Search

This paper presents a finite-control-set model predictive control (FCS-MPC) for grid-tied packed U cells (PUC) multilevel inverter (MLI). The system under study consists of a single-phase 3-cells PUC inverter connected to the grid through filtering inductor. The proposed competitive topology allows the generation of 7-level output voltage with reduction of passive and active components compared to the conventional MLIs. The aim of the proposed FCS-MPC technique is to achieve, under various operating conditions, grid-tied current injection with unity power factor and low total harmonic distortion while balancing the capacitor voltage. Parameters’ sensitivity analysis was also conducted. The study is conducted on a low-power case study single-phase 3-cells PUC inverter and with possible extension to higher number of cells. Theoretical analysis, simulation, and experimental results are presented and compared. [ABSTRACT FROM AUTHOR]

In this paper, a novel cascaded seven-level inverter topology with a single input source integrating switched-capacitor techniques is presented. Compared with the traditional cascade multilevel inverter, the proposed topology replaces all the separate dc sources with capacitors, leaving only one H-bridge cell with a real dc voltage source and only adds two charging switches. The capacitor charging circuit contains only power switches, so that the capacitor charging time is independent of the load. The capacitor voltage can be controlled at a desired level without complex voltage control algorithm and only use the most common carrier phase-shifted sinusoidal pulse width modulation strategy. The operation principle and the charging–discharging characteristic analysis are discussed in detail. A 1-kW experimental prototype is built and tested to verify the feasibility and effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

The performance of Voltage Source Inverter (VSI) is affected by power semiconductor nonlinearities, dead time, and control delay. The compensation of these nonlinear effects is necessary to meet requirements in terms of current quality and high efficiency, especially for grid-connected power conversion systems. In this paper, the effects of nonlinearities are widely analyzed and a new compensation technique for a steady-state current-controlled VSI is proposed. It is based on a step-by-step voltage compensation on the basis of the current error evaluated within each control interval. As a result, a complete compensation is achieved within a whole period of the fundamental. To cope with the zero-current clamping effect, the proposed compensation technique is implemented in a recursive way. For slow-dynamic applications, such as photovoltaic systems, this method allows achieving high performance with very low computational requirements. [ABSTRACT FROM PUBLISHER]

For cascaded multilevel inverter topologies with a single dc supply, closed-loop capacitor voltage control is necessary for proper operation. This paper presents zero and reduced common-mode voltage (CMV) operation of a hybrid cascaded multilevel inverter with predictive capacitor voltage control. Each phase of the inverter is realized by cascading two- three-level flying capacitor inverters with a half-bridge module in between. For the presented inverter topology, there are redundant switching states for each inverter voltage levels. By using these switching state redundancies, for every sampling instant, a cost function is evaluated based on the predicted capacitor voltages for each phase. The switching state that minimizes cost function is treated as the best and is switched for that sampling instant. The inverter operates with zero CMV for a modulation index upto 86%. For modulation indices from 86% to 96%, the inverter can operate with reduced CMV magnitude (Vdc/18) and reduced CMV switching frequency using the new space-vector pulsewidth modulation (SVPWM) presented herein. As a result, the linear modulation range is increased to 96% as compared to 86% for zero CMV operation. Simulation and experimental results are presented for the inverter topology for various steady state and transient operating conditions by running an induction motor drive with open loop $V/f$ control scheme. [ABSTRACT FROM PUBLISHER]

This paper proposes a unified PWM method for matrix converters so as to establish a common platform which can generate various types of PWM methods in real time by adjusting the free parameters in the modulation algorithm. As a foundation for unification, the general form of the modulation functions for matrix converters is derived using geometric transformation approach. All eligible direct modulation matrices are shown to be of indirect form and are expressed in terms of instantaneous phase quantities. This paper also presents a new viewpoint to consider a matrix converter as a generalized three-level inverter and to apply the double-carrier-based dipolar modulation technique of the three-level inverter to the matrix converter. Several concepts of the two-level PWM inverters are then generalized to the matrix converters for better visualization and understanding of the modulation process. [ABSTRACT FROM AUTHOR]

This paper proposes a new space-vector pulsewidth modulation (SV-PWM) strategy for a three-level neutral point clamped inverter. The presented SV-PWM strategy makes it possible to control the neutral point voltage by optimum choice of switch sequence for any position and length of output voltage vector. The proposed solution takes into consideration the unbalance of the dc-link voltages. It also analyzes the influence of vector sequences on the predicted unbalance of the dc-link voltage. The solution allows selecting optimum vectors and their on-time durations in order to reduce quickly the dc-link voltage unbalance. The calculation of the space vector area proposed in this paper takes into consideration voltage unbalance and its influence on the length and position of vectors. The proposed approach assures properly generating the voltage output vectors, even in the case of the existing large voltage unbalance in the dc-link. The results of the experimental investigation of the proposed modulation strategy are presented in this paper. [ABSTRACT FROM PUBLISHER]

