Search

This paper presents a novel model predictive control (MPC) for the T-type single-phase three-level inverters. The cumbersome procedure in tuning of weighting factors is eliminated so that the implementation of the proposed MPC becomes easy. The constant switching frequency is achieved during the control implementation in order to facilitate the filter design. In order to optimize the distribution of the output current harmonics, multiple voltage vectors are employed in each control cycle with their application times setting inversely proportion to the respective cost function. The redundant small voltage vectors are utilized to balance the neutral point voltage of the inverter by directly regulating the upper and lower dc-link capacitors voltages. Finally, the proposed MPC algorithm is experimentally evaluated and compared with other two unfixed switching frequency MPC algorithms in terms of the steady state, transient performance, and parameter sensitivity. [ABSTRACT FROM AUTHOR]

This paper presents a new reconfiguration module for asymmetrical multilevel inverters in which the capacitors are used as the dc links to create the levels for staircase waveforms. This configuration of the multilevel converter makes a reduction in dc sources. On the other hand, it is possible to generate 13 levels with lower dc sources. The proposed module of the multilevel inverter generates 13 levels with two unequal dc sources (2VDC and 1VDC). It also involves two chargeable capacitors and 14 semiconductor switches. The capacitors are self-charging without any extra circuit. The lower number of components makes it desirable to be used in wide range of applications. The module is schematized as two back-to-back T-type inverters and some other switches around it. Also, it can be connected as a cascade modular which leads to a modular topology with more voltage levels at higher voltages. The proposed module makes the inherent creation of the negative voltage levels without any additional circuit (such as H-bridge circuit). Nearest level control switching modulation scheme is applied to achieve high-quality sinusoidal output voltage. Simulations are executed in MATLAB/Simulink and a prototype is implemented in the power electronics laboratory in which the simulation and experimental results show a good performance. [ABSTRACT FROM AUTHOR]

Multiphase variable-speed drives and generation systems (systems with more than three phases) have become one of the mainstream research areas during the last decade. The main driving forces are the specific applications, predominantly related to the green agenda, such as electric and hybrid electric vehicles (EVs), locomotive traction, ship propulsion, “more-electric” aircraft, remote offshore wind farms for electric energy generation, and general high-power industrial applications. As a result, produced body of significant work is substantial, making it impossible to review all the major developments in a single paper. This paper therefore surveys the recent progress in two specific areas associated with multiphase systems, namely power electronic supply control and innovative ways of using the additional degrees of freedom in multiphase machines for various nontraditional purposes. [ABSTRACT FROM AUTHOR]

A new approach for modulation of an 11-level cascade multilevel inverter using selective harmonic elimination is presented in this paper. The dc sources feeding the multilevel inverter are considered to be varying in time, and the switching angles are adapted to the dc source variation. This method uses genetic algorithms to obtain switching angles offline for different dc source values. Then, artificial neural networks are used to determine the switching angles that correspond to the real-time values of the dc sources for each phase. This implies that each one of the dc sources of this topology can have different values at any time, but the output fundamental voltage will stay constant and the harmonic content will still meet the specifications. The modulating switching angles are updated at each cycle of the output fundamental voltage. This paper gives details on the method in addition to simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents a new family of hybrid Z-source boost dc–dc converters intended for photovoltaic applications, where the high step-up dc–dc converters are demanded to boost the low-source voltages to a predefined grid voltage. Because the boost capabilities of the traditional Z-source networks are limited, the proposed converters are composed of combine traditional Z-source networks in different ways to enhance the boost abilities of the traditional Z-source networks. The new version of the proposed Z-source converters is termed as hybrid Z-source boost dc–dc converters to satisfy the traditional benefits of Z-source networks with stronger voltage boost abilities which can also be applied to dc–ac, ac–ac, and ac–dc power conversions. The performances of the proposed converters are compared with other Z-source networks behaviors. The simulation and experimental results of the proposed converters are validated at different operating conditions. [ABSTRACT FROM PUBLISHER]

Compensation of nonlinear effects generated by dead-time and semiconductors voltage drop has been widely studied in the literature about two-level converters. This paper takes a closer look at those analyses for multilevel converters, specifically for a cascaded H-bridge (CHB) converter modulated with phase-shifted pulse width modulation. The interaction between the cells is analyzed for a generic $n$ -cell converter, from which a general expression for the distortion generated by the nonlinearities has been obtained. Based on this expression, a compensation signal for the overall converter is calculated on each sample time, which is a fraction of the triangular carrier used to modulate each cell, thus significantly improving the quality of the output voltage signals. Experimental validation of the proposed compensation method is presented using a three-phase four-cell CHB converter prototype of 5.5 kW. [ABSTRACT FROM AUTHOR]

