Search

This paper presents an optimization method for selective harmonic elimination in a cascaded multilevel inverter using teaching–learning-based optimization (TLBO). The main objective in selective harmonic elimination (SHE) strategy is to eliminate low-order harmonics by solving nonlinear equations and reaching optimal solution, while the fundamental component is satisfied. In this paper, in one side, the influence of optimal dc sources is investigated to reach the SHE goal, and in another side, comparing optimization methods is considered. In this paper, the TLBO as a recently emerged nature-inspired algorithm is presented to provide better results for the SHE in comparison with genetic algorithm, artificial bee colony, imperialistic competitive algorithm, harmony search, ant colony optimization, particle swarm optimization, and differential evolution. For better comparison of those methods and influence of optimal dc sources, 5-, 9-, and 15-level inverters are chosen and MATLAB software is used for optimization. Simulation results show the superiority of TLBO, higher precision and probability of convergence than other mentioned algorithms. Finally, to validate the influence of optimal dc sources and the accuracy of TLBO results, the experimental setup is conducted for a 5-level cascaded H-bridge inverter with optimal dc sources. [ABSTRACT FROM AUTHOR]

A multilevel dodecagonal voltage space vector generation scheme for variable-speed drive applications with single-dc-link operation requires a large value of capacitance for cascaded H-bridge (CHB) filters, when operated at lower speeds. In existing schemes, the multilevel dodecagonal structure is obtained by cascading a flying capacitor inverter with a CHB. In this paper, a new scheme has been proposed to minimize the capacitance requirement for full speed operation by creating vector redundancies using modular and equal voltage CHBs. Also, an algorithm has been developed to optimize the selection of vector redundancies among the CHBs in order to minimize the voltage ripple of the floating capacitors. The proposed algorithm considers instantaneous capacitor voltages and phase currents for optimal selection of vector redundancies. A mathematical model for capacitor voltage deviation is presented, and the effectiveness of the proposed algorithm is verified in both the simulation and the experiment. [ABSTRACT FROM AUTHOR]

Due to the pulsating power at the inverter output terminals, the passive storage elements of the boost stage of the current-fed switched inverter (CFSI) contain a power frequency harmonic component (100 Hz), apart from dc and switching frequency components. In prior designs, the second harmonic component is suppressed by increasing the size of the input filter inductor and capacitor or by using additional circuits. This paper presents a complete characterization of a control-based approach to suppress the power frequency harmonic component in the input inductor current of a CFSI. It also presents a comprehensive characterization of the harmonic power redistribution. Using the proposed approach, it is demonstrated that the inductor value of a CFSI is reduced by 61% for the same peak-to-peak ripple. This leads to an improvement in the conversion ratio, efficiency, and power density of the overall converter. A SiC MOSFET-based CFSI with 75-kHz switching frequency is used to verify the proposed design philosophy. [ABSTRACT FROM AUTHOR]

Conventional two-level as well as multilevel voltage-source-inverter topologies with a hexagonal voltage-space vector structure generate low-order harmonics in the machine terminal voltages when operated beyond the linear modulation range in variable speed drive application. Progressing from hexagonal to a higher sided polygonal voltage-space-vector structure (VSVS) suppresses significant low-order harmonics throughout the modulation range. In addition, the linear modulation range will also be enhanced very near to the base speed. In this paper, for the first time, the generation of a multilevel 24-sided VSVS using a single dc source for induction-motor drives is proposed. A cascaded topology with a dc-source-fed flying-capacitor inverter and two low-voltage capacitor-fed H-bridge cells forms the power circuit. The features and advantages of the proposed scheme are validated through experimental results and discussions. [ABSTRACT FROM AUTHOR]

In this paper, performances on two kinds of aggregated flyback microinverters are compared in aspect of harmonic resonances, which are controlled by current feedback control and peak current control. Based on the Norton models of flyback microinverters obtained by a small-signal modeling approach, potential harmonic resonances with the grid are analyzed. Following that, an impedance-based stability criterion is proposed, where the resonance frequency can be calculated and predicted based on the derived Norton models and the system admittance matrix of aggregated microinverters. After comprehensive analysis and comparisons, it is found that the peak-current-control-based flyback microinverters has better performance on damping the harmonic resonances than the current feedback controlled one. Simulations and experiments are carried out for verifying the effectiveness of the presented models and the correctness of the analysis results. [ABSTRACT FROM AUTHOR]

Microinverters operating into the single-phase grid from new energy source with low-voltage output face the challenges of efficiency bottleneck and twice-line-frequency variation. This paper proposed a multilevel inverter based on bridge modular switched-capacitor (BMSC) circuits with its superiority in conversion efficiency and power density. The topology is composed of dc–dc and dc–ac stages with independent control for each stage, aiming to improve system stability and simplify the control method. The BMSC dc–dc stage, which can be expanded to synthesize more levels, not only features multilevel voltage gain but also partially replaces the original bulk input capacitor and functions as an active energy buffer to enhance power-decoupling ability between dc and ac sides. In dc–ac stage, the control strategy of optimized unipolar frequency doubling sine-wave pulse width modulation is proposed to improve the quality of output waveform. Meanwhile, the multilevel voltage phase has been optimized to further reduce the power loss. Finally, a prototype has been built and tested. Associated with the simulation, the experimental results validate the practicability of these analyses. [ABSTRACT FROM PUBLISHER]

