Search

In this paper, a new modular and active snubber cell, easily applicable, and attractive for converters, especially have many switches proposed. This snubber cell is implemented on the single phase of a grid-connected three-phase T-type three-level inverter (T-3LI). In this new converter, the main switches turn-on under zero-voltage transition and turn-off under zero-voltage switching (ZVS). Also, auxiliary switches turn-on under zero-current switching and turn-off under ZVS. All snubber diodes operate under soft switching (SS). There are no additional current and voltage stresses on the main switches. During an SS operation, the switching energies are transferred to a dc voltage source. Then, these energies are processed to input with an independent dc–dc converter. Thus, all switching energies are recycled. In this paper, the principle operation and steady-state analysis of the modular and active snubber cell for a single-phase T-3LI are presented and experimental results, rated 1 kW and 100 kHz, are provided to verify theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper presents a unified second-stage LC filter applied in the three-state switching cell buck–boost converter, which provides current and voltage with low ripple and low noise. The unified second-stage filter promotes a reduction in the number of devices while maintaining the filtering performance of the converter, with second-stage LC filters at the input and at the output. Moreover, the unified filter, when associated with a three-state switching cell buck–boost converter, allows a size reduction of filter devices, especially for designs with duty cycle range around 1/2. Furthermore, the unified filter arrangement provides nondissipative clamping of switching devices and reduce the system order when compared to the converter with second-stage LC filters. In this paper, the static and dynamic characteristics of the proposed converter in continuous conduction mode (CCM) are reported. Experimental data were obtained from a laboratory prototype with an input range of 32 $\sim$ 72 V, constant output of 48 V, a load of 150 W, and switching frequency of 45 kHz. The measured efficiency for the rated load was 97% for maximum input voltage. A comparison of the size and performance of the proposed filter with the topology that uses second-stage LC filters at the input and at the output is also presented. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

This paper presents a novel integrated-stage light-emitting diode (LED) driver based on Flyback and resonant converters. The Flyback converter realizes power factor correction in the discontinuous conduction mode. The resonant converter is operated as a dc–dc converter to support the LED loads. Moreover, the resonant converter can clearly decrease the drain–source voltage of the active switch and exhibits zero-voltage-switch characteristics. Therefore, a cost-effective MOSFET can be chosen as the main control component that can decrease the cost of the whole system. Compared to a single-active-switch converter (such as Class-E converter), the number of passive components in the resonant converter can be limited to four. Therefore, the power density of the system can be improved drastically. In this paper, a 100-W prototype is presented under the experimental condition to validate the proposed integrated-stage LED driver. [ABSTRACT FROM AUTHOR]

In this paper, a series-capacitor-based interleaving buck power factor correction (PFC) converter is proposed, the intermediate energy storage capacitance of which is operated at discontinuous capacitor voltage mode (DCVM), and automatic power factor (PF) correction for this converter is obtained. Moreover, the voltage across the series capacitor of the proposed PFC converter is clamped at the input voltage, and thus peak voltage stress existed in the traditional DCVM buck PFC could be relieved. By effectively regulating the charge/discharge time for the series capacitor, ultrahigh step-down conversion ratio of the proposed converter is achieved, the conversion ratio of which is independent of the duty cycle and only related to the switching frequency and circuit parameters. Therefore, high PF can be obtained due to very narrow deadtime of the input current. Meanwhile, the proposed PFC converter can realize the soft turn-on of part power switch and soft turn-off of part power diodes. In addition, comparing with the traditional discontinuous inductor current mode PFC, the input current of the proposed PFC converter is continuous so that the peak value and root-mean-square value of input current can be reduced. The operational principle, performance analysis, and parameter design principle are given in this paper. The analysis results show that the PF and total harmonic distortion are also independent of the duty cycle. Finally, a 220-Vac input, 60 W/15 V output experimental prototype is built to verify the validity of the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

A new isolated single-stage soft-switching power-factor-correction (S4 PFC) driver for supplying light-emitting diodes (LEDs) is introduced in this paper. In the proposed LED driver, the switches voltage stress and also the dc-bus voltage is limited to the peak of the line voltage. Hence, low voltage rated mosfets and diodes can be used. The efficiency is improved because the switches are turned on under zero current switching (ZCS) condition and turned off under zero voltage zero current switching (ZVZCS) condition. Also, no current feedback is required since the converter provides an output current independent of output voltage. In this paper, operating principle of the proposed LED driver is presented and design considerations are discussed. To verify the theoretical analysis, a laboratory prototype of the proposed converter for supplying a 50 W/70 V LED module from 220 Vrms/50 Hz ac mains is implemented, and the experimental results are presented. Since current feedback is not used, dimming property and operation for universal voltage range is not achievable. [ABSTRACT FROM PUBLISHER]

In this paper, a nonisolated dc–dc converter with high voltage gain is presented. Three diodes, three capacitors, an inductor, and a coupled inductor are employed in the presented converter. Since the inductor is connected to the input, the low input current ripple is achieved, which is important for tracking maximum power point of photovoltaic panels. The voltage stress across switch S is clamped by diode D 1 and capacitor C1. Therefore, a main switch with low on-resistance RDS (on) can be employed to reduce the conduction loss. Besides, the main switch is turned on under zero current. This reduces the switching loss. The steady-state analysis of the proposed converter is discussed in this paper. Finally, the proposed converter prototype circuit is implemented to justify the validity of the analysis. [ABSTRACT FROM PUBLISHER]

