Search

The control loop stability in boost converters operating in continuous conduction mode has been restricted due to its nonminimum phase nature: the presence of a positive zero (right-half plane zero) in the control to output voltage transfer function. This paper proposes a method to mitigate the effect of the zero on the control loop by shifting the position of the zero to the left-half plane and hence leading to increased stability for the control loop of the boost converter. Superior performance of the proposed method has been clearly demonstrated using simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes a phase-shift interleaving control method for variable-phase switched-capacitor (SC) converters that can perform voltage conversions with little electromagnetic interference over a wide range of operating condition. This is achieved by having multiple units of SC converter connected in parallel and an N-state hysteresis unit selection control scheme which works along the interleaving control to vary the number of converters in operation. By having the capacitors of inactive units connected to the output and the converters operating with output interleaving operation, the output capacitor that is typically required in SC converters for maintaining a small voltage ripple is made redundant in this configuration. A three-unit SC converter of the proposed configuration is described in this paper. Experimental results show that the proposed solution works satisfactorily with good regulation, input and output interleaving operations, and dynamic response for a wide operating range. [ABSTRACT FROM PUBLISHER]

Single-phase power factor correction (PFC) ac–dc converters are widely used in the industry for ac–dc power conversion from single phase ac-mains to an isolated output dc voltage. Typically, for high-power applications, such converters use an ac–dc boost input converter followed by a dc–dc full-bridge converter. A new ac–dc single-stage high-power universal PFC ac input full-bridge, pulse-width modulated converter is proposed in this paper. The converter can operate with an excellent input power factor, continuous input and output currents, and a non-excessive intermediate dc bus voltage and has reduced number of semiconductor devices thus presenting a cost-effective novel solution for such applications. In this paper, the operation of the proposed converter is explained, a steady-state analysis of its operation is performed, and the results of the analysis are used to develop a procedure for its design. The operation of the proposed converter is confirmed with results obtained from an experimental prototype. [ABSTRACT FROM PUBLISHER]

In this paper, an improved model predictive control (MPC) of the modular multilevel converter (MMC) with reduced computational burden is proposed. A mathematical model of the MMC system based on the sum and difference of arm voltages are derived. Instead of determining the switching state of individual submodule (SM), the voltage levels of MMC are considered as control options based on the assumption that the SM capacitor voltages are well balanced. The further reduction of calculation effort is realized by using the tolerance band of capacitor voltages. The proposed MPC has a hierarchical structure. The cost function taking into account the ac-side current control, circulating current elimination and arm energy balancing is presented. The optimal voltage level, selected by the cost function, provides the voltage reference for the pulse width modulation modulator. The SM capacitor voltage balancing is done using a separate control loop. The proposed control strategy is investigated using an MMC high-voltage direct current system with 200 SMs in each arm in real-time simulation and hardware-in-the-loop tests. The performance of proposed method is verified by both steady-state and transient-state operations. [ABSTRACT FROM PUBLISHER]

A single-objective predictive control method that deals with four main control objectives applied to a multivariable single-phase three-level neutral-point-clamped converter operating as an active power filter is proposed in this paper. The four control objectives are to self-support the dc-bus voltage under load variations, to compensate the reactive power and the current harmonics, and to balance the dc capacitor voltages by using a predefined combination of the redundant switching states of the converter. The main contribution of the proposed method is that these objectives are accomplished without using weighting factors in the cost function, which eliminates problems such as multiobjective optimization or additional empirical procedures for determination of these factors. As a result, the method is easy to implement and rapidly selects the optimal voltage to improve the dynamic-state performance. Experimental results from a 2-kVA prototype are presented to prove that the method is valid for single-phase compensation. The well-known effect of model parameter errors' issue, which is inherent in predictive control methods, is also tested to confirm that the harmonic distortion in the grid current is below 5% even when the predictive model has a 25% error between actual and theoretically estimated grid impedance values. [ABSTRACT FROM PUBLISHER]

