Search

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

A space vector modulation (SVM) technique of a dual-inverter system for an open-end winding motor drive is described in this paper, where one inverter has a battery power source and the other has an only capacitor across the dc bus. The SVM must be achieved to operate the motor with field-oriented control and simultaneously to control the capacitor voltage at a constant value by using redundant switching states of the dual-inverter system. The control of the capacitor voltage is carried out by selecting a charging or a discharging mode in each redundant switching state, taking the instantaneous motor power factor into account. In addition, it is also required to reduce the error voltage pulses, which are generated in output multilevel voltage waveforms during the dead time. The compensation method of the existing dead-time scheme and the improved SVM sequence to reduce the error voltage vectors are proposed in this paper. The proposed methods are examined through several experimental tests and are confirmed to generate superior output voltage waveforms from the viewpoint of the measured total harmonic distortion and dv/dt. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

In this paper, new half-bridge and full-bridge topologies for a switched-boost inverter are proposed. These topologies have a high boost factor in comparison with conventional types. In addition, the proposed topologies have continuous input current and can generate zero-voltage level in output. In this paper, the operation of the proposed inverters in different operating modes is analyzed. Then, the values of inductors and capacitors are designed. Moreover, the used switching pattern and its logical diagram are introduced. A comprehensive comparison between the proposed and conventional topologies in terms of the boost factor, the number of elements, and the efficiency shows the good features of the proposed inverters. Finally, to verify correct operation of the proposed topologies and derived equations, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

In this paper, two topologies are presented for the enhanced-boost quasi-Z-source inverters (qZSI), namely continuous input current configuration and discontinuous input current configuration of enhanced-boost qZSI with two-switched impedance networks. Similar to enhanced-boost impedance-source inverters (ZSIs), these proposed inverter topologies possess very high boost voltage inversion at low shoot-through duty ratio and high modulation index to provide an improved quality output voltage. Compared to enhanced-boost ZSIs with two-switched Z-source impedance networks, these proposed inverter topologies share common ground with source and bridge inverter, overcome the starting inrush problem, and draw continuous input current and the lower voltage across the capacitors. Moreover, the input ripple current is negligible. This paper presents the operating principles and analysis of continuous input current configuration enhanced-boost qZSI with two-switched impedance networks and compares with ZSI, switched inductor ZSI, DA/CA-qZSI, and enhanced-boost ZSIs. The theoretical analysis is done and is validated through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

A multilevel dodecagonal voltage space vector generation scheme for variable-speed drive applications with single-dc-link operation requires a large value of capacitance for cascaded H-bridge (CHB) filters, when operated at lower speeds. In existing schemes, the multilevel dodecagonal structure is obtained by cascading a flying capacitor inverter with a CHB. In this paper, a new scheme has been proposed to minimize the capacitance requirement for full speed operation by creating vector redundancies using modular and equal voltage CHBs. Also, an algorithm has been developed to optimize the selection of vector redundancies among the CHBs in order to minimize the voltage ripple of the floating capacitors. The proposed algorithm considers instantaneous capacitor voltages and phase currents for optimal selection of vector redundancies. A mathematical model for capacitor voltage deviation is presented, and the effectiveness of the proposed algorithm is verified in both the simulation and the experiment. [ABSTRACT FROM AUTHOR]

This paper deals with the analysis of the input dc-link voltage ripple in multilevel inverter based on H-bridge and level doubling network (LDN). The LDN is basically a half-bridge fed by a floating capacitor, with voltage self-balancing capability, recalling the concept of a flying capacitor configuration. The amplitude of the LDN voltage ripple is analytically determined considering both the low-order and the switching harmonic components. In particular, peak-to-peak distributions of voltage ripples over the fundamental period are analytically determined, making possible the design of dc-link capacitor relying only on the dc-voltage ripple requirements. The case study makes reference to negligible switching ripple in the output current. It well represents either grid connection or passive load having almost sinusoidal currents. Numerical simulations carried out by MATLAB/Simulink and a complete set of experimental verifications are given to confirm the theoretical developments. [ABSTRACT FROM AUTHOR]

