Search

In this paper, a hybrid switched-capacitor/switched-quasi-Z-source bidirectional dc–dc converter is proposed for electric vehicles (EVs) with hybrid energy sources, which has a wide voltage gain range in the bidirectional energy flows. Compared with the traditional quasi-Z-source bidirectional dc–dc converter, the proposed converter only changes the position of the main power switch and employs a switched-capacitor cell at the output of the high-voltage side. Therefore, the advantages of the wide voltage gain range and the lower voltage stresses across the power switches can be achieved. The operating principle, the voltage and current stresses across the power switches, and the comparisons with other converters are analyzed in detail. Furthermore, the parameter design of the main components, the dynamic modeling analysis, and the voltage control scheme are also presented. Finally, the experimental results obtained from a 400 W prototype validate the characteristics and the theoretical analysis of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, performances on two kinds of aggregated flyback microinverters are compared in aspect of harmonic resonances, which are controlled by current feedback control and peak current control. Based on the Norton models of flyback microinverters obtained by a small-signal modeling approach, potential harmonic resonances with the grid are analyzed. Following that, an impedance-based stability criterion is proposed, where the resonance frequency can be calculated and predicted based on the derived Norton models and the system admittance matrix of aggregated microinverters. After comprehensive analysis and comparisons, it is found that the peak-current-control-based flyback microinverters has better performance on damping the harmonic resonances than the current feedback controlled one. Simulations and experiments are carried out for verifying the effectiveness of the presented models and the correctness of the analysis results. [ABSTRACT FROM AUTHOR]

Three-phase bridge converter is popular in ac–dc power conversion. The conventional sensor control with inner current loop and outer voltage loop is often used to control the three-phase bridge converter. Many three-phase sensorless control methods had been proposed to control the bridge converter with considering the inductance and inductor resistance. In this paper, the voltage drop of the power semiconductor is first considered in the proposed three-phase current sensorless control method. At first, the dynamic behaviors of three-phase bridge converter for power factor correction (PFC) applications are studied, and its equivalent three-switch model is developed. Based on this developed model, three-phase current sensorless control with only voltage controller is proposed. Additionally, the voltage-loop transfer function of PFC bridge converter controlled by the proposed method is modeled, and the result is helpful to obtain the controller parameter. The proposed control method is implemented on the DSP-based platform for evaluation. Finally, the provided simulation and experimental results demonstrate the performance of the proposed method. [ABSTRACT FROM AUTHOR]

This paper proposes a transformerless line-interactive uninterruptible power supply (UPS) with low ground leakage current. A high-efficiency bidirectional inverter is suggested, which performs the line-interactive UPS functions with low ground leakage current. It has a full-bridge inverter and a bidirectional switch, which operate with the unipolar pulsewidth modulation. Because the bidirectional switch operates at the line-frequency, switching losses can be lower than the previous transformerless inverters. As the inverter operates, the parasitic capacitance between the inverter and the ac voltage ground is clamped to zero voltage for a positive line cycle and to the ac voltage for a negative line cycle, respectively. Thus, the parasitic capacitance can be prevented from being charged or discharged, which ensures the absence of the ground leakage current. The operation modes of the proposed system are described. The control schemes are presented to design the proposed inverter for the line-interactive UPS. Experimental results for a 2.0 kW prototype are discussed to verify the performance of the proposed system. [ABSTRACT FROM AUTHOR]

This paper presents a passivity-based control (PBC) scheme for the switched reluctance generator (SRG) in small-scale wind energy conversion systems for dc microgrid applications. The main objective is to stabilize the output voltage in case the system supplies constant power loads (CPLs) and operates with maximum power point tracking (MPPT). Stability improvement and dc-link ripple reduction in the presence of CPLs is achieved using system-level modeling of SRG-based dc microgrid through the Euler-Lagrange system (ELS) from the viewpoint of the machine physical structure. Compared with other control methods, the proposed MPPT method based on passivity-based speed controller employs the back electromotive force (EMF) in the generation process as a position-dependent voltage source to overcome the major challenge of SRG complicated uncertain dynamic model. To deal with the time-varying inductance and back EMF of SRG, an adaptation mechanism is incorporated in the proposed adaptive PBC and the control design is constructed by using the Lyapunov theorem where the closed-loop stability is ensured. The effectiveness of the proposed method in avoiding instability effects of SRG and CPL with voltage ripple reduction and precise wind turbine speed tracking is investigated with simulation results and validated with experimental by using a four-phase, 8/6 SRG drive system. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high step-up dc–dc converter is proposed. Active–passive inductor cells (APICs) are used to extend the topology. The ability to achieve high gains is the main merit of the proposed topology. The proposed converter operates based on parallel charging and series discharging of the inductors. The converter also achieves high step-up voltage gain with appropriate duty cycle and low voltage and current stress on the power switches and diodes. The proposed converter is analyzed in operation modes. The main parameters of the converter such as voltage gain, voltage stress of semiconductor devices are calculated to compare with other structures. Considering the output voltage ripple and filter size, the proposed converter is designed. Moreover, the losses and efficiency of the converter are calculated. The performance of the proposed converter is validated by experimental results. [ABSTRACT FROM AUTHOR]