AC–DC–AC converter-fed induction motor (IM) drive is mainly realized by back-to-back three-phase converters. However, fault in a single semiconductor switch will make it inoperative. To enable continued controllable operation in case of the faults occurring in the converter, the five-leg converter with a shared leg between the grid and load sides is a possible solution. However, this topology poses an inherent two-objective control problem, because its grid and load sides should be controlled simultaneously. More importantly, the potential increase of the shared-leg current may destroy the converters. In this paper, a new control scheme based on the FCS-MPC combined with intrinsic characteristic of the five-leg converter is proposed for independent control of the rectifier and inverter subsystem with the shared-leg overcurrent constraint. The condition for independent control is analyzed. In order to give a complete evaluation of the proposed control scheme, the conventional pulsewidth modulation (PWM) control scheme is conducted for comparison. Experimental results are provided to validate the effectiveness of the proposed scheme. [ABSTRACT FROM PUBLISHER]

In this paper, a model-predictive control (MPC) has been designed and implemented on the packed U-cell (PUC) inverter, which has one isolated dc source and one capacitor as an auxiliary dc link. The MPC is designed to regulate the capacitor voltage at the desired magnitude to have seven voltage levels at the output of the inverter. Since grid-connected application is targeted by this application, the inverter should be capable of supplying requested amount of active and reactive power at the point of common coupling (PCC) as well. Therefore, MPC should also consider the line-current control to monitor the exchange of reactive power with the grid while injecting appropriate active power at low total harmonic distortion (THD). Various experimental tests including change in dc-source voltage, active power variation, and operation at different power factor (PF) have been performed on a laboratory prototype to validate the good performance obtained by the proposed MPC. The dynamic performance of the controller during sudden changes in dc capacitor voltage, supply current, and PF demonstrates the fast and accurate response and the superior operation of the proposed controller. [ABSTRACT FROM PUBLISHER]

Modular multilevel converter (MMC) is a promising new topology for high-voltage applications. The MMC is made of several identical submodules. For proper operation, each submodule can be considered as a controlled voltage source where capacitor’s voltage should be maintained at a certain level. Besides, the minimization of the circulating current, which does not flow to the load, is crucial for achieving stable and efficient operation of the MMC. The interrelations among the load current, circulating current, and capacitor voltages complicate the MMC control. This paper aims to achieve stable and balanced voltage and current control with reduced circulating current in various operating conditions. The proposed control uses weighted model predictive control based on a normalized cost function to select the inverter switching patterns, which control the load current, while minimizing voltage fluctuation and circulating current. The weighting factors were selected based on minimizing the load-current total harmonic distortion (THD) and circulating current. The analysis is conducted on a low-power case study of single-phase four-cells MMC with possible extension to higher number of cells. The low-power three-level prototype is designed and built to validate this proposed method. Theoretical analysis, simulation, and experimental results are presented and compared. Parameter sensitivity analysis was also conducted. They all confirm the effectiveness of the proposed control method. [ABSTRACT FROM PUBLISHER]

The cost reduction of power-electronic devices, the increase in their reliability, efficiency, and power capability, and lower development times, together with more demanding application requirements, has driven the development of several new inverter topologies recently introduced in the industry, particularly medium-voltage converters. New more complex inverter topologies and new application fields come along with additional control challenges, such as voltage imbalances, power-quality issues, higher efficiency needs, and fault-tolerant operation, which necessarily requires the parallel development of modulation schemes. Therefore, recently, there have been significant advances in the field of modulation of dc/ac converters, which conceptually has been dominated during the last several decades almost exclusively by classic pulse-width modulation (PWM) methods. This paper aims to concentrate and discuss the latest developments on this exciting technology, to provide insight on where the state-of-the-art stands today, and analyze the trends and challenges driving its future. [ABSTRACT FROM PUBLISHER]

The flying capacitor multilevel inverter (FCMLI) is one of the well-known structures of multilevel inverters having attracted considerable attention because of its merits. In spite of its many advantages, it has some limitations such as high volume and complicated control method because of its bulky capacitors and their voltage balancing requirement. Moreover, the high number of power semiconductors required makes this structure susceptible to failure. To increase the ratio of the number of levels to the number of components, an uneven distribution of capacitor voltages has been suggested in previous reports; however, this approach complicates the control method. Up to now, almost all presented methods suffer from high computational load and/or structure-dependent algorithm. In this paper, a simple state-based and structure-independent method is proposed for capacitor voltage regulation. The proposed method is straightforward and can perform online computation of switching sequences in a computationally efficient manner without any need for stored information or look-up tables. The method is conveniently extendible to any number of cells and levels in an FCMLI structure with arbitrary dc link voltage distribution schemes. Simulation and experimental results show the effectiveness and simplicity of this method. [ABSTRACT FROM PUBLISHER]