This paper presents three unidirectional step-up ac–dc converter topologies with voltage multiplication on their outputs. The first topology is the hybrid boost rectifier and the other two are novel bridgeless structures, all based on the integration of boost rectifier and the ladder switched-capacitor (SC) cell. The new hybrid structures provide high voltage gain with low voltage stress across the switches, high-power factor, and output voltage regulation. This paper presents the principle of operation, steady-state and dynamic analysis, design methodology, and experimental verification. A different approach is also presented for the design methodology of the SC cell and for the analysis of its influence on the dynamic model. Three 1000-W prototypes with a 220-V input voltage, 800-V output voltage, and 100-kHz switching frequency were designed to corroborate the theoretical study. The best efficiency was 97.1$\%$ in the proposed bridgeless versions and the voltage stress across the switches stands around 400 V. Furthermore, a comparison between the proposed structures and previous topologies is also presented. [ABSTRACT FROM PUBLISHER]

This paper proposes a family of soft-switching bidirectional converters. In many applications, the bidirectional converters operate over a wide range of duty cycle and load variations. In the proposed converters, in order to extend the zero-voltage switching operation range, two supplemental voltage sources utilizing passive components are implemented in the auxiliary circuit. By using this method, the soft-switching features are ensured for an extensive range of the converter duty cycles. This is achieved independent of the output power value or the converter operation mode, and so, soft switching is ensured within the entire converter operating region. In these converters, all semiconductors components are soft switched, and the auxiliary circuit does not contribute to the complexity of the control circuit. Also, no extra voltage stress exists on the main switches and the voltage stress on the auxiliary switches is lower than the main switches voltage stress. In this paper, the proposed bidirectional buck/boost converter is analyzed and to confirm the feasibility of the proposed method, experimental results of a 150-W prototype converter are presented. [ABSTRACT FROM PUBLISHER]

Multilevel inverters (MLI) with reduced components are becoming popular to achieve higher voltage levels with lower cost and complexities of the circuit. Most of the reduced switch MLIs use a large number of isolated voltage sources that have a large total standing voltage (TSV) and higher losses. Moreover, many reduced component MLIs have been developed to reduce the number of switches only and have not utilized the dc-link voltages properly. Thus, an inverter needs to be designed in which the number of dc sources is also small and utilized fully. In this paper, a novel single-phase, multicell MLI configuration is presented that can generate a maximum number of output voltage levels using a minimum number of switches and dc sources. Two optimal configurations of the proposed MLI are proposed based on the minimum requirements of components with the optimum voltage stress of the highest rated switches. Moreover, the TSV of the proposed optimal MLI also becomes low. A generalized multicell optimum MLI is presented and the number of components, voltage stress of all the switches, and the TSV of the proposed as well as the other inverters also determined by the generalized expressions for comparison purpose. The prototype of a specimen 15-level inverter and the optimal 75-level inverter cell is further developed and implemented using DS 1103 in the laboratory to show the effectiveness of the proposed configuration. The experimental results corresponding to the different modulation indices are presented here for the verification of the simulation results. [ABSTRACT FROM AUTHOR]

In this paper, a new transformerless buck–boost converter based on a ZETA converter is introduced. The proposed converter has the ZETA converter advantages, such as buck–boost capability, input-to-output dc insulation, and continuous output current. The suggested converter voltage gain is higher than the classic ZETA converter. In the presented converter, only one main switch is utilized. The proposed converter offers low voltage stress of the switch; therefore, the low on-state resistance of the main switch can be selected to decrease the losses of the switch. The presented converter topology is simple; hence, the control of the converter is simple. The converter has the continuous output current. The mathematical analyses of the presented converter are given. The experimental results confirm the correctness of the analysis. [ABSTRACT FROM AUTHOR]

Circuit analysis and design criteria of a two-phase bidirectional converter with high voltage gain are presented in this paper. The operating principle of the forward or reverse mode is similar to that of the conventional buck or boost converter. Compared with the conventional converter, the switch stresses can be reduced significantly depending on the operating region of the voltage ratio in the two-phase converter. The power losses can also be reduced due to the use of low-voltage rating switches. The derivate converters are discussed to demonstrate the advantages of the proposed topology. A 200 W/1 MHz two-phase prototype converter with gallium nitride (GaN) devices is built and tested to verify the feasibility. [ABSTRACT FROM AUTHOR]

