Search

In this paper, a novel grid-connected high step-up inverter is proposed. The topology is composed of two stages. The first stage is a single-switch high step-up dc–dc converter with bipolar outputs, and the second stage is a conventional half-bridge dc–ac grid-connected inverter. Negative grounding of the photovoltaic (PV) module has resulted in elimination of unwanted ground leakage currents in the PV system. Simple structure, employing few semiconductor switches, simple control, and high efficiency are the features of the proposed topology. Theoretical analysis and principal operation of the circuit are discussed. An experimental prototype is implemented to verify the performance of the proposed inverter. The experimental results confirm the aforementioned features and the theoretical analysis of the converter operation. [ABSTRACT FROM PUBLISHER]

This paper proposes a new topology for an enhanced-boost Z-source inverter (ZSI) with combined two Z-impedance networks. By two Z-impedance networks and low shoot-through duty cycle, the proposed inverter produces high output voltage gain. In traditional ZSIs for high boosting voltage, a low modulation index is required; hence, under these conditions, the output voltage will have low quality with high total harmonic distortion. Compared with the conventional high-boost ZSI topologies, the proposed inverter uses shorter shoot-through duration and a larger modulation index to improve the output waveform quality. Comparison between the proposed topology and previously proposed schemes, in terms of inductor numbers, voltage and current stresses on elements, sizes of inductors and capacitors, efficiency, and switching device product (SDP) factors of diodes, is made, and the results verify the priority of the proposed topology. The operating principle of the proposed topology is analyzed in detail. Both simulation and experimental results verify the high performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

This paper focuses on the galvanically isolated quasi-Z-source dc–dc converter with a novel zero voltage and zero current switching technique. The unique feature of the impedance network lies in combining the buck–boost operation capability with the short- and open-circuit immunity of transistors; at the same time, it can perform zero voltage and zero current switching on the primary side. The boundary conduction mode of the current in the second inductor of the quasi-Z-source network was used along with snubber capacitors in the two out of four transistors and a special control algorithm to achieve full zero-switching operation of the inverter. Simulation and experimental results prove the discussed ideas. Possible modifications of the algorithm and future applications are also described. [ABSTRACT FROM PUBLISHER]

In this paper, a multilevel dodecagonal voltage space vector structure with nineteen concentric dodecagons is proposed for the first time. This space vector structure is achieved by cascading two sets of asymmetric three-level inverters with isolated H-bridges on either side of an open-end winding induction motor. The dodecagonal structure is made possible by proper selection of dc link voltages and switching states of the inverters. The proposed scheme retains all the advantages of multilevel topologies as well as the advantages of dodecagonal voltage space vector structure. In addition to that, a generic and simple method for calculation of pulsewidth modulation timings using only sampled reference values ( $v_\alpha$ and $v_\beta$) is proposed. This enables the scheme to be used for any closed-loop application such as vector control. In addition, a new method of switching technique is proposed, which ensures minimum switching while eliminating the fifth- and seventh-order harmonics and suppressing the eleventh and thirteenth harmonics, eliminating the need for bulky filters. The motor phase voltage is a 24-stepped waveform for the entire modulation range thereby reducing the number of switchings of the individual inverter modules. Experimental results for steady-state operation, transient operation, including start-up have been presented and the results of fast Fourier transform analysis is also presented for validating the proposed concept. [ABSTRACT FROM PUBLISHER]

This paper presents a 100-kW 100-kHz insulated-gate bipolar transistor (IGBT) series resonant inverter for induction heating applications that uses an improved power control scheme based on the standard pulse density modulation (PDM). This standard power control is a good solution for the design of high-frequency inverters because the output power factor is near to unity in a wide range of output power, resulting in great reduction of switching losses and electromagnetic noise. However, the output current can be in discontinuous mode, particularly for resonant loads of low quality factor or for low output power or low-load operation. This output current fluctuation produces a high output current ripple that can lead to an increase in power losses and loss of accuracy of the response of the frequency tracking control. The proposed control strategy, which is called enhanced PDM (EPDM), provides twice less output current ripple, thus resulting in an improved inverter behavior in terms of frequency tracking accuracy and energy efficiency. Experimental tests have been made, in order to compare the EPDM strategy with standard power control schemes. [ABSTRACT FROM PUBLISHER]

In this paper, the two-input buck converter is proposed as the dc/dc stage for photovoltaic (PV) cascaded converters. This converter is attractive for this application because it is cost effective and reliable and can achieve dual maximum power point tracking (MPPT) with only one power transistor. However, due to the simplified and integrated structure, the nonlinear characteristics of the converter and the two PV arrays complicate the control. By means of a small-signal modeling, the control theme of the two PV voltages is formulated, and the effect of the nonlinearities is presented. It is shown that, while fast voltage dynamics are achieved for the first input, the second-input voltage response depends on the second-stage converter control. Simulation and experimental results are reported to validate the theoretical analysis, showing the dual MPPT capability. [ABSTRACT FROM PUBLISHER]