This paper presents proportional integral direct torque control (PIDTC) and fuzzy-2 DTC (F2DTC) of the induction motor (IM) drive using space vector pulse width modulation (SVPWM) for three-level diode-clamped inverter (TDCI). The above control schemes have been implemented in the laboratory using 2 HP IM through a DSPACE DS-1104 controller. The control schemes are capable to balance the dc-link capacitor voltages of TDCI by selecting an optimum voltage vector without using an extra controller. However, the three-level PIDTC of an IM gives poor transient performance during starting, loading, and speed reversal with considerable current and voltage total harmonic distortion (THD). In addition, it takes more time to reach the steady state with large spikes on capacitor voltages during the load or speed variation. This is due to poor performance of the PI controllers (speed and torque). In F2DTC, the conventional PI controllers are replaced by Mamdani-type fuzzy-2 controllers using a centroid method with simple logical rules. The simulated and experimental performance show that F2DTC for the three-level inverter-fed IM drive provides a fast dynamic response, less current and voltage THDs, considerable less distortion in flux and torque, and fewer spikes on capacitor voltages as compared to PIDTC. [ABSTRACT FROM PUBLISHER]

This paper describes a single-phase full-bridge inverter that possesses limited current ripple at the dc link while providing a sinusoidal square power at the ac output. This is achieved through the addition of an extra pair of switches and complementary control for the full-bridge inverter. The extra switches operate to prevent the double-line frequency ripple current from flowing into the input of the inverter. In doing so, the pulsation component of the sinusoidal square output power is confined to flow between the output capacitors and the load. Thus, the dc link input only supplies the dc component of the output power. Simulation and experimental results validating the proposed solution are presented. [ABSTRACT FROM PUBLISHER]

In this paper, a novel grid-connected high step-up inverter is proposed. The topology is composed of two stages. The first stage is a single-switch high step-up dc–dc converter with bipolar outputs, and the second stage is a conventional half-bridge dc–ac grid-connected inverter. Negative grounding of the photovoltaic (PV) module has resulted in elimination of unwanted ground leakage currents in the PV system. Simple structure, employing few semiconductor switches, simple control, and high efficiency are the features of the proposed topology. Theoretical analysis and principal operation of the circuit are discussed. An experimental prototype is implemented to verify the performance of the proposed inverter. The experimental results confirm the aforementioned features and the theoretical analysis of the converter operation. [ABSTRACT FROM PUBLISHER]

Carrier-based pulsewidth-modulation (CBPWM) techniques are popular due to their simplicity, and have been widely researched for various three-phase inverter configurations. In this paper, two CBPWM techniques are proposed to reduce the common-mode (CM) voltage generated by the five-phase inverter. The five-phase inverters have more flexibility in reducing the CM voltage than their three-phase counterparts because they have more phase legs, hence finer control over the star-point voltage of the load. Two methods are proposed for the conventional two-level five-phase inverter to reduce the CM voltage; one utilizing adjacent modulating waveforms and the other utilizing nonadjacent modulating waveforms. The coupled inductor inverter (CII) uses coupled inductors to generate multilevel outputs. As the volt-second balance must be maintained across each coupled inductor, direct application of the proposed methods on the CII inverter will result in overcurrents in the coupled inductors. Hence, the proposed methods are further improved to ensure the volt-second integral over each switching period is zero. Moreover, the two proposed methods are designed to reduce switching events and prevent unexpected states occurring during the switching transitions. The performance and the switching strategy of both methods are verified by both simulations and experiments on a prototype of five-phase CII. [ABSTRACT FROM AUTHOR]

In this paper, the two-input buck converter is proposed as the dc/dc stage for photovoltaic (PV) cascaded converters. This converter is attractive for this application because it is cost effective and reliable and can achieve dual maximum power point tracking (MPPT) with only one power transistor. However, due to the simplified and integrated structure, the nonlinear characteristics of the converter and the two PV arrays complicate the control. By means of a small-signal modeling, the control theme of the two PV voltages is formulated, and the effect of the nonlinearities is presented. It is shown that, while fast voltage dynamics are achieved for the first input, the second-input voltage response depends on the second-stage converter control. Simulation and experimental results are reported to validate the theoretical analysis, showing the dual MPPT capability. [ABSTRACT FROM PUBLISHER]