A merit of the interleaving reducing the switching harmonics allows for the reduction of the filter inductance. However, in the case of direct parallel voltage source inverters (VSIs), a severe circulating current occurs. To suppress the high frequency circulating current, coupled inductors (CIs) for the high impedance is inserted. However, the employed CIs induce a positive- or negative-sequence circulating current (i.e., a cross current) besides the zero-sequence circulating current already mentioned in the other papers. Due to different impedances developed by the current characteristics and the cross current in the CIs, VSIs becomes unstable when the resonant controllers are applied for the harmonic compensation such as 5, and 7th harmonics. In this paper, the cross currents and the impedances of CIs varying with the current characteristics are mathematically analyzed, and a novel current controller is proposed to solve this stability problem. The experimental results validate the proposed control scheme. [ABSTRACT FROM PUBLISHER]

This paper proposes an analytical procedure for computation of all pairs of valid switching angles used in pattern generation in five-level H-bridge cascaded inverters. The proposed procedure eliminates harmonic components from inverter output voltage and, for each harmonic, returns the exact boundaries of all valid modulation index intervals. Due to its simple mathematical formulation, it can be easily implemented in real time using a digital signal processor or a field-programmable gate array. In this paper, after a detailed description of the method, simulation and experimental results demonstrate the high quality of achievable results. [ABSTRACT FROM PUBLISHER]

In this paper, a real-time implementation of selective harmonic elimination pulsewidth modulation (SHEPWM) using generalized Hopfield neural network (GHNN) as applied to the single-phase inverter is designed and discussed. Finding the location of the switching instants in the case of SHEPWM involves the solution of a set of nonlinear algebraic transcendental equations. The problem is redrafted as an optimization problem, and it is solved by using GHNN. Though, in principle, the $n$ number of harmonics can be eliminated using the presented methodology, this paper tries for the case of the elimination of the 5th-, 7th-, 11th-, and 13th-order harmonics while retaining the desired fundamental. An energy function is formulated for this problem and the set of ordinary differential equations (ODEs) describing the behavior of GHNN is obtained. A program in KEIL C was developed to solve these systems of ODEs by the Runge–Kutta fourth-order method to give the switching instants for continuously varying modulation indexes $(M)$. A MATLAB simulation was carried out, and an experimental setup was also constructed in order to validate the simulated results. The fast Fourier transform analysis of the simulated output voltage waveform and the experimental output voltage waveform confirms the effectiveness of the proposed method. Hence, the proposed method proves that it is much applicable in the industrial applications by virtue of its suitability in real-time applications. [ABSTRACT FROM PUBLISHER]

Impedance network inverters are the best alternatives for voltage-source and current-source inverters. The boosting capability and the shoot-through solution of such converters make them excellent solutions for various applications. Nevertheless, hard switching forces the converter to operate in low switching frequency, which results in a bulky impedance network. Moreover, the coupling between the shoot-through duty cycle and the inverter modulation index makes a tradeoff between the voltage gain and the modulation index (output voltage harmonics). This paper presents a novel dual switching frequency modulation to mitigate the switching losses of the converter, which results in a more compact impedance network. The proposed method combines a high-frequency pulse width modulation with a low-frequency sinusoidal pulse width modulation (SPWM). Therefore, the switching losses decrease considerably with respect to the conventional simple boost modulation. In addition, the impedance network design frequency remains high, and the network size decreases obviously. The proposed approach removes the interdependence between the shoot-through duty cycle and the inverter modulation index. A comparison between the proposed method and the conventional simple boost method is performed to show its advantages over the conventional method. Finally, experimental results are presented to validate the performance of the proposed method. [ABSTRACT FROM PUBLISHER]

In this paper, a dc-link voltage protection (DCVP) control method is proposed to address the dc-link overvoltage issue due to power backfeeding in a parallel uninterruptible power supply (UPS) system. The proposed control method is able to protect the inverter against the excessive dc-link voltage, which increases the system reliability and robustness. Moreover, a current sharing control strategy is proposed by online regulating the virtual resistance of each UPS module. The proposed current sharing control strategy is able to address the circulating fundamental and harmonic currents caused by the line impedance mismatching or power backfeeding issue in the UPS system. In addition, an improved consensus-based distributed controller is proposed to alleviate the overshoot issue during the transient process in voltage amplitude and frequency restoration. Finally, the feasibility of the proposed methods is verified by experimental results from the parallel UPS prototypes. [ABSTRACT FROM PUBLISHER]

