Search

The development of a high static gain dc–dc converter with the integration of the voltage multiplier cell and the coupled inductors operating with soft switching is presented in this paper. The use of coupled inductors and voltage multiplier techniques allow the operation with low switch voltage and low conduction losses. The switch turn-on commutation occurs with zero current switching due to the presence of the coupled-inductor leakage inductance. The leakage inductance also reduces the reverse recovery current of all diodes. The zero voltage switching at the power switch turn-off is obtained with the inclusion of only a diode and a snubber capacitor per phase, without the use of auxiliary switches. The soft-switching range is independent of the load and is maintained even with a light load. The theoretical analysis, design procedure, and experimental results are presented in this paper. A two-phase boost converter with one voltage multiplier and coupling inductors was built with an input voltage $V_{{\text{in}}}= { \text{24 V}}, output voltage Vo= { \text{432 V}}, and output power Po= { \text{400 W}}. The efficiency obtained is equal to 94.55% at the nominal power. [ABSTRACT FROM PUBLISHER]

This paper introduces the bridgeless triple-mode resonant ac–dc converter and presents its dynamic model and control technique. The proposed converter operates in triple mode: discontinuous-conduction mode (DCM), continuous-conduction mode (CCM), and missing resonance mode (MRM). It has the advantages of small number of required components, medium power capacity, and high efficiency, but it is difficult to control because DCM, CCM, and MRM have their own dynamic characteristics. To solve this control problem, the mode boundaries are first identified and, corresponding to each mode, the dynamic model is developed to design the controller. In each mode, we propose to add a repetitive controller (RC) with a phase-lead compensator to the conventional duty ratio plus feedback controller. The RC is used to suppress the deterministic periodic disturbances and the phase-lead compensator is used to compensate for the incurred phase lag. A 1-kW digitally controlled converter prototype is built and used to demonstrate the validity of the proposed modeling and control approach. [ABSTRACT FROM AUTHOR]

The interleaved bidirectional buck–boost converter dual active half-bridge (IBBC-DAHB) dc–dc converter consists of two converters IBBC and DAHB and a coupled inductor. The IBBC-DAHB converter has significant features such as low ripple current at the low-voltage side, low current stress on the input inductors, voltage stress across the switches less than the high-voltage side, high voltage gain, and zero-voltage soft switching. The converter offers high efficiency using phase-shift modulation when it operates at a nominal design operating point. However, the efficiency decreases due to high circulating current, high current stress, and limited soft-switching range when the source and load voltages deviate from their nominal values. This paper employs both duty cycle and phase-shift modulation methods to improve the above mentioned shortcomings using voltage matching for the DAHB converter. The proposed converter is analyzed and a 500-W experimental prototype with 40–60 V input voltage and 400 V output voltage under 100 kHz switching frequency is implemented to verify the theoretical results. The maximum efficiency of 97.15% is achieved at 60 V and 400 W. A flat efficiency characteristic for the converter is derived by the proposed control method, where the efficiency at 20% of nominal load is 91% and much higher than the phase-shift control, which is 70.8%. [ABSTRACT FROM AUTHOR]

Due to the pulsating power at the inverter output terminals, the passive storage elements of the boost stage of the current-fed switched inverter (CFSI) contain a power frequency harmonic component (100 Hz), apart from dc and switching frequency components. In prior designs, the second harmonic component is suppressed by increasing the size of the input filter inductor and capacitor or by using additional circuits. This paper presents a complete characterization of a control-based approach to suppress the power frequency harmonic component in the input inductor current of a CFSI. It also presents a comprehensive characterization of the harmonic power redistribution. Using the proposed approach, it is demonstrated that the inductor value of a CFSI is reduced by 61% for the same peak-to-peak ripple. This leads to an improvement in the conversion ratio, efficiency, and power density of the overall converter. A SiC MOSFET-based CFSI with 75-kHz switching frequency is used to verify the proposed design philosophy. [ABSTRACT FROM AUTHOR]