Local dc distribution systems or dc nanogrids for residential and commercial buildings are growing popular due to the increased focus on energy savings. Using low-voltage dc for the nanogrid provides various advantages such as easier integration with renewable sources and battery banks, increased savings, etc. Future systems would use renewable sources and storage devices to become self-sufficient in generation with bare minimum consumption from the grid. The objective of this paper is to develop an energy management system (EMS) to provide uninterrupted power supply to the dc loads and achieve self-sufficiency by minimizing grid power consumption. This is achieved by developing a control scheme for a cascaded two-stage bidirectional converter interface between the nanogrid and the ac distribution network. In addition, an empirical relation for power flow through the converter is obtained, and an optimal capacitor link voltage range is derived to achieve power transfer between rated limits. The efficacy of the proposed control algorithm for the EMS is analyzed and proved to be well suited for the self-sustained dc nanogrid. A 5-kVA prototype of the converter is designed and developed in hardware, and the system operation is verified with experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes an improved performance interactive distribution static compensator (DSTATCOM) to address the limitations of conventional current control mode (CCM) and voltage control mode (VCM) operations. The proposed interactive scheme provides smooth transfer of modes of operation while remaining connected in the distribution system. In normal operation, the DSTATCOM operates in CCM to make source currents balanced, sinusoidal, and at a unity power factor. During voltage disturbances, the CCM operation cannot improve load voltage. In that case, DSTATCOM operation is changed to VCM, which maintains a constant voltage across the sensitive loads. Hence, this interactive DSTATCOM ensures continuous, flexible, and robust operation of the load. Moreover, the filter current requirements are reduced in the proposed scheme, which reduces the losses in the filter and feeder, improves inverter efficiency, and requires a reduced-rating inverter for sag mitigation. The principle of operation and control for both operating modes is analyzed. The detailed process of the flexible transfer between the two modes is derived. Deadbeat predictive control algorithms for CCM as well as VCM operation are developed for fast operation during mode transfers. The performance of the proposed scheme is validated by both simulation and experimental results. [ABSTRACT FROM PUBLISHER]

According to the requirement of fuel cell generation system, this paper presents a new single-stage and boost-voltage grid-connected inverter, as well as the signal modulation diagram in a line cycle. In the proposed inverter, one of the bridge legs is shared with a boost converter. The boost inductor current is designed in discontinuous conduction mode, which can effectively decrease low-frequency current ripple (LFCR) in the output current of the fuel cell. The switching modes of the proposed inverter are analyzed in positive and negative half line cycles, respectively. The LFCR in the output current of the fuel cell is analyzed, from which the design principle of the boost voltage inductor is obtained. The per-unit current values of the shared switches and the loss of the whole system are derived and compared with those of the conventional inverter. Experimental verifications are presented to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

This paper proposes a technique to suppress low-order harmonics for an open-end winding induction motor drive for a full modulation range. One side of the machine is connected to a main inverter with a dc power supply, whereas the other inverter is connected to a capacitor from the other side. Harmonic suppression (with complete elimination of fifth- and seventh-order harmonics) is achieved by realizing dodecagonal space vectors using a combined pulsewidth modulation (PWM) control for the two inverters. The floating capacitor voltage is inherently controlled during the PWM operation. The proposed PWM technique is shown to be valid for the entire modulation range, including overmodulation and six-step mode of operation of the main inverter. Experimental results have been presented to validate the proposed technique. [ABSTRACT FROM PUBLISHER]

In this paper, selective harmonic mitigation (SHM) and selective harmonic elimination (SHE) modulation techniques have been combined to produce appropriate pulses for a four-leg three-level neutral point clamped (NPC) inverter. In the proposed hybrid method, the SHM technique is applied to phase legs in order to mitigate non-triplen harmonics (fifth, seventh, $\ldots$) , and the fourth leg is controlled by the SHE principle to eliminate important low-order triplen harmonics (third, ninth, $\ldots$) completely. In this context, it is demonstrated that using SHM instead of an SHE modulator for phase legs leads to a reduced vast range of harmonic orders in the NPC output voltage, significantly. Moreover, it is proved that the presented hybrid switching technique has the ability of dc-bus capacitor voltage balancing, inherently. Furthermore, analyses are performed to calculate the dc-bus capacitances accurately to show 5% voltage ripple acceptably. Simulation and experimental results validate a good dynamic performance of the proposed hybrid modulation technique in firing the NPC inverter switches to generate low-harmonic voltage waveforms supplying balanced and unbalanced loads while balancing the dc capacitor voltages in a four-wire network with small dc-link capacitors. [ABSTRACT FROM PUBLISHER]

This paper proposes novel multilevel ac/dc/ac converters with reduced number of semiconductor devices to achieve light weight, efficiency, and better input current quality. The proposed three-phase front-end bidirectional five-level (5L) rectifier and rear-end 5L inverter are constructed based on multiple-pole multilevel diode-clamped (M2DCC) approach, which consist a total number of 24 diode components clamped. Based on the M2DCC concept, the number of switching devices can be further reduced to construct a new unidirectional front-end rectifier (M2SCR). Comparative studies are conducted to analyze the performances of the two proposed front-end rectifiers with supportive mathematical derivations. Experimental prototypes have proven the feasibility of the proposed ac/dc/ac configurations. Results obtained show that low current harmonic distortions of 5% and high power factor of 0.99 are achieved with small input inductors despite low-switching-frequency operation at 1 kHz. [ABSTRACT FROM PUBLISHER]