This paper introduces a switched-capacitor dc combiner suitable for energy harvesting applications. Since the dc voltage is small, addition of the voltages from different sources can boost the final output voltage with self-startup capability. This approach is valid for any number of dc voltage sources. To prove the energy harvesting principle, three sources are selected. The design of the three-input dc combiner, with no closed-loop controller, is fabricated in 0.13-\mu\textm CMOS technology and the chip area is 1.5 × 1.5 \textmm^2. With integrated tunable thyristor-based differential oscillators, the chip can combine power from all three inputs. Manual frequency modulation is used to deliver the maximum power to the load. The system has proven to be functional even if one or two of the sources is/are weak or not available. Finally, for indoor conditions, the power from three different solar cells is combined where 70 $\mu$ W is harvested with an open-circuit voltage of 1.4 V and the short-circuit current of 160 $\mu$A. [ABSTRACT FROM PUBLISHER]

This paper proposes an improved dc transformer (NDCT hereinafter) based on switched capacitor with reduced switches for the integration of low-voltage dc energy storage systems and medium-voltage dc power distribution grid. The topology, phase-shift (PS) shoot-through and multiple PS modulations, and voltage, current, and power characterizations, as well as commutation characterization and control strategy, are proposed and analyzed comprehensively. Compared with the traditional schemes, the proposed NDCT not only can enhance reliability and flexibility but can increase voltage adjustment and power transfer capabilities as well. Moreover, the current ripple performance and soft-switching performance are improved, and the number and capacity of switches are reduced, thereby increasing the efficiency and cost of the system. Finally, an NDCT prototype is built. Experimental results verify the correctness and effectively of the proposed solution. [ABSTRACT FROM PUBLISHER]

This paper characterizes the sampling effect in digital sinusoidal pulse width modulation (SPWM) of voltage source inverter (VSI). The time-domain analysis presented in this paper establishes the relation between the fundamental frequency, carrier frequency, and the sampling frequency at different modulation indices of the SPWM. The analysis investigates the effect of sampling frequency of the digital controller on the output of the VSI. It is shown that the low-frequency harmonic components appear in the frequency spectrum of the VSI output voltage due to sampling. As a result, the output current of digitally controlled VSI is stepped in nature. The double Fourier integral solution of the switched waveform for inner and outer integral limits has been used to derive the expression. The integral solution is obtained using Jacobi-Anger expansions. The generalized results developed in this paper are useful to investigate the sampling effect in high switching frequency DSPWM. The proposed sampling effect has been analyzed for SPWM of single-phase H-bridge inverter. The analytical results are verified using simulation and experimental results. The experimental results have been obtained with the use of field-programmable gate array (FPGA) as a digital controller. [ABSTRACT FROM PUBLISHER]

This paper presents a comprehensive analysis of the current-stress optimization and soft-switching operation of the isolated bidirectional dual active bridge (DAB) dc–dc converter with the unified triple-phase-shift (UTPS) control. On this basis, the current-stress-optimized modulation scheme is proposed for DAB, which leads to the minimum current stress with the required transmission power and voltage conversion ratio in the whole load range. Moreover, the full soft-switching operation is achieved for the converter simultaneously. Distinct from the previous modulation schemes, the proposed optimized modulation scheme is deduced from a unified analysis of TPS where all effective switching modes are investigated. A novel algorithm based on the Karush–Kuhn–Tucker (KKT) conditions is originally proposed to derive closed-form solutions for the global optimal control parameters. This paper also presents a typical closed-loop control strategy for DAB with TPS control and detailed descriptions about the closed-loop operation. A laboratory prototype is applied, and the experimental results validate that the current-stress optimization and efficiency improvement are realized by applying the optimized modulation scheme. The experimental results also verify the effectiveness of the closed-loop control strategy for DAB with TPS control. [ABSTRACT FROM PUBLISHER]

