Search

The paper deals with some new results on the averaging theory approach for the analysis of feedback controlled pulsewidth modulation power electronic converters. It develops some considerations regarding the averaging approximation of time-variant differential systems proving an analytical relationship between the accuracy with which the solution of the averaged model converges to the solution of the original time-variant model (i.e., the switched model) and the switching frequency of the converters. This relation is valid both for stable and unstable systems. Moreover, this paper confirms, as corollary, that under suitable conditions (verified during the standard operations of the power electronic converters) the averaged model uniformly converges to the switched model. [ABSTRACT FROM AUTHOR]

This paper proposes a novel high step-up nonisolated single switch dc–dc converter suitable for regulating dc bus in various microsources especially for photovoltaic (PV) sources. Quadratic boost and switched-capacitor technique are used as primary and secondary circuits, respectively. A coupled inductor is applied to make a connection between them, so a high dc voltage gain is achieved. High efficiency is yield where voltage stress on active switch is alleviated by clamped capacitor; consequently, smaller \rmR\rm{DS(ON)} for power switch is required. On the other hand, input current of the proposed converter is continued, hence stress on the input source is reduced. The operating principles and steady-state analyses are discussed in detail for both continuous and discontinuous conduction modes. Also, the boundary condition is computed. To verify the performance of the proposed converter and theoretical calculations, a 250-W prototype converter is implemented with an input voltage of 24 V and an output voltage of 400 V designed especially for PV sources in continuous conduction mode operation. Finally, simulation results are confirmed by experimental results; maximum efficiency is occurred at 150 W and full-load efficiency is 92.96%. [ABSTRACT FROM AUTHOR]

This paper presents a new diagnostic technique for the diagnosis of open-circuit faults in matrix converters operating with an Optimum Alesina-Venturini modulation scheme. Compared to previous diagnostic techniques developed for matrix converters, the technique proposed in this paper has the major advantage of not requiring the installation of any additional sensors in the converter besides the ones already present for control purposes. Hence, it can be easily integrated into the control platform of the converter at no additional cost. In addition to the diagnostic approach, a new fault-tolerant switching strategy is also presented so that after the appearance of an open-circuit fault, the matrix converter can continue to run although with degraded performance, until a repair action can be taken. Several simulation and experimental results are presented, demonstrating the effectiveness and applicability of the developed techniques. [ABSTRACT FROM AUTHOR]

This paper proposes a unified PWM method for matrix converters so as to establish a common platform which can generate various types of PWM methods in real time by adjusting the free parameters in the modulation algorithm. As a foundation for unification, the general form of the modulation functions for matrix converters is derived using geometric transformation approach. All eligible direct modulation matrices are shown to be of indirect form and are expressed in terms of instantaneous phase quantities. This paper also presents a new viewpoint to consider a matrix converter as a generalized three-level inverter and to apply the double-carrier-based dipolar modulation technique of the three-level inverter to the matrix converter. Several concepts of the two-level PWM inverters are then generalized to the matrix converters for better visualization and understanding of the modulation process. [ABSTRACT FROM AUTHOR]

This paper proposes a novel family of cascade three-level (TL) ac–ac direct converters based on ac switch cells, which transfer unsteady high ac voltage with distortion into regulated sinusoidal voltage with low total harmonic distortion (THD). The topological family includes buck TL–boost, buck–boost TL, and buck TL–boost TL modes. In order to achieve a reliable TL ac–ac conversion, a double transient voltage feedback control strategy of the output voltage and the voltage across the flying capacitor is introduced in this paper. A 500-VA 220-V \pm10% 50-Hz ac/220-V 50-Hz ac prototype is presented with the experimental results to prove that the converters have four improved advantages simultaneously, including lower voltage across power switches, bidirectional power flow, low THD of output voltage, and higher input power factor. [ABSTRACT FROM AUTHOR]

Interleaving of voltage-source converter (VSC) legs enables higher output currents per phase, effectively increasing the power rating without increasing semiconductor ratings. However, the interleaved operation results in circulating currents between each phase converter legs as well as a zero-sequence circulating current (ZSCC), which become quite prominent when the converters operate with low switching frequencies. This paper demonstrates the interleaved operation of three-level converters under selective harmonic elimination pulsewidth modulation (SHE-PWM). A controller for the circulating current within the legs of each phase is also proposed. The controller is used in combination with optimally selected SHE-PWM patterns to generate the maximum number of voltage levels and minimize the peak value of the circulating current. Simulation and experimental results show the interleaved operation and the effect of SHE-PWM pattern selection in the overall system. [ABSTRACT FROM PUBLISHER]