This paper proposes an improved half-bridge inverter with wide-input-voltage capability for ozone-driven circuits. The study is motivated because the limited regulation of input voltage often affects the operation flexibility of ozone-driven circuits. Therefore, a modification of a half-bridge inverter along with a multiwinding coil design is proposed in this study, anticipating an increase in the range of input voltage and benefiting the industry applications. To confirm the practicality of this method, a hardware circuit was made with extensive validation. Experimental outcomes support the feasibility of this proposed method for ozone generators, exhibiting a potential of the method extending to other voltage-source applications. [ABSTRACT FROM PUBLISHER]

Due to the higher attenuation of switching frequency current harmonics, the $LCL$ filter has been widely used in grid-connected inverters. To deal with the resonance of the $LCL$ filter, the capacitor current is usually fed back to damp the resonance actively. However, the computation and pulsewidth modulation (PWM) delays in the digital control system have a significant influence on the active damping method, resulting in poor system robustness. Meanwhile, these delays also reduce the control bandwidth greatly and thus impose a severe limitation on the low-frequency gains. In this paper, a real-time computation method with dual sampling mode is proposed to remove the computation delay from the inner active damping loop and the outer grid-current control loop simultaneously; thus, the system robustness and the control performance can be greatly improved. Moreover, the time duration between the sampling instant and the switching transition of the inverter bridge is extended by the proposed method, which effectively prevents the switching noise distorting the sampled signals. Therefore, the noise immunity of the inverter is also improved greatly. Experimental results from a 6-kW $LCL$-type single-phase grid-connected inverter confirm the theoretical expectations and the effectiveness of the proposed method. [ABSTRACT FROM PUBLISHER]

This paper presents a multifunctional onboard battery charger for plug-in electric vehicles (PEVs). The proposed battery charger consists of three H-bridge modules including a selective switch, a high-frequency transformer, and inductors. The first duty of the proposed charger is to charge the propulsion battery when PEV connects to the ac grid [onboard charger (OBC)]. In this case, the proposed charger plays a role in ac-to-dc converting with power factor correction. Occasionally, the propulsion battery can supply surplus energy to the grid [vehicle to grid (V2G)]. In this second task, the proposed charger acts as an inverter. The third role is to charge the auxiliary battery via the propulsion battery when PEV is in a driving state [low-voltage dc-to-dc converter (LDC)]. In this case, the proposed charger acts as a step-down converter. In conventional PEVs, the aforementioned functions are done by an OBC and an LDC separately. The proposed charger can implement the three tasks by sharing switches and inductors in an all-in-one system. Thus, the proposed approach can realize a small and light design of the EV battery charger, resulting in the improvement of fuel efficiency. After theoretical analysis, we carry out simulations and experiments using a prototype to verify the validity of the proposed approach. [ABSTRACT FROM PUBLISHER]

This paper presents an effective circuit configuration of a multilevel inverter that can increase the number of output voltage levels with a reduced number of circuit components. The proposed seven-level pulsewidth-modulation inverter consists of a single dc voltage source with a series of capacitors, diodes, active switches for synthesizing output voltage levels, and an H-bridge cell. After theoretical analysis, we carry out computer-aided simulations and experiments to verify the validity of the proposed approach. Here, we also introduce a modified switching strategy to solve the capacitor voltage unbalancing that occurs in series-connected capacitors. [ABSTRACT FROM PUBLISHER]

This paper presents a novel microinverter for a single-phase grid-connected photovoltaic (PV) system. The proposed microinverter consists of a step-up dc–dc converter using an active-clamp circuit with a series-resonant voltage doubler and a high-efficiency inverter with single-switch-modulation step-down converters. The active-clamp circuit provides zero-voltage switching (ZVS) turn-on, recycles the energy stored in the leakage inductance of the transformer, and limits switch voltage stress. Moreover, to remove the reverse-recovery problem of the rectifier diodes, a series-resonant voltage doubler is used. Thus, this whole process provides high efficiency. To improve efficiency and reliability in the proposed inverter, only a single switch is modulated at the switching frequency without a shoot-through problem. A modified controller is also adopted to achieve fast output control. Thus, the proposed PV microinverter has the structure to minimize power losses. The experimental results show a maximum efficiency of 96.2% for a 400-W microinverter. [ABSTRACT FROM PUBLISHER]

A switched boost inverter (SBI) can replace a $Z$-source inverter (ZSI) in low-power applications because it has one less $LC$ pair than the ZSI. This paper presents a class of quasi-SBIs (qSBIs) that offers several advantages when compared with a conventional SBI, including reducing the voltage stress on the capacitor, increasing the boost voltage factor, and improving input current profiles. Operating principles, steady-state analysis, and comparisons with conventional inverters are presented. A prototype based on a TMS320F28335 digital signal processor is built to verify the operating principle of the proposed qSBIs. [ABSTRACT FROM PUBLISHER]