Proper use of phase-controlled switching technology by controlling the making or breaking of the circuit breaker (CB) at predetermined phase angles of current or voltage can improve the service life of the CB, avoid relay protection device from mal-operation, and reduce the impact on the power grid when power equipment or load is energized or taken out. This paper proposes a novel phase-controlled switching method to address the influence of residual flux for three-phase wye winding unloaded transformers with three limbs, such as large capacitor variable frequency transformer or mine explosion-proof transformer. The optimal operation phase angle for CBs is firstly obtained via theoretical analysis. A model based on the alternative transients program/the electromagnetic transients program (ATP/EMTP) is then built to simulate the transient procedure of a power transformer during breaking and making. The simulated results confirm that the proposed switching strategy can reduce the excitation inrush current effectively when the unloaded transformers are energized. The experimental results reported in this paper are used to validate the accuracy and effectiveness of the phase-controlled switching strategy. [ABSTRACT FROM PUBLISHER]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

The traditional space-vector pulsewidth modulation (SVPWM) maximum voltage transfer ratio (VTR, i.e., the ratio of the output voltage fundamental amplitude to the input voltage fundamental amplitude) is 0.866 in a linear modulation region. In this paper, the output voltage fundamental amplitude and total harmonic distortion (THD) affected by a basic vector and a hexagon vector in traditional indirect SVPWM overmodulation are analyzed. The traditional indirect SVPWM overmodulation usually focuses on the inverter stage to improve the VTR, and there are few methods considering both of the inverter and rectifier stages to improve the overmodulation performance of a matrix converter (MC), including output voltage error, and output and input current THDs. In this paper, a new overmodulation method based on indirect SVPWM is presented. Both the output performance and input performance of the MC with the proposed and traditional overmodulation methods are emulated and tested. Simulation results indicate that the output voltage error and the input current THD are smaller and lower, respectively, with the proposed method. Experimental results verify that theoretical analysis is right, and the proposed overmodulation method is feasible. [ABSTRACT FROM PUBLISHER]

A four-level five-phase open-end winding (OeW) drive topology is introduced in this paper. The drive comprises a five-phase induction machine with open-end stator windings, supplied using two two-level voltage-source inverters with isolated and unequal dc-link voltages, in the ratio 2 : 1. The topology offers the advantages of a modular structure with fewer semiconductor components and has a greater potential for fault tolerance, as compared with an equivalent single-sided four-level drive. Due to the large number of switching states, development of a suitable space vector pulsewidth-modulation (PWM) method can be challenging. Hence, this paper examines the implementation of two-level-shifted carrier-based PWM methods. The effect of dead time on the drive performance is discussed, and it is shown that simultaneous PWM switching of both inverters can lead to degraded output phase voltage waveforms. Detailed analysis of this phenomenon is presented, a solution is proposed, and the modified modulation techniques are incorporated in an experimental setup, at first in conjunction with $V/f$ control. Once the proof of concept has been provided, full field-oriented control is implemented in this OeW drive topology for the first time; detailed experimental testing is conducted, and results are reported. [ABSTRACT FROM AUTHOR]

The current-fed dual active bridge (CF-DAB) dc–dc converter gains growing applications in photovoltaic (PV) and energy storage systems due to its advantages, e.g., a wide input voltage range, a high step-up ratio, a low input current ripple, and a multiport interface capability. In addition, the direct input current controllability and extra control freedom of the CF-DAB converter make it possible to buffer the double-line-frequency energy in grid-interactive PV systems without using electrolytic capacitors in the dc link. Therefore, a PV system achieves high reliability and highly efficient maximum power point tracking. This paper studies the optimized operation of a CF-DAB converter for a PV application in order to improve the system efficiency. The operating principle and soft-switching conditions over the wide operating range are thoroughly analyzed with phase-shift control and duty-cycle control, and an optimized operating mode is proposed to achieve the minimum root-mean-square transformer current. The proposed operating mode can extend the soft-switching region and reduce the power loss, particularly under a heavy load and a high input voltage. Moreover, the efficiency can be further improved with a higher dc-link voltage. A 5-kW hardware prototype was built in the laboratory, and experimental results are provided for verification. This paper provides a design guideline for the CF-DAB converter applied to PV systems, as well as other applications with a wide input voltage variation. [ABSTRACT FROM PUBLISHER]