In this paper, a self-oscillating soft-switched converter for light-emitting-diode (LED) driver application is presented. In the proposed converter, the self-oscillation conditions are provided with a low number of additional components, and this converter provides a zero-current switching (ZCS) condition for instant switch turn-OFF. This converter does not need additional output current feedback because the output current changes only 10% when the output voltage changes by 33%. The self-oscillating part of this converter applies three low-power BJT and guarantees a soft-switching condition. The proposed self-oscillating control circuit can be implemented with a low cost since it does not need any IC and power supply for the control circuit. The proposed self-oscillating circuit detects the proper moment to turn the switch OFF under the ZCS condition. In order to justify the validity of theoretical analysis, the results of the implemented prototype for driving an LED string are presented. The measured power factor of the prototype shows that, although the input current of the converter is not sinusoidal, this converter can meet the IEC61000-3-2 standard at an operating power of less than 25 W, in addition to having a simple structure and achieving the robust ZCS condition. [ABSTRACT FROM PUBLISHER]

This paper proposes an interleaved buck converter (IBC) with continuous input current, extremely low output current ripple, low switching losses, and improved step-down conversion ratio. Unlike the conventional IBC, the proposed converter has a continuous input current, and its output current ripple is extremely low. The proposed converter has a lower voltage stress in comparison to the conventional IBC and can also provide a high step-down ratio, which makes it a proper choice for high-power applications where a nonisolated step-down converter with low output current ripple and continuous input current is required. Also, the proposed converter can provide current sharing between two interleaved modules without using additional current-sharing control method. All of these benefits are obtained without any additional stress on the circuit components. A prototype converter with 200-V input and 24-V–10-A output is implemented to verify the theoretical analysis. Operational principles and experimental results are presented in this paper. [ABSTRACT FROM PUBLISHER]

This paper proposes a bidirectional three-phase direct ac–ac converter, with only capacitors and switches in its power circuit and with its operation based on the switched-capacitor principle. The converter presents fixed gain, it keeps the frequencies of the output and input voltages equal, and it operates in open loop with constant switching frequency and duty cycle. The main advantages of the proposed converter are the absence of magnetic elements in the power circuit, the higher efficiency, the higher power density, the higher specific power, the lower cost, and the fact that it can convert ac–ac voltages within a wide frequency range, including dc voltage. Therefore, it is suitable to replace the conventional three-phase autotransformer in industrial, commercial, and residential applications, and it can be designated as a magnetic-less three-phase solid-state autotransformer. The principle of operation, a qualitative and quantitative analysis, the design methodology, and a fabricated example are described in this paper. In order to verify the converter in the laboratory, a prototype with the following characteristics was designed and fabricated: 6 kW, 1.35 kW/kg, 380/110 V, and switching frequency of 100 kHz. The measured efficiency at rated power was 96.3%, and other relevant experimental results are reported herein. [ABSTRACT FROM PUBLISHER]

Direct current voltages unbalance of respective power cells is an inherent and critical problem in a cascaded multilevel converter, which is widely used in the solid-state transformer. In this paper, an n -dimension space vector pulse width modulation is presented to address this issue in a three-level H-bridge-based cascaded multilevel converter. This algorithm utilizes the redundant switching pairs of the inner cell and the redundant vectors of mutual cells to balance capacitors’ and cells’ voltages. Meanwhile, a smooth vector transition strategy is included in this algorithm to avoid the level-skip phenomenon. The calculation processes are analyzed in one-cell, two-cells, and three-cells modes, respectively. It is simple, calculable, and flexible to extend in n-cells mode. Finally, the voltage balancing capacity of the inner cell and mutual cells with smooth level transition are verified by simulations and experiments not only at startup but also with unbalanced loads. [ABSTRACT FROM PUBLISHER]

The control loop stability in boost converters operating in continuous conduction mode has been restricted due to its nonminimum phase nature: the presence of a positive zero (right-half plane zero) in the control to output voltage transfer function. This paper proposes a method to mitigate the effect of the zero on the control loop by shifting the position of the zero to the left-half plane and hence leading to increased stability for the control loop of the boost converter. Superior performance of the proposed method has been clearly demonstrated using simulation and experimental results. [ABSTRACT FROM PUBLISHER]