Traditional model predictive control cost functions, when utilizing long prediction horizons ( $N\geq 10$) in power inverter applications, have demonstrated harmonic performances approaching that of schemes based on offline-generated optimal pulse patterns. However, long prediction horizons often prohibitively increase computational load. A different approach to maximizing harmonic performance is taken in this paper. It is shown that shaping the output voltage spectra using a simple feedback mechanism can significantly reduce the length of the required prediction horizon, facilitating a feasible computational load. When a short-horizon cost function is augmented by the feedback mechanism an excellent tradeoff between harmonic performance and switching loss is achieved, even with a prediction horizon of one. It is also shown that the feedback mechanism can be used to improve input reference tracking. Experimental verification of the proposed modulator is performed on a two-level three-phase inverter. [ABSTRACT FROM AUTHOR]

In this paper, a fault-tolerant multiphase multilevel inverter (MPMLI) configuration is proposed based on the dual inverter concept. This configuration helps to improve the performance of pole–phase modulated multiphase induction motor (PPMMIM) drive in both normal and switch failure conditions. Comparing to the existing multilevel inverter topologies for multiphase induction motor (MIM) drives, the proposed MPMLI configuration requires less number of dc sources and power electronic devices. The proposed MPMLI configuration is able to sustain under various faulty conditions, which can improve the reliability of the system. In addition, dc-link utilization (DLU) in low-pole mode is improved by using space vector pulsewidth modulation (SVPWM). In high-pole mode, carrier-phase-shifted 3-Φ SVPWM is used for reducing the torque ripple. This MPMLI configuration produces a multilevel voltage profile across the effective phase in 3-phase 12-pole mode. By maintaining the V/f ratio constant, the proposed MPMLI-fed MIM drive facilitates a wide range of load torque with half of the rated speed in faulty condition. This advantage makes it suitable for traction and electric vehicle applications where reliability and wide range of torque–speed are the major concerns. The performance of proposed MPMLI-fed 5 hp, 9-φ PPMMIM drive is simulated by finite-element method (FEM) in ANSYS Maxwell 2-D and experimentally verified by laboratory prototype under normal and faulty conditions. [ABSTRACT FROM PUBLISHER]

In this paper, a new carrier-based pulse width modulation (PWM) strategy providing common-mode voltage (CMV) elimination and reduced current ripple in a three-level neutral-point-clamped inverter is introduced. The employed switching sequences are made up of the three zero CMV (ZCMV) vectors, and one among the three vec-tors is applied at two ends of a half-carrier cycle. The output current ripple characteristics pertaining to those switching sequences are investigated. In a carrier cycle, the root-mean-square current ripple minimization is analyzed and an optimal sequence is derived accordingly. The presented PWM scheme results in a considerably reduced current harmonic distortion in a wide modulation region as compared to the two existing ZCMV schemes on the same average switching frequency. Also, an implementation of sawtooth-carrier-based PWM patterns is proposed for further improvement of the harmonic performance. The algorithm requires small computational burden and is straightforward for an online implementation. Simulation and experimental results are both provided to validate the good performance of the proposed PWM method. [ABSTRACT FROM PUBLISHER]

This paper presents the mathematical and harmonic analyses of output phase voltages of three-phase voltage source inverters which employ a hybrid two-dimensional–threedimensional (2-D–3-D) space vector modulation (SVM) voltage control algorithm. The explicit time-domain representation of the harmonic components in addition to the total harmonic distortion (THD) of the output phase voltages is given in terms of system and control parameters. This paper also investigates the harmonic characteristics and THD performance against the linearity of the modulation region which helps in the harmonic performance and design studies of such inverters employing the hybrid 2-D–3-D SVM. The fundamental component of the output voltages follows the reference with lower THD in the linear modulation region rather than the overmodulation region. Experimental results are used to validate these analyses as well as the effectiveness of the hybrid 2-D–3-D SVM algorithm for generating balanced and low THD phase voltages. [ABSTRACT FROM PUBLISHER]

This paper presents a new high-frequency modulation method for multilevel converters. The proposed method provides a broad linear operating range and can be digitally implemented with minimal computational effort. This modulation method creates a phase voltage composed of a rectangular component superimposed on the top of a quasi-square-shaped reference function. The reference functions are defined such that the utilization of the dc-link voltage is maximized in any modulation index, while the dv/dt of the switches is always the minimum possible value. In order to implement the proposed method, an update time that is much shorter than the fundamental period is defined in the algorithm for updating the rectangular components of the reference voltage. The high-frequency rectangular component can then be imposed on the reference function to generate the final switching function by switching between two voltage levels during the time between two update instances. Several experimental results are provided to evaluate the performance of the proposed method and to compare its operation to conventional methods. [ABSTRACT FROM PUBLISHER]

