Search

In photovoltaic systems, common-mode voltage (CMV) generates leakage current, which shortens the insulation lifespan and causes safety problems. As for neutral-point-clamped (NPC) inverters, zero CMV PWM (ZCMV PWM) can be implemented to eliminate leakage current, but unable to balance neutral-point (NP) voltage in dc side. This article presents a novel modulation technique for NPC PV inverter. The strategy contains ZCMV PWM and another two modulation modes which keeps CMV constant in one switching period, so as to eliminate leakage current. In order to balance NP voltage, NP current is adjusted by selection of optimal modulation mode and the leakage current is still well eliminated during the process of balancing NP voltage. Compared with conventional ZCMV PWM, the proposed scheme can remove both leakage current and NP voltage deviation. The output performance and limitations of the proposed method are also introduced in the paper. Experiments are provided to verify the validity of the proposed method. [ABSTRACT FROM AUTHOR]

DC shipboard power systems have been considered as a promising solution for stricter environmental regulations on ships due to their main benefits in fuel savings with variable speed engines and easy integration of energy storage systems. In order to employ the dc solution in the shipboard power systems, the dc power systems have to be protected from a system fault with protection selectivity to minimize impacts of the fault or to avoid other undesirable situations in the system. For low-voltage dc shipboard power systems, a three-level protection has been proposed: 1) fast action (first)—bus separation by solid-state dc bus-tie switch; 2) medium action (second)—feeder protection by high-speed fuse; and 3) slow action (third)—generator–rectifier fault controls. This paper proposes a new method by means of additional bus capacitance added in main dc buses to help reliable operation of the three-level protection. The principle of the proposed method is introduced and the sizing of the additional bus capacitance is addressed in this paper. With the modeling of the dc shipboard power systems, the analyses of voltage drops for the bus separation failure and fault clearing time for the feeder protection are carried out to verify the proposed method. The results show that the proposed method not only mitigates the voltage drop for the bus separation failure, but also achieves the selectivity and the sensitivity for the feeder protection. [ABSTRACT FROM AUTHOR]

This paper presents a 5-level inverter topology for open-end induction motor drives by using a single dc source. The open stator windings of the drive are supplied with a 3-level flying capacitor inverter from one end and capacitor-fed 2-level inverter from another end. The voltage ratio of the dc link to the capacitor in 2-level inverter is maintained at 4:1 ratio to generate five-level voltage output. The capacitor in 2-level inverter is balanced by the switching redundant vector combinations from both the inverters while the floating capacitors in the 3-level inverter are balanced by using redundant switching states. The proposed topology gives 5-level operation with less number of floating capacitors and power semiconductor switches compared to other existing topologies. Also, the balancing of the capacitors is independent of load power factor and modulation index. Further, the generalization of the proposed dual inverter scheme for any n-level inverter is also included in this paper. The experimental results and required analysis are also presented to validate the inverter scheme. [ABSTRACT FROM AUTHOR]

In this paper, a new modular and active snubber cell, easily applicable, and attractive for converters, especially have many switches proposed. This snubber cell is implemented on the single phase of a grid-connected three-phase T-type three-level inverter (T-3LI). In this new converter, the main switches turn-on under zero-voltage transition and turn-off under zero-voltage switching (ZVS). Also, auxiliary switches turn-on under zero-current switching and turn-off under ZVS. All snubber diodes operate under soft switching (SS). There are no additional current and voltage stresses on the main switches. During an SS operation, the switching energies are transferred to a dc voltage source. Then, these energies are processed to input with an independent dc–dc converter. Thus, all switching energies are recycled. In this paper, the principle operation and steady-state analysis of the modular and active snubber cell for a single-phase T-3LI are presented and experimental results, rated 1 kW and 100 kHz, are provided to verify theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper presents a unified second-stage LC filter applied in the three-state switching cell buck–boost converter, which provides current and voltage with low ripple and low noise. The unified second-stage filter promotes a reduction in the number of devices while maintaining the filtering performance of the converter, with second-stage LC filters at the input and at the output. Moreover, the unified filter, when associated with a three-state switching cell buck–boost converter, allows a size reduction of filter devices, especially for designs with duty cycle range around 1/2. Furthermore, the unified filter arrangement provides nondissipative clamping of switching devices and reduce the system order when compared to the converter with second-stage LC filters. In this paper, the static and dynamic characteristics of the proposed converter in continuous conduction mode (CCM) are reported. Experimental data were obtained from a laboratory prototype with an input range of 32 $\sim$ 72 V, constant output of 48 V, a load of 150 W, and switching frequency of 45 kHz. The measured efficiency for the rated load was 97% for maximum input voltage. A comparison of the size and performance of the proposed filter with the topology that uses second-stage LC filters at the input and at the output is also presented. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

A space vector modulation (SVM) technique of a dual-inverter system for an open-end winding motor drive is described in this paper, where one inverter has a battery power source and the other has an only capacitor across the dc bus. The SVM must be achieved to operate the motor with field-oriented control and simultaneously to control the capacitor voltage at a constant value by using redundant switching states of the dual-inverter system. The control of the capacitor voltage is carried out by selecting a charging or a discharging mode in each redundant switching state, taking the instantaneous motor power factor into account. In addition, it is also required to reduce the error voltage pulses, which are generated in output multilevel voltage waveforms during the dead time. The compensation method of the existing dead-time scheme and the improved SVM sequence to reduce the error voltage vectors are proposed in this paper. The proposed methods are examined through several experimental tests and are confirmed to generate superior output voltage waveforms from the viewpoint of the measured total harmonic distortion and dv/dt. [ABSTRACT FROM AUTHOR]