A nonisolated single-stage electronic lighting system with a high power factor for driving power light-emitting diodes (LEDs) is proposed in this paper. The presented topology is based on the integration of a bridgeless boost rectifier with a nonresonant half-bridge converter. Accurate steady-state analyses of the nonresonant- and resonant-based circuits are reported, serving as the basis for designing the lighting systems. The LEDs current is adjusted by means of frequency modulation, being the converter switches driven by complementary symmetrical signals. A small-signal analysis is detailed for the proposed nonresonant scheme, providing fundamental information regarding its dynamic behavior. Also, a step-by-step design procedure based on the performed mathematical analysis is elaborated, allowing the adequate design of the proposed lighting system. In order to confirm the validity and the feasibility of the proposed converter, experimental results for a 42-W, 127- \rmV{\rm{rms}}, 50-kHz, 94.2% peak efficiency prototype are presented. [ABSTRACT FROM PUBLISHER]

In this paper, a new cascaded high step-up multilevel converter topology is designed, which is based on the series connection of several switched-capacitor submultilevel units. The voltage gain of proposed multilevel converter is related to the number of used switches-capacitor units. The main advantage of proposed topology is inherent voltage balancing of used capacitors. The proposed cascade topology is optimized to minimize the number of capacitors, power switches, and the value of voltage on switches for given levels. The proposed topology is compared with other high step-up multilevel converter topologies and conventional structures. The comparison results show that the presented structure requires the least number of switches and dc sources. Moreover, the voltage on the switches of proposed topology is low. In order to confirm the operation of proposed high step-up multilevel converter, both experimental and simulation works are provided. [ABSTRACT FROM PUBLISHER]

This paper proposes a phase-shift interleaving control method for variable-phase switched-capacitor (SC) converters that can perform voltage conversions with little electromagnetic interference over a wide range of operating condition. This is achieved by having multiple units of SC converter connected in parallel and an N-state hysteresis unit selection control scheme which works along the interleaving control to vary the number of converters in operation. By having the capacitors of inactive units connected to the output and the converters operating with output interleaving operation, the output capacitor that is typically required in SC converters for maintaining a small voltage ripple is made redundant in this configuration. A three-unit SC converter of the proposed configuration is described in this paper. Experimental results show that the proposed solution works satisfactorily with good regulation, input and output interleaving operations, and dynamic response for a wide operating range. [ABSTRACT FROM PUBLISHER]

Single-phase power factor correction (PFC) ac–dc converters are widely used in the industry for ac–dc power conversion from single phase ac-mains to an isolated output dc voltage. Typically, for high-power applications, such converters use an ac–dc boost input converter followed by a dc–dc full-bridge converter. A new ac–dc single-stage high-power universal PFC ac input full-bridge, pulse-width modulated converter is proposed in this paper. The converter can operate with an excellent input power factor, continuous input and output currents, and a non-excessive intermediate dc bus voltage and has reduced number of semiconductor devices thus presenting a cost-effective novel solution for such applications. In this paper, the operation of the proposed converter is explained, a steady-state analysis of its operation is performed, and the results of the analysis are used to develop a procedure for its design. The operation of the proposed converter is confirmed with results obtained from an experimental prototype. [ABSTRACT FROM PUBLISHER]

In this paper, a new isolated high step-up dc–dc converter is proposed based on the quasi-switched-boost network. The proposed converter has the following features: 1) continuous input current; 2) reduced turn ratio of the isolated transformer; 3) increased reliability, as it can operate in either short-circuit mode or open-circuit mode without causing damage to the power converter; and 4) unchanged primary and secondary voltage waveforms of the transformer, although the shoot-through duty cycle is variable. Compared to the quasi-Z-source-based isolated dc–dc converter, the proposed converter uses fewer passive components. The operating principles, analysis, parameter design guideline, and comparison with the quasi-Z-source-based isolated dc–dc converter are presented. A 450 W prototype is built to test the proposed converter. The proposed converter is applicable for distributed power generation applications where a varying low dc input voltage is converted to a high stabilized dc output voltage with a galvanic separation requirement. [ABSTRACT FROM AUTHOR]