The objective of this paper is to propose a new inverter topology for a multilevel voltage output. This topology is designed based on a switched capacitor (SC) technique, and the number of output levels is determined by the number of SC cells. Only one dc voltage source is needed, and the problem of capacitor voltage balancing is avoided as well. This structure is not only very simple and easy to be extended to a higher level, but also its gate driver circuits are simplified because the number of active switches is reduced. The operational principle of this inverter and the targeted modulation strategies are presented, and power losses are investigated. Finally, the performance of the proposed multilevel inverter is evaluated with the experimental results of an 11-level prototype inverter. [ABSTRACT FROM PUBLISHER]

In this paper, a predictive control scheme is proposed for the low-voltage ride-through (LVRT) enhancement of direct-driven permanent-magnet-synchronous-generator-based megawatt-level wind turbines. The proposed method uses the turbine–generator rotor inertia to store the surplus energy during the grid voltage dips. The power conversion system is realized using a three-phase diode-bridge rectifier, a three-level-boost converter, and a neutral-point-clamped (NPC) inverter. The wind turbine requirements, such as maximum power point tracking, net dc-bus voltage control, balancing of the dc capacitor voltages, and reactive power generation, are modeled as the reference control variables. The generator- and grid-side cost functions are defined to deal with these control objectives. During each sampling interval, the control goals are achieved based on the minimization of cost functions. The coordination of boost and NPC converters and the exchange of reference control variables during normal and LVRT operation are formulated such that the power converters operate in a safe mode while meeting the grid code requirements. Simulation and experimental results are presented to validate the proposed strategy. [ABSTRACT FROM PUBLISHER]

The voltage range of a renewable energy source, such as the photovoltaic cell, is influenced by the environment, light, temperature, and so on. The power conditioning system should adapt to the wide input voltage and have buck–boost ability. Based on the structure of the “ac/ac unit,” this paper presents a novel active buck–boost inverter (ABI) topology suitable for wide-range input, which can realize buck–boost conversion in a quasi-single-stage inverter. The ac/ac unit composed of active switches is utilized to perform voltage boost without introducing additional passive elements, which is in favor to the system power density and efficiency. Operational analysis in buck and boost modes are presented, and the modulation strategy applied in the ABI is also developed. Simulation and experimental results are presented to verify the operational principle and its modulation strategy. [ABSTRACT FROM PUBLISHER]

In this paper, two new topologies are proposed for multilevel inverters. The proposed topologies consist of a combination of the conventional series and the switched capacitor inverter units. The proposed topologies reduce the number of switches and isolated dc voltage sources, the variety of the dc voltage source values, and the size and cost of the system in comparison with the conventional topologies. In addition, the proposed topologies can double the input voltage without a transformer. There is no need for complicated methods to balance the capacitor voltage. The simulation and experimental results of single-phase 25- and 17-level inverters are given to prove the correct operation of the proposed topologies. [ABSTRACT FROM PUBLISHER]

High-boost dc-ac inverters are used in solar photovoltaic (PV), fuel cell, wind energy, and uninterruptible power supply systems. High step-up and step-down capabilities and shoot-through immunity are some of the desired properties of an inverter for a reliable, versatile, and low-distortion ac inversion. The recently developed Z-source inverter (ZSI) possesses these qualities. However, the realization of ZSI comes at a cost of higher passive component count as it needs two sets of passive filters. A switched boost inverter (SBI) has similar properties as ZSI, and it has one L\-C pair less compared to ZSI, but its gain is less than ZSI. This paper proposes the current-fed switched inverter (CFSI) which combines the high-gain property of ZSI and low passive component count of SBI. The proposed inverter uses only one L\-C filter and three switches apart from the inverter structure. The inverter topology is based on current-fed dc/dc topology. Steady-state analysis of the inverter is presented to establish the relation between the dc input and the ac output. A pulse width modulation (PWM) control strategy is devised for the proposed inverter. An experimental prototype is built to validate the proposed inverter circuit in both buck and boost modes of operation. A 353-V dc-link and a 127 V (rms) ac are obtained from a 35.3-V dc input to demonstrate the boost mode of operation. A 200-V dc-link and a 10.5-V (rms) ac are obtained from a 37.8-V dc input to verify the buck mode of operation of CFSI. [ABSTRACT FROM PUBLISHER]

In this paper, a model predictive scheme is proposed to control the grid-connected high-power four-level diode-clamped inverter. To predict the future behavior of active and reactive grid power values and dc link capacitor voltages, a discrete-time model of the inverter is developed in synchronous reference frame. The controller uses all the possible switching states of the inverter for the prediction and evaluates them using a cost function. The switching state, which minimizes the cost function, is then chosen and applied at the next sampling interval. The switching frequency minimization is also achieved by including an extra constraint in the cost function. A simplified extrapolation method with reduced computational burden is proposed to safeguard the semiconductor devices during the dynamic changes in reference power values. The performance of the proposed method is investigated with the perturbations in the grid filter and dc link parameters. The feasibility of the proposed method is verified through simulation and experimental results, showing good dynamic and steady-state performance. [ABSTRACT FROM PUBLISHER]