The modular multilevel converter (MMC) becomes attractive for medium- or high-power applications because of the advantages of high modularity, availability, and power quality. One of the technical challenges associated with an MMC is the balancing of the capacitors' voltages. In this paper, a voltage-balancing control method is proposed for the MMC under phase-shifted carrier-based pulsewidth modulation. The proposed voltage-balancing method uses the linearization method for pulse sorting without arm current measurement, which can control the capacitor charge transfer to balance the capacitor voltage in the MMC. In the proposed method, the voltagebalancing algorithm is implemented in each carrier wave period, which reduces the computational intensity and burden. In addition, the arm current can also be improved with the proposed method. The simulation studies with the professional tool PSCAD/EMTDC are conducted, and a downscale MMC prototype is also tested with the proposed method. The study results show the effectiveness of the proposed voltage-balancing method. [ABSTRACT FROM PUBLISHER]

This paper presents a power factor correction (PFC)-based bridgeless isolated Cuk converter-fed brushless dc (BLDC) motor drive. A variable dc link voltage of the voltage source inverter (VSI) feeding the BLDC motor is used for its speed control. This allows the operation of VSI in fundamental frequency switching to achieve an electronic commutation of the BLDC motor for reduced switching losses. A bridgeless configuration of an isolated Cuk converter is derived for the elimination of the front-end diode bridge rectifier to reduce conduction losses in it. The proposed PFC-based bridgeless isolated Cuk converter is designed to operate in discontinuous inductor current mode to achieve an inherent PFC at the ac mains. The proposed drive is controlled using a single voltage sensor to develop a cost-effective solution. The proposed drive is implemented to achieve a unity power factor at the ac mains for a wide range of speed control and supply voltages. An improved power quality is achieved at ac mains with power quality indices within the limits of the IEC 61000-3-2 standard. [ABSTRACT FROM PUBLISHER]

This paper analyzes the interleaved boost with coupled inductors (IBCI) converter, which is an isolated topology that is suitable for high step-up applications. Two main contributions are given: an exhaustive steady-state analysis and an accurate small-signal model. The former allows for deriving a closed-form noniterative design procedure for the power-stage active and passive components. In addition, it reveals an interesting equivalence with an apparently different converter, i.e., the single active bridge. Subsequently, the IBCI converter dynamic behavior is investigated, deriving a nonlinear average model that, under small-signal approximation, can be linearized around a given operating point and used for feedback controller design. A single photovoltaic module interface converter, rated for 300-W output power, is considered as a case study to validate the analysis outcome and the design procedure. Both are fully validated by measurements taken on the laboratory prototype. [ABSTRACT FROM PUBLISHER]

A single-switch nonisolated dc/dc converter for a stand-alone photovoltaic (PV)-battery-powered pump system is proposed in this paper. The converter is formed by combining a buck converter with a buck-boost converter. This integration also resulted in reduced repeated power processing, hence improving the conversion efficiency. With only a single transistor, the converter is able to perform three tasks simultaneously, namely, maximum-power-point tracking (MPPT), battery charging, and driving the pump at constant flow rate. To achieve these control objectives, the two inductors operate in different modes such that variable switching frequency control and duty cycle control can be used to manage MPPT and output voltage regulation, respectively. The battery in the converter provides a more steady dc-link voltage as compared to that of a conventional single-stage converter and hence mitigates the high voltage stress problem. Experimental results of a 14-W laboratory prototype converter with a maximum efficiency of 92% confirmed the performance of the proposed converter when used in a PV-battery pump system. [ABSTRACT FROM PUBLISHER]

This paper presents the hybrid seven-level cascaded active neutral-point-clamped (ANPC)-based multilevel converter. The converter topology is the cascaded connection of a three-level ANPC converter and an H-bridge per phase. The voltage of the H-bridge is actively maintained to the required level through selection of the switching states of the converter. The topology is operated under selective harmonic elimination pulsewidth modulation (SHE-PWM), maintaining the switching frequency of the converter to a minimum. The operating principles, voltage balancing methods, and limitations of the converter are analyzed together with extensive simulation results of the topology. Experimental results from a low-power laboratory prototype are presented that verify the operation of the hybrid converter under SHE-PWM. [ABSTRACT FROM PUBLISHER]