In this paper, an improved model predictive control (MPC) of the modular multilevel converter (MMC) with reduced computational burden is proposed. A mathematical model of the MMC system based on the sum and difference of arm voltages are derived. Instead of determining the switching state of individual submodule (SM), the voltage levels of MMC are considered as control options based on the assumption that the SM capacitor voltages are well balanced. The further reduction of calculation effort is realized by using the tolerance band of capacitor voltages. The proposed MPC has a hierarchical structure. The cost function taking into account the ac-side current control, circulating current elimination and arm energy balancing is presented. The optimal voltage level, selected by the cost function, provides the voltage reference for the pulse width modulation modulator. The SM capacitor voltage balancing is done using a separate control loop. The proposed control strategy is investigated using an MMC high-voltage direct current system with 200 SMs in each arm in real-time simulation and hardware-in-the-loop tests. The performance of proposed method is verified by both steady-state and transient-state operations. [ABSTRACT FROM PUBLISHER]

This paper presents a high-efficiency multilevel flying-capacitor (FC) dc/dc power conversion with a lower passive component rating and power device count for distributed renewable energy systems. A resonant technique is adopted for the proposed dc/dc converter to achieve zero-current switching (ZCS) for all switches. Theoretical analysis is carried out for the proposed quintuple topology with three active switches. The proposed converter is evaluated to the conventional FC converter, in terms of the component rating and count, to highlight its advantages with respect to the power density and cost. The experimental results of a 1-kW prototype FC converter are presented to validate the theoretical analysis and principles, as well as attest the feasibility of the proposed topologies. [ABSTRACT FROM PUBLISHER]

A single-objective predictive control method that deals with four main control objectives applied to a multivariable single-phase three-level neutral-point-clamped converter operating as an active power filter is proposed in this paper. The four control objectives are to self-support the dc-bus voltage under load variations, to compensate the reactive power and the current harmonics, and to balance the dc capacitor voltages by using a predefined combination of the redundant switching states of the converter. The main contribution of the proposed method is that these objectives are accomplished without using weighting factors in the cost function, which eliminates problems such as multiobjective optimization or additional empirical procedures for determination of these factors. As a result, the method is easy to implement and rapidly selects the optimal voltage to improve the dynamic-state performance. Experimental results from a 2-kVA prototype are presented to prove that the method is valid for single-phase compensation. The well-known effect of model parameter errors' issue, which is inherent in predictive control methods, is also tested to confirm that the harmonic distortion in the grid current is below 5% even when the predictive model has a 25% error between actual and theoretically estimated grid impedance values. [ABSTRACT FROM PUBLISHER]

This paper presents a voltage-balancing method for stacked multicell converters (SMCs) based on phase disposition pulsewidth modulation. A cost function is evaluated to select the optimum state from a pool of redundant possible ones at each voltage level. It is demonstrated that, if sawtooth carriers are used for modulation instead of standard triangular ones, significant reduction in the switching frequency and the associated power losses of the power devices can be achieved without affecting the voltage-balancing capability. Experimental results from a seven-level SMC laboratory prototype are provided to verify the proposed voltage-balancing method against linear and nonlinear loads, as well as under transient conditions. [ABSTRACT FROM PUBLISHER]

The modular multilevel converter (MMC) becomes attractive for medium- or high-power applications because of the advantages of high modularity, availability, and power quality. One of the technical challenges associated with an MMC is the balancing of the capacitors' voltages. In this paper, a voltage-balancing control method is proposed for the MMC under phase-shifted carrier-based pulsewidth modulation. The proposed voltage-balancing method uses the linearization method for pulse sorting without arm current measurement, which can control the capacitor charge transfer to balance the capacitor voltage in the MMC. In the proposed method, the voltagebalancing algorithm is implemented in each carrier wave period, which reduces the computational intensity and burden. In addition, the arm current can also be improved with the proposed method. The simulation studies with the professional tool PSCAD/EMTDC are conducted, and a downscale MMC prototype is also tested with the proposed method. The study results show the effectiveness of the proposed voltage-balancing method. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel high-conversion-ratio high-efficiency isolated bidirectional dc–dc converter. The proposed converter is operated in the step-down stage. The dc-blocking capacitor in the high-voltage side is used to reduce the voltage on the transformer, and the current-doubler circuits are used in the low-voltage side to reduce the output current ripple. The energy stored in the leakage inductance is recycled to the dc-blocking capacitor. When the proposed converter is operated with a step-up function, dual current-fed circuits on the low-voltage side are used to reduce the current ripples and conduction losses of the switches in the low-voltage side. The voltage-doubler circuit in the high-voltage side increases the conversion ratio. The proposed converter can achieve high conversion with high efficiency. Experimental results based on a prototype implemented in the laboratory with a high voltage of 200 V, low voltage of 24 V, and output power of 200 W verify the performance of the proposed converter. The peak efficiency of the proposed converter in the high-step-down and high-step-up stages is 96.3% and 95.6%, respectively. [ABSTRACT FROM PUBLISHER]