Filters for switching ripple attenuation are essential at the input, and sometimes at the output for certain applications, for the deployment of matrix converters (MCs). Due to the absence of inertial elements in the MC structure and the consequent tight input–output coupling, the filter parameters significantly affect its dynamic behavior. This paper presents an exhaustive filter design method for synchronous applications of the MC in power systems. Apart from the usual considerations of ripple attenuation, voltage regulation, reactive current loading, and internal losses, this paper also addresses additional constraints which may be imposed by requirements of dynamic performance and reliable commutation. Rigorous analytical justification of each design step is provided and the sequential design process is summarized. Relevant experimental results are presented to validate the proposed design tool. [ABSTRACT FROM PUBLISHER]

In this paper, the conventional I- and T-type three-level neutral-point-clamped (3L-NPC) inverter for low-voltage renewable energy systems is first investigated. Literature research shows that the T-type inverter improves I-type's insulated-gate bipolar transistor (IGBT) $+$ IGBT current paths. However, the IGBT $+$ diode paths are the same. The calculation in this paper further reveals that the IGBT $+$ diode current paths dominate the conduction losses and even the whole semiconductor losses. Based on the aforementioned recognitions, a novel T-type inverter is presented as an alternative to be applied in the low-voltage renewable energy systems. In the proposed 3L-NPC, four CoolMosfets replace the IGBT $+$ diode middle bidirectional switch. In the proposed topology, there is no diode involved in the current path supposing the unity power factor. In this way, the conduction loss is expected to be reduced compared with that from the conventional T-type 3L-NPC, particularly in the low and medium power ranges. [ABSTRACT FROM PUBLISHER]

In this paper, a novel transformerless interleaved high step-down conversion ratio dc–dc converter with low switch voltage stress is proposed. In the proposed converter, two input capacitors are series-charged by the input voltage and parallel-discharged by a new two-phase interleaved buck converter for providing a much higher step-down conversion ratio without adopting an extreme short duty cycle. Based on the capacitive voltage division, the main objectives of the new voltage-divider circuit in the converter are for both storing energy in the blocking capacitors for increasing the step-down conversion ratio and reducing voltage stresses of active switches. As a result, the proposed converter topology possesses the low switch voltage stress characteristic. This will allow one to choose lower voltage rating MOSFETs to reduce both switching and conduction losses, and the overall efficiency is consequently improved. Moreover, due to the charge balance of the blocking capacitor, the converter features automatic uniform current sharing characteristic of the interleaved phases without adding extra circuitry or complex control methods. The operation principles and relevant analysis of the proposed converter are presented in this paper. Finally, a 400-V input voltage, 25-V output voltage, and 400-W output power prototype circuit is implemented in the laboratory to verify the performance. [ABSTRACT FROM PUBLISHER]

The parameters of electrical energy such as voltage amplitude are very important, particularly from the viewpoint of the final consumer and sensitive loads connected to the grid. The dynamic states in the power grid—deep voltage sags and swells—might cause faults and defects in sensitive loads. This paper deals with a three-phase hybrid transformer (HT) without dc energy storage to compensate voltage sags and swells and to protect sensitive loads against the rapid and extensive changes in supply voltage amplitude. The analyzed HT contains two main units: the first one is the conventional electromagnetic transformer, realizing an electromagnetic coupling, and the second one is the buck–boost matrix-reactance chopper, realizing an electrical coupling in the HT unit. In the presented solution, output voltage is transformed in two ways—electromagnetically and electrically. This paper presents an operational description, the theoretical analysis, and the experimental test results from a 2-kVA laboratory model. On the basis of the authors' research, it can be stated that the HT makes it possible to compensate deep voltage sags (deeper than 50% of nominal source voltage) and overvoltages (up to 140% of nominal source voltage) while maintaining good dynamic properties. The main advantages of the proposed solution, in comparison to other conventional solutions, are the ability to control the output voltage in the range of 0.66–3.5 US, good dynamics (transient state during source voltage uS amplitude change is shorter than 10 ms), and galvanic separation between source and load (such as in the case of the conventional electromagnetic transformer). [ABSTRACT FROM PUBLISHER]

