Search

Local dc distribution systems or dc nanogrids for residential and commercial buildings are growing popular due to the increased focus on energy savings. Using low-voltage dc for the nanogrid provides various advantages such as easier integration with renewable sources and battery banks, increased savings, etc. Future systems would use renewable sources and storage devices to become self-sufficient in generation with bare minimum consumption from the grid. The objective of this paper is to develop an energy management system (EMS) to provide uninterrupted power supply to the dc loads and achieve self-sufficiency by minimizing grid power consumption. This is achieved by developing a control scheme for a cascaded two-stage bidirectional converter interface between the nanogrid and the ac distribution network. In addition, an empirical relation for power flow through the converter is obtained, and an optimal capacitor link voltage range is derived to achieve power transfer between rated limits. The efficacy of the proposed control algorithm for the EMS is analyzed and proved to be well suited for the self-sustained dc nanogrid. A 5-kVA prototype of the converter is designed and developed in hardware, and the system operation is verified with experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes an improved performance interactive distribution static compensator (DSTATCOM) to address the limitations of conventional current control mode (CCM) and voltage control mode (VCM) operations. The proposed interactive scheme provides smooth transfer of modes of operation while remaining connected in the distribution system. In normal operation, the DSTATCOM operates in CCM to make source currents balanced, sinusoidal, and at a unity power factor. During voltage disturbances, the CCM operation cannot improve load voltage. In that case, DSTATCOM operation is changed to VCM, which maintains a constant voltage across the sensitive loads. Hence, this interactive DSTATCOM ensures continuous, flexible, and robust operation of the load. Moreover, the filter current requirements are reduced in the proposed scheme, which reduces the losses in the filter and feeder, improves inverter efficiency, and requires a reduced-rating inverter for sag mitigation. The principle of operation and control for both operating modes is analyzed. The detailed process of the flexible transfer between the two modes is derived. Deadbeat predictive control algorithms for CCM as well as VCM operation are developed for fast operation during mode transfers. The performance of the proposed scheme is validated by both simulation and experimental results. [ABSTRACT FROM PUBLISHER]

Multiple-output Switched Mode Power Supplies (SMPSs) for personal computers (PCs) normally depict extremely bad power quality indices at the utility interface such as total harmonic distortion of the input current being more than 80%, power factor being lower than 0.5 and output voltage regulation being very poor. They violate the limits of harmonic emissions set by international power quality standards. In this paper, a nonisolated power factor corrected (PFC) converter is being proposed to be used at the front end to improve the power quality of an SMPS for a PC. The front-end converter is able to reduce the 100-Hz ripple in its output that is being fed to the second stage isolated converter. The performance of the front-end Zeta converter is evaluated in three different operating conditions to select the best operating condition for the proposed SMPS system. The performance of the proposed SMPS is simulated and a laboratory prototype is developed to validate its performance. Test results are found to be in line with the simulated performance under varying input voltages and loading conditions and all the results demonstrate its enhanced performance. [ABSTRACT FROM PUBLISHER]

A single-objective predictive control method that deals with four main control objectives applied to a multivariable single-phase three-level neutral-point-clamped converter operating as an active power filter is proposed in this paper. The four control objectives are to self-support the dc-bus voltage under load variations, to compensate the reactive power and the current harmonics, and to balance the dc capacitor voltages by using a predefined combination of the redundant switching states of the converter. The main contribution of the proposed method is that these objectives are accomplished without using weighting factors in the cost function, which eliminates problems such as multiobjective optimization or additional empirical procedures for determination of these factors. As a result, the method is easy to implement and rapidly selects the optimal voltage to improve the dynamic-state performance. Experimental results from a 2-kVA prototype are presented to prove that the method is valid for single-phase compensation. The well-known effect of model parameter errors' issue, which is inherent in predictive control methods, is also tested to confirm that the harmonic distortion in the grid current is below 5% even when the predictive model has a 25% error between actual and theoretically estimated grid impedance values. [ABSTRACT FROM PUBLISHER]

The modular multilevel converter (MMC) becomes attractive for medium- or high-power applications because of the advantages of high modularity, availability, and power quality. One of the technical challenges associated with an MMC is the balancing of the capacitors' voltages. In this paper, a voltage-balancing control method is proposed for the MMC under phase-shifted carrier-based pulsewidth modulation. The proposed voltage-balancing method uses the linearization method for pulse sorting without arm current measurement, which can control the capacitor charge transfer to balance the capacitor voltage in the MMC. In the proposed method, the voltagebalancing algorithm is implemented in each carrier wave period, which reduces the computational intensity and burden. In addition, the arm current can also be improved with the proposed method. The simulation studies with the professional tool PSCAD/EMTDC are conducted, and a downscale MMC prototype is also tested with the proposed method. The study results show the effectiveness of the proposed voltage-balancing method. [ABSTRACT FROM PUBLISHER]