This paper presents a power factor correction (PFC)-based bridgeless isolated Cuk converter-fed brushless dc (BLDC) motor drive. A variable dc link voltage of the voltage source inverter (VSI) feeding the BLDC motor is used for its speed control. This allows the operation of VSI in fundamental frequency switching to achieve an electronic commutation of the BLDC motor for reduced switching losses. A bridgeless configuration of an isolated Cuk converter is derived for the elimination of the front-end diode bridge rectifier to reduce conduction losses in it. The proposed PFC-based bridgeless isolated Cuk converter is designed to operate in discontinuous inductor current mode to achieve an inherent PFC at the ac mains. The proposed drive is controlled using a single voltage sensor to develop a cost-effective solution. The proposed drive is implemented to achieve a unity power factor at the ac mains for a wide range of speed control and supply voltages. An improved power quality is achieved at ac mains with power quality indices within the limits of the IEC 61000-3-2 standard. [ABSTRACT FROM PUBLISHER]

A hybrid switched-capacitor/interleaved boost converter able to provide a high voltage gain and to cancel the input current ripple at a preselected duty cycle was recently presented in the literature. This paper extends that work by proposing an optimized switching strategy for operating conditions at other values of duty cycle. The switching strategy effect on the converter's voltage gain and input current ripple is quantified and compared against the performance under the conventional switching strategy. The approach is validated in the laboratory through hardware prototyping. [ABSTRACT FROM PUBLISHER]

This paper analyzes the interleaved boost with coupled inductors (IBCI) converter, which is an isolated topology that is suitable for high step-up applications. Two main contributions are given: an exhaustive steady-state analysis and an accurate small-signal model. The former allows for deriving a closed-form noniterative design procedure for the power-stage active and passive components. In addition, it reveals an interesting equivalence with an apparently different converter, i.e., the single active bridge. Subsequently, the IBCI converter dynamic behavior is investigated, deriving a nonlinear average model that, under small-signal approximation, can be linearized around a given operating point and used for feedback controller design. A single photovoltaic module interface converter, rated for 300-W output power, is considered as a case study to validate the analysis outcome and the design procedure. Both are fully validated by measurements taken on the laboratory prototype. [ABSTRACT FROM PUBLISHER]

Recently, the interest in offshore wind farms has been significantly increased because of the stronger and more stable winds at sea, which will lead to a higher power production. DC/DC power conversion solutions are becoming more popular for fulfilling the growing challenges in the high-voltage (HV) dc-connected offshore wind power industry. This paper presents several multilevel modular dc/dc conversion systems based on the capacitor-clamped (CC) module concept for high-power offshore wind energy applications. Two types of the CC modules, namely, the double-switch (DS) module and the switchless (SL) module, are discussed. A soft-switching technique is adopted to achieve minimal switching losses and the maximum system efficiency. Theoretical analysis is carried out for the $2n+1$-level cascaded configurations based on the CC modules. The inherent interleaving property of the proposed configurations effectively reduces the output voltage ripple without adding extra components. A cascaded hybrid topology is developed by the combination of DS and SL modules. The proposed hybrid topology achieves higher efficiency and lower component count. The cascaded hybrid approach is evaluated in terms of the power device count, reliability, and efficiency against other HV dc/dc topologies to demonstrate its advantage for HVDC-connected offshore wind farms. The experimental results of two 5-kW prototype CC converters are presented to validate the theoretical analysis and principles as well as attest the feasibility of the proposed topologies. [ABSTRACT FROM PUBLISHER]