This paper presents a model predictive control technique applied to a dual-active bridge inverter where one of the bridges is floating. The proposed floating bridge topology eliminates the need for isolation transformer in a dual inverter system and therefore reduces the size, weight, and losses in the system. To achieve multilevel output voltage waveforms, the floating inverter dc-link capacitor is charged to the half of the main dc-link voltage. A finite-set model predictive control technique is used to control the load current of the converter as well as the floating capacitor voltage. Model predictive control does not require any switching sequence design or complex switching time calculations as used for space vector modulation; thus, the technique has some advantages in this application. A detailed analysis of the converter as well as the predictive control strategy is given in this paper. Simulation and experimental results to validate the approach are also presented. [ABSTRACT FROM PUBLISHER]

This paper presents a new reconfiguration module for asymmetrical multilevel inverters in which the capacitors are used as the dc links to create the levels for staircase waveforms. This configuration of the multilevel converter makes a reduction in dc sources. On the other hand, it is possible to generate 13 levels with lower dc sources. The proposed module of the multilevel inverter generates 13 levels with two unequal dc sources (2VDC and 1VDC). It also involves two chargeable capacitors and 14 semiconductor switches. The capacitors are self-charging without any extra circuit. The lower number of components makes it desirable to be used in wide range of applications. The module is schematized as two back-to-back T-type inverters and some other switches around it. Also, it can be connected as a cascade modular which leads to a modular topology with more voltage levels at higher voltages. The proposed module makes the inherent creation of the negative voltage levels without any additional circuit (such as H-bridge circuit). Nearest level control switching modulation scheme is applied to achieve high-quality sinusoidal output voltage. Simulations are executed in MATLAB/Simulink and a prototype is implemented in the power electronics laboratory in which the simulation and experimental results show a good performance. [ABSTRACT FROM AUTHOR]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents an optimized topology of 3-$\phi$ , multilevel inverter (MLI) configuration for five or higher level operation with reduced switch count. The proposed solution consists of two basic units (BUs) of multilevel converter and a T-structured 3-level inverter (3-LI). Both BUs are equally shared by the three phases maintaining symmetry among the phases. Moreover, for a higher level operation of the proposed MLI, the modifications required are at two BUs only and not at three legs of the inverter. It further helps in reducing the requirement of extra components for higher level operation compared to the conventional solutions. Furthermore, the topology also has the benefits of reduced switching and conduction loss. An algorithm is also devised to generate the switching pulses for the BUs and the 3-LI, using a carrier-based space vector modulation technique. Presented topology is compared with other existing topologies to prove its advantage. All the details regarding the operating modes and pulse width modulation techniques employed for the proposed system are given and supported by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

Adding the auxiliary switches to the conventional H-bridge inverter is an effective way to eliminate the leakage current for transformerless PV systems, such as H5, H6, etc. Inspired by the newly developed embedded-switch H6 topology, a novel embedded-switch inverter (ESI) is proposed in this paper for three-phase transformerless PV systems. First, the operation principle and characteristics of the proposed ESI are analyzed. Second, the common-mode model of the three-phase ESI is established, based on which the main factors that affect the leakage current are discussed. The finding reveals that the switching states with conventional modulation strategy result in high-frequency common-mode voltage, which is the source of leakage current. In order to solve the problem, a new modulation strategy is presented for ESI to eliminate the high-frequency leakage current. Finally, the time-domain simulation and the experimental tests are carried out. The results verify the effectiveness of the proposed solution. [ABSTRACT FROM AUTHOR]

The battery energy-stored quasi-Z-source (BES-qZS)-based photovoltaic (PV) power generation system combines advantages of the qZS inverter and the battery energy storage system. However, the second-harmonic ( \text2\omega ) power ripple degrades the system's performance and affects the system's design. An accurate model to analyze the \text2\omega ripple is very important. The existing models did not consider the battery, or assumed a symmetric qZS network with $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$, which limits the design freedom and causes oversized impedance parameters. This paper proposes a comprehensive model for the single-phase BES-qZS-PV inverter system, where the battery is considered and there is no restriction of $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$ . Based on the built model, a BES-qZS impedance design method is proposed to mitigate the \text2\omega ripple with asymmetric qZS network. Simulation and experimental results verify the proposed \text2\omega ripple model and impedance design method. [ABSTRACT FROM AUTHOR]