This paper proposes a novel isolated high step-down conversion circuit, called an integrated buck and modified push−pull (IBMPP) converter, which is able to lower the voltage level on the primary side of the ideal transformer, resulting in a lower turns-ratio and decreased leakage inductance. The IBMPP converter is able to prevent the duty cycle from operating in extremely low conditions. Furthermore, the proposed converter adopts active-clamp techniques to recycle leakage energy and to suppress voltage spikes, so that the conversion efficiency can be effectively improved. The advantages of the IBMPP converter are its simple topology, easy control mechanism (which requires only two signals with a 180-degree phase shift), high conversion ratio, low component counts for power switches, and less voltage stress on some of the switches on the high-voltage side. The operation principle, steady-state analysis, design considerations, and experimental results of the proposed IBMPP converter are presented in detail. The feasibility of the IBMPP is verified by hardware implementation. The full-load efficiency at 250 W is 81.44%, and the input and output voltages are 380 and 5 V, respectively. [ABSTRACT FROM AUTHOR]

In this paper, a new high voltage gain step-up dc–dc converter is proposed for interfacing renewable power generation. The configuration optimally integrates both the coupled-inductor and switched-capacitor techniques to achieve an ultra-high step-up gain of voltage conversion with low voltage stress and high efficiency. It consists of a voltage boost unit, a passive clamp circuit, and a symmetrical voltage multiplier network. The structure becomes modular and extendable without adding any extra winding for ultra-high step-up voltage gain. The proposed topology not only reduces the voltage stress on the main switch but also maintains it steady for the entire duty cycle range. Furthermore, the reverse recovery issue of the diodes is alleviated through the leakage inductance of the coupled inductor. The operation principle and steady-state analysis are presented in detail. Experimental evaluation validates the claimed advantages and demonstrates a well-distributed efficiency curve and the peak of 96.70%. [ABSTRACT FROM AUTHOR]

This paper presents a novel switch current stress reduction technique for a single switch boost-flyback high step up dc–dc converter. Coupled inductor-based converters do not have a sufficiently higher inductance value of their windings. This creates current surge during transient and steady state, which in turn increases current stress at main switch. To compensate this difficulty in coupled inductor-based boost flyback converter, an inductor–diode parallel combination has been connected in series with the switch. This technique increases the effective inductance of the coupled inductor primary winding during switch turn-on operation and helps to reduce current stress. Steady-state operating principle with the proposed technique is analyzed in continuous conduction mode. The current reduction technique is discussed with a proper mathematical derivation. To verify theoretical findings, simulation study is carried out in MATLAB/Simulink R2014b. Finally, a laboratory-based 40-W prototype converter is designed to show the effectiveness of the proposed switch current reduction technique. [ABSTRACT FROM AUTHOR]

A new transformerless bidirectional buck-boost converter is proposed in this paper. The proposed converter has a simple circuit structure, low component count, low voltage stress on the power transistors, and a wide voltage gain range. This makes it applicable in the energy storage charge/discharge systems, such as electric vehicles (EV), microgrids and nanogrids with energy storage units, and uninterruptible power supplies. In addition, synchronous rectification between the complementary transistors is employed to improve the converter efficiency. A comprehensive analysis of the steady-state operation, small-signal model, component parameters design, and efficiency analysis of the proposed converter operating in a continuous conduction mode is given. Finally, a 1.6-kW scaled-down prototype was built using Silicon Carbide MOSFETS to validate the effectiveness and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, a nonisolated bidirectional dc–dc converter is presented. The proposed converter consists of two boost converters to enhance the voltage gain. Four power switches with their body diodes are employed in the proposed converter. Also, two inductors and a capacitor are used as passive components. The input current is divided to the inductors which causes the efficiency to be high. The voltage gain of the proposed converter is higher than the conventional cascaded bidirectional buck/boost converter (CCBC) in step-up mode. Besides, the voltage gain in step-down mode is lower than CCBC. Besides, the efficiency of the proposed converter more than CCBC while the total stress on active switches are same. The simple structure of the proposed converter causes its control to be easy. The steady-state analysis of the proposed converter is discussed in this paper thoroughly. The stress on converters’ devices and the efficiency of the proposed converter and CCBC are compared in this paper. Finally, the proposed converter prototype circuit is implemented to justify the validity of the analysis. [ABSTRACT FROM PUBLISHER]

In this paper, a new multi-input multi-output (MIMO) dc–dc converter with high step-up capability is proposed for wide power ranges. Also, in order to increase each output voltage, diode–capacitor voltage multiplier (VM) stages are utilized in the proposed converter. The number of input stages, output stages, and VM stages are arbitrary and dependent on design conditions. At first, the general structure of proposed MIMO converter is presented. Then, in order to explain the converter operation, we walk through the design of a 1-kW four-input two-output example, including loss and efficiency calculations. We validate the design with a prototype that matches efficiency calculations. [ABSTRACT FROM AUTHOR]

This paper presents a new reconfiguration module for asymmetrical multilevel inverters in which the capacitors are used as the dc links to create the levels for staircase waveforms. This configuration of the multilevel converter makes a reduction in dc sources. On the other hand, it is possible to generate 13 levels with lower dc sources. The proposed module of the multilevel inverter generates 13 levels with two unequal dc sources (2VDC and 1VDC). It also involves two chargeable capacitors and 14 semiconductor switches. The capacitors are self-charging without any extra circuit. The lower number of components makes it desirable to be used in wide range of applications. The module is schematized as two back-to-back T-type inverters and some other switches around it. Also, it can be connected as a cascade modular which leads to a modular topology with more voltage levels at higher voltages. The proposed module makes the inherent creation of the negative voltage levels without any additional circuit (such as H-bridge circuit). Nearest level control switching modulation scheme is applied to achieve high-quality sinusoidal output voltage. Simulations are executed in MATLAB/Simulink and a prototype is implemented in the power electronics laboratory in which the simulation and experimental results show a good performance. [ABSTRACT FROM AUTHOR]