This paper presents a novel integrated-stage light-emitting diode (LED) driver based on Flyback and resonant converters. The Flyback converter realizes power factor correction in the discontinuous conduction mode. The resonant converter is operated as a dc–dc converter to support the LED loads. Moreover, the resonant converter can clearly decrease the drain–source voltage of the active switch and exhibits zero-voltage-switch characteristics. Therefore, a cost-effective MOSFET can be chosen as the main control component that can decrease the cost of the whole system. Compared to a single-active-switch converter (such as Class-E converter), the number of passive components in the resonant converter can be limited to four. Therefore, the power density of the system can be improved drastically. In this paper, a 100-W prototype is presented under the experimental condition to validate the proposed integrated-stage LED driver. [ABSTRACT FROM AUTHOR]

In this paper, a single-inductor dual-output (SIDO) dc–dc converter is proposed. The significant feature of the proposed converter is feeding a constant power load in low-voltage side (LVS) port, where even feeding a variable load at LVS does not have any cross regulation to high-voltage side port with the desired approximation. Magnificently, both merits are obtained in open-loop manner, which is an outstanding characteristic in comparison with that of the existed converters. In this paper, soft commutation and soft switching of switches and diodes are investigated along with the aforementioned main novelty. Moreover, detailed theoretical analyses of the proposed SIDO dc–dc converter in continuous conduction mode are presented besides the comparisons with some other structures. Finally, theoretical analyses are verified through a 1500 W experimental prototype results. [ABSTRACT FROM AUTHOR]

In this paper, a series-capacitor-based interleaving buck power factor correction (PFC) converter is proposed, the intermediate energy storage capacitance of which is operated at discontinuous capacitor voltage mode (DCVM), and automatic power factor (PF) correction for this converter is obtained. Moreover, the voltage across the series capacitor of the proposed PFC converter is clamped at the input voltage, and thus peak voltage stress existed in the traditional DCVM buck PFC could be relieved. By effectively regulating the charge/discharge time for the series capacitor, ultrahigh step-down conversion ratio of the proposed converter is achieved, the conversion ratio of which is independent of the duty cycle and only related to the switching frequency and circuit parameters. Therefore, high PF can be obtained due to very narrow deadtime of the input current. Meanwhile, the proposed PFC converter can realize the soft turn-on of part power switch and soft turn-off of part power diodes. In addition, comparing with the traditional discontinuous inductor current mode PFC, the input current of the proposed PFC converter is continuous so that the peak value and root-mean-square value of input current can be reduced. The operational principle, performance analysis, and parameter design principle are given in this paper. The analysis results show that the PF and total harmonic distortion are also independent of the duty cycle. Finally, a 220-Vac input, 60 W/15 V output experimental prototype is built to verify the validity of the theoretical analysis. [ABSTRACT FROM AUTHOR]

Reduced switch active phase converters (APC) are cost-effective solutions for running three-phase loads from single-phase grids. This paper proposes a novel auxiliary-capacitor-based APC (AC-APC) for this application. The combination of the topological location of the auxiliary capacitor and the control of the AC-APC reduces current stress on the semiconductor devices. In this paper, a selection criterion for the optimal auxiliary capacitor value is formulated to reduce the device currents in such a way that the overall efficiency is enhanced. This paper presents a comparative analysis of converter volt-ampere (VA) rating and device power loss for conventional H-bridge active front-end and inverter-based topology, APC, and AC-APC. To evaluate the efficacy of the proposed AC-APC, an experimental study is conducted on the APC and the AC-APC feeding a 3-hp three-phase induction motor. At a full load of $\text{2.5}\,\text{kW}$ and $\text{0.8 } \text{power factor}$ , the measured maximum efficiency of the AC-APC is $2\%$ higher than that of the APC. Analytical evaluation of converter currents and device power loss are in close agreement with experimental observations. [ABSTRACT FROM AUTHOR]

This paper proposes a capacitor voltage regulation method for the dual converter with a floating bridge for aerospace applications. This topology has previously been reported, but with a constrained voltage utilization factor due to the need for capacitor voltage regulations. In this paper, the effect of switching states on the voltage variation of capacitor is quantitatively modeled and an enhanced space vector modulation scheme with current feedback is proposed to achieve an active control of the floating capacitor voltages. This proposed method also allows further exploitation and utilization of converter voltage. The relationship between the allowed modulation index of dual converter and load power factor is obtained and expressed using a fitted polynomial equation. The advantages of the proposed method include boosted voltage utilization and superior performance in term of capacitor voltage balance. These advantages have been proven through simulation and experimental results on RL loads as well as with an open-end winding induction motor. The proposed modulation scheme can boost the converter voltage utilization by at least 10% while achieving full four-level operation. More importantly, the higher available voltage allows extending the constant torque region of the motor, the further beginning of field weakening operation could be postponed. [ABSTRACT FROM AUTHOR]

