Search

This paper proposes a capacitor voltage regulation method for the dual converter with a floating bridge for aerospace applications. This topology has previously been reported, but with a constrained voltage utilization factor due to the need for capacitor voltage regulations. In this paper, the effect of switching states on the voltage variation of capacitor is quantitatively modeled and an enhanced space vector modulation scheme with current feedback is proposed to achieve an active control of the floating capacitor voltages. This proposed method also allows further exploitation and utilization of converter voltage. The relationship between the allowed modulation index of dual converter and load power factor is obtained and expressed using a fitted polynomial equation. The advantages of the proposed method include boosted voltage utilization and superior performance in term of capacitor voltage balance. These advantages have been proven through simulation and experimental results on RL loads as well as with an open-end winding induction motor. The proposed modulation scheme can boost the converter voltage utilization by at least 10% while achieving full four-level operation. More importantly, the higher available voltage allows extending the constant torque region of the motor, the further beginning of field weakening operation could be postponed. [ABSTRACT FROM AUTHOR]

A trinary multilevel converter uses a few heterogeneous H-bridge submodules (SMs) to synthesize an output voltage with multiple levels. Two major limitations of this converter are that it needs multiple dc sources and it cannot operate under pulsewidth modulation (PWM). This paper addresses these limitations by adding a low-voltage H-bridge SM to this converter and proposing a new switching algorithm. The resulting PWM-based asymmetric cascaded H-bridge converter uses only one dc source and synthesizes a high-quality output voltage. This improved converter can be a potential choice for real and reactive power support in power system applications. This paper also proposes methods for stability analysis and design of this converter. Experimental case studies evaluate the performance of the proposed converter for both standalone and grid-connected modes of operation. [ABSTRACT FROM AUTHOR]

In this paper, a new structure for symmetric and cascade multilevel converter is presented. This structure requires the least power electronic components, gate driver circuits, power diode, and dc voltage source. The number of output levels is high. Reduction of the number of power electronic switches against voltage levels is an important factor in multilevel converters due to safety in switches, circuit size, cost, installation area, and complexity in control. To maximize the number of output level in the proposed optimized structure in order to attain different goals, such as reduction of stress on switches, the result of comparing the proposed structure and other structures present. The proposed method is robust against the switching faults in multilevel converter for dc source and the equipment. The simulation and experimental results presented in this paper show the performance of the proposed method. [ABSTRACT FROM AUTHOR]

The large number of semiconductors typically implemented in multilevel converters generates large stray inductances in their commutation loops. As a consequence, high-voltage overshoots appear in the semiconductors during commutation which may limit the operation of the converter. The paper analyzes these overvoltages in the five-level active neutral-point-clamped (5L­ANPC) converter, one of the most popular five level converters and employed by ABB in its ACS­2000 drive. Experimental results show overvoltages almost three times higher than those corresponding to a two-level converter. In order to overcome this problem, the paper presents a new 5L­ANPC with the same characteristics (number of semiconductors, output waveform, switching frequency, efficiency, etc.), but with smaller overvoltages. This is achieved by adding some small capacitors to the busbar that behave like lossless snubbers but with a much simpler implementation. The experimental results illustrate the working principle of these capacitors and demonstrate the reduction of the overvoltages. As a result, the new converter can reach a higher output current or speed-up the commutations reducing, therefore, the losses and increasing the efficiency compared with the previous 5L­ANPC. [ABSTRACT FROM AUTHOR]

This paper presents a new reconfiguration module for asymmetrical multilevel inverters in which the capacitors are used as the dc links to create the levels for staircase waveforms. This configuration of the multilevel converter makes a reduction in dc sources. On the other hand, it is possible to generate 13 levels with lower dc sources. The proposed module of the multilevel inverter generates 13 levels with two unequal dc sources (2VDC and 1VDC). It also involves two chargeable capacitors and 14 semiconductor switches. The capacitors are self-charging without any extra circuit. The lower number of components makes it desirable to be used in wide range of applications. The module is schematized as two back-to-back T-type inverters and some other switches around it. Also, it can be connected as a cascade modular which leads to a modular topology with more voltage levels at higher voltages. The proposed module makes the inherent creation of the negative voltage levels without any additional circuit (such as H-bridge circuit). Nearest level control switching modulation scheme is applied to achieve high-quality sinusoidal output voltage. Simulations are executed in MATLAB/Simulink and a prototype is implemented in the power electronics laboratory in which the simulation and experimental results show a good performance. [ABSTRACT FROM AUTHOR]