This paper presents a power factor correction (PFC)-based bridgeless isolated Cuk converter-fed brushless dc (BLDC) motor drive. A variable dc link voltage of the voltage source inverter (VSI) feeding the BLDC motor is used for its speed control. This allows the operation of VSI in fundamental frequency switching to achieve an electronic commutation of the BLDC motor for reduced switching losses. A bridgeless configuration of an isolated Cuk converter is derived for the elimination of the front-end diode bridge rectifier to reduce conduction losses in it. The proposed PFC-based bridgeless isolated Cuk converter is designed to operate in discontinuous inductor current mode to achieve an inherent PFC at the ac mains. The proposed drive is controlled using a single voltage sensor to develop a cost-effective solution. The proposed drive is implemented to achieve a unity power factor at the ac mains for a wide range of speed control and supply voltages. An improved power quality is achieved at ac mains with power quality indices within the limits of the IEC 61000-3-2 standard. [ABSTRACT FROM PUBLISHER]

This paper analyzes the interleaved boost with coupled inductors (IBCI) converter, which is an isolated topology that is suitable for high step-up applications. Two main contributions are given: an exhaustive steady-state analysis and an accurate small-signal model. The former allows for deriving a closed-form noniterative design procedure for the power-stage active and passive components. In addition, it reveals an interesting equivalence with an apparently different converter, i.e., the single active bridge. Subsequently, the IBCI converter dynamic behavior is investigated, deriving a nonlinear average model that, under small-signal approximation, can be linearized around a given operating point and used for feedback controller design. A single photovoltaic module interface converter, rated for 300-W output power, is considered as a case study to validate the analysis outcome and the design procedure. Both are fully validated by measurements taken on the laboratory prototype. [ABSTRACT FROM PUBLISHER]

This paper presents an effective circuit configuration of a multilevel inverter that can increase the number of output voltage levels with a reduced number of circuit components. The proposed seven-level pulsewidth-modulation inverter consists of a single dc voltage source with a series of capacitors, diodes, active switches for synthesizing output voltage levels, and an H-bridge cell. After theoretical analysis, we carry out computer-aided simulations and experiments to verify the validity of the proposed approach. Here, we also introduce a modified switching strategy to solve the capacitor voltage unbalancing that occurs in series-connected capacitors. [ABSTRACT FROM PUBLISHER]

This paper presents a capacitor voltage balancing control applicable to any multilevel dc–ac converter formed by a single set of series-connected capacitors implementing the dc link and semiconductor devices, such as the diode-clamped topology. The control is defined for any number of dc-link voltage levels and converter legs (for single-phase and multiphase systems), guaranteeing the capacitor voltage control for any modulation index value and load (from idle mode to full power). The associated control loop small-signal transfer function is presented, from which optimum compensator design guidelines are derived. The improvement in control performance is verified through simulation and experiments comparing with a previous balancing control strategy in a four-level three-phase dc–ac conversion system. The satisfactory control performance is also verified through simulation in a four-level five-phase dc–ac conversion system. [ABSTRACT FROM PUBLISHER]

The modular multilevel converter (MMC) becomes attractive for high-voltage and high-power applications due to its high modularity, availability, and power quality. The voltage balance issue of capacitors is very important in the MMC, and balancing of the capacitor voltage is increasingly difficult as the switching frequency is reduced. In this paper, a voltage-balancing method is proposed for the MMC switched at grid frequency with reduced losses and does not rely on the arm current. By assigning the low-frequency pulses with different pulsewidths, the capacitor charge transfer in the MMC can be controlled for keeping the capacitor voltage balancing in the MMC. Simulations and experimental studies of the MMC are conducted, and the results confirm the effectiveness of the proposed capacitor voltage-balancing method. [ABSTRACT FROM PUBLISHER]

A single-switch nonisolated dc/dc converter for a stand-alone photovoltaic (PV)-battery-powered pump system is proposed in this paper. The converter is formed by combining a buck converter with a buck-boost converter. This integration also resulted in reduced repeated power processing, hence improving the conversion efficiency. With only a single transistor, the converter is able to perform three tasks simultaneously, namely, maximum-power-point tracking (MPPT), battery charging, and driving the pump at constant flow rate. To achieve these control objectives, the two inductors operate in different modes such that variable switching frequency control and duty cycle control can be used to manage MPPT and output voltage regulation, respectively. The battery in the converter provides a more steady dc-link voltage as compared to that of a conventional single-stage converter and hence mitigates the high voltage stress problem. Experimental results of a 14-W laboratory prototype converter with a maximum efficiency of 92% confirmed the performance of the proposed converter when used in a PV-battery pump system. [ABSTRACT FROM PUBLISHER]