In this paper, a new isolated high step-up dc–dc converter is proposed based on the quasi-switched-boost network. The proposed converter has the following features: 1) continuous input current; 2) reduced turn ratio of the isolated transformer; 3) increased reliability, as it can operate in either short-circuit mode or open-circuit mode without causing damage to the power converter; and 4) unchanged primary and secondary voltage waveforms of the transformer, although the shoot-through duty cycle is variable. Compared to the quasi-Z-source-based isolated dc–dc converter, the proposed converter uses fewer passive components. The operating principles, analysis, parameter design guideline, and comparison with the quasi-Z-source-based isolated dc–dc converter are presented. A 450 W prototype is built to test the proposed converter. The proposed converter is applicable for distributed power generation applications where a varying low dc input voltage is converted to a high stabilized dc output voltage with a galvanic separation requirement. [ABSTRACT FROM AUTHOR]

The reduced capability of multilevel converters with more than one intermediate node to balance the dc-link capacitors voltage, as well as the lack of standard modulation methods to improve their balancing performance, makes these converter topologies unattractive for real power applications. This is especially true when the load demands active power. One of these topologies is the five-level multipoint clamped (5L-MPC) converter. The back-to-back (B2B) configuration of two 5L-MPC converters and the use of a space vector modulation (SVM) that exploits the voltage balancing capability of the redundant switching vectors extend the operation conditions range in which a proper voltage balance can be achieved. However, if practical modulation restrictions are considered (limitation of voltage steps, dead times, switching losses, etc.), the voltage balance cannot be achieved for all operation conditions. In this paper, an SVM which takes into account practical restrictions is proposed. In order to guarantee the voltage balance at any operation condition, the grid-side rectifier exchanges reactive power with the grid-side LCL filter. Thus, the voltage balance of the dc-link is guaranteed while a unity grid-side power factor is achieved. The proposed modulation scheme and the voltage balancing strategy are experimentally validated in a 6.6 kV 1.5 MW 5L-MPC B2B converter. [ABSTRACT FROM AUTHOR]

This paper proposes a new configuration for static ground power unit (GPU) based on the novel 25-level hybrid active neutral-point-clamped (HANPC) converter. The superiority of the proposed converter, as compared with conventional and other suggested multilevel converters, is significant decreasing the number of switches and minimizing the number of flying capacitors (FC) in converter. This improvement is possible by using suggested low-voltage submodule converter to the ANPC converter and proposed modulation method. This results in reduction of the size and cost of converter and makes it more feasible and reliable. Applying the active voltage balancing method for FC in the proposed HANPC converter guaranties fast charging and voltage-level regulation of FC without using balance booster circuit. Improving output voltage spectrum leads to inductance reduction of output L–C filter which enhances static GPU performance. The simulation and experimental results verify the validity and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

Multiterminal converters eliminate using several single-input-single-output converters and simplify their topologies and reduce their cost. In this paper, a new family of multi-input converters based on three switches leg is introduced. Inputs of the proposed converters are similar and they are topologically interchangeable and have boost or buck operation modes. The proposed converter has one output that operates as an inverter. Here, all operating modes of the proposed converters and their effects on each other are investigated, in details. Also, an appropriate switching technique for the converters is given. A detailed comparison between conventional and proposed two-input converters is also presented. A two-input, one-output prototype converter has been implemented to validate the given analyses and to verify the proposed converter's performance. The experimental results are in good agreement with the theoretical and simulated analyses. [ABSTRACT FROM AUTHOR]