Motors and inverters are increasingly being used in vehicles. As more vehicle components are being adopted, requirement for safety and installation space are increasing. Growing attention is being paid to the use of six-phase permanent magnet synchronous motors (PMSMs) and their parallel control by two inverters, because of their reduced size and enhanced safety. This paper proposes a pulsewidth modulation (PWM) control algorithm for a six-phase PMSM. In low-voltage vehicle components such as electric power steering, the current is usually acquired with resistors placed under the low-side switching devices. In the proposed control algorithm, the neutral voltage of the two inverters is shifted to either a lower or higher voltage within a certain range to allow for the signal conditioning time delay after the switching device turns on or off, and the time taken for the phase current to rise or settle. The paper proposes a novel PWM control algorithm that ensures that the on-time of the low-side switching devices satisfies the restriction on current sensing with resistors and reduces the current in the capacitor at the same time. The work contributes to reducing the current in a practical configuration involving low-voltage vehicle components. [ABSTRACT FROM AUTHOR]

A trinary multilevel converter uses a few heterogeneous H-bridge submodules (SMs) to synthesize an output voltage with multiple levels. Two major limitations of this converter are that it needs multiple dc sources and it cannot operate under pulsewidth modulation (PWM). This paper addresses these limitations by adding a low-voltage H-bridge SM to this converter and proposing a new switching algorithm. The resulting PWM-based asymmetric cascaded H-bridge converter uses only one dc source and synthesizes a high-quality output voltage. This improved converter can be a potential choice for real and reactive power support in power system applications. This paper also proposes methods for stability analysis and design of this converter. Experimental case studies evaluate the performance of the proposed converter for both standalone and grid-connected modes of operation. [ABSTRACT FROM AUTHOR]

This paper proposes a new developed switched-capacitor converter to achieve high-voltage pulses with adjustable voltage level and frequency. The proposed topology generates repetitive high-voltage pulses by using low-voltage power supply with reduced number of components, including power semiconductors and capacitor. Therefore, a converter based on switched-capacitor units with high voltage gain and high efficiency can be achieved. Operation principles and design steps of the converter as well as comparative study with conventional converters are described in this paper. Finally, simulation and experimental results of a two-stage structure of the proposed circuit validate the operation principles and features of this topology. [ABSTRACT FROM AUTHOR]

This paper develops a modulation based fault-tolerant (FT) strategy for restoring the operation of three-phase modular multilevel converters (MMCs) with faulty switches. This FT strategy is based on a proposed modified space vector modulation (SVM) technique that generates balanced line-to-line (line) voltages even in the case of a fault occurrence. In the postfault operation, the proposed strategy is able to restore the fundamental amplitude of the line to the neutral (load) voltages to that of the normal operation condition with a slightly increased voltage stress over the switches in the faulty phase. In this paper, first a brief background about MMCs and SVM technique is provided. Then, the proposed FT strategy and the modified SVM technique are presented. Finally, several simulation and experimental results are provided to validate operation of the proposed strategy. [ABSTRACT FROM AUTHOR]

This paper presents two capacitor voltage balancing (CVB) strategies for modular multilevel converter (MMC) applications. Both balancing schemes are based on model predictive control and are designed to efficiently solve a constrained optimal control problem, where the predicted capacitor voltage errors are included in the cost function with the demanded output voltage of a cluster being forced through an equality constraint. The first method proposed in this paper computes specific modulation indexes for each module using the explicit solution of a relaxed version of the original optimization problem. The second approach proposed in this paper reduces the complexity of the original problem by linearizing the objective function and using an optimal sorting network based on a greedy algorithm to solve this approximation. Considering the structures of both solution approaches, they are integrated into modulation schemes based on phase-shifted and level-shifted pulsewidth modulation algorithms, respectively. Experimental results obtained from a nine-cell single-phase MMC prototype demonstrate the good performance achieved with the proposed methodologies, as well as the implementation simplicity offered by the proposed CVB algorithms. [ABSTRACT FROM AUTHOR]

This paper proposes a new dc–ac converter with a reduced number of semiconductor switches and gate drive and control circuit components. A salient feature of this inverter is its pure sinusoidal line-to-line voltages with no need for output filter. Also, the proposed inverter improves the voltage utilization factor of the input dc supply compared to the four-switch three-phase inverter (first best topology in the literature from the number of switches point of view) and standard six-switch inverter with sine pulsewidth modulation. The proposed inverter is capable of operating with a wide range of output voltages from zero to the full value of the dc input voltage by appropriately altering the instantaneous duty cycle. A three-phase universal inverter with only three power switch has been proposed in this paper for the first time ever, to our knowledge. For the purpose of providing a good compromise between fast transient response and stability, a model predictive controller is proposed. All the design expressions have been derived. A comparison with other dc–ac converters is given to show the merits of the proposed converter. Finally, satisfactory circuit operation is confirmed by experimental results from a laboratory prototype. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high step-down dc–dc converter with ultrahigh step-down conversion ratio is proposed. Advantages of the proposed converter are high step-down ratio, extended duty cycle, reduced switching losses by a converter operation under zero-voltage switching (ZVS) conditions, reduced reverse reco-very losses of diodes by achieved zero-current switching turn-off condition, and reduced voltage spikes by the inherent active-clamping structure of the converter. In this converter, series capacitors and coupled inductors have been used in power path to achieve the low voltage gain and extended duty cycle. By the inherent active-clamping structure of the proposed converter, the leakage inductance energy is totally recovered in the output; therefore, the high voltage spike across the semiconductor devices is suppressed. The switches of the proposed converter can operate under ZVS conditions, which cause reduced switching losses and improved efficiency. In this paper, the converter operating modes are discussed, and a prototype circuit is implemented. Experimental results are presented to verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