Loads connected to a stiff source cannot be protected from voltage disturbances using a distribution static compensator (DSTATCOM). In this paper, a new control-algorithm-based multifunctional DSTATCOM is proposed to operate in voltage control mode under stiff source. This scheme provides fast voltage regulation at the load terminal during voltage disturbances and protects critical loads. In addition, during normal operation, the generated reference load voltages allow control of the source currents. Consequently, DSTATCOM injects reactive and harmonic components of load currents to make source power factor unity. Simulation and experimental results are presented to verify the efficacy of the proposed control algorithm and multifunctional DSTATCOM. [ABSTRACT FROM PUBLISHER]

Induction heating systems are the technology of choice in many industrial, domestic, and medical applications due to its high performance. The core component of such systems is the power supply, which is usually composed of a rectifier stage and a resonant inverter. In order to simplify and further optimize the performance of the power supply, a class-E direct ac–ac converter featuring multicycle modulations is proposed in this paper. The proposed converter is composed of two switching devices that enable the direct ac–ac conversion. Single- and multicycle operation modes have been analytically described to prove the benefits, in terms of peak voltage reduction and output power control capabilities. A prototype featuring SiC junction-gate field-effect transistor devices, which perfectly fit these applications, has been designed and built to prove the feasibility of the proposed converter. The experimental results match the analytical results and validate the benefits of this converter. [ABSTRACT FROM PUBLISHER]

This paper presents a novel direct current-fed interleaved phase-modulated single-phase unfolding inverter for fuel-cell applications. Two active-clamped zero-voltage switching current-fed half-bridge isolated converters are interleaved in parallel input and series output configuration. Phase modulation is proposed to control these two converter cells, which generate a rectified sinusoidal pattern at the dc link. A simple H-bridge unfolding dc–ac inversion is used to produce single-phase sine voltage at line frequency switching using square-wave control. This not only simplifies the inversion stage in terms of modulation but also reduces the switching losses. Direct front-end current-fed based unfolding inverter is not reported in literature yet. Detailed analysis and design of the proposed direct current-fed single-phase unfolding inverter has been presented. Simulation waveforms using PSIM 9.0.4 are given to verify the presented analysis and design. Experimental results on a laboratory prototype rated at 200 W are demonstrated to support the investigation, to validate the accuracy of the proposed analysis and design, and to test the performance. [ABSTRACT FROM PUBLISHER]

This paper proposes the pulsewidth modulation (PWM) strategy of Z-source inverters (ZSIs) with minimum inductor current ripple. In existing PWM strategy with single-phase shoot-through, the shoot-through time interval is divided into six equal parts, therefore the three phase legs bear the equal shoot-through time interval. In this manner, the allotment and arrangement of the shoot-through state is easy to realize, but the inductor current ripple is not optimized. This causes to use relatively large inductors. In the proposed PWM strategy, the shoot-through time intervals of three phase legs are calculated and rearranged according to the active state and zero state time intervals to achieve the minimum current ripple across the Z-source inductor, while maintaining the same total shoot-through time interval. The principle of the proposed PWM strategy is analyzed in detail, and the comparison of current ripple under the traditional and proposed PWM strategy is given. Simulation and experimental results on the series ZSI are shown to verify the analysis. [ABSTRACT FROM PUBLISHER]

This paper systematically investigates the conducted electromagnetic interference (EMI) using separated heat sinks for a silicon carbide (SiC) JFET inverter for motor drives. The inverter circuit layout is implemented with discrete SiC JFETs attached on top of the heat sink, which creates extensive capacitive couplings and moreover increases parasitic oscillations. To minimize the influence, the solution of using separated heat sinks is proposed. For better common mode performance, the high-side heat sink is grounded to avoid fast dv/dts that occur between the drain of the lower switch and the low-side heat sink. For better differential mode performance, the RC snubber circuit and ferrite beads are used to damp parasitic oscillations. Two 2.2 kW inverter prototypes, with six discrete SiC JFETs on one common heat sink and separated heat sinks, respectively, are built using the same circuit layout. Their EMI spectra are compared under unfiltered and filtered conditions. The experiments show that the separate heat sinks inverter system exhibits significantly reduced EMI. Last, three improved solutions are proposed, which effectively suppresses the emitted EMI to the target level. [ABSTRACT FROM PUBLISHER]

Radio-frequency identification (RFID) technology has been widely used in passive RFID localization application due to its flexible deployment and low cost. However, current passive RFID localization systems cannot achieve both highly accurate and precise moving object localization task owing to tag collisions and variation of the behavior of tags. Most researchers increase the density of tag distribution to improve localization accuracy and then consider using either anti-collision process embedded in the hardware of the RFID reader or advanced localization algorithms to enhance localization precision. However, advanced anti-collision processes for RFID devices are challenged by the physical constraint characteristics of radio frequency; and improved localization algorithm cannot fundamentally reduce the impacts of tag collision on localization precision. This research work attempts to improve localization precision of a passive RFID localization system by using sparsely distributed RFID tags. This paper first defines a measure for accuracy and precision in a passive RFID localization system with regard to RFID tag distribution. An exponential-based function is then derived from experimental measurements, which reflects the relationship between RFID tag distribution and localization precision. This function shows that localization precision is mainly determined by tag density of RFID tag distribution. Based on the experimental findings, a sparse RFID tag distribution approach is proposed. The results show that in comparison with the conventional RFID tag distribution, passive RFID localization system with sparse RFID tag distribution can deliver a higher localization precision for the required accuracy. [ABSTRACT FROM PUBLISHER]

