Search

A 1-MHz-modified single-ended primary-inductor converter (SEPIC) circuit is presented in this paper as an LED driver for automotive headlights. On the basis of traditional SEPIC, only a diode and two capacitors are added; therefore, the circuit structure is relatively simple and the volume is relatively small. High step-up capability is obtained with moderate duty cycle. Compared with traditional step-up circuit such as boost, low-voltage stress is gained which is beneficial to device selection. Zero-voltage switching is achieved at the same time to reduce switching loss. Planar inductors are used with the advantages of low profile and good thermal characteristic. Operational principle and parameters design process are introduced in detail. A 36-W prototype has been designed to demonstrate theoretical analysis. Obtained efficiency was up to 90.91% at full load. [ABSTRACT FROM AUTHOR]

In this paper, a family of automatic interleaved Dickson switched-capacitor converters (AIDSCC) and its zero-voltage switching (ZVS) resonant configuration are proposed. Different from the traditional Dickson switched-capacitor converter, the AIDSCC has symmetrical configuration with the features of automatic interleaved input current, small output voltage ripple, and lower peak capacitor voltage stress. To improve the line regulation capability, one small resonant inductor is inserted and two bulky capacitor banks are replaced by two much smaller resonant capacitors, forming the resonant AIDSCC. The transistors are ZVS turned on and diodes are zero-current switching turned off by operating above the resonance. With frequency modulation within a reasonable range, the voltage-gain range of the resonant AIDSCC is expanded significantly, while sacrificing the maximum efficiency due to the higher conduction loss. A 3X AIDSCC and a 3X resonant AIDSCC below 140 W were built to verify the analysis. [ABSTRACT FROM AUTHOR]

In this paper, a new family of zero-voltage-transition (ZVT) bidirectional converters are introduced. In the proposed converters, soft-switching condition for all semiconductor elements is provided regardless of the power flow direction and without any extra voltage and current stress on the main switches. The auxiliary circuit is composed of a coupled inductor with the converter main inductor and two auxiliary switches. The auxiliary switches benefit from significantly reduced voltage stress and without requiring floating gate drive circuit. Also, by applying the synchronous rectification to the auxiliary switches body diodes, conduction losses of the auxiliary circuit are reduced. In the auxiliary circuit, the leakage inductor is used as the resonant inductor and all the magnetic components are implemented on a single core which has resulted in significant reduction of the converter volume. In the proposed converters, the reverse recovery losses of the converter-rectifying diodes are completely eliminated and hence, using the low-speed body diode of the power switch as the converter-rectifying diode is feasible. The theoretical analysis for a bidirectional buck and boost converter is presented in detail and the validity of the theoretical analysis is justified using the experimental results of a 250-W prototype converter. [ABSTRACT FROM PUBLISHER]

A method for extending the duty cycle range of series-input interleaved forward converter (SII-FC) is proposed in this paper. A family of novel SII-FC topologies is derived by integrating two switching legs, which belong to two forward cells, into one switching leg shared by both the two forward cells in the SII-FC. By employing the proposed method, the derived topologies have the advantages of extended duty cycle, reduced components, and conduction losses, which help to achieve high power density and high efficiency. These advantages make the SII-FC topologies suitable for such applications with wide input voltage range. A series-input interleaved two-switch forward converter (SII-TS-FC) is analyzed in detail, which is a typical SII-FC topology developed by the proposed method. It is composed of two low-voltage switching legs and a high-voltage switching leg. Detailed analysis indicates that the maximum duty cycle of the SII-TS-FC can reach 2/3, which is 1.33 times of that of the two-switch forward converter. The switches of the high-voltage leg can be soft-switched when duty cycle is less than 0.5, while the switches of the low-voltage legs can be soft-switched when duty cycle is larger than 0.5. As a result, high efficiency is achieved over a wide voltage range. In addition, the output filter can be reduced due to the interleaving operation of the two forward cells. The operational principles, characteristics, and design considerations for the proposed SII-FC are presented. Experimental results on the SII-TS-FC prototype with 200–400 V input 48 V/12 A output verify the proposed method and analysis. [ABSTRACT FROM PUBLISHER]

This paper proposes a zero-voltage switching (ZVS) pulsewidth modulation (PWM) dc/dc converter with current double rectifiers to achieve ZVS for all switches under a wide range of load conditions and input voltages. Two three-level PWM circuits sharing the same power switches are adopted in the proposed converter to reduce the voltage stress of each MOSFET at Vin/2 and achieve load current sharing. Thus, the current stress and power rating at the secondary-side components are reduced. The current double rectifiers are used at the secondary side to partially cancel the output ripple current. Thus, the sizes of the magnetic components and output filter capacitance are reduced. Due to the resonant behavior by the resonant inductance and resonant capacitance at the transition interval, all switches are turned on at ZVS. The experimental results based on a 1-kW prototype are provided to verify the operation principle of the proposed converter. [ABSTRACT FROM PUBLISHER]