In this paper, a novel cascaded seven-level inverter topology with a single input source integrating switched-capacitor techniques is presented. Compared with the traditional cascade multilevel inverter, the proposed topology replaces all the separate dc sources with capacitors, leaving only one H-bridge cell with a real dc voltage source and only adds two charging switches. The capacitor charging circuit contains only power switches, so that the capacitor charging time is independent of the load. The capacitor voltage can be controlled at a desired level without complex voltage control algorithm and only use the most common carrier phase-shifted sinusoidal pulse width modulation strategy. The operation principle and the charging–discharging characteristic analysis are discussed in detail. A 1-kW experimental prototype is built and tested to verify the feasibility and effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper proposes a unified PWM method for matrix converters so as to establish a common platform which can generate various types of PWM methods in real time by adjusting the free parameters in the modulation algorithm. As a foundation for unification, the general form of the modulation functions for matrix converters is derived using geometric transformation approach. All eligible direct modulation matrices are shown to be of indirect form and are expressed in terms of instantaneous phase quantities. This paper also presents a new viewpoint to consider a matrix converter as a generalized three-level inverter and to apply the double-carrier-based dipolar modulation technique of the three-level inverter to the matrix converter. Several concepts of the two-level PWM inverters are then generalized to the matrix converters for better visualization and understanding of the modulation process. [ABSTRACT FROM AUTHOR]

The main objective of this paper is to simplify the implementation of continuous and discontinuous 3-D space vector pulsewidth modulations (SVPWMs). This paper analyzes the relationships, whether in abc or \alpha\beta 0 coordinates, between three-phase voltages and the following elements: the tetrahedron in which the reference vector resides, three adjacent active switching vectors (or three switching states), and their duration times. Based on the analysis, the calculation of the turn-on time of each switch in the actual implementation is simplified, and discontinuous PWM (DPWM) methods in three-leg inverters can be extended to four-leg inverters without the phase angle. In addition, two more DPWM methods that are peculiar to 3-D SVPWM are presented. This simplified algorithm does not use irrational operations or look-up tables, and it alleviates the computation burden of the processor. The simulation and experimental results are provided to validate the effectiveness of the proposed algorithm. [ABSTRACT FROM AUTHOR]

This paper proposes an indirect matrix converter (IMC) topology to supply a five-phase load directly from three-phase ac power sources without bulky electrolytic capacitors and explains its operating principle. Using the emerging topology, which combines the five-leg inverter into the rectifier stage of the conventional IMC, the three-to-five-phase IMC topology reduces the number of power switches and results in a simpler commutation compared with the conventional three-to-five-phase direct matrix converter. In addition, a simple approach to realize the carrier-based pulsewidth modulation (CBPWM) method for a three-to-five-phase IMC is presented, and the proposed CBPWM method is analyzed based on the space-vector approach. As a result, the IMC with the proposed CBPWM method can be more easily implemented compared with IMCs with the space-vector PWM method. A three-to-five-phase IMC control platform is realized by coordinating a TMS320F28335 DSP (Texas Instruments) with an EPM7128SLC84-15 field-programmable gate array (Altera). The simulation and experimental results are provided to verify the effectiveness of the CBPWM strategy. [ABSTRACT FROM AUTHOR]

In this paper, an advanced configuration for a symmetric multilevel voltage source inverter is proposed. The authority of the proposed inverter versus the conventional cascaded H-bridge inverter and those most recently introduced is verified with provided comparisons. The proposed inverter is able to generate the desired voltage levels using a lower number of circuit devices, including power semiconductor switches and related gate driver circuits of switches. As a result, the total cost is considerably reduced, and the control scheme gets simpler. Moreover, the reduced amount of on-state switches in the suggested configuration decreases voltage drops. Furthermore, power losses are diminished. The given simulation results confirm the feasibility of the proposed configuration. To approve the practicability of the proposed inverter, a prototype of the proposed topology has been implemented. Finally, simulation and experimental results are compared, and the provided comparison shows that the obtained results are in good agreement. [ABSTRACT FROM PUBLISHER]

In this paper, a new cascaded multilevel inverter is proposed. For the proposed inverter, two different algorithms to determine the magnitude of the dc voltage sources are proposed. Then, in order to generate maximum numbers of output voltage levels by using a constant number of power switches and/or dc voltage sources, several optimum structures of the proposed inverter are obtained. In comparison with the conventional cascaded multilevel inverters, the proposed inverter is able to generate a high number of output voltage levels by using a lower number of power electronic devices such as power switches, driver circuits, power diodes, and dc voltage sources. In addition, the low amount of blocked voltage by switches is another advantage of the proposed inverter. The accuracy performance of the proposed inverter in generating the positive and negative voltage levels is verified through the experimental results on a 61-level inverter. [ABSTRACT FROM PUBLISHER]