Local dc distribution systems or dc nanogrids for residential and commercial buildings are growing popular due to the increased focus on energy savings. Using low-voltage dc for the nanogrid provides various advantages such as easier integration with renewable sources and battery banks, increased savings, etc. Future systems would use renewable sources and storage devices to become self-sufficient in generation with bare minimum consumption from the grid. The objective of this paper is to develop an energy management system (EMS) to provide uninterrupted power supply to the dc loads and achieve self-sufficiency by minimizing grid power consumption. This is achieved by developing a control scheme for a cascaded two-stage bidirectional converter interface between the nanogrid and the ac distribution network. In addition, an empirical relation for power flow through the converter is obtained, and an optimal capacitor link voltage range is derived to achieve power transfer between rated limits. The efficacy of the proposed control algorithm for the EMS is analyzed and proved to be well suited for the self-sustained dc nanogrid. A 5-kVA prototype of the converter is designed and developed in hardware, and the system operation is verified with experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes an improved performance interactive distribution static compensator (DSTATCOM) to address the limitations of conventional current control mode (CCM) and voltage control mode (VCM) operations. The proposed interactive scheme provides smooth transfer of modes of operation while remaining connected in the distribution system. In normal operation, the DSTATCOM operates in CCM to make source currents balanced, sinusoidal, and at a unity power factor. During voltage disturbances, the CCM operation cannot improve load voltage. In that case, DSTATCOM operation is changed to VCM, which maintains a constant voltage across the sensitive loads. Hence, this interactive DSTATCOM ensures continuous, flexible, and robust operation of the load. Moreover, the filter current requirements are reduced in the proposed scheme, which reduces the losses in the filter and feeder, improves inverter efficiency, and requires a reduced-rating inverter for sag mitigation. The principle of operation and control for both operating modes is analyzed. The detailed process of the flexible transfer between the two modes is derived. Deadbeat predictive control algorithms for CCM as well as VCM operation are developed for fast operation during mode transfers. The performance of the proposed scheme is validated by both simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents an effective circuit configuration of a multilevel inverter that can increase the number of output voltage levels with a reduced number of circuit components. The proposed seven-level pulsewidth-modulation inverter consists of a single dc voltage source with a series of capacitors, diodes, active switches for synthesizing output voltage levels, and an H-bridge cell. After theoretical analysis, we carry out computer-aided simulations and experiments to verify the validity of the proposed approach. Here, we also introduce a modified switching strategy to solve the capacitor voltage unbalancing that occurs in series-connected capacitors. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel multiple-input bidirectional dc–dc power converter to interface more than two dc sources of different voltage levels. This finds applications in hybrid electric/fuel cell vehicles (FCVs), where different dc sources of unequal voltage levels need to be connected with bidirectional power flow capability. The converter can be used to operate in both the buck and boost modes with bidirectional power control. It is also possible to independently control power flow between any two sources when more than two sources are actively transferring power in either directions. The operation, analysis, and design of the converter are presented with different modes of power transfer. The proposed converter is demonstrated for FCV application using real-time hardware-in-the-loop system. Experimental results for a 5-kW system are presented, validating the theoretical analysis. [ABSTRACT FROM PUBLISHER]

Grid-connected power converters play a key role in several applications such as the integration of renewable energy sources and motor drives. For this reason, the development of high performance control strategies for this particular class of power converters has increasingly attracted the interest of both academic and industry researchers. This paper presents the predictive optimal switching sequence (OSS) direct power control (DPC) (OSS-DPC) algorithm for grid-connected converters. The OSS-DPC method belongs to the predictive-DPC family and provides the desired power references by calculating globally OSSs. To address computational and implementation issues, an efficient control algorithm, named reduced OSS-DPC, is introduced. The implementation of the proposed control strategy in a standard DSP is evaluated on a two-level power converter prototype working as a STATCOM. Experimental results show the algorithm's potential to provide high performance during both transient and steady states. [ABSTRACT FROM PUBLISHER]

In this paper, a seven-level single-carrier and multi-modulation-wave sinusoidal pulsewidth modulation (SCMM-SPWM) strategy is proposed. In the negative half cycle of the modulation waves (MWs), dc offsets related to the amplitude of the carrier are set on the three MWs, respectively, to apply the same comparison logics of the MWs and carrier during positive and negative half cycles of the MWs. Thus, it is implemented with only one digital signal processor chip without any other attached logical circuit or controller. The reason for generating the zero-crossing voltage pulse disturbance (ZCVPD) in this strategy is analyzed, and the elimination of the ZCVPD is proposed and verified by experimental results. The spectral characters of the conventional multi-MW-based SPWM and the proposed one are originally derived and compared with each other by simulation in detail. The theoretical analysis, simulation, and experimental results indicate that the output characters of the proposed strategy are identical to those of the conventional one; it means that the proposed strategy can replace the conventional one while with the benefit of significantly reducing the cost and bulk of the implemental platform. [ABSTRACT FROM PUBLISHER]

The quasi-Z-source cascaded multilevel inverter (qZS-CMI) presented many advantages over conventional CMI when applied in photovoltaic (PV) power systems. For example, qZS-CMI provides the balanced dc-link voltage and voltage boost ability, saves one-third modules, etc. However, current research studies only disclosed control of single-phase qZS-CMI-based PV power systems, and there was no literature related to control of three-phase qZS-CMI-based PV power systems. In this paper, for the first time, three-phase qZS-CMI's control is proposed and demonstrated for application to PV power systems. The models of PV-panel-fed qZS H-bridge module and qZS-CMI-based PV power system are built to accurately design control algorithms for each module and the whole system. The proposed control method includes the distributed maximum power point tracking for each module, dc-link peak voltage balance control for all modules, and grid-tie control for the whole system; moreover, a new multilevel space vector modulation method is proposed for the three-phase qZS-CMI. Simulation and experimental results on a test bench with a three-phase seven-level qZS-CMI-based PV power system verify the proposed control and modulation methods. [ABSTRACT FROM PUBLISHER]