This paper analyzes the combination in a cascaded H-bridge multilevel inverter (CHBI) based on transformers with the different turn ratios for increasing the voltage level and proposes the switching method for achieving the output voltage distribution among H-bridge cells (HBCs). The transformers used in this paper are connected to the output of the respective HBCs, and the secondary sides of all the transformers are connected in series for generating the final output voltage. Only one of the transformers, in particular, has a different turn ratio for increasing the output voltage level. In this paper, the possible turn ratio of the special transformer with a different turn ratio is discussed in detail, and a switching method based on the level-shifted switching method for the topology used in this paper is proposed. To verify the effectiveness of the proposed method, a three-phase 21-level CHBI is experimentally tested. [ABSTRACT FROM PUBLISHER]

This paper presents a new multilevel converter topology based on a variable or multilevel dc-link stage. This stage is shared by all inverter output phases, thus increasing the number of output voltage levels while reducing the overall number of active devices compared to traditional topologies; therefore, it is called a reduced multilevel converter (RMC). The converter is not capable of reducing the blocking voltage of the devices; hence, unlike other multilevel converters aimed at medium-voltage applications, this converter is interesting for low-voltage- and high-power-quality-demanding applications such as photovoltaic inverters, wind energy conversion systems, and uninterruptible power supplies. The main novelty behind the proposed concept is the basic dc cell used to generate the variable dc-link voltage, which includes a controlled path through the floating capacitors to provide the necessary degree of control to enable a shared multilevel dc link for all the output phases of the converter. The dc cells are connected in a multicell structure to increase the number of levels of the converter. A five-level version of the RMC topology is briefly compared to other five-level converters such as the five-level active neutral-point-clamped converter and the five-level flying capacitor converter. This paper presents the structure of the new topology with its operating principle, switching states, main characteristics, and experimental validation using finite-control-set model-predictive control. [ABSTRACT FROM PUBLISHER]

A new isolated single-stage soft-switching power-factor-correction (S4 PFC) driver for supplying light-emitting diodes (LEDs) is introduced in this paper. In the proposed LED driver, the switches voltage stress and also the dc-bus voltage is limited to the peak of the line voltage. Hence, low voltage rated mosfets and diodes can be used. The efficiency is improved because the switches are turned on under zero current switching (ZCS) condition and turned off under zero voltage zero current switching (ZVZCS) condition. Also, no current feedback is required since the converter provides an output current independent of output voltage. In this paper, operating principle of the proposed LED driver is presented and design considerations are discussed. To verify the theoretical analysis, a laboratory prototype of the proposed converter for supplying a 50 W/70 V LED module from 220 Vrms/50 Hz ac mains is implemented, and the experimental results are presented. Since current feedback is not used, dimming property and operation for universal voltage range is not achievable. [ABSTRACT FROM PUBLISHER]

In this paper, new half-bridge and full-bridge topologies for a switched-boost inverter are proposed. These topologies have a high boost factor in comparison with conventional types. In addition, the proposed topologies have continuous input current and can generate zero-voltage level in output. In this paper, the operation of the proposed inverters in different operating modes is analyzed. Then, the values of inductors and capacitors are designed. Moreover, the used switching pattern and its logical diagram are introduced. A comprehensive comparison between the proposed and conventional topologies in terms of the boost factor, the number of elements, and the efficiency shows the good features of the proposed inverters. Finally, to verify correct operation of the proposed topologies and derived equations, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

The development of a high static gain dc–dc converter with the integration of the voltage multiplier cell and the coupled inductors operating with soft switching is presented in this paper. The use of coupled inductors and voltage multiplier techniques allow the operation with low switch voltage and low conduction losses. The switch turn-on commutation occurs with zero current switching due to the presence of the coupled-inductor leakage inductance. The leakage inductance also reduces the reverse recovery current of all diodes. The zero voltage switching at the power switch turn-off is obtained with the inclusion of only a diode and a snubber capacitor per phase, without the use of auxiliary switches. The soft-switching range is independent of the load and is maintained even with a light load. The theoretical analysis, design procedure, and experimental results are presented in this paper. A two-phase boost converter with one voltage multiplier and coupling inductors was built with an input voltage $V_{{\text{in}}}= { \text{24 V}}, output voltage Vo= { \text{432 V}}, and output power Po= { \text{400 W}}. The efficiency obtained is equal to 94.55% at the nominal power. [ABSTRACT FROM PUBLISHER]