In this paper, the two-input buck converter is proposed as the dc/dc stage for photovoltaic (PV) cascaded converters. This converter is attractive for this application because it is cost effective and reliable and can achieve dual maximum power point tracking (MPPT) with only one power transistor. However, due to the simplified and integrated structure, the nonlinear characteristics of the converter and the two PV arrays complicate the control. By means of a small-signal modeling, the control theme of the two PV voltages is formulated, and the effect of the nonlinearities is presented. It is shown that, while fast voltage dynamics are achieved for the first input, the second-input voltage response depends on the second-stage converter control. Simulation and experimental results are reported to validate the theoretical analysis, showing the dual MPPT capability. [ABSTRACT FROM PUBLISHER]

This paper proposes novel multilevel ac/dc/ac converters with reduced number of semiconductor devices to achieve light weight, efficiency, and better input current quality. The proposed three-phase front-end bidirectional five-level (5L) rectifier and rear-end 5L inverter are constructed based on multiple-pole multilevel diode-clamped (M2DCC) approach, which consist a total number of 24 diode components clamped. Based on the M2DCC concept, the number of switching devices can be further reduced to construct a new unidirectional front-end rectifier (M2SCR). Comparative studies are conducted to analyze the performances of the two proposed front-end rectifiers with supportive mathematical derivations. Experimental prototypes have proven the feasibility of the proposed ac/dc/ac configurations. Results obtained show that low current harmonic distortions of 5% and high power factor of 0.99 are achieved with small input inductors despite low-switching-frequency operation at 1 kHz. [ABSTRACT FROM PUBLISHER]

In this paper, a new single-phase cascaded multilevel inverter is proposed. This inverter is comprised of a series connection of the proposed basic unit and is able to only generate positive levels at the output. Therefore, an H-bridge is added to the proposed inverter. This inverter is called the developed cascaded multilevel inverter. In order to generate all voltage levels (even and odd) at the output, four different algorithms are proposed to determine the magnitude of dc voltage sources. Reduction in the number of power switches, driver circuits, and dc voltage sources is the advantage of the developed single-phase cascaded multilevel inverter. As a result, the installation space and cost of the inverter are reduced. These features are obtained by the comparison of the conventional cascaded multilevel inverters with the proposed cascaded topology. The ability of the proposed inverter to generate all voltage levels (even and odd) is reconfirmed by using the experimental results of a 15-level inverter. [ABSTRACT FROM PUBLISHER]

An architecture of multiple-integrated converter modules sharing an unfolding full-bridge inverter with a pseudo dc link (MIPs) is proposed for grid-connected photovoltaic systems in this paper. The proposed configuration can improve the power conversion, the control circuit complexity, and the cost competitiveness. The proposed MIP is composed of distributed flyback dc–dc converters (DFCs) and an unfolding full-bridge inverter with an ac filter. The DFCs can eliminate the shading effect by using the individual maximum power point tracking. In conventional flyback-type single-phase utility-interactive inverters, discontinuous conduction mode and boundary conduction mode are popular because of the inherent constant current-source characteristics more desirable for grid connection and of the simple procedures for the controller design. However, the operating mode suffers from a large current stress of the circuit components, which leads to the low power efficiency. To avoid this, the DFCs operate under continuous conduction mode that allows reduced current stresses and increased power efficiency, as well as low material cost. The current control loop of the converters employs primary-side regulation contributing to improvement of dynamics as well as the cost reduction significantly due to the elimination of the high-linearity photocoupler device. Development of a new dc-current loop that maintains the level of dc-current injection into the grid within the levels stipulated by IEEE 1547 will be dealt as well. The performance validation of the proposed design is confirmed by experimental results of a 200-W hardware prototype. [ABSTRACT FROM PUBLISHER]

The three-level neutral-point (NP)-clamped (3L-NPC) converter is a promising multilevel topology in the application of megawatt wind power generation systems. However, the growing requirements by grid codes may impose high stress and even give reliability problem to this converter topology. This paper investigates the loss and thermal performances of a 10-MW 3L-NPC wind power inverter undergoing low-voltage ride-through (LVRT) operation. A series of new space vector modulation methods is then proposed to relocate the thermal loading among the power switching devices. It is concluded that, with the proposed modulation methods, the thermal distribution in the 3L-NPC wind power inverter undergoing LVRT becomes more equal, and the junction temperature of the most stressed devices can be also relieved. Also, the control ability of the dc-bus NP potential, which is one of the crucial considerations for the 3L-NPC converter, is even more improved by the proposed modulation methods. [ABSTRACT FROM AUTHOR]