Conventional matrix converters (MCs) have limited voltage gain that is less than 0.866, whether for direct MC (DMC) or indirect MC (IMC). Existing Z-source (ZS)/discontinuous quasi-Z-source (qZS) DMCs and ZS IMCs achieved larger than 0.866 voltage gain; however, the former inherited the complex commutation from DMC, and the latter involved a ZS network in dc link and led to non-all-silicon solution. In this paper, ZS and discontinuous qZS networks of existing ZS/qZS DMCs are used for an IMC topology for simplifying commutation and having high voltage gain, but they require extra input filter to reduce current harmonics. A new continuous qZS IMC is proposed, where a qZS network integrates the filtering function of the grid side; hence, additional input filter is avoided in the proposed continuous qZS IMC. Three new IMCs are compared in detail, in terms of voltage gain, current ripple, voltage ripple, inductor current and capacitor voltage stresses, ZS/qZS switch current and voltage stresses, filtering function, input current total harmonic distortion (THD), output voltage THD, and efficiency. Their control and modulation methods are presented to achieve the desired performances. Experimental comparisons verify the theoretical analysis and that the proposed continuous qZS IMC is a promising topology. [ABSTRACT FROM PUBLISHER]

This paper presents input-series–output-parallel (ISOP) configuration for single-phase front-end buck rectifiers (BRs). The configuration is especially suitable for traction applications, where the complete rectification system needs to withstand high ac voltages and supply medium-power loads. The primary rectification module of the proposed configuration is based on pulsewidth-modulated BR (current source inverter topology). The desired isolation, mandatory for ISOP connection, is provided at the dc stage through a medium-frequency/high-frequency transformer. Equal power sharing by modules is achieved from the ac side through input voltage and current sharing. The proposed control scheme is configured using two loops. While the outer loop regulates the output dc voltage and active wave shaping of the source current, the inner loop ensures stable voltage sharing. The performance of the proposed ISOP configuration is verified using numerical simulation. Experimental verification is achieved through a 2-kW grid-connected laboratory prototype. [ABSTRACT FROM PUBLISHER]

This paper presents a power factor correction (PFC)-based bridgeless canonical switching cell (BL-CSC) converter-fed brushless dc (BLDC) motor drive. The proposed BL-CSC converter operating in a discontinuous inductor current mode is used to achieve a unity power factor at the ac mains using a single voltage sensor. The speed of the BLDC motor is controlled by varying the dc bus voltage of the voltage source inverter (VSI) feeding the BLDC motor via a PFC converter. Therefore, the BLDC motor is electronically commutated such that the VSI operates in fundamental frequency switching for reduced switching losses. Moreover, the bridgeless configuration of the CSC converter offers low conduction losses due to partial elimination of diode bridge rectifier at the front end. The proposed configuration shows a considerable increase in efficiency as compared with the conventional scheme. The performance of the proposed drive is validated through experimental results obtained on a developed prototype. Improved power quality is achieved at the ac mains for a wide range of control speeds and supply voltages. The obtained power quality indices are within the acceptable limits of IEC 61000-3-2. [ABSTRACT FROM PUBLISHER]

In a photovoltaic (PV)- or fuel-cell-based grid-connected power system, a high step-up dc–dc converter is required to boost the low voltage of a PV or fuel cell to a relatively high bus voltage for the downstream dc–ac grid-connected inverter. To integrate the advantages of the high voltage gain of a switched-capacitor (SC) converter and excellent output regulation of a switching-mode dc–dc converter, a method of combining the two types of converters is proposed in this paper. The basic idea is that when the switch is turned on, the inductor is charged, and the capacitors are connected in series to supply the load, and when the switch is turned off, the inductor releases energy to charge multiple capacitors in parallel, whose voltages are controlled by a pulsewidth modulation technique. Thus, a high voltage gain of the dc–dc converter can be obtained with good regulation. Based on this principle, a series of new topologies are derived, and the operating principles and voltage gains of the proposed converters are analyzed. Finally, the design of the proposed converter is given, and the experiment results are provided to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

This paper proposes a voltage balancing method for a flying capacitor multilevel converter based on the phase-disposition sinusoidal pulsewidth modulation (PD-SPWM). This voltage balancing method uses redundant switching states, which are determined by the minimization of a cost function. The implementation of the PD-SPWM using standard triangular carriers leads to additional switching events that are due to the transitions within the same voltage level, thus increasing the switching frequency of the power devices. Such drawback can be avoided by using sawtooth carrier waveforms. Another characteristic of the proposed voltage balancing method is that it does not require the tuning of parameters to achieve optimal performance. Simulation and experimental results confirm the robustness of the proposed method operating with different loads and transient conditions. [ABSTRACT FROM PUBLISHER]