In this paper, a nonisolated dc–dc converter with high voltage gain is presented. Three diodes, three capacitors, an inductor, and a coupled inductor are employed in the presented converter. Since the inductor is connected to the input, the low input current ripple is achieved, which is important for tracking maximum power point of photovoltaic panels. The voltage stress across switch S is clamped by diode D 1 and capacitor C1. Therefore, a main switch with low on-resistance RDS (on) can be employed to reduce the conduction loss. Besides, the main switch is turned on under zero current. This reduces the switching loss. The steady-state analysis of the proposed converter is discussed in this paper. Finally, the proposed converter prototype circuit is implemented to justify the validity of the analysis. [ABSTRACT FROM PUBLISHER]

This paper presents three unidirectional step-up ac–dc converter topologies with voltage multiplication on their outputs. The first topology is the hybrid boost rectifier and the other two are novel bridgeless structures, all based on the integration of boost rectifier and the ladder switched-capacitor (SC) cell. The new hybrid structures provide high voltage gain with low voltage stress across the switches, high-power factor, and output voltage regulation. This paper presents the principle of operation, steady-state and dynamic analysis, design methodology, and experimental verification. A different approach is also presented for the design methodology of the SC cell and for the analysis of its influence on the dynamic model. Three 1000-W prototypes with a 220-V input voltage, 800-V output voltage, and 100-kHz switching frequency were designed to corroborate the theoretical study. The best efficiency was 97.1$\%$ in the proposed bridgeless versions and the voltage stress across the switches stands around 400 V. Furthermore, a comparison between the proposed structures and previous topologies is also presented. [ABSTRACT FROM PUBLISHER]

This paper proposes an analytical design procedure for the LLCL and the LCCL filters for grid integration of high-power voltage-source converters. The low switching frequency and stringent limits on grid-injected harmonics in high-power applications lead to large smoothing filters. In order to reduce the size and weight, high-order filters are already proposed and wise design procedures with the main goal of minimizing the overall filter size are being suggested. In this paper, the parameters of the LLCL and the LCCL filters are designed in the per-unit system to satisfy the requirements on the injected grid current and at the same time minimize the overall filter size through minimizing the total energy stored in the filter components. The experimental results of a downscaled laboratory prototype with a low switching frequency prove the effectiveness of the proposed design procedure. [ABSTRACT FROM PUBLISHER]

This paper proposes a wide-range zero-voltage-switching (ZVS) active-clamped current-fed push–pull converter for fuel cell application. The presented converter achieves ZVS for all of the primary switches and ZCS for secondary diodes from rated load to 10% full load over the wide input voltage variation, improving the overall efficiency. The ZVS of switches is realized by the energy stored in the transformer leakage inductance aided by the secondary parallel inductor. An additional active clamping circuit suppresses the voltage spike as well as assists in realizing ZVS of switches. Low-voltage-rated switches with low on-state resistance can be used. Moreover, the voltage-doubler rectifier is adopted to release the reverse-recovery problem of rectifier diodes and reduce turns ratio of the high-frequency transformer. Detailed steady-state operation, analysis, design, control, comparative study, and experimental results are discussed in depth in this paper. Finally, a 200-W prototype has been built in the laboratory to verify the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, two topologies are presented for the enhanced-boost quasi-Z-source inverters (qZSI), namely continuous input current configuration and discontinuous input current configuration of enhanced-boost qZSI with two-switched impedance networks. Similar to enhanced-boost impedance-source inverters (ZSIs), these proposed inverter topologies possess very high boost voltage inversion at low shoot-through duty ratio and high modulation index to provide an improved quality output voltage. Compared to enhanced-boost ZSIs with two-switched Z-source impedance networks, these proposed inverter topologies share common ground with source and bridge inverter, overcome the starting inrush problem, and draw continuous input current and the lower voltage across the capacitors. Moreover, the input ripple current is negligible. This paper presents the operating principles and analysis of continuous input current configuration enhanced-boost qZSI with two-switched impedance networks and compares with ZSI, switched inductor ZSI, DA/CA-qZSI, and enhanced-boost ZSIs. The theoretical analysis is done and is validated through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes a family of soft-switching bidirectional converters. In many applications, the bidirectional converters operate over a wide range of duty cycle and load variations. In the proposed converters, in order to extend the zero-voltage switching operation range, two supplemental voltage sources utilizing passive components are implemented in the auxiliary circuit. By using this method, the soft-switching features are ensured for an extensive range of the converter duty cycles. This is achieved independent of the output power value or the converter operation mode, and so, soft switching is ensured within the entire converter operating region. In these converters, all semiconductors components are soft switched, and the auxiliary circuit does not contribute to the complexity of the control circuit. Also, no extra voltage stress exists on the main switches and the voltage stress on the auxiliary switches is lower than the main switches voltage stress. In this paper, the proposed bidirectional buck/boost converter is analyzed and to confirm the feasibility of the proposed method, experimental results of a 150-W prototype converter are presented. [ABSTRACT FROM PUBLISHER]

In this paper, a novel current fed hybrid dual active bridge dc–dc converter is proposed, which is suitable for a low-voltage fuel cell power conditioning system. The high-frequency input current ripple can be reduced to minimum because the input side switches are always switched at 50% duty cycles in spite of the fuel cell voltage and the load variation. Notch filter is used in the voltage feedback path to reduce the low-frequency input current ripple when interfaced with a single-phase inverter load. All of the power devices can achieve zero voltage switching by the proposed control strategy. The mode analysis, the operation principle, zero-voltage switching (ZVS) conditions, and parameter design are given in this paper. A 1 kW prototype has been fabricated to verify the effectiveness of the proposed converter and control strategy. [ABSTRACT FROM PUBLISHER]