Matrix converters (MCs) are considered as a step forward in ac/ac conversion, providing sine-in and sine-out voltages and currents, controlled input power factor, compact sight without the requirement of a dc bus capacitor, and bidirectional power flows. There are also drawbacks associated with this technology: More switching devices and associated gate driver circuit power supplies and protection systems are required. In this paper, a new low-cost self-powered supply for bidirectional insulated-gate bipolar transistor/MOSFET switch gate drivers is presented. The proposed circuit allows the gate driver power supply of the bidirectional switch without using a transformer or any external added dc supply. This method is characterized by a simple structure, which is cost and size effective, of the power electronics switch driver power supply with regard to those suggested in the literature. Simulation results are compared with experimental measurements for a three-phase-to-single-phase MC and validate the proposed circuit. [ABSTRACT FROM AUTHOR]

A predictive control scheme for the indirect matrix converter including a method to mitigate the resonance effect of the input filter is presented. A discrete-time model of the converter, the input filter, and the load is used to predict the behavior of the instantaneous input reactive power and the output currents for each valid switching state. The control scheme selects the state that minimizes the value of a cost function in order to generate input currents with unity power factor and output currents with a low error with respect to a reference. The active damping method is based on a virtual harmonic resistor which damps the filter resonance. This paper shows experimental results to demonstrate that the proposed control method can generate good tracking of the output-current references, achieve unity input displacement power factor, and reduce the input-current distortion caused by the input filter resonance. [ABSTRACT FROM AUTHOR]

This paper extends the Z-source concept to matrix converters and explores a family of Z-source matrix converters. Their principles and characteristics are analyzed, and a simplified voltage-fed Z-source matrix converter is used as an example to demonstrate its operation, voltage gain versus modulation index, PWM method, boost control, and implementation of the control. Both simulation and experimental results verify operation of the proposed Z-source matrix converter, analytical results, and control method. The Z-source converters can achieve buck and boost operation with reduced number of switches needed, therefore achieving low cost, high efficiency, and reliability, compared to the traditional matrix converters. [ABSTRACT FROM AUTHOR]

This paper describes a novel fault-tolerant matrix converter motor drive system which requires an appropriate control strategy and the application of an effective fault detection technique. Two types of fault-tolerant matrix converter, a direct matrix converter and an indirect matrix converter, are proposed for a permanent magnet synchronous motor drive against open-circuit faults in safety-critical applications. A fault-tolerant control strategy is developed in order to maintain the continuous operation of the drive system with satisfactory performance. A high-speed fault detection strategy for detecting and identifying the faulty open-circuited switches located in the fault-tolerant four-phase direct matrix converter is also proposed. Simulation and experimental results are shown to demonstrate the effectiveness of the proposed fault-tolerant matrix converters and the developed fault detection strategy applied to the motor drive system under faulty operating conditions. [ABSTRACT FROM AUTHOR]

This paper presents a novel matrix converter with one ac input and two ac outputs. The presented topology is based on the traditional indirect matrix converter, but with its rear-end six-switch inverter replaced by a compact nine-switch inverter. With only three extra switches added, the proposed converter can produce two sets of three-phase ac outputs, whose amplitudes, frequencies, and phases can appropriately be regulated. Features such as sinusoidal input and outputs, unity input power factor and minimum commutation count are all retained by the proposed topology, despite having an additional output. Its modulation is realized by the computationally less intensive carrier-based method, whose unique carrier requirements can easily be managed within a programmable logic device. Mathematical proof for validating sinusoidal input and outputs achieved by this modulation technique is also discussed, before being verified in simulation and experimentally, together with other findings. [ABSTRACT FROM AUTHOR]