The Z-source inverter (ZSI) employs an LC impedance network between the main inverter bridge and the power source. The unique feature of the ZSI is that it can operate either in buck or boost mode with a wide range of obtainable output voltages from a given input voltage. This topology also exhibits better electromagnetic-interference noise immunity when compared to a traditional voltage-source inverter (VSI). However, the LC impedance network of ZSI significantly increases the size and cost of the power converter and can make it unsuitable for low-power applications. This paper proposes a novel topology called switched boost inverter (SBI) which exhibits similar advantages of ZSI with lower number of passive components and more active components compared to ZSI. The steady-state and small-signal analyses of SBI, along with its pulsewidth modulation (PWM) control strategies, have been discussed in this paper. This paper also presents a comparison of SBI and ZSI with the same input and output parameters. The theoretical analysis given in this paper has been validated using a laboratory prototype of SBI, and the experimental results are presented for verification. The experimental harmonic spectrum of the inverter's output voltage with the proposed PWM technique is also plotted and compared with that of a traditional VSI. All the experimental results show good correlation between theory and experiments. [ABSTRACT FROM PUBLISHER]

In this paper, an immune algorithm (IA) is developed for optimization of the harmonic performance of a three-phase inverter under the space-vector pulsewidth-modulation (SVPWM) control strategy. The presented algorithm employs the immune approach as the search method for finding the best optimal control vectors and action time of the three-phase inverter. As a result, the optimal control vectors and action time are calculated to minimize the objective function of the weighted total harmonic distortion of the output voltage waveforms. In addition, an experimental platform based on DSP and field-programmable gate array is built. This paper provides a detailed performance analysis of the method with comparison to the conventional SVPWM. The simulation and experimental results verify the superiority of the best control sequences generated by IA compared with the existing conventional control strategies. [ABSTRACT FROM PUBLISHER]

A new pulse width modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is developed and presented in this paper. The proposed PWM scheme not only takes advantage of the special properties available in NPC inverters, but also reduces the switching loss of the inverter along with an inherent neutral point (NP) voltage control. Based on a circuit-level decoupling concept, the NPC inverter can be decoupled into two three-level Buck converters in every defined operating section, and thereby the controller design can be simplified. The salient features of the proposed scheme, as compared with the existing carrier-based DPWM strategies, are: 1) its reduced computational processing time, 2) its capability to balance the dc-link voltage without any additional control, and 3) its reduced complexity, e.g., only one carrier wave needed for pulse width modulating. Same as a space-vector modulation, the maximum modulation index, 1.1547, can be attainable by the proposed scheme. Moreover, compared to conventional continuous sinusoidal PWM, using this technique proposed here, the switching losses of the devices can be reduced by one third. In order to explain the operation of this topology properly, the decoupling principle including the driving signal synthesis and the NP potential variation are analyzed in detail in this paper. Finally, the viability and performance of the proposed modulation scheme are shown through simulation and experimental results in a laboratory prototype. [ABSTRACT FROM PUBLISHER]

This paper discusses the implementation of level-shifted and phase-shifted carrier-based modulation methods, in conjunction with a multiphase open-end winding drive topology. The considered drive is supplied using two five-phase two-level voltage source inverters (VSIs), with input provided from two isolated supplies of equal dc voltages. The topology is known to yield the same space-vector pattern as a corresponding three-level inverter in single-sided supply mode. It is shown in this paper that, with the application of a simple logic, the same phase voltage waveforms result as those obtainable with the appropriate carrier-based modulation scheme applied to the three-level VSI in single-sided supply mode. While the outcomes of the modulation techniques are the same, the open-end winding topology offers certain advantages, such as modularity and absence of capacitor voltage balancing requirements. The analysis is conducted for selected modulation methods using voltage and current waveforms, spectra Fast Fourier Transform (FFT), and total harmonic distortion as figures of merit. Theoretical considerations are verified by means of simulation and experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, a new cascade switch-ladder multilevel inverter topology is presented which can generate a large number of output voltage levels. First, a fundamental switch-ladder multilevel inverter structure is described. Then, the structure of recommended cascade topology based on series connection of fundamental switch-ladder topologies is presented. To generate maximum number of levels with minimum number of switching elements, dc sources, and voltage on switches, the proposed cascade topology is optimized. Comparison results prove that the presented cascade topology requires fewer numbers of components. Also, the value of voltage rating on switches is less than other structures. Experimental results for two topologies are analyzed to verify the performance of the proposed topology. [ABSTRACT FROM PUBLISHER]