This paper deals with a hybrid fault-tolerant converter topology. It is performed through the connection of a classical three-phase three-level neutral-point-clamped (3L-NPC) converter with a fourth three-level flying capacitor (3L-FC) leg. The 3L-FC leg actively balances the 3L-NPC neutral-point voltage. For normal operation mode, this paper proposes a mathematical design of the filter needed to connect these two different topologies. Experimentally, and thanks to the already existing decoupling capacitors of the 3L-NPC converter, this filter requires the addition of only one low size inductance. When one fault of the power switch of the 3L-NPC occurs, this paper proposes a hardware reconfiguration technique based on only two fuses and one thyristor per leg allows a safe postfault operation recovery. This is achieved thanks to a simple fault-detection method and a new technique that combines fault leg isolation and corresponding phase postfault connection to the neutral point. Also, a dedicated field-programmable gate array (FPGA)-based control of the reconfigured converter is synthetized to ensure power system availability under fault operation mode. The converter fault-tolerant capabilities are addressed through simulation results and original overall experimental validations of the fault detection and isolation and the postfault operation steps, carried out on a 15-kW prototype converter. [ABSTRACT FROM AUTHOR]

Resonant modular multilevel converters (RMMCs) have been proposed for high-voltage dc–dc applications. Using different modulation strategies, RMMC operates in different modes and achieves flexible step ratio. To provide a comprehensive study of RMMCs, this paper presents the modulation method achieving a wide range of step ratio with the ability of inherent-balancing. The conditions for guaranteeing the inherent-balancing ability are provided. The operation principle and performance of the RMMC are presented in this paper, which have been explored in a case study. The experimental results are obtained from a bench-scale setup, which have verified the theoretical analysis. [ABSTRACT FROM PUBLISHER]

Modular multilevel converter (MMC) has been one of the most popular candidates in high-voltage applications. However, reliability is a critical issue due to a large number of power switching devices and capacitors applied in the MMC. To improve the reliability of the MMC, a fast and reliable diagnosis strategy for the open-circuit fault is proposed in this paper, where submodule voltage sensors are relocated to the upper switching device. Furthermore, a voltage observer based on the submodule voltage sensor is established to monitor the capacitor and realize the power control of the MMC under normal operation. A Boolean logic operation based fault indicator is put forward based on the relationship of the operation state and binaried output of voltage sensors, which could detect and locate the open-circuit faults of the MMC very fast. The ratio of the increment of the observed and measured capacitor voltage during the period of positive arm current is applied to monitor the capacitor. The effectiveness of the proposed fault diagnosis strategy and the capacitor monitoring strategy is verified by the experiment results. [ABSTRACT FROM AUTHOR]

This paper introduces the bridgeless triple-mode resonant ac–dc converter and presents its dynamic model and control technique. The proposed converter operates in triple mode: discontinuous-conduction mode (DCM), continuous-conduction mode (CCM), and missing resonance mode (MRM). It has the advantages of small number of required components, medium power capacity, and high efficiency, but it is difficult to control because DCM, CCM, and MRM have their own dynamic characteristics. To solve this control problem, the mode boundaries are first identified and, corresponding to each mode, the dynamic model is developed to design the controller. In each mode, we propose to add a repetitive controller (RC) with a phase-lead compensator to the conventional duty ratio plus feedback controller. The RC is used to suppress the deterministic periodic disturbances and the phase-lead compensator is used to compensate for the incurred phase lag. A 1-kW digitally controlled converter prototype is built and used to demonstrate the validity of the proposed modeling and control approach. [ABSTRACT FROM AUTHOR]

A soft-switched nonisolated high step-up dc–dc converter based on the quasi-impedance-source structure is presented in this paper. In the proposed converter, a technique similar to the synchronous rectifier is applied such that the diode of the impedance network is replaced with an active switch. In this way, not only is conduction loss associated with the diode reduced but also zero-voltage-switching characteristics for power switches are provided. Also, output diodes of the proposed converter are switched under zero-voltage-zero-current-switching condition which extremely reduces their switching and reverse-recovery losses. It is shown that by correct design of the components, soft-switching performance is retained for all the semiconductor devices over the entire range of output load. All these factors together with simplicity of the proposed structure result in high efficiency over a wide range of output power. Moreover, the proposed converter benefits from continuous input current and a shared ground between input and output. Operating principles of the proposed converter along with its steady-state analysis are presented. Also, experimental results obtained from a laboratory prototype for 48 to 350 V voltage conversion and 100 W nominal power are provided to validate the feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

Applying series configuration of the insulated gate bipolar transistors (IGBTs) to the pulsed power supplies offers unique features such as compactness and long life time. In the high-voltage pulsed power supplies, a large number of the IGBTs are required to be serially connected. Hence, the safe operating condition provision for the series IGBTs is an important and crucial issue. The effect of the voltage unbalancing factors becomes remarkable when the number of switches in the series structure increases. There are passive and active methods to balance the voltage of the series IGBTs. In both of these methods, an amount of power must be dissipated to remove the effect of the voltage unbalancing factors. Consequently, the power loss is considerable when a large number of series devices are necessary. This paper proposes an effective power recovery system that recovers the power associated with the series stacking of the IGBTs. Using this proposal, the efficiency of the resulted series switch enhances considerably. The power recovery system can be implemented easily for any number of series IGBTs. It consists of a simple dc–dc converter and several interconnection diodes for power recovery procedure. Proper performance of the proposed structure is evaluated by the aid of simulations and experiments. [ABSTRACT FROM AUTHOR]