In this paper, the near-state pulse width modulation (NSPWM), adapted to be used in dual-voltage source inverter (VSI) fed open-end load, is introduced primarily aiming to appreciably minimize the voltage total harmonic distortion (THD). Within the framework of the proposed method, the active time of pulses at the second inverter is relatively adjusted within switching interval (compared to the first VSI). The phase voltage harmonics are formulated for dual-inverter modulated by NSPWM; then, optimal adjustment is identified via a three-dimensional curve of phase voltage THD versus modulation index (MI) and phase angle displacement (PAD). Due to the limitation of MI in NSPWM, the desired output voltage is synthesized with modifying not only MI but also PAD between references of two VSIs. Furthermore, NSPWM inherently takes advantage of better efficiency compared to conventional space vector modulation due to switching only two phases within an interval (by clamping one phase to positive/negative dc-rail). The dual-VSI supplied by two isolated dc sources is assembled in the laboratory to experimentally evaluate the THD reduction feature of the proposed method; also, the simulation results obtained by means of a MATLAB/Simulink environment show close agreement with experimental data. [ABSTRACT FROM PUBLISHER]

In grid-connected inverters, a feedforward controller accurately compensates for a large number of the harmonic components of the injected current. This controller is fast and directly tackles the grid dynamic voltage disturbances without doing any further harmonic analysis. A feedforward controller was introduced to a three-phase grid connection with a wye configuration; however, for the widespread delta connections, such a scheme is less established. Moreover, the nonsinusoidal profile of the grid voltage waveform makes the online conversion of line-to-line values into phase values impossible. In this paper, implicit zero-sequence discontinuous pulse width modulation (IZDPWM) based feedforward control is implemented on the two-level grid-connected inverter. Regardless of the grid topology, the IZDPWM-based controller ensures sinusoidal current injection to the grid under balanced, unbalanced, and distorted conditions. [ABSTRACT FROM PUBLISHER]

Multilevel active neutral-point-clamped (ANPC) converter is popularly known for its higher medium voltage drives up to 6.9 kV. However, common-mode voltages (CMV) are generated when using the well-established carrier-based pulse width modulation (PWM) modulation technique. As a result, CMV will become the major cause of the premature bearing failures and the conducted electromagnetic interferences. In this paper, a reduced CMV strategy is proposed for the ANPC which employs an alternatively new hybrid carrier-based modulation named as interleaved sawtooth carrier phase-disposition PWM (ISC-PD-PWM). By doing so, enhanced harmonic profile is achieved as compared to the typically used classical phase-shifted carrier PWM (PSC-PWM). Therefore, a comparative evaluation of the seven-level (7L) ANPC performance using the proposed reduced CMV approach is made between the novel hybrid ISC-PD-PWM and the conventional PSC-PWM in terms of harmonic analysis. The experimental results have proven the feasibility of the proposed concepts with the CMV effectively reduced. Such perceived merits make ANPC be more attractive for its motor drives. [ABSTRACT FROM AUTHOR]

This paper proposes a new configuration for static ground power unit (GPU) based on the novel 25-level hybrid active neutral-point-clamped (HANPC) converter. The superiority of the proposed converter, as compared with conventional and other suggested multilevel converters, is significant decreasing the number of switches and minimizing the number of flying capacitors (FC) in converter. This improvement is possible by using suggested low-voltage submodule converter to the ANPC converter and proposed modulation method. This results in reduction of the size and cost of converter and makes it more feasible and reliable. Applying the active voltage balancing method for FC in the proposed HANPC converter guaranties fast charging and voltage-level regulation of FC without using balance booster circuit. Improving output voltage spectrum leads to inductance reduction of output L–C filter which enhances static GPU performance. The simulation and experimental results verify the validity and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, a novel cascaded seven-level inverter topology with a single input source integrating switched-capacitor techniques is presented. Compared with the traditional cascade multilevel inverter, the proposed topology replaces all the separate dc sources with capacitors, leaving only one H-bridge cell with a real dc voltage source and only adds two charging switches. The capacitor charging circuit contains only power switches, so that the capacitor charging time is independent of the load. The capacitor voltage can be controlled at a desired level without complex voltage control algorithm and only use the most common carrier phase-shifted sinusoidal pulse width modulation strategy. The operation principle and the charging–discharging characteristic analysis are discussed in detail. A 1-kW experimental prototype is built and tested to verify the feasibility and effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper presents a hybrid selective harmonic mitigation (SHM)-selective harmonic elimination (SHE) switching technique based on pulse-amplitude modulation (PAM) concept. It has been applied on a four-leg neutral-point-clamped (NPC) inverter to eliminate and mitigate more harmonic orders than recently proposed hybrid SHM-SHE-pulse width modulation (PWM) method while generating switching pulses at the same frequency. In conventional SHE and SHM techniques, equations are solved to attain the switching angles. Regarding the PAM, value of inverter dc voltage can be considered as an additional degree of freedom by which the flexibility of such techniques would be increased maintaining the switching frequency. In the proposed SHM-SHE-PAM, the conventional equations are reformulated to obtain constant switching angles for a vast range of modulation index (ma) applied on a four-leg NPC inverter. Switching pulses of the three-phase legs and the fourth leg are calculated to mitigate the nontriplen harmonics and eliminate the triplen ones, respectively. Due to the unique switching angles valid in the whole range for ma, the calculation time and volume (storage capacity) are significantly reduced leading to a simpler controller implementable on a low-risk and cheap AVR chip. Experimental tests’ results of a four-leg NPC inverter as UPS application prove the good dynamic performance and accuracy of the proposed implemented switching technique in producing associated pulses for the inverter switches at very low frequency to mitigate/eliminate undesired harmonic orders from the output phase/line voltage waveforms without using bulky filters. [ABSTRACT FROM AUTHOR]