This paper presents a capacitor voltage balancing control applicable to any multilevel dc–ac converter formed by a single set of series-connected capacitors implementing the dc link and semiconductor devices, such as the diode-clamped topology. The control is defined for any number of dc-link voltage levels and converter legs (for single-phase and multiphase systems), guaranteeing the capacitor voltage control for any modulation index value and load (from idle mode to full power). The associated control loop small-signal transfer function is presented, from which optimum compensator design guidelines are derived. The improvement in control performance is verified through simulation and experiments comparing with a previous balancing control strategy in a four-level three-phase dc–ac conversion system. The satisfactory control performance is also verified through simulation in a four-level five-phase dc–ac conversion system. [ABSTRACT FROM PUBLISHER]

Automotive embedded electronic systems have been increasing in power and complexity and, therefore, more advanced power electronic converters are necessary in these vehicles. Several dual-voltage (42 V/14 V) bidirectional converter architectures have been proposed for automotive systems in recent years. However, most of them have low efficiency or are based in series and parallel configurations with large number of semiconductors and magnetics devices. Therefore, in this paper, we propose a bidirectional high-efficiency converter with lower number of components. This converter was created by merging a switched-capacitor converter and a conventional bidirectional converter, resulting in a hybrid topology. The voltage across the semiconductors of the proposed converter is equal to half of the highest voltage source value. Furthermore, the topology is composed of only one inductor to control the power flow between the two voltage sources. To verify all the mentioned features, a prototype was implemented experimentally, reaching a maximum efficiency of 97.5%. [ABSTRACT FROM PUBLISHER]

The modular multilevel converter (MMC) becomes attractive for high-voltage and high-power applications due to its high modularity, availability, and power quality. The voltage balance issue of capacitors is very important in the MMC, and balancing of the capacitor voltage is increasingly difficult as the switching frequency is reduced. In this paper, a voltage-balancing method is proposed for the MMC switched at grid frequency with reduced losses and does not rely on the arm current. By assigning the low-frequency pulses with different pulsewidths, the capacitor charge transfer in the MMC can be controlled for keeping the capacitor voltage balancing in the MMC. Simulations and experimental studies of the MMC are conducted, and the results confirm the effectiveness of the proposed capacitor voltage-balancing method. [ABSTRACT FROM PUBLISHER]

This paper presents a dc-to-dc converter, which offers continuous input and output energy flow and low input current ripple, applicable and mandatory for photovoltaic (PV) arrays and maximum power tracking applications. The PV array yields exponential curves for current and voltage where maximum power occurs at the curve's mutual knee. Conventional dc-to-dc converters have a relatively high input current ripple which causes high power losses when connected to nonlinear sources like PV arrays. The proposed converter maximizes the power that can be sourced from the PV array, without the need of any electrolytic filtering capacitance. The effect of current ripple can be significant and decreases PV system efficiency. Converter simulations and experimental results support and extol the system concept. [ABSTRACT FROM PUBLISHER]

In this paper, we review relevant problems in the modeling of dc–dc converters with switched capacitors. We study several approaches that overcome the exposed modeling difficulties, addressing ideal and nonideal cases and using dynamic equations that are valid in a large-signal domain. [ABSTRACT FROM PUBLISHER]

A single-switch nonisolated dc/dc converter for a stand-alone photovoltaic (PV)-battery-powered pump system is proposed in this paper. The converter is formed by combining a buck converter with a buck-boost converter. This integration also resulted in reduced repeated power processing, hence improving the conversion efficiency. With only a single transistor, the converter is able to perform three tasks simultaneously, namely, maximum-power-point tracking (MPPT), battery charging, and driving the pump at constant flow rate. To achieve these control objectives, the two inductors operate in different modes such that variable switching frequency control and duty cycle control can be used to manage MPPT and output voltage regulation, respectively. The battery in the converter provides a more steady dc-link voltage as compared to that of a conventional single-stage converter and hence mitigates the high voltage stress problem. Experimental results of a 14-W laboratory prototype converter with a maximum efficiency of 92% confirmed the performance of the proposed converter when used in a PV-battery pump system. [ABSTRACT FROM PUBLISHER]