In this paper, a predictive control scheme is proposed for the low-voltage ride-through (LVRT) enhancement of direct-driven permanent-magnet-synchronous-generator-based megawatt-level wind turbines. The proposed method uses the turbine–generator rotor inertia to store the surplus energy during the grid voltage dips. The power conversion system is realized using a three-phase diode-bridge rectifier, a three-level-boost converter, and a neutral-point-clamped (NPC) inverter. The wind turbine requirements, such as maximum power point tracking, net dc-bus voltage control, balancing of the dc capacitor voltages, and reactive power generation, are modeled as the reference control variables. The generator- and grid-side cost functions are defined to deal with these control objectives. During each sampling interval, the control goals are achieved based on the minimization of cost functions. The coordination of boost and NPC converters and the exchange of reference control variables during normal and LVRT operation are formulated such that the power converters operate in a safe mode while meeting the grid code requirements. Simulation and experimental results are presented to validate the proposed strategy. [ABSTRACT FROM PUBLISHER]

This paper presents a modulation strategy for symmetrical cascaded multilevel converters that simultaneously balances the individual DC voltages and reduces switching losses by eliminating redundant or unnecessary commutations. The voltage regulation is based on a 1-bit digital signal indicating whether the DC link voltage of each H-bridge is above or below the set point. The system command identifies commutations that can be suppressed without causing output voltage distortion, thus reducing converter losses. The voltage balancing is reached by postponing each switching commutation for a short lapse of time. Simulation and experimental results for an active filter application validate the proposed methods. [ABSTRACT FROM PUBLISHER]

In this paper, two new topologies are proposed for multilevel inverters. The proposed topologies consist of a combination of the conventional series and the switched capacitor inverter units. The proposed topologies reduce the number of switches and isolated dc voltage sources, the variety of the dc voltage source values, and the size and cost of the system in comparison with the conventional topologies. In addition, the proposed topologies can double the input voltage without a transformer. There is no need for complicated methods to balance the capacitor voltage. The simulation and experimental results of single-phase 25- and 17-level inverters are given to prove the correct operation of the proposed topologies. [ABSTRACT FROM PUBLISHER]

This paper presents a single-phase transformerless grid-connected photovoltaic converter based on two cascaded full bridges with different dc-link voltages. The converter can synthesize up to nine voltage levels with a single dc bus, since one of the full bridges is supplied by a flying capacitor. The multilevel output reduces harmonic distortion and electromagnetic interference. A suitable switching strategy is employed to regulate the flying-capacitor voltage, improve the efficiency (most devices switch at the grid frequency), and minimize the common-mode leakage current with the help of a novel dedicated circuit (transient circuit). Simulations and experiments confirm the feasibility and good performance of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, a model predictive scheme is proposed to control the grid-connected high-power four-level diode-clamped inverter. To predict the future behavior of active and reactive grid power values and dc link capacitor voltages, a discrete-time model of the inverter is developed in synchronous reference frame. The controller uses all the possible switching states of the inverter for the prediction and evaluates them using a cost function. The switching state, which minimizes the cost function, is then chosen and applied at the next sampling interval. The switching frequency minimization is also achieved by including an extra constraint in the cost function. A simplified extrapolation method with reduced computational burden is proposed to safeguard the semiconductor devices during the dynamic changes in reference power values. The performance of the proposed method is investigated with the perturbations in the grid filter and dc link parameters. The feasibility of the proposed method is verified through simulation and experimental results, showing good dynamic and steady-state performance. [ABSTRACT FROM PUBLISHER]

In this paper, multiloop interleaved control (MIC) is proposed, and it is combined with conventional multiloop control and the interleaved pulsewidth modulation scheme. The average behavior of the interleaved three-level switch-mode rectifier (SMR) behaves similar to the conventional boost-type SMR even though two capacitor voltages are imbalanced. It implies that conventional multiloop control can be applied to the interleaved three-level SMRs to achieve the desired power factor correction function. The proposed MIC is digitally implemented and verified in a field-programmable-gate-array-based system. The provided results show that MIC stably works and the capacitor voltages are eventually balanced during the system operations. [ABSTRACT FROM PUBLISHER]

Loads connected to a stiff source cannot be protected from voltage disturbances using a distribution static compensator (DSTATCOM). In this paper, a new control-algorithm-based multifunctional DSTATCOM is proposed to operate in voltage control mode under stiff source. This scheme provides fast voltage regulation at the load terminal during voltage disturbances and protects critical loads. In addition, during normal operation, the generated reference load voltages allow control of the source currents. Consequently, DSTATCOM injects reactive and harmonic components of load currents to make source power factor unity. Simulation and experimental results are presented to verify the efficacy of the proposed control algorithm and multifunctional DSTATCOM. [ABSTRACT FROM PUBLISHER]