This paper presents a new E-type module for asymmetrical multilevel inverters (MLIs) with reduced components. Each module produces 13 levels with four unequal dc sources and 10 switches. The design of the proposed module makes some preferable features with a better quality than similar modules such as the low number of semiconductors and dc sources and low switching frequency. Also, this module is able to create a negative level without any additional circuit such as an H-bridge, which causes reduction of voltage stress on switches. Cascade connection of the proposed structure leads to a modular topology with more levels and higher voltages. Selective harmonics elimination pulse width modulation (SHE-PWM) scheme is used to achieve high-quality output voltage with lower harmonics. MATLAB simulations and practical results are presented to validate the proposed module good performance. Module output voltage satisfies harmonics standard (IEEE519) without any filter in output. [ABSTRACT FROM AUTHOR]

This paper presents a harmonic elimination technique based on a three-level dodecagonal space vector structure for open-end winding induction motor (IM) drives with a single-dc supply. Advantages of dodecagonal space vector switching and multilevel inverters are achieved with a single-dc supply. A dc supply-fed three-level flying capacitor (FC) inverter feeds active power to one end of the IM winding terminals and H-bridge connected capacitors eliminate fifth- and seventh-order harmonics from the other end. A pulsewidth modulation (PWM) technique is developed to switch the three-level dodecagonal space vectors and simultaneously control the H-bridge capacitors at 0.1445V\text{dc}. The fifth- and seventh-order harmonics are eliminated for the full modulation range of the three-level FC inverter, including the extreme 6-step operation. An increase in the linear modulation range has been achieved, resulting in improved dc bus utilization. Harmonic elimination is achieved by increasing switching frequency of the low-voltage capacitor connected H-bridge inverter; thus, switching frequency for the high-voltage dc supply-fed FC inverter is not increased. Using the proposed scheme, the instantaneous phase voltage never exceeds \frac23V\text{dc} (maximum phase voltage applied for hexagonal space vector structure) for which the machine windings are rated. Additionally, the proposed inverter has also been shown to operate for field oriented control of the open-end winding IM drive. [ABSTRACT FROM AUTHOR]

Multilevel converters have received more attention recently. Multilevel converters can be used not only in high-voltage high-power applications, but also in energy storage systems, thanks to reduced harmonics and electromagnetic interferences. State-of-charge (SoC) balancing of the storage system cells within cascaded multilevel inverters, e.g., batteries, can be one of the challenges in practical applications. Different methods have been studied and reported in technical literature. However, the SoC balancing is still a challenging issue. In this paper, a new method is proposed to solve this problem by applying several clever but simple changes to the staircase modulation switching scheme without changing the output waveform properties. Validations for this simple method were performed through simulation and experimental prototype. Despite the simplicity of the method, the simulation and experimental results show that SoC balancing of the cells has significantly improved. [ABSTRACT FROM PUBLISHER]

This paper addresses theoretical calculation of a single-phase multilevel pulsewidth modulation (PWM) inverter current total harmonic distortion (THD). Analytical approach introduced in late 1980s for a two-level inverter is generalized for an arbitrary level count for a single-phase inverter. Although the obtained closed-form piecewise analytical solutions assume (infinitely) large ratio of switching and fundamental frequencies and pure inductive load, they are practically very accurate for the ratios of (apparent) switching and fundamental frequencies larger than 25–30 and inductance-dominated loads. Along with strict mathematical solutions, simple accurate Bessel function approximation and hyperbolic average trend one are suggested. The formulas clearly reveal a single-phase PWM inverter current THD dependence on modulation index for an arbitrary voltage level count and are easily modified to cover grid-connected cases. [ABSTRACT FROM PUBLISHER]

The cost reduction of power-electronic devices, the increase in their reliability, efficiency, and power capability, and lower development times, together with more demanding application requirements, has driven the development of several new inverter topologies recently introduced in the industry, particularly medium-voltage converters. New more complex inverter topologies and new application fields come along with additional control challenges, such as voltage imbalances, power-quality issues, higher efficiency needs, and fault-tolerant operation, which necessarily requires the parallel development of modulation schemes. Therefore, recently, there have been significant advances in the field of modulation of dc/ac converters, which conceptually has been dominated during the last several decades almost exclusively by classic pulse-width modulation (PWM) methods. This paper aims to concentrate and discuss the latest developments on this exciting technology, to provide insight on where the state-of-the-art stands today, and analyze the trends and challenges driving its future. [ABSTRACT FROM PUBLISHER]