Efficient energy conversion in low-voltage applications has gained more attention due to increasing energy costs and environmental issues. Accordingly, three-level converters have been discussed as an alternative to the standard two-level voltage-source converter because they offer an increased efficiency at higher switching frequencies. From a system perspective, the benefits of using three-level converters are not only limited to the converter itself, but there are additional positive impacts on the surrounding such as on the load machine losses or on the electromagnetic interference input filter volume. In this paper, a holistic comparison of advanced three-level topologies against the two-level topology is given. Simple analytical calculations and measurements show the benefits and the optimization potential concerning several aspects, such as the necessary semiconductor chip area, the harmonic losses in the load machine and in filter components, and the volume of passive components. [ABSTRACT FROM PUBLISHER]

Cascaded H-bridge multilevel power electronic converters generally require several dc sources. An alternative option is to replace all the separate dc sources feeding the H-bridge cells with capacitors, leaving only one H-bridge cell with a real dc voltage source. This will yield a cost-effective converter. However, the required capacitor voltage balancing is challenging. In this paper, using the phase-shift modulation approach, a new control method for cascaded H-bridge multilevel converters fed with only one independent dc source is presented. The proposed method has a wide voltage regulation range for the replacement capacitors in the H-bridge cells. Experimental and simulation results support the proposed control method. [ABSTRACT FROM PUBLISHER]

In this paper, a number of alternate-cascaded switched-inductor and tapped-inductor networks have been proposed for Z-source inverters. The resulting topologies have enhanced voltage-boost capability while retaining the usual voltage-buck flexibility of a conventional voltage-source inverter. The enhanced capability is achieved by using lower rated components that can more readily be found. These components are assembled without direct series connection and hence avoid unbalanced voltage sharing problems and losses linked to balancing resistive circuits. The component count is, however, high, meaning that the proposed inverters should only be considered when a design requires multiple lower rated components rather than a few higher rated ones. Analysis, simulation, and experimental results have already validated the concepts discussed. [ABSTRACT FROM PUBLISHER]

The five-level active neutral-point (NP)-clamped (ANPC) converter is a newly emerging topology which can overcome the drawbacks of traditional NP-clamped and flying-capacitor multilevel converters. This paper presents a comprehensive theoretical analysis of the NP potential balancing issue and demonstrates that the NP potential can be naturally balanced under ideal and steady conditions. An NP potential balancing method based on zero-sequence voltage injection is presented. By calculating the average NP currents of all key zero-sequence voltages, the most appropriate zero-sequence voltage is selected to generate the demanded NP current, which can also limit the switching frequency of the series-connected insulated-gate bipolar transistors to the fundamental frequency. A three-phase five-level ANPC inverter prototype is built up, and both steady and dynamic experimental results are presented to verify the validity of this method. [ABSTRACT FROM PUBLISHER]

The increasing number of distributed generation units has led to the development of microgrids, to which the distributed generators are commonly interfaced by means of a voltage-source inverter (VSI). When the microgrid is operating independently of the power system, i.e., in islanded mode, two levels of control can be distinguished for these VSIs: power control and voltage control (frequency and amplitude). The set-point values for the voltage controller are obtained from the power controller. This paper investigates theoretically and experimentally the benefits of using several PID control structures for the voltage control. Theoretical insights into the dynamics of such a system emphasize the benefits of measuring current signals for control purposes and adding voltage measurements to the output of the controllers. Direct voltage control and cascade voltage control are compared both with and without forward compensation of the grid voltage. Simulation and experimental results are given showing that such PID-type controllers on a digital signal processor are simple yet effective strategies for an accurate voltage control in islanded microgrids. [ABSTRACT FROM PUBLISHER]

This paper extends the Z-source concept to matrix converters and explores a family of Z-source matrix converters. Their principles and characteristics are analyzed, and a simplified voltage-fed Z-source matrix converter is used as an example to demonstrate its operation, voltage gain versus modulation index, PWM method, boost control, and implementation of the control. Both simulation and experimental results verify operation of the proposed Z-source matrix converter, analytical results, and control method. The Z-source converters can achieve buck and boost operation with reduced number of switches needed, therefore achieving low cost, high efficiency, and reliability, compared to the traditional matrix converters. [ABSTRACT FROM AUTHOR]