This paper proposes a unique carrier-based pulse width modulation strategy for a three-level neutral-point-clamped inverter that works satisfactorily and with uniform convergence time over the full power factor (PF) range of the load variation. It has excellent control over capacitor voltages and mitigates low-frequency oscillations in the neutral point for the full PF range. First, an investigation is made to see how the load currents get modulated to generate compensating neutral current causing charging and discharging of dc-link capacitors. It is observed that when an additional modulating voltage signal that is in phase with the corresponding phase current is added in each phase, a neutral current is produced in the right direction which can be used to compensate for any prior unbalance in capacitor voltages. It is demonstrated that the performance of this scheme is insensitive to the load PF variation (full range from zero to unity). It performs satisfactorily throughout the entire linear modulation range and eliminates any undesirable low-frequency harmonic component in the compensating neutral current. The effectiveness of the proposed scheme is verified through simulation and experimental results by varying load PF as well as modulation index with both passive and motor loads. [ABSTRACT FROM PUBLISHER]

This paper presents a new family of hybrid Z-source boost dc–dc converters intended for photovoltaic applications, where the high step-up dc–dc converters are demanded to boost the low-source voltages to a predefined grid voltage. Because the boost capabilities of the traditional Z-source networks are limited, the proposed converters are composed of combine traditional Z-source networks in different ways to enhance the boost abilities of the traditional Z-source networks. The new version of the proposed Z-source converters is termed as hybrid Z-source boost dc–dc converters to satisfy the traditional benefits of Z-source networks with stronger voltage boost abilities which can also be applied to dc–ac, ac–ac, and ac–dc power conversions. The performances of the proposed converters are compared with other Z-source networks behaviors. The simulation and experimental results of the proposed converters are validated at different operating conditions. [ABSTRACT FROM PUBLISHER]

In this paper, a novel topology of six-level inverters for a medium-voltage high-power applications is proposed, which consists of inner flying-capacitor inverter (FCI) units and outer two-level inverter units. The proposed topology can reduce the number of devices, components, and isolated sources compared with the existing ones in the case of the same number of output voltage steps, which result in a reduction of the size and weight of the inverters. Also, the total power loss of the proposed topology is lower than that of the diode-clamped inverter (DCI) and FCI. Besides, the estimated cost of the proposed topology is about 60.5% and 81.3% compared with the DCI and FCI, respectively. In addition, the modulation technique and the control strategy for the dc-link capacitor and flying-capacitor voltages are developed for the proposed topology. The effectiveness of the proposed six-level inverter for the medium-voltage applications has been verified by simulation results. Also, the feasibility of the proposed inverter has been proved by experimental results for the prototype at the laboratory. [ABSTRACT FROM AUTHOR]

This paper proposes a new space-vector pulsewidth modulation (SV-PWM) strategy for a three-level neutral point clamped inverter. The presented SV-PWM strategy makes it possible to control the neutral point voltage by optimum choice of switch sequence for any position and length of output voltage vector. The proposed solution takes into consideration the unbalance of the dc-link voltages. It also analyzes the influence of vector sequences on the predicted unbalance of the dc-link voltage. The solution allows selecting optimum vectors and their on-time durations in order to reduce quickly the dc-link voltage unbalance. The calculation of the space vector area proposed in this paper takes into consideration voltage unbalance and its influence on the length and position of vectors. The proposed approach assures properly generating the voltage output vectors, even in the case of the existing large voltage unbalance in the dc-link. The results of the experimental investigation of the proposed modulation strategy are presented in this paper. [ABSTRACT FROM PUBLISHER]

In this paper, a model-predictive control (MPC) has been designed and implemented on the packed U-cell (PUC) inverter, which has one isolated dc source and one capacitor as an auxiliary dc link. The MPC is designed to regulate the capacitor voltage at the desired magnitude to have seven voltage levels at the output of the inverter. Since grid-connected application is targeted by this application, the inverter should be capable of supplying requested amount of active and reactive power at the point of common coupling (PCC) as well. Therefore, MPC should also consider the line-current control to monitor the exchange of reactive power with the grid while injecting appropriate active power at low total harmonic distortion (THD). Various experimental tests including change in dc-source voltage, active power variation, and operation at different power factor (PF) have been performed on a laboratory prototype to validate the good performance obtained by the proposed MPC. The dynamic performance of the controller during sudden changes in dc capacitor voltage, supply current, and PF demonstrates the fast and accurate response and the superior operation of the proposed controller. [ABSTRACT FROM PUBLISHER]