The interleaved bidirectional buck–boost converter dual active half-bridge (IBBC-DAHB) dc–dc converter consists of two converters IBBC and DAHB and a coupled inductor. The IBBC-DAHB converter has significant features such as low ripple current at the low-voltage side, low current stress on the input inductors, voltage stress across the switches less than the high-voltage side, high voltage gain, and zero-voltage soft switching. The converter offers high efficiency using phase-shift modulation when it operates at a nominal design operating point. However, the efficiency decreases due to high circulating current, high current stress, and limited soft-switching range when the source and load voltages deviate from their nominal values. This paper employs both duty cycle and phase-shift modulation methods to improve the above mentioned shortcomings using voltage matching for the DAHB converter. The proposed converter is analyzed and a 500-W experimental prototype with 40–60 V input voltage and 400 V output voltage under 100 kHz switching frequency is implemented to verify the theoretical results. The maximum efficiency of 97.15% is achieved at 60 V and 400 W. A flat efficiency characteristic for the converter is derived by the proposed control method, where the efficiency at 20% of nominal load is 91% and much higher than the phase-shift control, which is 70.8%. [ABSTRACT FROM AUTHOR]

A nonisolated bidirectional dc–dc converter with high voltage gain, low voltage stress, low component count, and soft-switching features is presented in this paper. In this topology, coupled inductors and voltage multiplier cells are merged to achieve high step-up/down voltage gain. Also, due to using active clamp circuits, the voltage stress of power switches is relatively low. Thus, the low voltage switches with low on-resistance can be employed to reduce the conduction losses. Furthermore, zero-voltage switching is accomplished in both high step-up and high step-down modes for all power switches, and due to zero-current switching operation of all antiparallel diodes, the reverse recovery losses are reduced. In order to verify the theoretical analysis and the converter performance, a 200 W prototype circuit of the proposed converter is implemented in the laboratory. [ABSTRACT FROM AUTHOR]

In this paper, a high step up converter consisting of an integrated quadratic-boost converter and a voltage doubler is proposed. The integration of the quadratic-boost converter makes the system easier to lift up its voltage gain through slightly increasing the duty ratio of the single switch. The voltage doubler further increases the voltage gain of the system as the turn ratio rises. The voltage stresses on the switch and the diodes are decreased for such cascaded topology. Different operation modes are analyzed and mathematical analysis of the converter is presented in detail. The leakage inductance contributes to realizing zero current switching of the diodes in the second boost stage and the doubler and the energy can be recycled to the load. A 38-W prototype is built to work as a vehicle LED driver. Experiments are conducted to verify the advantages of the proposed converter and the efficiency is 90% at the nominal operating point. [ABSTRACT FROM AUTHOR]

This paper explores a power-conversion system for single-phase transformerless ac module application. A nonisolated high-gain dc–dc stage is coupled with a doubly grounded dynamic dc-link inverter to implement the microinverter topology. The front-end boost stage steps up the single-module voltage to a higher dc voltage, typically to 200 or 400 V as required for the following inverter stage. It is a hybrid of an interleaved boost and switched capacitor concept capable of achieving high gain while simultaneously maintaining reduced voltage and current stress, and thus lowering switching and conduction loss for most of the switches. By directly connecting the grid neutral to the photovoltaic (PV) negative, the doubly grounded voltage swing inverter has the advantage of zero capacitive-coupled common-mode ground currents, critical for transformerless PV inverters. The two dc links of the inverter stage share the double-line frequency power decoupling with a combination of higher value of mean voltage and relatively large 120-Hz ripple component–the dynamic dc-link approach. Through an optimization algorithm, the decoupling capacitance is minimized enabling an all-film capacitor implementation while satisfying the converter's operating constraints over a wide range of power factors. The simulation as well as experimental results from a GaN-based hardware prototype validate the converter's performance. [ABSTRACT FROM AUTHOR]

A 1-MHz-modified single-ended primary-inductor converter (SEPIC) circuit is presented in this paper as an LED driver for automotive headlights. On the basis of traditional SEPIC, only a diode and two capacitors are added; therefore, the circuit structure is relatively simple and the volume is relatively small. High step-up capability is obtained with moderate duty cycle. Compared with traditional step-up circuit such as boost, low-voltage stress is gained which is beneficial to device selection. Zero-voltage switching is achieved at the same time to reduce switching loss. Planar inductors are used with the advantages of low profile and good thermal characteristic. Operational principle and parameters design process are introduced in detail. A 36-W prototype has been designed to demonstrate theoretical analysis. Obtained efficiency was up to 90.91% at full load. [ABSTRACT FROM AUTHOR]