This paper proposes an effective sliding mode controller (SMC) for a grid-connected 7-level packed U-cell (PUC7) inverter. The aim is to design a simple controller that deals effectively with the complex control problem of the PUC7 inverter (multiobjective control problem). The selection of the control actions is achieved according to the system state error at every sampling time, regardless of the previous values, which makes the control technique model-independent. The control algorithm evaluates online two cost functions (one for each state error), which are derived on the basis of sliding mode theory, and it selects the optimal control input in order to satisfy the reaching conditions of the two cost functions. Compared with the existing solutions, the proposed SMC technique ensures lower average switching frequency by tuning the hysteresis bandwidth of the capacitor-voltage error. The fast implementation, needless of gains tuning, and simple design procedure are the main features of the proposed algorithm. Simulation and experimental results are presented to prove the effectiveness of the proposed technique in controlling the PUC7 inverter with high dynamic performance and robustness against disturbances and parameters mismatch. [ABSTRACT FROM AUTHOR]

This paper introduces a novel single-phase buck–boost noninverting variable-frequency ac–ac converter that offers higher efficiency compared to the competitors. This converter utilizes a lower number of semiconductors. A simple and flexible switching strategy is also proposed, which generates the desired output waveform avoiding unnecessary high-frequency switching operation of semiconductor devices. A high reliable operation due to the elimination of the input source shoot-through risk, an inherent commutation capability that mitigates the voltage spikes across the semiconductors, a lower semiconductors rating requirement, an improved input current waveform quality, and a smaller required input filter inductor are the main advantages of the proposed converter. Thus, the proposed converter can be successfully applied to many industrial applications such as medium-frequency transformer isolation for traction and wind turbine converters, ac–dc high-voltage conversion based on Cockcroft–Walton circuit and induction heating systems. The theoretical achievements and claims are all confirmed through extensive experimental tests on a 200-W laboratory setup. [ABSTRACT FROM AUTHOR]

This paper proposes a new multilevel inverter (MLI) topology that utilizes trinary sequence for the dc sources. It gives maximum output voltage level with minimum dc source and switch count when compared to other sequences, such as symmetric, natural, binary, and quasi-linear. This is due to the fact that the trinary sequence generates of all additive and subtractive combinations of input dc levels in the output voltage waveform. The concept is implemented on a 9-level asymmetric MLI using only four active devices. Multicarrier unipolar pulsewidth modulation technique is adopted to create the switching pulses. Theoretical calculation of total harmonic distortion in both voltage and current waveforms has been performed using asymptotic time domain formula. These values are compared with simulation and experimental values for different modulation indices. Power loss calculation for proposed topology is discussed with appropriate mathematical equations. [ABSTRACT FROM AUTHOR]

In this paper, eight ultrahigh-voltage gain dc–dc converters are proposed. These sets of converters are derived by the association of boost cells, coupled inductor, voltage multiplier, switched capacitors, and LC filter cells. The nonpulsating input and output converters are evaluated in terms of: principle of operation, voltage gain, voltage and current stress, estimated power losses, and efficiency. Following full analysis prototypes built in the laboratory show experimental results verifying the theoretical analysis. [ABSTRACT FROM AUTHOR]

Multilevel inverters (MLI) with reduced components are becoming popular to achieve higher voltage levels with lower cost and complexities of the circuit. Most of the reduced switch MLIs use a large number of isolated voltage sources that have a large total standing voltage (TSV) and higher losses. Moreover, many reduced component MLIs have been developed to reduce the number of switches only and have not utilized the dc-link voltages properly. Thus, an inverter needs to be designed in which the number of dc sources is also small and utilized fully. In this paper, a novel single-phase, multicell MLI configuration is presented that can generate a maximum number of output voltage levels using a minimum number of switches and dc sources. Two optimal configurations of the proposed MLI are proposed based on the minimum requirements of components with the optimum voltage stress of the highest rated switches. Moreover, the TSV of the proposed optimal MLI also becomes low. A generalized multicell optimum MLI is presented and the number of components, voltage stress of all the switches, and the TSV of the proposed as well as the other inverters also determined by the generalized expressions for comparison purpose. The prototype of a specimen 15-level inverter and the optimal 75-level inverter cell is further developed and implemented using DS 1103 in the laboratory to show the effectiveness of the proposed configuration. The experimental results corresponding to the different modulation indices are presented here for the verification of the simulation results. [ABSTRACT FROM AUTHOR]