In this paper, a new topology for half-bridge switched boost inverter (HB-SBI) is proposed. The proposed half-bridge inverter uses more active elements rather than capacitors and inductors in comparison with the conventional half-bridge Z-source inverter with two Z-networks, which results in reduction of weight, size, and cost. Moreover, the proposed inverter has the capability of eliminating inverter leg short-circuit issues and is able to further increase the output voltage level in comparison with its conventional types. Generating zero-level output voltage is also another advantage of this topology. Based on theoretical calculations, the steady-state and small-signal analysis of the proposed topology in different operating modes are performed and the ripple of inductors’ current and capacitors’ voltage are also calculated. A comprehensive comparison is also made between the proposed inverter and the conventional types. Finally, the experimental results are provided to reconfirm the performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

The flying capacitor multilevel inverter (FCMLI) is one of the well-known structures of multilevel inverters having attracted considerable attention because of its merits. In spite of its many advantages, it has some limitations such as high volume and complicated control method because of its bulky capacitors and their voltage balancing requirement. Moreover, the high number of power semiconductors required makes this structure susceptible to failure. To increase the ratio of the number of levels to the number of components, an uneven distribution of capacitor voltages has been suggested in previous reports; however, this approach complicates the control method. Up to now, almost all presented methods suffer from high computational load and/or structure-dependent algorithm. In this paper, a simple state-based and structure-independent method is proposed for capacitor voltage regulation. The proposed method is straightforward and can perform online computation of switching sequences in a computationally efficient manner without any need for stored information or look-up tables. The method is conveniently extendible to any number of cells and levels in an FCMLI structure with arbitrary dc link voltage distribution schemes. Simulation and experimental results show the effectiveness and simplicity of this method. [ABSTRACT FROM PUBLISHER]

In this paper, a common grounded Z-source dc–dc converter with high voltage gain is proposed for photovoltaic (PV) applications, which require a relatively high output–input voltage conversion ratio. Compared with the traditional Z-source dc–dc converter, the proposed converter, which employs a conventional Z-source network, can obtain higher voltage gain and provide the common ground for the input and output without any additional components, which results in low cost and small size. Moreover, the proposed converter features low voltage stresses of the switch and diodes. Therefore, the efficiency and reliability of the proposed converter can be improved. The operating principle, parameters design, and comparison with other converters are analyzed. Simulation and experimental results are given to verify the aforementioned characteristics and theoretical analysis of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, a new inverter topology is proposed for generating a multilevel dodecagonal voltage space vector structure for open-end winding induction motor (IM) using a single dc source. Dodecagonal voltage space vector structure eliminates fifth- and seventh-order harmonic voltages from phase voltage output and hence eliminates the fifth- and seventh-order harmonic currents through the motor leading to removal of the dominant sixth-order torque ripple generation in the motor over the entire modulation range. Multilevel space vector structure generates output voltage with better THD and low dv/dt. In the proposed topology, two three-level inverters drive an open-end winding IM, one inverter from each side. DC-link of primary inverter is from a dc source which delivers the entire active power, whereas the secondary inverter dc-link is maintained by a capacitor, which is self balanced during the inverter operation. The PWM scheme implemented ensures low switching frequency for primary inverter. Secondary inverter operates at a small dc-link voltage. Hence, switching losses are small for both primary and secondary inverters. Experimental results show the elimination of fifth- and seventh-order harmonic voltages over the entire modulation range, validating effectiveness of the proposed multilevel inverter scheme. [ABSTRACT FROM PUBLISHER]

A four-level open-end winding induction motor (OEWIM) drive is known to suffer from two perennial problems. One is the problem of zero-sequence currentin the motor phases, which is caused by the existence of zero-sequence voltage in them. The other is the overcharging of the dc-link capacitor of theinverter operated with lower dc-link voltage by its counterpart operated with a higher dc-link voltage. This paper investigates the applicability of aspecial variant of space vector pulse width modulation (SVPWM) scheme for a recently proposed power circuit configuration, in which arectifier–inverter combination is nested within the conventional two-level inverter configuration to achieve four-level inversion. This PWM schemeis named as the sample-averaged zero-sequence elimination (SAZE) SVPWM scheme, wherein the zero sequence voltage is suppressed in each sampling timeperiod in the average sense. Both of the aforementioned problems encountered in this drive are successfully overcome for this power circuit configurationby resorting to the proposed SVPWM strategy. [ABSTRACT FROM PUBLISHER]

