR]

A novel three-phase diode boost rectifier is proposed in this paper. The core of the proposed topology is a power conversion device [the loss-free transformer (LFT)] with two terminals; one input and one output. The input is parallel-connected with the dc bus capacitor, while the output is connected between the rectifier plus rail and the dc bus plus rail. The LFT is controlled in such a way to control the rectifier current and boost the dc bus voltage. In contrast to the ordinary boost rectifiers, the switches of the new boost rectifier are rated on a fraction of the dc bus voltage and a fraction of the input current. It makes this topology very compact and efficient. Power rating, size, and losses depend strongly on the ratio of the dc bus voltage to rectifier voltage (boosting factor). For example, if the boosting factor is low, below 1.5, the power converter efficiency could be 98–99%. The proposed boost rectifier has been analyzed and experimentally verified on a 5.5-kW prototype. The results are presented and discussed. [ABSTRACT FROM AUTHOR]