Many different topologies based on the multilevel converter approach have been presented in the last decades. In order to obtain improved output waveforms, several modulation techniques have been developed for such converters. Some of those modulation schemes can be directly applied to almost any multilevel converter, while others require significant adaptation in order to be implemented in certain specific converters. This paper presents the implementation of a phase-disposition level-shifted pulsewidth modulation to the recently introduced hybrid multicell converter (HMC). The HMC uses a flying capacitor module on each cell to generate a positive variable dc-link voltage. The variable dc link is inverted at fundamental switching frequency by an H-bridge to generate the cell output voltage. It is desirable to use PD-PWM for its well-known high-performance waveforms. In this paper, a state-machine decoder is developed to balance the floating capacitor voltages and to equalize the supplied power for the series-connected cells of the HMC when using a PD-PWM pattern. Experimental results obtained from a 10-kW prototype are presented, confirming the good-quality waveforms of the HMC modulated with PD-PWM and the adequate balance of all floating capacitors. [ABSTRACT FROM PUBLISHER]

Modular multilevel converter (MMC) is a newly emerging multilevel topology for high-voltage applications during recent years. In this paper, a new MMC is proposed, and the structure and operating principle are analyzed. Owing to the cascaded basic cells without multiwinding transformer, the voltage balancing of floating capacitors must be considered. However, the voltage fluctuation also exists, and theoretical analysis indicates that the amplitude is inversely proportional to the fundamental frequency. This paper has proposed a voltage-fluctuation-suppression method which can reduce the amplitude of the voltage fluctuation in low-frequency region. It can also be used in motor driving with pump/blowerlike load at low frequency and improve the start-up performance significantly. A low-power three-phase five-level prototype is designed and built up to demonstrate the validity of this method. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel high step-up nonisolated single switch dc–dc converter suitable for regulating dc bus in various microsources especially for photovoltaic (PV) sources. Quadratic boost and switched-capacitor technique are used as primary and secondary circuits, respectively. A coupled inductor is applied to make a connection between them, so a high dc voltage gain is achieved. High efficiency is yield where voltage stress on active switch is alleviated by clamped capacitor; consequently, smaller \rmR\rm{DS(ON)} for power switch is required. On the other hand, input current of the proposed converter is continued, hence stress on the input source is reduced. The operating principles and steady-state analyses are discussed in detail for both continuous and discontinuous conduction modes. Also, the boundary condition is computed. To verify the performance of the proposed converter and theoretical calculations, a 250-W prototype converter is implemented with an input voltage of 24 V and an output voltage of 400 V designed especially for PV sources in continuous conduction mode operation. Finally, simulation results are confirmed by experimental results; maximum efficiency is occurred at 150 W and full-load efficiency is 92.96%. [ABSTRACT FROM AUTHOR]

A new cascade topology for multilevel converter is introduced in this paper which comprises series connection of several submultilevel units. To determine the magnitudes of the dc sources, two new methods are described. The proposed topology is optimized to generate any levels with minimum number of components and peak voltage on switches. The presented topology can be used in high-voltage applications due to using the switches with low voltage rating. To indicate the merits of the proposed structure, comparison studies are provided with other topologies in terms of the number of elements and peak voltage on switches. The comparison results prove that the presented cascade multilevel converter requires fewer components. Moreover, it is shown that the total peak voltage on switches in the proposed topology is less than other structures. Experimental work is presented to demonstrate the performance of the presented multilevel converter. [ABSTRACT FROM PUBLISHER]

A novel complementary phase disposition pulsewidth modulation method for the modular multilevel converter (MMC) with a limited number of submodules is proposed in this paper. Compared with the previous works, more practical issues have been considered, and the corresponding solutions have been provided. First, a new preset PWM signal mapping sequence and an improved virtual loop mapping (VLM) are used in the modulation. This method not only achieves a favorable capacitor voltage balance in the symmetry system but lowers the switching frequency of MMC's devices. Second, to further reduce the switching frequency, the unbalance margin of capacitor voltages is adopted to achieve the switching between the VLM and the selective VLM (SVLM). Moreover, the system robustness has been improved by considering the situation of symmetry losing, like cell fails; in these cases, the capacitor voltages of the upper and lower arms are balanced through the collaboration of the SVLM and the reconfigurable VLM. Finally, the effectiveness of the proposed method has been verified with simulation and experimental studies. [ABSTRACT FROM AUTHOR]

In this paper, novel topologies for symmetric, asymmetric, and cascade switched-diode multilevel converter are proposed, which can produce many levels with minimum number of power electronic switches, gate driver circuits, power diodes, and dc voltage sources. The number of required power electronic switches against required voltage levels is a very important factor in designing of multilevel converter, because switches define the reliability, circuit size, cost, installation area, and control complexity. For asymmetric and cascade converter, new algorithms for determination of dc voltage sources values are presented. To produce maximum number of levels at the output voltage, the proposed cascade topology is optimized for different goals, such as the minimization of the number of power electronic switches, gate driver circuits, power diodes, dc voltage sources, and blocking voltage on switches. Comparison of the results of various multilevel converters will be investigated to reflect the merits of the presented topologies. The operations of the proposed multilevel converters have been analyzed with the experimental and simulation results for different topologies. Verification of the analytical results is done using MATLAB simulation. [ABSTRACT FROM PUBLISHER]