This paper proposes a new topology for an enhanced-boost Z-source inverter (ZSI) with combined two Z-impedance networks. By two Z-impedance networks and low shoot-through duty cycle, the proposed inverter produces high output voltage gain. In traditional ZSIs for high boosting voltage, a low modulation index is required; hence, under these conditions, the output voltage will have low quality with high total harmonic distortion. Compared with the conventional high-boost ZSI topologies, the proposed inverter uses shorter shoot-through duration and a larger modulation index to improve the output waveform quality. Comparison between the proposed topology and previously proposed schemes, in terms of inductor numbers, voltage and current stresses on elements, sizes of inductors and capacitors, efficiency, and switching device product (SDP) factors of diodes, is made, and the results verify the priority of the proposed topology. The operating principle of the proposed topology is analyzed in detail. Both simulation and experimental results verify the high performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

In this paper, a multilevel dodecagonal voltage space vector structure with nineteen concentric dodecagons is proposed for the first time. This space vector structure is achieved by cascading two sets of asymmetric three-level inverters with isolated H-bridges on either side of an open-end winding induction motor. The dodecagonal structure is made possible by proper selection of dc link voltages and switching states of the inverters. The proposed scheme retains all the advantages of multilevel topologies as well as the advantages of dodecagonal voltage space vector structure. In addition to that, a generic and simple method for calculation of pulsewidth modulation timings using only sampled reference values ( $v_\alpha$ and $v_\beta$) is proposed. This enables the scheme to be used for any closed-loop application such as vector control. In addition, a new method of switching technique is proposed, which ensures minimum switching while eliminating the fifth- and seventh-order harmonics and suppressing the eleventh and thirteenth harmonics, eliminating the need for bulky filters. The motor phase voltage is a 24-stepped waveform for the entire modulation range thereby reducing the number of switchings of the individual inverter modules. Experimental results for steady-state operation, transient operation, including start-up have been presented and the results of fast Fourier transform analysis is also presented for validating the proposed concept. [ABSTRACT FROM PUBLISHER]

In this paper, selective harmonic mitigation (SHM) and selective harmonic elimination (SHE) modulation techniques have been combined to produce appropriate pulses for a four-leg three-level neutral point clamped (NPC) inverter. In the proposed hybrid method, the SHM technique is applied to phase legs in order to mitigate non-triplen harmonics (fifth, seventh, $\ldots$) , and the fourth leg is controlled by the SHE principle to eliminate important low-order triplen harmonics (third, ninth, $\ldots$) completely. In this context, it is demonstrated that using SHM instead of an SHE modulator for phase legs leads to a reduced vast range of harmonic orders in the NPC output voltage, significantly. Moreover, it is proved that the presented hybrid switching technique has the ability of dc-bus capacitor voltage balancing, inherently. Furthermore, analyses are performed to calculate the dc-bus capacitances accurately to show 5% voltage ripple acceptably. Simulation and experimental results validate a good dynamic performance of the proposed hybrid modulation technique in firing the NPC inverter switches to generate low-harmonic voltage waveforms supplying balanced and unbalanced loads while balancing the dc capacitor voltages in a four-wire network with small dc-link capacitors. [ABSTRACT FROM PUBLISHER]

The objective of this paper is to propose a new inverter topology for a multilevel voltage output. This topology is designed based on a switched capacitor (SC) technique, and the number of output levels is determined by the number of SC cells. Only one dc voltage source is needed, and the problem of capacitor voltage balancing is avoided as well. This structure is not only very simple and easy to be extended to a higher level, but also its gate driver circuits are simplified because the number of active switches is reduced. The operational principle of this inverter and the targeted modulation strategies are presented, and power losses are investigated. Finally, the performance of the proposed multilevel inverter is evaluated with the experimental results of an 11-level prototype inverter. [ABSTRACT FROM PUBLISHER]