In this paper, a predictive control scheme is proposed for the low-voltage ride-through (LVRT) enhancement of direct-driven permanent-magnet-synchronous-generator-based megawatt-level wind turbines. The proposed method uses the turbine–generator rotor inertia to store the surplus energy during the grid voltage dips. The power conversion system is realized using a three-phase diode-bridge rectifier, a three-level-boost converter, and a neutral-point-clamped (NPC) inverter. The wind turbine requirements, such as maximum power point tracking, net dc-bus voltage control, balancing of the dc capacitor voltages, and reactive power generation, are modeled as the reference control variables. The generator- and grid-side cost functions are defined to deal with these control objectives. During each sampling interval, the control goals are achieved based on the minimization of cost functions. The coordination of boost and NPC converters and the exchange of reference control variables during normal and LVRT operation are formulated such that the power converters operate in a safe mode while meeting the grid code requirements. Simulation and experimental results are presented to validate the proposed strategy. [ABSTRACT FROM PUBLISHER]

In a six-switch three-phase inverter, the conventional pulsewidth modulation (PWM) has six switching times in every switching period based on the average concept. The used multidimensional feedback quantized modulation (MDFQM) strategy selects one switching state and keeps it in every sampling period based on the minimization of filtered voltage errors between the desired voltage commands and the output voltages. The widths of the output voltage pulse are integer times the fixed sampling time in MDFQM. In this paper, two high-efficiency current control methods based on MDFQM are proposed. They integrate the MDFQM strategy and the current control function to minimize the filtered current errors between the desired current commands and the inverter current. Due to the main advantages of less switching numbers and more closed fundamental current, a high-efficiency performance is achieved. The proposed methods are applied to the current control of a three-phase permanent-magnet synchronous motor. The simulation results and experimental results verify the effectiveness of the proposed methods. [ABSTRACT FROM PUBLISHER]

This paper presents a finite control set model predictive strategy and its application to the load voltage control of two-level four-leg inverters. The proposed approach uses the novel discrete-time model of the inverter and output $LC$ filter in order to predict the variables to be controlled. These predictions are carried out for the 16 switching states of the inverter and are evaluated using a cost function. The switching state that forces the load voltages to be closest to their respective references is chosen and applied to the inverter. The behavior of the predictive controller has been investigated, and the changes to both inductive and capacitive filter parameters have been considered. In order to improve the reliability of the fourth leg as well as the overall inverter efficiency, a solution is proposed, which combines hardware and software reconfigurations. The feasibility of the proposed method is verified through simulation and experimental results considering single-/three-phase, balanced/unbalanced, and linear/nonlinear loads. [ABSTRACT FROM PUBLISHER]

In this paper, two new topologies are proposed for multilevel inverters. The proposed topologies consist of a combination of the conventional series and the switched capacitor inverter units. The proposed topologies reduce the number of switches and isolated dc voltage sources, the variety of the dc voltage source values, and the size and cost of the system in comparison with the conventional topologies. In addition, the proposed topologies can double the input voltage without a transformer. There is no need for complicated methods to balance the capacitor voltage. The simulation and experimental results of single-phase 25- and 17-level inverters are given to prove the correct operation of the proposed topologies. [ABSTRACT FROM PUBLISHER]

This paper presents a multilevel inverter that has been conceptualized to reduce component count, particularly for a large number of output levels. It comprises floating input dc sources alternately connected in opposite polarities with one another through power switches. Each input dc level appears in the stepped load voltage either individually or in additive combinations with other input levels. This approach results in reduced number of power switches as compared to classical topologies. The working principle of the proposed topology is demonstrated with the help of a single-phase five-level inverter. The topology is investigated through simulations and validated experimentally on a laboratory prototype. An exhaustive comparison of the proposed topology is made against the classical cascaded H-bridge topology. [ABSTRACT FROM PUBLISHER]

An architecture of multiple-integrated converter modules sharing an unfolding full-bridge inverter with a pseudo dc link (MIPs) is proposed for grid-connected photovoltaic systems in this paper. The proposed configuration can improve the power conversion, the control circuit complexity, and the cost competitiveness. The proposed MIP is composed of distributed flyback dc–dc converters (DFCs) and an unfolding full-bridge inverter with an ac filter. The DFCs can eliminate the shading effect by using the individual maximum power point tracking. In conventional flyback-type single-phase utility-interactive inverters, discontinuous conduction mode and boundary conduction mode are popular because of the inherent constant current-source characteristics more desirable for grid connection and of the simple procedures for the controller design. However, the operating mode suffers from a large current stress of the circuit components, which leads to the low power efficiency. To avoid this, the DFCs operate under continuous conduction mode that allows reduced current stresses and increased power efficiency, as well as low material cost. The current control loop of the converters employs primary-side regulation contributing to improvement of dynamics as well as the cost reduction significantly due to the elimination of the high-linearity photocoupler device. Development of a new dc-current loop that maintains the level of dc-current injection into the grid within the levels stipulated by IEEE 1547 will be dealt as well. The performance validation of the proposed design is confirmed by experimental results of a 200-W hardware prototype. [ABSTRACT FROM PUBLISHER]