A new scheme for nine-level voltage space-vector generation for medium-voltage induction motor (IM) drives with open-end stator winding is presented in this paper. The proposed nine-level power converter topology consists of two conventional three-phase two-level voltage source inverters powered by isolated dc sources and six floating-capacitor-connected H-bridges. The H-bridge capacitor voltages are effectively maintained at the required asymmetrical levels by employing a space vector modulation (SVPWM) based control strategy. An interesting feature of this topology is its ability to function in five- or three-level mode, in the entire modulation range, at full-power rating, in the event of any failure in the H -bridges. This feature significantly improves the reliability of the proposed drive system. Each leg of the three-phase two-level inverters used in this topology switches only for a half cycle of the reference voltage waveform. Hence, the effective switching frequency is reduced by half, resulting in switching loss reduction in high-voltage devices. The transient as well as the steady-state performance of the proposed nine-level inverter-fed IM drive system is experimentally verified in the entire modulation range including the overmodulation region. [ABSTRACT FROM PUBLISHER]

Cascaded H-bridge multilevel power electronic converters generally require several dc sources. An alternative option is to replace all the separate dc sources feeding the H-bridge cells with capacitors, leaving only one H-bridge cell with a real dc voltage source. This will yield a cost-effective converter. However, the required capacitor voltage balancing is challenging. In this paper, using the phase-shift modulation approach, a new control method for cascaded H-bridge multilevel converters fed with only one independent dc source is presented. The proposed method has a wide voltage regulation range for the replacement capacitors in the H-bridge cells. Experimental and simulation results support the proposed control method. [ABSTRACT FROM PUBLISHER]

In this paper, a number of alternate-cascaded switched-inductor and tapped-inductor networks have been proposed for Z-source inverters. The resulting topologies have enhanced voltage-boost capability while retaining the usual voltage-buck flexibility of a conventional voltage-source inverter. The enhanced capability is achieved by using lower rated components that can more readily be found. These components are assembled without direct series connection and hence avoid unbalanced voltage sharing problems and losses linked to balancing resistive circuits. The component count is, however, high, meaning that the proposed inverters should only be considered when a design requires multiple lower rated components rather than a few higher rated ones. Analysis, simulation, and experimental results have already validated the concepts discussed. [ABSTRACT FROM PUBLISHER]

This paper presents a three-phase cascaded multilevel inverter that uses five-level transistor-clamped H-bridge power cells. Multicarrier phase-shifted pulse-width modulation method is used to achieve balanced power distribution among the power cells. A new method to balance the midpoint capacitor voltage in each cell is developed and tested. The analysis of the output voltage harmonics and the total power losses covering the conduction and the switching power losses are carried out and compared with the cascaded neutral-point-clamped and the conventional cascaded H-bridge inverters. For verifications, the proposed inverter is experimentally tested on an induction motor. From the results, the proposed inverter provides higher output quality with relatively lower power loss as compared to the other conventional inverters with the same output quality. [ABSTRACT FROM PUBLISHER]

The five-level active neutral-point (NP)-clamped (ANPC) converter is a newly emerging topology which can overcome the drawbacks of traditional NP-clamped and flying-capacitor multilevel converters. This paper presents a comprehensive theoretical analysis of the NP potential balancing issue and demonstrates that the NP potential can be naturally balanced under ideal and steady conditions. An NP potential balancing method based on zero-sequence voltage injection is presented. By calculating the average NP currents of all key zero-sequence voltages, the most appropriate zero-sequence voltage is selected to generate the demanded NP current, which can also limit the switching frequency of the series-connected insulated-gate bipolar transistors to the fundamental frequency. A three-phase five-level ANPC inverter prototype is built up, and both steady and dynamic experimental results are presented to verify the validity of this method. [ABSTRACT FROM PUBLISHER]

A neutral-point-clamped three-level inverter with small dc-link capacitors is presented in this paper. The inverter requires zero average neutral-point current for stable neutral-point voltage. The small dc-link capacitors may not maintain capacitor voltage balance, even with zero neutral-point current. This may happen due to nonlinearities present in the circuit. This requires a fast control of the neutral-point voltage. A simple carrier-based modulation strategy which allows modeling of the neutral-point voltage dynamics as a continuous function of power drawn from the inverter is proposed. This continuous model shows that the neutral-point current is proportional to the power drawn from the inverter, and it enables the use of a well-established classical control theory for the neutral-point voltage controller design. A simple proportional integral controller is designed for the neutral-point voltage control on the basis of the continuous model. The design method for optimum performance is discussed. The implementation of the proposed modulation strategy and the controller is very simple. The controller is implemented in a 7.5-kW induction machine-based drive with only 14 \mu \F dc-link capacitors. Also, the experimental results show that fast and stable performance of the neutral-point voltage controller are achieved and thus verify the validity of the proposed control approach. [ABSTRACT FROM PUBLISHER]