In this paper, a predictive control scheme is proposed for the low-voltage ride-through (LVRT) enhancement of direct-driven permanent-magnet-synchronous-generator-based megawatt-level wind turbines. The proposed method uses the turbine–generator rotor inertia to store the surplus energy during the grid voltage dips. The power conversion system is realized using a three-phase diode-bridge rectifier, a three-level-boost converter, and a neutral-point-clamped (NPC) inverter. The wind turbine requirements, such as maximum power point tracking, net dc-bus voltage control, balancing of the dc capacitor voltages, and reactive power generation, are modeled as the reference control variables. The generator- and grid-side cost functions are defined to deal with these control objectives. During each sampling interval, the control goals are achieved based on the minimization of cost functions. The coordination of boost and NPC converters and the exchange of reference control variables during normal and LVRT operation are formulated such that the power converters operate in a safe mode while meeting the grid code requirements. Simulation and experimental results are presented to validate the proposed strategy. [ABSTRACT FROM PUBLISHER]

This paper presents a novel direct current-fed interleaved phase-modulated single-phase unfolding inverter for fuel-cell applications. Two active-clamped zero-voltage switching current-fed half-bridge isolated converters are interleaved in parallel input and series output configuration. Phase modulation is proposed to control these two converter cells, which generate a rectified sinusoidal pattern at the dc link. A simple H-bridge unfolding dc–ac inversion is used to produce single-phase sine voltage at line frequency switching using square-wave control. This not only simplifies the inversion stage in terms of modulation but also reduces the switching losses. Direct front-end current-fed based unfolding inverter is not reported in literature yet. Detailed analysis and design of the proposed direct current-fed single-phase unfolding inverter has been presented. Simulation waveforms using PSIM 9.0.4 are given to verify the presented analysis and design. Experimental results on a laboratory prototype rated at 200 W are demonstrated to support the investigation, to validate the accuracy of the proposed analysis and design, and to test the performance. [ABSTRACT FROM PUBLISHER]

The five-level active neutral-point (NP)-clamped (ANPC) converter is a newly emerging topology which can overcome the drawbacks of traditional NP-clamped and flying-capacitor multilevel converters. This paper presents a comprehensive theoretical analysis of the NP potential balancing issue and demonstrates that the NP potential can be naturally balanced under ideal and steady conditions. An NP potential balancing method based on zero-sequence voltage injection is presented. By calculating the average NP currents of all key zero-sequence voltages, the most appropriate zero-sequence voltage is selected to generate the demanded NP current, which can also limit the switching frequency of the series-connected insulated-gate bipolar transistors to the fundamental frequency. A three-phase five-level ANPC inverter prototype is built up, and both steady and dynamic experimental results are presented to verify the validity of this method. [ABSTRACT FROM PUBLISHER]

In this paper, two reduced switch count topologies are introduced for independently supplying two single-phase ac loads with one inverter. Using a new three-switch leg structure recently introduced and implemented in three-phase converters, two types of dual-leg and single-leg topologies are developed which respectively are functionally comparable to two full-bridge and half-bridge inverters working independently though with a less number of semiconductor switches and hence control and gate drive circuit components. The proposed six-switch and three-switch topologies are introduced; two modes of equal frequency and different frequency operation each of its own distinctive characteristics are considered for them and their pulse width modulation schemes are elaborated. Comprehensive analyses of power loss profile and output waveform properties are conducted via simulation for the proposed inverters, and the results are compared with full-bridge and half-bridge inverters. To assess the performance of the proposed inverter topologies, working prototypes are built, and the experimental results are provided. [ABSTRACT FROM PUBLISHER]

Multilevel inverters have been widely accepted for high-power high-voltage applications. Their performance is highly superior to that of conventional two-level inverters due to reduced harmonic distortion, lower electromagnetic interference, and higher dc link voltages. However, it has some disadvantages such as increased number of components, complex pulsewidth modulation control method, and voltage-balancing problem. In this paper, a new topology with a reversing-voltage component is proposed to improve the multilevel performance by compensating the disadvantages mentioned. This topology requires fewer components compared to existing inverters (particularly in higher levels) and requires fewer carrier signals and gate drives. Therefore, the overall cost and complexity are greatly reduced particularly for higher output voltage levels. Finally, a prototype of the seven-level proposed topology is built and tested to show the performance of the inverter by experimental results. [ABSTRACT FROM PUBLISHER]