High step-up converters are required for distributed photovoltaic generation systems, due to the low voltage of the photovoltaic source. In this paper, a new hybrid high voltage gain dc–dc converter is created by merging the standard boost converter with a coupled inductor and different switched-capacitor techniques. With a single switch and no requirement of higher duty cycle values, the proposed converter achieves a high voltage gain and high efficiency, in addition to lowered voltage and current stresses of the components. A 200-W prototype was implemented experimentally to evaluate the converter, which reached a maximum efficiency of 97.6%. [ABSTRACT FROM AUTHOR]

In this paper, a hybrid switched-capacitor/switched-quasi-Z-source bidirectional dc–dc converter is proposed for electric vehicles (EVs) with hybrid energy sources, which has a wide voltage gain range in the bidirectional energy flows. Compared with the traditional quasi-Z-source bidirectional dc–dc converter, the proposed converter only changes the position of the main power switch and employs a switched-capacitor cell at the output of the high-voltage side. Therefore, the advantages of the wide voltage gain range and the lower voltage stresses across the power switches can be achieved. The operating principle, the voltage and current stresses across the power switches, and the comparisons with other converters are analyzed in detail. Furthermore, the parameter design of the main components, the dynamic modeling analysis, and the voltage control scheme are also presented. Finally, the experimental results obtained from a 400 W prototype validate the characteristics and the theoretical analysis of the proposed converter. [ABSTRACT FROM AUTHOR]

Soft-switching inverters can achieve high efficiencies and low switchdv/dtanddi/dt, but often impose additional stress on the switches due to their resonant behavior. Multicell converters, on the other hand, can process high voltages by arranging the switches to share the stress. This paper proposes a buck–boost multicell soft-switching inverter with inherent cell voltage balancing. Both the current and voltage stresses are shared by the cells. Soft-switching conditions are achieved for all switching transitions without any need for auxiliary circuitry or clamps. A multiple-winding transformer transfers energy between the terminals and provides galvanic isolation. An analytical study and experimental results on a 1200-W prototype verify the operation of the inverter. [ABSTRACT FROM AUTHOR]

In this paper, a novel buck–boost converter with low electric stress on components and negative output voltage is proposed. The operational principle, steady-state analysis, and small-signal modeling of the proposed buck–boost converter in continuous conduction mode are presented. Comparisons among another five buck–boost converters and the proposed buck–boost converter are presented. It is found that the proposed converter's voltage gain is smaller than the other converters’ in step-down mode. Also, based upon the comparisons among the same kind and same number of components, the voltage and current stresses on the power switch of the proposed buck–boost converter are less than or equal to those of the comparative converters, and the voltage stress on the charge pump capacitor and the switching device power rating of the proposed buck–boost converter are always lower than those of other comparative converters. The efficiency of the proposed buck–boost converter is highest among those converters having the same number of elements. These advantages make component selection for the proposed converter much easier, and it can be used directly in applications needing a negative voltage source. Finally, simulation results and circuit experiments are given for validating the effectiveness of the proposed buck–boost converter. [ABSTRACT FROM AUTHOR]

In this paper, a family of automatic interleaved Dickson switched-capacitor converters (AIDSCC) and its zero-voltage switching (ZVS) resonant configuration are proposed. Different from the traditional Dickson switched-capacitor converter, the AIDSCC has symmetrical configuration with the features of automatic interleaved input current, small output voltage ripple, and lower peak capacitor voltage stress. To improve the line regulation capability, one small resonant inductor is inserted and two bulky capacitor banks are replaced by two much smaller resonant capacitors, forming the resonant AIDSCC. The transistors are ZVS turned on and diodes are zero-current switching turned off by operating above the resonance. With frequency modulation within a reasonable range, the voltage-gain range of the resonant AIDSCC is expanded significantly, while sacrificing the maximum efficiency due to the higher conduction loss. A 3X AIDSCC and a 3X resonant AIDSCC below 140 W were built to verify the analysis. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high step-up dc–dc converter is proposed. Active–passive inductor cells (APICs) are used to extend the topology. The ability to achieve high gains is the main merit of the proposed topology. The proposed converter operates based on parallel charging and series discharging of the inductors. The converter also achieves high step-up voltage gain with appropriate duty cycle and low voltage and current stress on the power switches and diodes. The proposed converter is analyzed in operation modes. The main parameters of the converter such as voltage gain, voltage stress of semiconductor devices are calculated to compare with other structures. Considering the output voltage ripple and filter size, the proposed converter is designed. Moreover, the losses and efficiency of the converter are calculated. The performance of the proposed converter is validated by experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a novel nonisolated single-input dual-output three-level dc–dc converter (SIDO-TLC) appropriate for medium- and high-voltage applications. The SIDO-TLC is an integration of the three-level buck and boost converters, whose output voltages are regulated simultaneously. Reducing voltage stress across semiconductor devices, improving efficiency, and reducing inductors size are among the main merits of the new topology. Moreover, due to the considerably reduced volume of the step-down filter capacitor, a small film capacitor can be used instead, whose advantages are lower equivalent series resistance and a longer lifespan. A closed-loop control system has been designed based on a small-signal model derivation in order to regulate the output voltages along with the capacitors’ voltage balancing. In order to verify the theoretical and simulation results, a 300-W prototype was built and experimented. The results prove the aforementioned advantages of the SIDO-TLC, and the high effectiveness of the balancing control strategy. Furthermore, the converter shows very good stability, even under simultaneous step changes of the loads and input voltage. [ABSTRACT FROM AUTHOR]