In this paper, two reduced switch count topologies are introduced for independently supplying two single-phase ac loads with one inverter. Using a new three-switch leg structure recently introduced and implemented in three-phase converters, two types of dual-leg and single-leg topologies are developed which respectively are functionally comparable to two full-bridge and half-bridge inverters working independently though with a less number of semiconductor switches and hence control and gate drive circuit components. The proposed six-switch and three-switch topologies are introduced; two modes of equal frequency and different frequency operation each of its own distinctive characteristics are considered for them and their pulse width modulation schemes are elaborated. Comprehensive analyses of power loss profile and output waveform properties are conducted via simulation for the proposed inverters, and the results are compared with full-bridge and half-bridge inverters. To assess the performance of the proposed inverter topologies, working prototypes are built, and the experimental results are provided. [ABSTRACT FROM PUBLISHER]

This paper presents a module-integrated isolated solar microinverter with pseudo-dc link. The studied grid-tied microinverters can individually extract the maximum solar power from each photovoltaic panel and transfer to the ac utility system. High conversion efficiency and high maximum power point tracking accuracy can be achieved with the studied pseudo-dc link topology. The operation principles and design considerations of the studied solar inverter are analyzed and discussed. A laboratory prototype is implemented and tested to verify its feasibility. [ABSTRACT FROM PUBLISHER]

Multilevel inverters have been widely accepted for high-power high-voltage applications. Their performance is highly superior to that of conventional two-level inverters due to reduced harmonic distortion, lower electromagnetic interference, and higher dc link voltages. However, it has some disadvantages such as increased number of components, complex pulsewidth modulation control method, and voltage-balancing problem. In this paper, a new topology with a reversing-voltage component is proposed to improve the multilevel performance by compensating the disadvantages mentioned. This topology requires fewer components compared to existing inverters (particularly in higher levels) and requires fewer carrier signals and gate drives. Therefore, the overall cost and complexity are greatly reduced particularly for higher output voltage levels. Finally, a prototype of the seven-level proposed topology is built and tested to show the performance of the inverter by experimental results. [ABSTRACT FROM PUBLISHER]

This paper is devoted to the step-up dc/dc converter family with a cascaded quasi-Z-source network (qZS-network). The cascaded (two-stage) qZS-network could be derived by the adding of one diode, one inductor, and two capacitors to the traditional quasi-Z-source inverter (qZSI). The proposed cascaded qZSI inherits all the advantages of the traditional solution (voltage boost and buck functions in a single stage, continuous input current, and improved reliability). Moreover, as compared to the conventional qZSI, the proposed solution reduces the shoot-through duty cycle by over 30% at the same voltage boost factor. Theoretical analysis of the two-stage qZSI in the shoot-through and non-shoot-through operating modes is described. The proposed and traditional qZS-networks are compared. A prototype of a step-up dc/dc converter with the cascaded qZS-network was built to verify the theoretical assumptions. The experimental results are presented and analyzed. Finally, a further optimization method of the cascaded qZS-network is proposed, and some practical design issues are discussed. [ABSTRACT FROM PUBLISHER]

This paper presents a novel single-stage charge-pump (CP) power-factor-correction (PFC) electronic ballast for metal halide (MH) lamps driven with the low-frequency square-wave current to avoid the acoustic-resonance problem. In order to achieve high power factor (PF) and meet the International Electrotechnical Commission (IEC) regulation, the CP PFC technique is applied to the full-bridge inverter of the conventional electronic ballast. Based on the analyses of the operational modes for the proposed electronic ballast, the design criteria of the CP components and the main inductor in the full-bridge inverter for the proposed electronic ballast are presented. A prototype circuit for a 35-W MH lamp is implemented to confirm the presented design criteria. [ABSTRACT FROM AUTHOR]

A novel switched-capacitor inverter is proposed. The proposed inverter outputs larger voltage than the input voltage by switching the capacitors in series and in parallel. The maximum output voltage is determined by the number of the capacitors. The proposed inverter, which does not need any inductors, can be smaller than a conventional two-stage unit which consists of a boost converter and an inverter bridge. Its output harmonics are reduced compared to a conventional voltage source single phase full bridge inverter. In this paper, the circuit configuration, the theoretical operation, the simulation results with MATLAB/SIMULINK, and the experimental results are shown. The experimental results accorded with the theoretical calculation and the simulation results. [ABSTRACT FROM PUBLISHER]

Power converters consisting of naturally commutated thyristors such as cycloconverters and current source inverters were the first to be used in driving electrical motors with variable speed, but now, due to their inferior performance compared to forced commutated converters, their use is restricted in the high voltage/high power range where the performance and cost of forced commutated switching devices are not yet competitive. Hybrid cycloconverters proposed recently are capable of improving the performance of cycloconverters by adding an auxiliary forced commutated inverter with reduced installed power. It will be shown that the new topology is not only able to improve the quality of the output voltage but is also able to enhance the control over the circulating current and, therefore, for some of the cycloconverter arrangements, to improve the input power quality. This paper evaluates the performance of a few standard and hybrid cycloconverter arrangements using both simulation and experimental results. [ABSTRACT FROM AUTHOR]