In this paper, a model predictive scheme is proposed to control the grid-connected high-power four-level diode-clamped inverter. To predict the future behavior of active and reactive grid power values and dc link capacitor voltages, a discrete-time model of the inverter is developed in synchronous reference frame. The controller uses all the possible switching states of the inverter for the prediction and evaluates them using a cost function. The switching state, which minimizes the cost function, is then chosen and applied at the next sampling interval. The switching frequency minimization is also achieved by including an extra constraint in the cost function. A simplified extrapolation method with reduced computational burden is proposed to safeguard the semiconductor devices during the dynamic changes in reference power values. The performance of the proposed method is investigated with the perturbations in the grid filter and dc link parameters. The feasibility of the proposed method is verified through simulation and experimental results, showing good dynamic and steady-state performance. [ABSTRACT FROM PUBLISHER]

Loads connected to a stiff source cannot be protected from voltage disturbances using a distribution static compensator (DSTATCOM). In this paper, a new control-algorithm-based multifunctional DSTATCOM is proposed to operate in voltage control mode under stiff source. This scheme provides fast voltage regulation at the load terminal during voltage disturbances and protects critical loads. In addition, during normal operation, the generated reference load voltages allow control of the source currents. Consequently, DSTATCOM injects reactive and harmonic components of load currents to make source power factor unity. Simulation and experimental results are presented to verify the efficacy of the proposed control algorithm and multifunctional DSTATCOM. [ABSTRACT FROM PUBLISHER]

This paper proposes the pulsewidth modulation (PWM) strategy of Z-source inverters (ZSIs) with minimum inductor current ripple. In existing PWM strategy with single-phase shoot-through, the shoot-through time interval is divided into six equal parts, therefore the three phase legs bear the equal shoot-through time interval. In this manner, the allotment and arrangement of the shoot-through state is easy to realize, but the inductor current ripple is not optimized. This causes to use relatively large inductors. In the proposed PWM strategy, the shoot-through time intervals of three phase legs are calculated and rearranged according to the active state and zero state time intervals to achieve the minimum current ripple across the Z-source inductor, while maintaining the same total shoot-through time interval. The principle of the proposed PWM strategy is analyzed in detail, and the comparison of current ripple under the traditional and proposed PWM strategy is given. Simulation and experimental results on the series ZSI are shown to verify the analysis. [ABSTRACT FROM PUBLISHER]

A new scheme for nine-level voltage space-vector generation for medium-voltage induction motor (IM) drives with open-end stator winding is presented in this paper. The proposed nine-level power converter topology consists of two conventional three-phase two-level voltage source inverters powered by isolated dc sources and six floating-capacitor-connected H-bridges. The H-bridge capacitor voltages are effectively maintained at the required asymmetrical levels by employing a space vector modulation (SVPWM) based control strategy. An interesting feature of this topology is its ability to function in five- or three-level mode, in the entire modulation range, at full-power rating, in the event of any failure in the H -bridges. This feature significantly improves the reliability of the proposed drive system. Each leg of the three-phase two-level inverters used in this topology switches only for a half cycle of the reference voltage waveform. Hence, the effective switching frequency is reduced by half, resulting in switching loss reduction in high-voltage devices. The transient as well as the steady-state performance of the proposed nine-level inverter-fed IM drive system is experimentally verified in the entire modulation range including the overmodulation region. [ABSTRACT FROM PUBLISHER]

Cascaded H-bridge multilevel power electronic converters generally require several dc sources. An alternative option is to replace all the separate dc sources feeding the H-bridge cells with capacitors, leaving only one H-bridge cell with a real dc voltage source. This will yield a cost-effective converter. However, the required capacitor voltage balancing is challenging. In this paper, using the phase-shift modulation approach, a new control method for cascaded H-bridge multilevel converters fed with only one independent dc source is presented. The proposed method has a wide voltage regulation range for the replacement capacitors in the H-bridge cells. Experimental and simulation results support the proposed control method. [ABSTRACT FROM PUBLISHER]

The five-level active neutral-point (NP)-clamped (ANPC) converter is a newly emerging topology which can overcome the drawbacks of traditional NP-clamped and flying-capacitor multilevel converters. This paper presents a comprehensive theoretical analysis of the NP potential balancing issue and demonstrates that the NP potential can be naturally balanced under ideal and steady conditions. An NP potential balancing method based on zero-sequence voltage injection is presented. By calculating the average NP currents of all key zero-sequence voltages, the most appropriate zero-sequence voltage is selected to generate the demanded NP current, which can also limit the switching frequency of the series-connected insulated-gate bipolar transistors to the fundamental frequency. A three-phase five-level ANPC inverter prototype is built up, and both steady and dynamic experimental results are presented to verify the validity of this method. [ABSTRACT FROM PUBLISHER]