Single-stage power-factor-corrected (S2PFC) power supplies usually suffer from high voltage stress, due to lack of control on the intermediate bus capacitor voltage. In the past, analysis of such voltage stress was mostly based on steady-state condition without providing sufficient explanation during the transient circuit operation. This paper revisits the problem at circuit level and reports that the root cause is due to the inherent negative current feedback property of the output inductor or the transformer operating in continuous conduction mode (CCM). Based on the finding, this paper further proposes a new approach to reducing the voltage stress by adding an auxiliary circuit branch to existing S2PFC converters. The additional circuit branch limits the effect of negative current feedback by suppressing the change of output current slope due to change of load. This assists the pulsewidth modulation controller to track the change of load better such that the bus capacitor voltage range is reduced through duty cycle control. The auxiliary circuit branch also reduces reverse-recovery-related losses of the converter under CCM operation. A laboratory prototype using the popular boost PFC converter combined flyback dc/dc converter was built and tested to confirm the analysis and effectiveness of the approach. [ABSTRACT FROM AUTHOR]

This paper proposes an interleaved buck converter (IBC) with continuous input current, extremely low output current ripple, low switching losses, and improved step-down conversion ratio. Unlike the conventional IBC, the proposed converter has a continuous input current, and its output current ripple is extremely low. The proposed converter has a lower voltage stress in comparison to the conventional IBC and can also provide a high step-down ratio, which makes it a proper choice for high-power applications where a nonisolated step-down converter with low output current ripple and continuous input current is required. Also, the proposed converter can provide current sharing between two interleaved modules without using additional current-sharing control method. All of these benefits are obtained without any additional stress on the circuit components. A prototype converter with 200-V input and 24-V–10-A output is implemented to verify the theoretical analysis. Operational principles and experimental results are presented in this paper. [ABSTRACT FROM PUBLISHER]

In this paper, a novel transformerless interleaved high step-down conversion ratio dc–dc converter with low switch voltage stress is proposed. In the proposed converter, two input capacitors are series-charged by the input voltage and parallel-discharged by a new two-phase interleaved buck converter for providing a much higher step-down conversion ratio without adopting an extreme short duty cycle. Based on the capacitive voltage division, the main objectives of the new voltage-divider circuit in the converter are for both storing energy in the blocking capacitors for increasing the step-down conversion ratio and reducing voltage stresses of active switches. As a result, the proposed converter topology possesses the low switch voltage stress characteristic. This will allow one to choose lower voltage rating MOSFETs to reduce both switching and conduction losses, and the overall efficiency is consequently improved. Moreover, due to the charge balance of the blocking capacitor, the converter features automatic uniform current sharing characteristic of the interleaved phases without adding extra circuitry or complex control methods. The operation principles and relevant analysis of the proposed converter are presented in this paper. Finally, a 400-V input voltage, 25-V output voltage, and 400-W output power prototype circuit is implemented in the laboratory to verify the performance. [ABSTRACT FROM PUBLISHER]

High-gain voltage conversion is a feature required for several applications, especially for power processing of low-voltage renewable sources in grid-connected systems. In this scope, the presented paper proposes a novel transformerless high gain step-up dc–dc converter based on an active switched-inductor and a passive switched-capacitor networks. The main advantages of the proposed converter are the high voltage gain (>10), the reduced voltage stresses across the switches and the reduced number of components when compared to topologies that provide the same voltage gain using similar principles. The detailed analysis of the proposed converter and a comparison considering other topologies previously published in the literature are also presented in this manuscript. In order to verify the proposed converter performance, a prototype has been built for a power of 200 W, input and output voltages of 20 and 260 V, respectively, and switching frequency of 50 kHz. Experimental results validate the effectiveness of the theoretical analysis proving the satisfactory converter performance, which peak efficiency is around 95.5%. [ABSTRACT FROM PUBLISHER]

In this paper, two switched-capacitor quasi-switched boost inverters (qSBIs) are proposed. By adding one capacitor and one diode to the qSBIs, the proposed inverters achieve high voltage gain with low voltage stress on active switches, capacitors, and diodes. The proposed inverters can extend to n-cell for voltage gain improvement. The operating principle, steady-state analysis, and impedance parameter selections of the proposed inverter are presented. A full comparison between the proposed inverter and other impedance-source inverters is addressed. A 500-W prototype is built to verify the operating theory of the proposed inverter in both the standalone mode and the grid-connected mode. Simulation and experimental results validate the theoretical analysis. [ABSTRACT FROM PUBLISHER]