The matrix converter system is becoming a very promising candidate to replace the conventional two-stage ac/dc/ac converter, but system reliability remains an open issue. The most common reliability problem is that a bidirectional switch has an open-switch fault during operation. In this paper, a matrix converter driving a speed-controlled permanent-magnet synchronous motor is examined under a single open-switch fault. First, a new fault-detection method is proposed using only the motor currents. Second, a novel fault-tolerant switching strategy is presented. By treating the matrix converter as a two-stage rectifier/inverter, existing modulation techniques for the inverter stage can be reused, whereas the rectifier stage is modified by control to counteract the fault. However, the proposed techniques require no additional hardware devices or circuit modifications to the matrix converter. Experimental results show that the proposed method can maintain the motor speed with a maximum ripple of 2%—a fivefold improvement over the uncompensated system. The proposed method therefore offers a very economical and effective solution for the matrix converter fault tolerance problem. [ABSTRACT FROM AUTHOR]

The matrix converter is an array of controlled bi-directional semi-conductor switches that allows direct ac–ac conversion without an intermediate dc link. This converter has several attractive features that have been investigated in the last two decades. Multilevel converter technology has become increasingly popular in recent years due to high power quality, high-voltage capability, low switching losses and low EMI issues. This paper is concerned with applying multilevel techniques to direct ac–ac power converters and concentrates on developing the concepts of space vector modulation for a multilevel matrix converter. Results from a small-scale experimental prototype are presented to validate the theoretical findings. [ABSTRACT FROM AUTHOR]

A novel voltage-based commutation (VBC) strategy without explicit input-voltage measurement is proposed in this paper. By properly selecting the width of the critical intervals, the two-step uncritical commutation and four-step critical commutation approaches are utilized to realize safe VBC. The general switching patterns of space-vector modulation (SVM) are analyzed, and the four-step critical commutations are avoided by using four selected SVM switching patterns; thus, all the commutations in the matrix converter can be achieved by two-step VBC. In order to prevent the commutation processes from being interrupted, the triple-zero-vector switching pattern and the single-zero-vector switching pattern are utilized by selecting an appropriate commutation time and the output-voltage/current distortion is minimized. Prototype experiments have been carried out to show the validity of the control strategies. [ABSTRACT FROM AUTHOR]

Multilevel voltage-source converter topologies are widely used today in high-power applications such as medium-voltage drives. On the other hand, studies on matrix converters (MCs) have been mainly limited to the low power range. With the intention to combine benefits from both multilevel structure and direct power conversion, this paper investigates the topologies and operating principles of multimodular MCs (MMMCs). Composed of three-phase-to-single-phase MC (3 \times 2 MC) modules, two versions of MMMCs are presented and studied. Modulation schemes to synthesize sinusoidal waveforms on both input and output sides of the converters are elaborated. Having features such as modular design, relatively low switching frequency, and capability of using low-voltage power semiconductor devices, the presented MMMCs are intended for possible use in higher power applications where four-quadrant operation and fast dynamic response are expected. Simulation and experimental results are provided to verify the validity of the study. [ABSTRACT FROM AUTHOR]

The matrix converter (MC) is arousing considerable attention as an alternative for conventional ac/ac converters due to the advantages it offers. However, the control and modulation of this converter is complex. This, together with the fact that the MC usually operates at high modulation frequencies, makes the computational load of the platform to be simulated excessively high. All this makes the simulation time of models including the MC excessively long, even more so when both the transient and steady state of the system must be analyzed. This paper presents a new MC simulation technique called Switching State Matrix Averaging (SSMA). Although this is a fixed-step technique, a long simulation step can be used without forfeiting the accuracy of an ideal variable-step simulation. Likewise, the SSMA drastically speeds up the simulation, reducing the amount of required resources and the tuning time of the complex platforms in which the MC is used. A series of simulations has been performed in order to verify the proposed method. Moreover, a comparison between experimental and simulation results has been made, demonstrating the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This paper extends the single-phase self-driven synchronous rectification (SDSR) technique to multiphase ac–dc systems. Power MOSFETs with either voltage- or current-sensing self-driven gate drives are used to replace the diodes in the rectifier circuits. The generalized methodology allows multiphase SDSRs to be designed to replace the multiphase diode rectifiers. Unlike the traditional SR that is designed for high-frequency power converters, the SDSR proposed here can be a direct replacement of the power diode bridges for both low- and high-frequency operations. The SDSR utilizes its output dc voltage to supply power to its control circuit. No start-up control is needed because the body diodes of the power MOSFETs provide the diode rectifier for the initial start-up stage. The generalized method is demonstrated in 2-kW one-phase and three-phase SDSRs for inductive, capacitive, and resistive loads. Power loss reduction in the range of 50%–69% has been achieved for the resistive load. [ABSTRACT FROM PUBLISHER]