In this paper, a new inverter topology is proposed for generating a multilevel dodecagonal voltage space vector structure for open-end winding induction motor (IM) using a single dc source. Dodecagonal voltage space vector structure eliminates fifth- and seventh-order harmonic voltages from phase voltage output and hence eliminates the fifth- and seventh-order harmonic currents through the motor leading to removal of the dominant sixth-order torque ripple generation in the motor over the entire modulation range. Multilevel space vector structure generates output voltage with better THD and low dv/dt. In the proposed topology, two three-level inverters drive an open-end winding IM, one inverter from each side. DC-link of primary inverter is from a dc source which delivers the entire active power, whereas the secondary inverter dc-link is maintained by a capacitor, which is self balanced during the inverter operation. The PWM scheme implemented ensures low switching frequency for primary inverter. Secondary inverter operates at a small dc-link voltage. Hence, switching losses are small for both primary and secondary inverters. Experimental results show the elimination of fifth- and seventh-order harmonic voltages over the entire modulation range, validating effectiveness of the proposed multilevel inverter scheme. [ABSTRACT FROM PUBLISHER]

In an electric drive vehicle (EDV), the available voltage on a dc-link is limited, and so the inverter output voltage and, consequently, the line motor maximum speed are limited. The fundamental voltage of the inverter output is increased approximately 27% using a square wave (SW) switching pattern instead of a sine wave switching pattern. However, this pattern can only be used at high speeds, and at lower speeds a pulsewidth modulation (PWM) pattern should be used. In order to achieve proper control, the switching pattern should be changed seamlessly. In the present paper, a new PWM scheme for single-mode seamless control of Vernier motors is proposed. In the proposed scheme, the reference voltage is modified to change the switching pattern continuously so that the voltage changes smoothly from a high-frequency pattern to an SW and voltage discontinuity does not occur. Experimental results reveal that the inverter-switching pattern changes smoothly from a sinusoidal PWM pattern to an SW pattern, and so seamless control from the constant-torque region to the constant-power region, and vice versa, is achieved. Since the proposed scheme is a single-mode control, it is much simpler than current technologies, which are based on multimode controllers. Also the proposed method has a lower total harmonic disturbance (THD) as well as a lower harmonic distortion factor (HDF) compared to some existing methods. [ABSTRACT FROM PUBLISHER]

Multilevel inverters are gaining more attention in ac drive application due to their many attractive features. In the case of conventional neutral-point-clamped (NPC) or flying capacitor multilevel inverter configurations, active switches are connected in series to produce multilevel output voltage waveform. Therefore, if any one switch fails, the entire configuration has to be shut down; this will reduce the reliability of the system. A dual three-level inverter configuration for induction motor drive is proposed in this paper to improve reliability of the system. This topology is developed by feeding four-pole induction motor stator winding with four conventional two-level inverter modules. A level-shifted carrier-based third harmonic injection pulsewidth-modulation technique is used to produce the gating signals for the proposed configuration. By providing proper phase shift between carrier waves, multilevel voltage waveform is produced across the total motor phase winding, and first center band harmonics are also canceled. Thereby, the torque ripple will be considerably reduced compared with conventional NPC five-level inverter-driven induction motor drive. Finite-element analysis (FEA) is used to estimate the torque ripple when induction motor is supplied by the proposed configuration and conventional five-level NPC inverter configuration to show the effectiveness of the proposed converter. The proposed configuration is simulated using MATLAB/Simulink and experimentally verified using a laboratory prototype with a 5-hp four-pole induction motor drive. [ABSTRACT FROM PUBLISHER]

In this paper, three overmodulation techniques for the three-to-five-phase indirect matrix converter (IMC) are proposed. The first technique utilizes only the adjacent large vectors in the sector in which the reference output voltage vector lies. The second technique improves on that by continuously adapting vector elimination in the d_2-q_2 vector space based on the output voltage requirements. The third technique utilizes the ripple in the dc link to further reduce the modulation index of the inverter stage during overmodulation. All three techniques increase the voltage transfer ratio of the three-to-five-phase IMC from 0.788 to 0.923, but with the addition of harmonics generated by a vector in the d_2-q_2 vector space of the inverter stage. Simulation and experimental results from a prototype three-to-five-phase IMC validate the three proposed overmodulation techniques. [ABSTRACT FROM AUTHOR]

In this paper, a multilevel dodecagonal voltage space vector structure with nineteen concentric dodecagons is proposed for the first time. This space vector structure is achieved by cascading two sets of asymmetric three-level inverters with isolated H-bridges on either side of an open-end winding induction motor. The dodecagonal structure is made possible by proper selection of dc link voltages and switching states of the inverters. The proposed scheme retains all the advantages of multilevel topologies as well as the advantages of dodecagonal voltage space vector structure. In addition to that, a generic and simple method for calculation of pulsewidth modulation timings using only sampled reference values ( $v_\alpha$ and $v_\beta$) is proposed. This enables the scheme to be used for any closed-loop application such as vector control. In addition, a new method of switching technique is proposed, which ensures minimum switching while eliminating the fifth- and seventh-order harmonics and suppressing the eleventh and thirteenth harmonics, eliminating the need for bulky filters. The motor phase voltage is a 24-stepped waveform for the entire modulation range thereby reducing the number of switchings of the individual inverter modules. Experimental results for steady-state operation, transient operation, including start-up have been presented and the results of fast Fourier transform analysis is also presented for validating the proposed concept. [ABSTRACT FROM PUBLISHER]