Power converters consisting of naturally commutated thyristors such as cycloconverters and current source inverters were the first to be used in driving electrical motors with variable speed, but now, due to their inferior performance compared to forced commutated converters, their use is restricted in the high voltage/high power range where the performance and cost of forced commutated switching devices are not yet competitive. Hybrid cycloconverters proposed recently are capable of improving the performance of cycloconverters by adding an auxiliary forced commutated inverter with reduced installed power. It will be shown that the new topology is not only able to improve the quality of the output voltage but is also able to enhance the control over the circulating current and, therefore, for some of the cycloconverter arrangements, to improve the input power quality. This paper evaluates the performance of a few standard and hybrid cycloconverter arrangements using both simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a novel matrix converter with one ac input and two ac outputs. The presented topology is based on the traditional indirect matrix converter, but with its rear-end six-switch inverter replaced by a compact nine-switch inverter. With only three extra switches added, the proposed converter can produce two sets of three-phase ac outputs, whose amplitudes, frequencies, and phases can appropriately be regulated. Features such as sinusoidal input and outputs, unity input power factor and minimum commutation count are all retained by the proposed topology, despite having an additional output. Its modulation is realized by the computationally less intensive carrier-based method, whose unique carrier requirements can easily be managed within a programmable logic device. Mathematical proof for validating sinusoidal input and outputs achieved by this modulation technique is also discussed, before being verified in simulation and experimentally, together with other findings. [ABSTRACT FROM AUTHOR]

Common-mode voltage (CMV) is responsible for overvoltage stress to the winding insulation and bearing damage of an ac motor. High dv/dt of CMV raises leakage currents, which can cause serious problems such as motor damage and electromagnetic noise to the equipment installed near the converter. This paper proposes two modulation strategies for indirect matrix converters that substantially eliminate CMV. The first method is developed by using the suitable couple of nonzero space vectors instead of zero space vectors in the inverter stage. The maximum voltage transfer ratio of this method is unaffected and remains 0.866. The second one, which is useful for low-voltage operation, is approached by choosing the medium and the lowest positive line-to-line input voltages in the rectifier stage to generate the dc-link voltage and by placing suitable zero space vectors in the inverter stage. In the second method, the maximum voltage transfer ratio is 0.5. Both methods can mitigate the peak value to 42%. In addition, while the first method provides the same performance to the conventional method, the second method can reduce significantly the harmonic components of line-to-line output voltage. Simulation and experimental results are shown to verify the effectiveness of the proposed methods. [ABSTRACT FROM AUTHOR]

This paper presents first an overview of the well-known voltage and current dc-link converter topologies used to implement a three-phase PWM ac–ac converter system. Starting from the voltage source inverter and the current source rectifier, the basics of space vector modulation are summarized. Based on that, the topology of the indirect matrix converter (IMC) and its modulation are gradually developed from a voltage dc-link back-to-back converter by omitting the dc-link capacitor. In the next step, the topology of the conventional (direct) matrix converter (CMC) is introduced, and the relationship between the IMC and the CMCs is discussed in a figurative manner by investigating the switching states. Subsequently, three-phase ac–ac buck-type chopper circuits are considered as a special case of matrix converters (MCs), and a summary of extended MC topologies is provided, including three-level and hybrid MCs. Therewith, a common knowledge basis of the individual converter topologies is established. [ABSTRACT FROM PUBLISHER]

This paper proposes an energy regeneration circuit for three-phase voltage-fed inverters using a modified Undeland snubber. The proposed system uses a quasi-square-wave zero voltage switching dc–dc auxiliary converter to regenerate the energy from snubber capacitor to the dc bus. The regenerative circuit uses a single active switch, and it operates independently of the three-phase inverter. Operation stages, theoretical waveforms, and a design methodology are presented. Experimental results based on a 4.5-kVA three-phase inverter prototype are included to validate the proposed topology. [ABSTRACT FROM PUBLISHER]

A multilevel multiphase space vector pulsewidth modulation (SVPWM) algorithm has been introduced recently, in which the reference is separated into an integer part and a fractional part. The fractional part is, in essence, a two-level multiphase space vector algorithm. This paper shows that, with appropriate adaptations, the fractional part of the general space vector multilevel multiphase PWM can be applied as a stand-alone PWM method in conjunction with two-level voltage-source converters with any number of phases. Simulation results of the five- and six-phase cases are shown, and the new algorithm is compared with another recent multifrequency SVPWM algorithm, which follows the standard approach of selecting the switching vectors and calculating their application times using dq planes. The experimental verification is provided using a five-phase two-motor series-connected induction motor drive, supplied from a custom-designed five-phase voltage-source inverter. [ABSTRACT FROM AUTHOR]