In this paper, a single-phase multilevel inverter with battery balancing is proposed. The input of each individual inverter is directly connected to a battery. The combination of batteries can be controlled according to the batteries' voltages to implement the battery-balancing function. The operational principle of the proposed system is first described, and then, the design equation is derived. Experiments show that the battery-balancing discharge function is achieved. Finally, a prototype is designed and implemented to verify the feasibility and excellent performance. [ABSTRACT FROM PUBLISHER]

A neutral-point-clamped three-level inverter with small dc-link capacitors is presented in this paper. The inverter requires zero average neutral-point current for stable neutral-point voltage. The small dc-link capacitors may not maintain capacitor voltage balance, even with zero neutral-point current. This may happen due to nonlinearities present in the circuit. This requires a fast control of the neutral-point voltage. A simple carrier-based modulation strategy which allows modeling of the neutral-point voltage dynamics as a continuous function of power drawn from the inverter is proposed. This continuous model shows that the neutral-point current is proportional to the power drawn from the inverter, and it enables the use of a well-established classical control theory for the neutral-point voltage controller design. A simple proportional integral controller is designed for the neutral-point voltage control on the basis of the continuous model. The design method for optimum performance is discussed. The implementation of the proposed modulation strategy and the controller is very simple. The controller is implemented in a 7.5-kW induction machine-based drive with only 14 \mu \F dc-link capacitors. Also, the experimental results show that fast and stable performance of the neutral-point voltage controller are achieved and thus verify the validity of the proposed control approach. [ABSTRACT FROM PUBLISHER]

Reforms in the electricity sector along with various renewable-energy-promotion policies have increased the importance of small grid-connected photovoltaic (PV) systems utilizing single-stage single-phase inverters. Ruggedness, reliability, and cost effectiveness are the desirable characteristics of such inverters used in distributed low-power applications. Schemes based on one-cycle control (OCC) which do not require the service of a phase-locked loop for interfacing the inverter to the grid are increasingly being employed for such applications. However, the OCC-based schemes reported earlier require sensing of the grid voltage which somewhat offsets one of the inherent strengths of OCC-based systems. In an effort to overcome the aforementioned limitation, an OCC-based grid-connected single-stage PV system is proposed in this paper which does not require to sense the grid voltage. Further, it requires less number of sensors (two) as compared to that required (four) in the earlier reported scheme for the implementation of the core controller comprising of OCC and maximum-power-point-tracking blocks. The viability of the proposed scheme is confirmed by performing simulation and experimental validation. [ABSTRACT FROM PUBLISHER]

This paper proposed a novel predictive variable-structure-switching-based current controller for a three-phase load driven by a power inverter. The design specifications are robustness to load electrical parameters, fast dynamic response, reduced switching frequency, and simple hardware implementation. In order to meet previous specifications, a sliding mode controller has been developed, which is designed as finite-state automata, and implemented with a field-programmable gate array (FPGA) device. The switching strategy implemented within the state transition diagram provides for a minimum number of switches by the three-phase inverter that is confirmed through simulation and experimental results. Its regulation using the proposed control law provides good transient response by the brushless ac motor control. However, this does not limit the wider applicability of the proposed controller that is suitable for different types of ac loads (rectifier and inverter) and ac motors (induction, synchronous, and reluctance). A new logical FPGA torque and speed controller is developed, analyzed, and experimentally verified. [ABSTRACT FROM PUBLISHER]

The increasing number of distributed generation units has led to the development of microgrids, to which the distributed generators are commonly interfaced by means of a voltage-source inverter (VSI). When the microgrid is operating independently of the power system, i.e., in islanded mode, two levels of control can be distinguished for these VSIs: power control and voltage control (frequency and amplitude). The set-point values for the voltage controller are obtained from the power controller. This paper investigates theoretically and experimentally the benefits of using several PID control structures for the voltage control. Theoretical insights into the dynamics of such a system emphasize the benefits of measuring current signals for control purposes and adding voltage measurements to the output of the controllers. Direct voltage control and cascade voltage control are compared both with and without forward compensation of the grid voltage. Simulation and experimental results are given showing that such PID-type controllers on a digital signal processor are simple yet effective strategies for an accurate voltage control in islanded microgrids. [ABSTRACT FROM PUBLISHER]

This paper extends the Z-source concept to matrix converters and explores a family of Z-source matrix converters. Their principles and characteristics are analyzed, and a simplified voltage-fed Z-source matrix converter is used as an example to demonstrate its operation, voltage gain versus modulation index, PWM method, boost control, and implementation of the control. Both simulation and experimental results verify operation of the proposed Z-source matrix converter, analytical results, and control method. The Z-source converters can achieve buck and boost operation with reduced number of switches needed, therefore achieving low cost, high efficiency, and reliability, compared to the traditional matrix converters. [ABSTRACT FROM AUTHOR]