In this paper, two space-vector-based pulsewidth modulation (PWM) (SVPWM) strategies named equal- and proportional-duty SVPWMs are described, which are used to synthesize a four-level waveform from an open-end winding configuration of an induction motor. Two isolated dc-link voltages, which are in the ratio of 2 : 1, are employed to achieve this objective. Both of these PWM strategies achieve the avoidance of overcharging of the dc-link capacitor of an inverter operating with lower dc-link voltage by its counterpart with higher dc-link voltage. Implementation of these PWM strategies requires only the instantaneous three-phase reference voltages, eliminating the need of sector identification or lookup tables. The numbers of samples per cycle for individual inverters are selected in such a way that the quarter-wave, half-wave, and three-phase symmetries are achieved for the dual-inverter drive despite unequal dc-link voltages for the constituent inverters. It is also shown that one of the two PWM techniques, called the proportional-duty SVPWM, results in a better spectral performance and lower switching power loss in the overall dual-inverter system compared to the equal-duty SVPWM. [ABSTRACT FROM PUBLISHER]

With regard to a five-level inverter comprising flying-capacitor asymmetric H-bridge, the impact on the capacitor voltage under conventional modulation approach is analyzed. Since it is sensitive to the fundamental period and the load current, it may introduce undesired low-order harmonics into the output voltage and may even break down the power switches due to the considerable fluctuation of the flying-capacitor voltage. Thus, this paper proposes a novel pulsewidth-modulation scheme with the positive and negative cross carriers, which controls the flying-capacitor voltage by utilizing the redundant switching states of the output voltages. Three modes of precharging the flying capacitor without extra equipments are presented. Moreover, the capacitance of the flying capacitor and the switching frequency of the power switches can be chosen according to the allowable fluctuation of the flying-capacitor voltage and the load current. In order to remove the overlapping of the level layers, the optimization of the line-to-line voltage waveform is proposed to synthesize the reference vector with the “nearest three-vector” approach. The theory is supported by the experimental results from the prototype. [ABSTRACT FROM AUTHOR]

This paper proposes an energy regeneration circuit for three-phase voltage-fed inverters using a modified Undeland snubber. The proposed system uses a quasi-square-wave zero voltage switching dc–dc auxiliary converter to regenerate the energy from snubber capacitor to the dc bus. The regenerative circuit uses a single active switch, and it operates independently of the three-phase inverter. Operation stages, theoretical waveforms, and a design methodology are presented. Experimental results based on a 4.5-kVA three-phase inverter prototype are included to validate the proposed topology. [ABSTRACT FROM PUBLISHER]

This paper proposes a modified LLC resonant load configuration of a full-bridge inverter for induction-heating applications. The LLC load configuration is a combination of a series inductor, a matching transformer, and an inductor and a capacitor connected in parallel. The output power is controlled using the asymmetrical voltage-cancellation technique. With the use of a phase-locked loop control, the operating frequency is automatically adjusted to maintain a small constant lagging phase angle under load-parameter variation during the heating process. The proposed configuration has the benefit of smaller inductance and inherent short-circuit protection capability in case a short circuit occurs at the induction coil or from transformer saturation. The validity of the proposed method is verified through computer simulation and hardware experiment at an operating frequency range of 108.7–110.6 kHz. [ABSTRACT FROM AUTHOR]

Unipolar sinusoidal pulsewidth modulation (SPWM) full-bridge inverter brings high-frequency common-mode voltage, which restricts its application in transformerless photovoltaic grid-connected inverters. In order to solve this problem, an optimized full-bridge structure with two additional switches and a capacitor divider is proposed in this paper, which guarantees that a freewheeling path is clamped to half input voltage in the freewheeling period. Sequentially, the high-frequency common-mode voltage has been avoided in the unipolar SPWM full-bridge inverter, and the output current flows through only three switches in the power processing period. In addition, a clamping branch makes the voltage stress of the added switches be equal to half input voltage. The operation and clamping modes are analyzed, and the total losses of power device of several existing topologies and proposed topology are fairly calculated. Finally, the common-mode performance of these topologies is compared by a universal prototype inverter rated at 1 kW. [ABSTRACT FROM AUTHOR]

In this paper, a new five-level inverter topology for open-end winding induction-motor (IM) drive is proposed. The open-end winding IM is fed from one end with a two-level inverter in series with a capacitor-fed H-bridge cell, while the other end is connected to a conventional two-level inverter. The combined inverter system produces voltage space-vector locations identical to that of a conventional five-level inverter. A total of 2744 space-vector combinations are distributed over 61 space-vector locations in the proposed scheme. With such a high number of switching state redundancies, it is possible to balance the H-bridge capacitor voltages under all operating conditions including overmodulation region. In addition to that, the proposed topology eliminates 18 clamping diodes having different voltage ratings compared with the neutral point clamped inverter. On the other hand, it requires only one capacitor bank per phase, whereas the flying-capacitor scheme for a five-level topology requires more than one capacitor bank per phase. The proposed inverter topology can be operated as a three-level inverter for full modulation range, in case of any switch failure in the capacitor-fed H-bridge cell. This will increase the reliability of the system. The proposed scheme is experimentally verified on a four-pole 5-hp IM drive. [ABSTRACT FROM PUBLISHER]