In this paper, closed-loop control and boundary condition for continuous conduction mode and discontinuous conduction mode of nonisolated inverting N× multilevel boost converter (MBC) are articulated. Inverting N× MBC combines the features of classical boost converter and voltage multiplier to attain inverting N times higher voltage. Consequently, the inverting N× MBC provides a viable solution for high-voltage step-up photovoltaic applications with low voltage rating reactive components and semiconductor devices. The control strategy with saturation limiter is employed to achieve highly stable voltage. The modes of operation, benefits of inverting N× MBC, and key factors for the selection of semiconductor devices and sizing of the reactive components are discussed. Additionally, the effects of reactive components and semiconductor devices on the output voltage are examined. Experimental results of the developed circuit are presented to validate the design of converter, and effectiveness and robustness of the implemented control algorithm for different input and output side perturbations. [ABSTRACT FROM AUTHOR]

This paper presents a novel fault-tolerant method for active–neutral-point-clamped (ANPC) inverter using a modified carrier-based pulsewidth modulation. At a fault event, the ANPC inverter is divided into subinverters, and the modulating signal is modified to two modulating signals. The modified modulating signals are used to control the subinverters and allow continuous operation of the three-level ANPC inverter during faulty conditions even up to four open-switch faults per phase. This technique provides the fault-tolerant capability of the ANPC inverter without the need to add any additional phase legs or complex control strategies. Furthermore, the proposed technique ensures the voltage balancing of the dc-link capacitors. The performance of the proposed fault-tolerant technique is verified through simulation studies in MATLAB/Simulink under different faulty conditions. The feasibility of the proposed technique is also verified experimentally. [ABSTRACT FROM AUTHOR]

In this paper, a voltage sensorless controller is developed for a two-switch single-phase rectifier that involves power factor correction and active pulsating power buffering without electrolytic capacitors. While a two-switch rectifier normally requires four sensed signals for control, only one current sensor is required in this proposal, thereby offering advantages such as low cost, high compactness, isolation between control and power circuits, and improved reliability. While the basic operating principle follows that of a conventional voltage sensorless controller for single-switch converters, several critical design considerations are the key to the success of the implementation which is explained in detail. The feasibilities of the controller are experimentally testified with a 100-W rectifier prototype regarding both steady state and dynamic performance. [ABSTRACT FROM AUTHOR]

In this paper, a new transformerless buck–boost converter based on a ZETA converter is introduced. The proposed converter has the ZETA converter advantages, such as buck–boost capability, input-to-output dc insulation, and continuous output current. The suggested converter voltage gain is higher than the classic ZETA converter. In the presented converter, only one main switch is utilized. The proposed converter offers low voltage stress of the switch; therefore, the low on-state resistance of the main switch can be selected to decrease the losses of the switch. The presented converter topology is simple; hence, the control of the converter is simple. The converter has the continuous output current. The mathematical analyses of the presented converter are given. The experimental results confirm the correctness of the analysis. [ABSTRACT FROM AUTHOR]

Circuit analysis and design criteria of a two-phase bidirectional converter with high voltage gain are presented in this paper. The operating principle of the forward or reverse mode is similar to that of the conventional buck or boost converter. Compared with the conventional converter, the switch stresses can be reduced significantly depending on the operating region of the voltage ratio in the two-phase converter. The power losses can also be reduced due to the use of low-voltage rating switches. The derivate converters are discussed to demonstrate the advantages of the proposed topology. A 200 W/1 MHz two-phase prototype converter with gallium nitride (GaN) devices is built and tested to verify the feasibility. [ABSTRACT FROM AUTHOR]

In this paper, the design methodology of switched-tank converter (STC) is presented. The power loss breakdown analysis is conducted to point out the directions and paths for components optimization. It is revealed that the switching device conduction loss, printed circuit board (PCB) loss, and inductor loss become significant when output power is >150 W. Power loss of four switches is calculated and compared for switching device selection. The resonant capacitor is carefully designed to meet both current stress and ripple requirements. On the other hand, optimal design of the resonant inductors and PCB layout are fully investigated. The core loss model is provided, and different core materials are compared to minimize the core loss. Besides, a fine-tuned inductor winding structure is designed to achieve the lowest winding loss. Furthermore, PCB layout is optimized to get short loop length for each operation state. In addition to the hardware level optimization, an improved control method is proposed, in which the conduction time of switching devices is tuned to mitigate the circulating power. To verify the optimization work, a prototype of STC is built and tested. The experimental results indicate that a state-of-the-art performance of 98.71% efficiency and a 1000 W/in3 high power density is achieved. [ABSTRACT FROM AUTHOR]

For an LLC converter, it is difficult to realize the wide output range with conventional pulse frequency modulation control because of the limited operating frequency. This paper proposes a new hybrid control method. The proposed strategy combines the burst-mode control and phase-shift control methods for the LLC converter. The burst-mode control can regulate the output voltage from zero to its maximum value, and the phase-shift control can reduce the increased resonant current during burst-on time. By using this method, the wide output voltage range is realized with the low resonant current during burst-on time and zero-voltage switch (ZVS) for all switches. The reliability and efficiency of the converter can be improved accordingly. The burst duty ratio is regulated by the reference output voltage, and the phase-shift angle is derived when realizing ZVS for lagging-leg switches. Moreover, the resonant parameters and the maximum phase-shift angle are optimized under the constraints of current stress and ZVS condition. This method is easy to be implemented in a low-cost microcontroller because high-frequency real-time calculations are not necessary. A 1.5-kW prototype is built to verify the feasibility and validity of the proposed control method. [ABSTRACT FROM AUTHOR]