A common ground switched-quasi-Z-source bidirectional dc–dc converter is proposed for electric vehicles with hybrid energy sources. The proposed converter is based on the traditional two-level quasi- Z-source bidirectional dc–dc converter, changing the position of the main power switch. It has the advantages of a wide-voltage-gain range, a lower voltage stress across the power switches, and an absolute common ground. The operating principle, the voltage and current stresses on the power switches, the comparisons with the other converters, the small signal analysis, and the controller design are presented in this paper. Finally, a 300 W prototype with $U_{{\rm{high}}}= {240 \ \rm{V}}$ and $U_{{\rm{low}}}= {40\sim 120\ \rm{V}}$ is developed, and the experimental results validate the performance and the feasibility of the proposed converter. [ABSTRACT FROM PUBLISHER]

This paper proposes a family of novel flying capacitor transformerless inverters for single-phase photovoltaic (PV) systems. Each of the new topologies proposed is based on a flying capacitor principle and requires only four power switches and/or diodes, one capacitor, and a small filter at the output stage. A simple unipolar sinusoidal pulse width modulation technique is used to modulate the inverter to minimize the switching loss, output current ripple, and the filter requirements. In general, the main advantages of the new inverter topologies are: 1) the negative polarity of the PV is directly connected to the grid, and therefore, no leakage current; 2) reactive power compensation capability; and 3) the output ac voltage peak is equal to the input dc voltage (unlike neutral-point-clamped and derivative topologies, which requires twice the magnitude of the peak ac voltage). A complete description of the operating principle with modulation techniques, design guidelines, and comprehensive comparisons is presented to reveal the properties and limitations of each topology in detail. Finally, experimental results of 1-kVA prototypes are presented to prove the concept and theoretical analysis of the proposed inverter family for practical applications. [ABSTRACT FROM PUBLISHER]

DC microgrids are popular due to the integration of renewable energy sources such as solar photovoltaics and fuel cells. Owing to the low output voltage of these dc power generators, high efficient high gain dc–dc converters are in need to connect the dc microgrid. In this paper, a nonisolated high gain dc–dc converter is proposed without using the voltage multiplier cell and/or hybrid switched-capacitor technique. The proposed topology utilizes two nonisolated inductors that are connected in series/parallel during discharging/charging mode. The operation of switches with two different duty ratios is the main advantage of the converter to achieve high voltage gain without using extreme duty ratio. The steady-state analysis of the proposed converter using two different duty ratios is discussed in detail. In addition, a 100 W, 20/200 V prototype circuit of the high gain dc–dc converter is developed, and the performance is validated using experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, a single-phase multilevel ac/ac converter with reduced number of power semiconductor devices is proposed. For the simple case of a three-level converter, only three bidirectional switches and two capacitors are required. The proposed converter provides a highly sinusoidal and regulated output voltage with a simple topology. The efficiency is high because in each state of operation only one semiconductor conducts. The converter can be easily extended to any desired levels in the output voltage to even more reduce the output total harmonics distortion. Another advantage of the proposed converter is that by increasing the voltage levels, the stress on the switches will decrease. The proper performance of the proposed converter is confirmed through extensive simulation and experimental tests. [ABSTRACT FROM PUBLISHER]

This paper proposes a soft switching nonisolated dc/dc interleaved converter incorporating coupled inductors and switched capacitors for high step-up applications. The converter integrates the interleaved structure and winding-cross-coupled inductors technique to reduce current stress of semiconductor devices and diminish the input current ripple considerably. In addition, the interleaved converter has the automatic current sharing characteristic. The applied zero voltage transition cell provides soft switching in a wide range of load variations with a minimum number of elements. In this topology, all semiconductor devices are soft switched, having eliminated switching losses and alleviating the reverse recovery problem of the output diodes. In addition, the voltage stress across the switches is very low. The theoretical analysis and design procedure of the introduced topology are presented. Also, the proposed converter is compared to the latest similar soft switched high step-up converters. The accuracy of the theoretical analysis is validated by a 200-W prototype operating at 100 kHz. [ABSTRACT FROM PUBLISHER]

The asymmetrical modulation strategy is widely used in various types of three-level (TL) dc/dc converters, while the current imbalance among the power switches is one of the important issues. In this paper, a novel periodically swapping modulation (PSM) strategy is proposed for balancing the power switches’ currents in various types of TL dc/dc converters. In the proposed PSM strategy, the driving signals of the switch pairs are swapped periodically, which guarantees that the currents through the power switches are kept balanced in every two switching periods. Therefore, the proposed PSM strategy can effectively improve the reliability of the converter by balancing the power losses and thermal stresses among the power switches. The operation principle and performances of the proposed PSM strategy are analyzed in detail. Finally, the simulation and experimental results are presented to verify the proposed modulation strategy. [ABSTRACT FROM PUBLISHER]

This paper proposes a new bridge modular switched-capacitor-based ac–ac converter, which is intended to replace conventional transformers in commercial and residential applications, especially for microgrids. The main advantages of the proposed converter lie in high efficiency and power factor, bidirectional operation, and capacitor voltage self-balancing ability. Another distinct merit is its symmetric construction, with which the voltage ripple of charge/pump capacitors can be cancelled out, and the output voltage will be smooth with significant ripple reduction. It is also noteworthy that the symmetric construction ensures that the two symmetric parts can work independently under a simplified control strategy. In addition, the modular configuration contributes to convenient voltage extension. Compared with the reported flying-capacitor switched-capacitor ac–ac converter, the proposed converter requires fewer switches and capacitors per unit of voltage conversion, thus suffering lower voltage stress. To demonstrate the performance of the converter, a prototype with 600-W 220-Vrms high-side voltage, 55-Vrms low-side voltage, and a switching frequency of 100 kHz was designed and fabricated. The relevant experimental results are reported herein. The maximum and rated power efficiency obtained were 95.9% and 94.4%, respectively. [ABSTRACT FROM PUBLISHER]