Power converters consisting of naturally commutated thyristors such as cycloconverters and current source inverters were the first to be used in driving electrical motors with variable speed, but now, due to their inferior performance compared to forced commutated converters, their use is restricted in the high voltage/high power range where the performance and cost of forced commutated switching devices are not yet competitive. Hybrid cycloconverters proposed recently are capable of improving the performance of cycloconverters by adding an auxiliary forced commutated inverter with reduced installed power. It will be shown that the new topology is not only able to improve the quality of the output voltage but is also able to enhance the control over the circulating current and, therefore, for some of the cycloconverter arrangements, to improve the input power quality. This paper evaluates the performance of a few standard and hybrid cycloconverter arrangements using both simulation and experimental results. [ABSTRACT FROM AUTHOR]

Common-mode voltage (CMV) is responsible for overvoltage stress to the winding insulation and bearing damage of an ac motor. High dv/dt of CMV raises leakage currents, which can cause serious problems such as motor damage and electromagnetic noise to the equipment installed near the converter. This paper proposes two modulation strategies for indirect matrix converters that substantially eliminate CMV. The first method is developed by using the suitable couple of nonzero space vectors instead of zero space vectors in the inverter stage. The maximum voltage transfer ratio of this method is unaffected and remains 0.866. The second one, which is useful for low-voltage operation, is approached by choosing the medium and the lowest positive line-to-line input voltages in the rectifier stage to generate the dc-link voltage and by placing suitable zero space vectors in the inverter stage. In the second method, the maximum voltage transfer ratio is 0.5. Both methods can mitigate the peak value to 42%. In addition, while the first method provides the same performance to the conventional method, the second method can reduce significantly the harmonic components of line-to-line output voltage. Simulation and experimental results are shown to verify the effectiveness of the proposed methods. [ABSTRACT FROM AUTHOR]

In this paper, a real-time circulating current reduction method for parallel harmonic-elimination pulsewidth modulation (HEPWM) inverters is proposed. HEPWM techniques are often used in high-capacity inverters. For instance, in a hybrid microgrid, the inverters are employed to transfer power between the dc and ac buses. If the inverters are in parallel operation, the zero-sequence path can be established, and the zero-sequence circulating current will circulate among the inverters. The proposed method installs a cascade null-vector control system behind the conventional three-phase HEPWM modulator. The proposed null-vector control system can be disabled to save switching losses when the zero-sequence circulating current is small, whereas it can be enabled when the zero-sequence circulating current becomes large. The proposed method does not affect the line-to-line voltage waveforms of HEPWM inverters, and it can easily enable/disable the null-vector control system to provide bumpless transfer. Compared with the conventional HEPWM with zero-sequence harmonics elimination, the proposed method can provide an extra 15% modulation index range. Results that were obtained from both simulation and experiments confirmed the performance and effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

With regard to a five-level inverter comprising flying-capacitor asymmetric H-bridge, the impact on the capacitor voltage under conventional modulation approach is analyzed. Since it is sensitive to the fundamental period and the load current, it may introduce undesired low-order harmonics into the output voltage and may even break down the power switches due to the considerable fluctuation of the flying-capacitor voltage. Thus, this paper proposes a novel pulsewidth-modulation scheme with the positive and negative cross carriers, which controls the flying-capacitor voltage by utilizing the redundant switching states of the output voltages. Three modes of precharging the flying capacitor without extra equipments are presented. Moreover, the capacitance of the flying capacitor and the switching frequency of the power switches can be chosen according to the allowable fluctuation of the flying-capacitor voltage and the load current. In order to remove the overlapping of the level layers, the optimization of the line-to-line voltage waveform is proposed to synthesize the reference vector with the “nearest three-vector” approach. The theory is supported by the experimental results from the prototype. [ABSTRACT FROM AUTHOR]

This paper describes a novel switching signal generator for three-phase voltage source inverters. Unlike conventional space-vector pulsewidth modulation (SVPWM) which achieves three-phase input voltage by a combination of the basic space vectors, the proposed scheme produces optimal switching commands to minimize the filtered measure of quantization error. Under specific selections of the filter matrix and the quantization scheme, it is shown that the proposed modulator is equivalent to SVPWM. An experimental platform is built to verify the effectiveness of the proposed scheme. It is shown that the switching number of the proposed method is reduced without sacrificing the harmonic distortion within the input frequency band under various reference signals. [ABSTRACT FROM AUTHOR]

This paper proposes a single-phase seven-level inverter for grid-connected photovoltaic systems, with a novel pulsewidth-modulated (PWM) control scheme. Three reference signals that are identical to each other with an offset that is equivalent to the amplitude of the triangular carrier signal were used to generate the PWM signals. The inverter is capable of producing seven levels of output-voltage levels (Vdc, 2Vdc/3, Vdc/3, 0, -Vdc, -2Vdc/3, -Vdc/3) from the dc supply voltage. A digital proportional–integral current-control algorithm was implemented in a TMS320F2812 DSP to keep the current injected into the grid sinusoidal. The proposed system was verified through simulation and implemented in a prototype. [ABSTRACT FROM AUTHOR]