This paper proposes a technique to suppress low-order harmonics for an open-end winding induction motor drive for a full modulation range. One side of the machine is connected to a main inverter with a dc power supply, whereas the other inverter is connected to a capacitor from the other side. Harmonic suppression (with complete elimination of fifth- and seventh-order harmonics) is achieved by realizing dodecagonal space vectors using a combined pulsewidth modulation (PWM) control for the two inverters. The floating capacitor voltage is inherently controlled during the PWM operation. The proposed PWM technique is shown to be valid for the entire modulation range, including overmodulation and six-step mode of operation of the main inverter. Experimental results have been presented to validate the proposed technique. [ABSTRACT FROM PUBLISHER]

In this paper, selective harmonic mitigation (SHM) and selective harmonic elimination (SHE) modulation techniques have been combined to produce appropriate pulses for a four-leg three-level neutral point clamped (NPC) inverter. In the proposed hybrid method, the SHM technique is applied to phase legs in order to mitigate non-triplen harmonics (fifth, seventh, $\ldots$) , and the fourth leg is controlled by the SHE principle to eliminate important low-order triplen harmonics (third, ninth, $\ldots$) completely. In this context, it is demonstrated that using SHM instead of an SHE modulator for phase legs leads to a reduced vast range of harmonic orders in the NPC output voltage, significantly. Moreover, it is proved that the presented hybrid switching technique has the ability of dc-bus capacitor voltage balancing, inherently. Furthermore, analyses are performed to calculate the dc-bus capacitances accurately to show 5% voltage ripple acceptably. Simulation and experimental results validate a good dynamic performance of the proposed hybrid modulation technique in firing the NPC inverter switches to generate low-harmonic voltage waveforms supplying balanced and unbalanced loads while balancing the dc capacitor voltages in a four-wire network with small dc-link capacitors. [ABSTRACT FROM PUBLISHER]

Power converters using deterministic switching frequency schemes have switching noise concentrated at harmonic frequencies, resulting in enhanced electromagnetic emission. To suppress the harmonic spikes in three-phase multilevel voltage source converters, a digital control scheme based on dithered sigma–delta modulation (SDM) is proposed in this paper. Introducing a dithered sequence in an SDM varies the switching frequency randomly, resulting in the suppression of the spurious harmonic spikes in the output spectrum even with a regular control input. Although the switching frequency varies randomly, the minimum pulsewidth of the proposed scheme is the sampling time period, avoiding the minimum pulsewidth problem. Instead of a conventional scalar quantizer, the quantizer in the proposed dithered sigma–delta converter uses the principle of space vector quantization. The proposed scheme is experimentally verified on a constant $v/f$ open-loop induction motor drive for a three-level inverter realized by cascading two two-level inverters. The performance of the proposed scheme is compared with different pulsewidth modulation schemes in the entire modulation index, including the overmodulation region. [ABSTRACT FROM PUBLISHER]

Many recent multilevel inverter papers end up with voltage total harmonic distortion (THD) values obtained from numerical voltage spectrum calculations (measurements). Motivated by IEEE Standard 519, a part of the multilevel research community uses a limited harmonic count to evaluate the multilevel voltage quality. First, this causes significant voltage THD underestimation, particularly for relatively high frequency PWM. Second, for a three-phase star-connected balanced load with an isolated neutral and phase symmetric modulation strategy, the calculated load line and phase voltage THD become different. However, simple considerations show that line and phase voltage THDs are essentially the same in this case. It may be difficult to judge about the multilevel voltage quality given a numerically calculated (measured) voltage THD value that may be subject to computation errors. Presented are simple smooth hyperbolic voltage THD upper and lower bound approximations for single- and three-phase inverters with nearest synchronous switching. They are valid for arbitrary modulation indices and uniformly distributed level counts and may practically serve as good reference values. [ABSTRACT FROM PUBLISHER]

One of the most important power quality issues is related to current harmonics generated by nonlinear loads such as diode and thyristor front-end rectifiers. Well-established solutions to overcome this problem, such as active power filters (APFs), have the required high power rating components as a major disadvantage. An alternative, called hybrid power filter (HPF), mixes low power rating active filters with passive filters. Unfortunately, many of these HPF topologies have, as a common disadvantage, a great number of passive components and/or transformers. Based on this fact, new concepts of HPFs, consisting of small-rated inverters and $LC$ filters, have been introduced with wide acceptance. The advantage comes from the fact that these HPFs are connected to the grid without any matching transformer. Recently, some topologies based on dual-converter configurations have been shown to be very attractive, where the APF (or HPF) must deal with highly nonlinear loads with high values of $di/dt$ and supplying the reactive power together with harmonic compensation. On the other hand, the drawback of dual converters is the high number of switch devices. Therefore, this paper proposes a transformerless HPF based on a new six-switch two-leg inverter with an enhanced harmonic compensation capability. Aside from presenting a reduced number of switches when compared with dual topologies, the proposed solution is capable of providing fully compensation even for loads with high harmonic content. Experimental results are presented for an HPF inverter prototype in order to demonstrate that the harmonic compensation performance meets the IEEE 519 standard. [ABSTRACT FROM PUBLISHER]