Affected by the equivalent series resistance (ESR) of the devices in the circuit, the voltage-conversion ratio of traditional boost converter is limited. Various topologies have been developed to provide a high step-up voltage gain. An inherent high voltage gain can be achieved in a dual-switch converter with the advantages of low voltage and current stress on the switches. However, this converter has a strict requirement of the parameters' consistency. This paper discusses the steady-state operation principle of the converter in detail under the condition that the parameters are inconsistent and then illustrates the solutions to balance the voltage on the switches and suppress the resonance with passive lossless clamping. Finally, a prototype has been established in the laboratory, and simulation and experimental results have been given to verify the analysis and the effectiveness of clamping method. [ABSTRACT FROM PUBLISHER]

This paper presents a high-efficiency offline isolated LED driver based on a flyback converter. In order to achieve high power conversion efficiency as well as a low-cost design, a simple passive lossless turn-off snubber is proposed to reduce the switching loss of the power switch. A primary-side power regulation scheme is also proposed to compensate for forward voltage variation and aging caused by process and temperature variations. The proposed control scheme is designed and fabricated on-chip using a 0.35- \mu\m BCDMOS process. Test results of the proposed LED driver show an efficiency level that exceeds 83% (up to 90%) in an output range of 5–10 W with an input range of 85–265 VAC. [ABSTRACT FROM PUBLISHER]

This paper presents a boost converter with a proposed tapped inductor ripple cancellation network. Based on the conventional boost converter (CBC), a small capacitor and a small inductor are added as the ripple cancellation network (RCN) in the proposed converter. Meanwhile, the tapped inductor can be easily realized by adding an extra tap in the main inductor of the CBC. Since the capacitor and inductor in the RCN do not need to handle the main power as the conventional LC input filter, the size and weight of the proposed converter are relatively small comparing the CBC with the LC input filter. The small signal and dynamic characteristics analyses show that the proposed converter has the same static and dynamic responses as the CBC, and the input current ripple cancellation can be achieved in all power ranges without significantly increasing the losses. Finally, three 36–50-V, 500-W prototypes operating at 100 kHz are implemented to verify the expected performance. The simulation and experimental results show that the proposed converters can achieve input current ripple cancellation with efficiency higher than 97.4% in all power ranges. [ABSTRACT FROM PUBLISHER]

A method for extending the duty cycle range of series-input interleaved forward converter (SII-FC) is proposed in this paper. A family of novel SII-FC topologies is derived by integrating two switching legs, which belong to two forward cells, into one switching leg shared by both the two forward cells in the SII-FC. By employing the proposed method, the derived topologies have the advantages of extended duty cycle, reduced components, and conduction losses, which help to achieve high power density and high efficiency. These advantages make the SII-FC topologies suitable for such applications with wide input voltage range. A series-input interleaved two-switch forward converter (SII-TS-FC) is analyzed in detail, which is a typical SII-FC topology developed by the proposed method. It is composed of two low-voltage switching legs and a high-voltage switching leg. Detailed analysis indicates that the maximum duty cycle of the SII-TS-FC can reach 2/3, which is 1.33 times of that of the two-switch forward converter. The switches of the high-voltage leg can be soft-switched when duty cycle is less than 0.5, while the switches of the low-voltage legs can be soft-switched when duty cycle is larger than 0.5. As a result, high efficiency is achieved over a wide voltage range. In addition, the output filter can be reduced due to the interleaving operation of the two forward cells. The operational principles, characteristics, and design considerations for the proposed SII-FC are presented. Experimental results on the SII-TS-FC prototype with 200–400 V input 48 V/12 A output verify the proposed method and analysis. [ABSTRACT FROM PUBLISHER]

This paper presents the hybrid seven-level cascaded active neutral-point-clamped (ANPC)-based multilevel converter. The converter topology is the cascaded connection of a three-level ANPC converter and an H-bridge per phase. The voltage of the H-bridge is actively maintained to the required level through selection of the switching states of the converter. The topology is operated under selective harmonic elimination pulsewidth modulation (SHE-PWM), maintaining the switching frequency of the converter to a minimum. The operating principles, voltage balancing methods, and limitations of the converter are analyzed together with extensive simulation results of the topology. Experimental results from a low-power laboratory prototype are presented that verify the operation of the hybrid converter under SHE-PWM. [ABSTRACT FROM PUBLISHER]