This paper is devoted to the step-up dc/dc converter family with a cascaded quasi-Z-source network (qZS-network). The cascaded (two-stage) qZS-network could be derived by the adding of one diode, one inductor, and two capacitors to the traditional quasi-Z-source inverter (qZSI). The proposed cascaded qZSI inherits all the advantages of the traditional solution (voltage boost and buck functions in a single stage, continuous input current, and improved reliability). Moreover, as compared to the conventional qZSI, the proposed solution reduces the shoot-through duty cycle by over 30% at the same voltage boost factor. Theoretical analysis of the two-stage qZSI in the shoot-through and non-shoot-through operating modes is described. The proposed and traditional qZS-networks are compared. A prototype of a step-up dc/dc converter with the cascaded qZS-network was built to verify the theoretical assumptions. The experimental results are presented and analyzed. Finally, a further optimization method of the cascaded qZS-network is proposed, and some practical design issues are discussed. [ABSTRACT FROM PUBLISHER]

In this paper, two space-vector-based pulsewidth modulation (PWM) (SVPWM) strategies named equal- and proportional-duty SVPWMs are described, which are used to synthesize a four-level waveform from an open-end winding configuration of an induction motor. Two isolated dc-link voltages, which are in the ratio of 2 : 1, are employed to achieve this objective. Both of these PWM strategies achieve the avoidance of overcharging of the dc-link capacitor of an inverter operating with lower dc-link voltage by its counterpart with higher dc-link voltage. Implementation of these PWM strategies requires only the instantaneous three-phase reference voltages, eliminating the need of sector identification or lookup tables. The numbers of samples per cycle for individual inverters are selected in such a way that the quarter-wave, half-wave, and three-phase symmetries are achieved for the dual-inverter drive despite unequal dc-link voltages for the constituent inverters. It is also shown that one of the two PWM techniques, called the proportional-duty SVPWM, results in a better spectral performance and lower switching power loss in the overall dual-inverter system compared to the equal-duty SVPWM. [ABSTRACT FROM PUBLISHER]

With regard to a five-level inverter comprising flying-capacitor asymmetric H-bridge, the impact on the capacitor voltage under conventional modulation approach is analyzed. Since it is sensitive to the fundamental period and the load current, it may introduce undesired low-order harmonics into the output voltage and may even break down the power switches due to the considerable fluctuation of the flying-capacitor voltage. Thus, this paper proposes a novel pulsewidth-modulation scheme with the positive and negative cross carriers, which controls the flying-capacitor voltage by utilizing the redundant switching states of the output voltages. Three modes of precharging the flying capacitor without extra equipments are presented. Moreover, the capacitance of the flying capacitor and the switching frequency of the power switches can be chosen according to the allowable fluctuation of the flying-capacitor voltage and the load current. In order to remove the overlapping of the level layers, the optimization of the line-to-line voltage waveform is proposed to synthesize the reference vector with the “nearest three-vector” approach. The theory is supported by the experimental results from the prototype. [ABSTRACT FROM AUTHOR]

This paper proposes an energy regeneration circuit for three-phase voltage-fed inverters using a modified Undeland snubber. The proposed system uses a quasi-square-wave zero voltage switching dc–dc auxiliary converter to regenerate the energy from snubber capacitor to the dc bus. The regenerative circuit uses a single active switch, and it operates independently of the three-phase inverter. Operation stages, theoretical waveforms, and a design methodology are presented. Experimental results based on a 4.5-kVA three-phase inverter prototype are included to validate the proposed topology. [ABSTRACT FROM PUBLISHER]

Unipolar sinusoidal pulsewidth modulation (SPWM) full-bridge inverter brings high-frequency common-mode voltage, which restricts its application in transformerless photovoltaic grid-connected inverters. In order to solve this problem, an optimized full-bridge structure with two additional switches and a capacitor divider is proposed in this paper, which guarantees that a freewheeling path is clamped to half input voltage in the freewheeling period. Sequentially, the high-frequency common-mode voltage has been avoided in the unipolar SPWM full-bridge inverter, and the output current flows through only three switches in the power processing period. In addition, a clamping branch makes the voltage stress of the added switches be equal to half input voltage. The operation and clamping modes are analyzed, and the total losses of power device of several existing topologies and proposed topology are fairly calculated. Finally, the common-mode performance of these topologies is compared by a universal prototype inverter rated at 1 kW. [ABSTRACT FROM AUTHOR]