In this paper, a new negative output (N/O) buck–boost converter, which can be applied for applications that need wide range of inverse voltage, is proposed. The steady-state, small-signal model and power losses of the proposed converter operating in a continuous conduction mode are analyzed. Comparisons among the traditional buck–boost converter, N/O hybrid buck–boost converter and N/O self-lift Luo converter are presented, and it is found that the proposed converter possesses a widest voltage conversion ratio in these four converters. Finally, a prototype is built, and the simulated waveforms from the PSIM software and the experimental results are presented for validation. [ABSTRACT FROM AUTHOR]

In order to reduce the cost and volume of small-medium power ac–dc light-emitting diode (LED) lighting systems, single-stage LED drivers are often used to drive LEDs with constant current. In this paper, a single-stage isolated high-power factor ac–dc LED driver is proposed and analyzed in detail, which is composed of a buck–boost power factor correction unit operating in discontinuous conduction mode and an isolated dc/dc unit with a voltage doubler rectifier, and the two units are integrated together by sharing the same power switch. Very high input power factor is achieved since the PFC unit operates with almost fixed duty ratio during half period of the utility line voltage. Since a voltage doubler rectifier is included in the isolated dc/dc unit, magnetic core size of the transformer and voltage stress of the secondary side diodes are reduced remarkably. First, the operating principle and performance of the LED driver are analyzed. Then, the main parameters are quantitatively calculated out in detail. Finally, a comparative analysis is presented and a 120 W experimental prototype with 1 A output current is built according to the calculated parameters and the experimental results are presented to verify the correctness of the theoretical analysis and parameter design. [ABSTRACT FROM PUBLISHER]

In this paper, a new structure for high step-up dc–dc converters is proposed. In the proposed structure, it is possible to extend the topology by increasing the number of active–passive inductor cells. High voltage gain with lower duty cycle, low-current and -voltage stresses on switches, small inductors, and small size of filter are the main advantages of the proposed structure. The proposed converter is analyzed in different operating modes. In order to design the components’ values of the proposed converter, the equations of output voltage ripple are calculated in each operating mode and a design procedure is proposed based on the aforementioned equations. Moreover, the losses and efficiency of the converter are calculated. In order to validate the correctness of calculations and analyses, the experimental results are given. [ABSTRACT FROM PUBLISHER]

A novel transformerless buck–boost dc–dc converter is proposed in this paper. The presented converter voltage gain is higher than that of the conventional boost, buck–boost, CUK, SEPIC, and ZETA converters, and high voltage can be obtained with a suitable duty cycle. In this converter, only one power switch is utilized. The voltage stress across the power switch is low. Hence, the low on-state resistance of the power switch can be selected to decrease conduction loss of the switch and improve efficiency. The presented converter has simple structure, therefore, the control of the proposed converter will be easy. The principle of operation and the mathematical analyses of the proposed converter are explained. The validity of the presented converter is verified by the experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents a multilevel step-up dc/dc converter for dc-grid-based offshore wind energy conversion applications. The main features of the proposed multilevel converter are as follows: 1) the voltage stress of the power devices can be reduced, making it suitable for high-voltage applications; 2) the boost inductor can be reduced significantly, leading to the outstanding dynamic performance; and 3) high-voltage gain can be obtained and thus is well-suited for high-gain applications. Theoretical analysis was carried out for a four-level step-up converter, based on which, the converter can be extended to any arbitrary number of levels. The proposed four-level converter was verified by a simulation and evaluated by comparing with a conventional multilevel dc/dc converter in terms of the component stress and power device count. The developed topology was implemented on a 2-kW prototype converter to evaluate its feasibility. [ABSTRACT FROM AUTHOR]

The five-phase coupled-inductor inverter is a newly proposed option for three-level five-phase inverter drives. This paper comprehensively analyzes the inverter including the coupled-inductor current, current stress on the dc-link capacitors, and a comparison of these performance aspects using three pulse width modulation (PWM) strategies. Mathematical derivations of the inverter currents and the associated current stress reveal that the current stress is not only influenced by the choice of modulation strategy, as in the neutral-point-clamped topology, but also by the value of coupled inductance; furthermore, the choice of the modulation strategy impacts the core loss of the coupled inductors. Three carrier-based PWM methods are considered: sinusoidal PWM (SPWM), and two methods with the common-mode voltage reduction (referred to as CMVR1 and CMVR2) for the five-phase coupled-inductor inverter. CMVR2 is shown to be the best solution if common-mode voltage reduction is required. The analysis demonstrates that SPWM performs better with respect to current stress and inverter losses, therefore is the preferable modulating strategy for the five-phase coupled-inductor inverter if common-mode voltage reduction is not required. The analysis is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]