This paper presents an analytical method that makes it possible to define the pulsewidth modulation (PWM) supply output voltage spectral content, particularly the harmonic phase sequences, without switching instant determination. The results obtained from these developments lead to define a PWM control strategy that allows deleting some switching harmonics in order to reduce undesirable effects. Numerical studies and experiments confirm the theoretical approach and this harmonic control strategy. [ABSTRACT FROM PUBLISHER]

The term dead time refers to a prime safety factor for most power electronic converter topologies, and it is included either in the control software or in the gate/base driver hardware, depending on the application as well as the control requirements. In this paper, the authors present a comprehensive numerical analysis of dead-time effects on the output voltage of a three-level neutral-point-clamped (NPC) inverter. To incorporate the dead-time effect in the output voltage, 3-D models of three-level carrier pulse width modulation (PWM) methods are modified for two dead-time implementations. Closed-form expressions of inverter phase voltage harmonics for phase opposition disposition (POD) PWM are derived based on the double Fourier series approach and modified contour plots. The harmonic spectra from numerical evaluations, simulations, and experiments for natural sampling (NS), symmetrical regular sampling (SRS), and asymmetrical regular sampling (ARS) are compared to validate the mathematical models. In addition, the fundamental voltage with respect to the dead time and the load phase angle is presented based on analytical results and simulation. [ABSTRACT FROM PUBLISHER]

The objective of this paper is to propose a new inverter topology for a multilevel voltage output. This topology is designed based on a switched capacitor (SC) technique, and the number of output levels is determined by the number of SC cells. Only one dc voltage source is needed, and the problem of capacitor voltage balancing is avoided as well. This structure is not only very simple and easy to be extended to a higher level, but also its gate driver circuits are simplified because the number of active switches is reduced. The operational principle of this inverter and the targeted modulation strategies are presented, and power losses are investigated. Finally, the performance of the proposed multilevel inverter is evaluated with the experimental results of an 11-level prototype inverter. [ABSTRACT FROM PUBLISHER]

This paper presents a division-summation (D-\Sigma) digital control for a three-phase inverter to achieve active and reactive power injection to the ac grid. The proposed D-\Sigma approach summarizes the inductor-current variations over one switching cycle to derive control laws directly, which can overcome the limitation of d–q transformation. The inverter with this control can achieve various power factors (PFs) leading or lagging, by taking into account wide filter-inductance variation and grid-voltage distortion, reducing core size significantly. The control laws for achieving the desired features are derived in detail, and they are expressed in general forms for readily software programming. With the enhancement work of previous research, active and reactive power injection with PF from 0 to 1 can be controlled effectively, so that these control laws can be extended to wide current-tracking applications, such as static synchronous compensator and active power filter. In the design and implementation, the inductance values corresponding to various inductor currents were measured at the startup and stored in the controller for scheduling loop gain cycle by cycle. Measured results from a 10-kVA 3 \phi inverter have confirmed the analysis and discussion of the proposed control approaches. [ABSTRACT FROM PUBLISHER]

The high-power voltage source inverters are switched at low frequency to reduce the losses in the inverter. The discontinuous pulsewidth-modulation (PWM) sequences reduce the switching frequency to two-thirds compared to the conventional continuous PWM sequences. At low switching frequency, the output will be rich in harmonics, and synchronization is a must to avoid subharmonics. This paper presents four basic types of synchronized discontinuous PWM (DPWM) sequences that ensure synchronization, three-phase symmetry, and half-wave symmetry. The proposed synchronized DPWM sequences are verified through simulation and experiment on a constant- v/f open-loop induction motor drive. The performance of the proposed DPWM algorithms is studied in the entire modulation region, including the overmodulation region, and is compared with that of the conventional synchronized space vector PWM. A different type of DPWM with low common-mode voltage is suggested for low-modulation region and verified experimentally. [ABSTRACT FROM PUBLISHER]

Loads connected to a stiff source cannot be protected from voltage disturbances using a distribution static compensator (DSTATCOM). In this paper, a new control-algorithm-based multifunctional DSTATCOM is proposed to operate in voltage control mode under stiff source. This scheme provides fast voltage regulation at the load terminal during voltage disturbances and protects critical loads. In addition, during normal operation, the generated reference load voltages allow control of the source currents. Consequently, DSTATCOM injects reactive and harmonic components of load currents to make source power factor unity. Simulation and experimental results are presented to verify the efficacy of the proposed control algorithm and multifunctional DSTATCOM. [ABSTRACT FROM PUBLISHER]