Peak current mode (PCM) control has been widely used for the control of switching dc–dc converters due to its excellent transient performance. With the development of single-inductor dual-output (SIDO) dc–dc converters, PCM control technique is introduced to the control of SIDO dc–dc converters. Conventional PCM buck converter has only one reference current, with two inductor current borderlines are used to divide the operation modes of inductor current. However, PCM SIDO buck converter has more inductor current borderlines as it has one more reference current than that of PCM buck converter. In this paper, inductor current borderlines of PCM SIDO buck converter are investigated, and unified discrete iterative model of PCM SIDO buck converter is established. The effect of the difference of reference currents, initial inductor current and input voltage on the stability of PCM SIDO buck converter has been discussed by using bifurcation diagrams. The study results show that the stability of PCM SIDO buck converter is sensitive to the difference of reference currents, initial inductor current and input voltage. The stability boundary of the difference of reference currents, stability region of initial inductor current, and stability boundary of input voltage are derived. Lyapunov exponent and experimental results are carried out to verify the theoretical analysis results. [ABSTRACT FROM PUBLISHER]

Due to the relatively low output voltage of photovoltaic (PV) source, a high step-up converter with high efficiency is needed when the PV source is connected to the power grid. A novel high step-up converter based on two switched capacitors and a coupled inductor is proposed in this paper. The operating principle is analyzed and the voltage gain is derived. A 100-W prototype is fabricated in the laboratory to verify the theoretical analysis, and the highest efficiency is 96.4%. [ABSTRACT FROM PUBLISHER]

In this paper, the remedial operation of switch faults will be investigated comprehensively for T-type-three-level-inverter-fed dual three-phase motor drives. The open-circuit switch faults in multiple phase legs are discussed at first. The faulty conditions are classified into five categories. Different remedial strategies, namely Type-I to Type-V schemes, are proposed for different faulty conditions. In particular, three kinds of Type-III fault-tolerant control schemes are proposed by using medium-voltage vectors to synthesize small-voltage vectors, in such a way that the mid-point voltage in a dc link can be stabilized well. Then, the short-circuit faults in both clamping switches and half-bridge switches are investigated. By analysis, their operation conditions are equivalent to conditions loss of both P and N voltage levels and open-phase faults, respectively. Thus, the corresponding remedial strategies can be applied accordingly. Particularly, a voltage compensation control method is proposed for conditions, where open-switch faults coexist with open-phase operation induced by short-circuit faults in half-bridge switches. The validity of all of theoretical analysis and the proposed remedial strategies has been verified by experiments. [ABSTRACT FROM PUBLISHER]

In trasformerless grid-connected photovoltaic (PV) systems, common-mode voltage (CMV) fluctuations cause leakage current flow through the stray capacitance of the PV panels. Shoot-through states in a quasi-Z-source inverter (q-ZSI) increase the amplitude of high-order harmonics of CMV. In this paper, by using the modulation technique based on odd pulse width modulation and minor change in the Z network of the three-phase q-ZSI, the leakage current is blocked. No extra semiconductor element is added. By the proposed technique, CMV is kept nearly constant during switching cycles. The experimental results for CMV analysis in a \text1\;\textkW prototype are presented to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

Multilevel inverters (MLIs) have replaced conventional two-level inverters for medium-voltage high-power industrial applications. One of the best modulation techniques for MLIs is the space vector modulation (SVM). Although SVM has its own advantages, it has been overlooked for much simpler carrier-based modulation schemes in the industry. Nearest level modulation (NLM) is a simple alternative, which is functionally similar to SVM. In this paper, a new generalized SVM algorithm is presented, in which the SVM is achieved using the concept of NLM. A generalized switch matrix is introduced to derive gate pulses for the inverter, which further simplifies the algorithm. The algorithm is tested and verified for a three-phase, three-level, and five-level neutral-point-clamped inverters in both simulation and hardware. [ABSTRACT FROM PUBLISHER]

This paper proposes a multiloop framework for current control of grid-connected voltage source inverters (VSIs) with LCL output filter. The discrete-time model is of third-order with a nonminimum phase zero when controlling the grid side current. This poses some difficulties on the design of most types of controllers. Motivated by this problem, the inner loop is implemented by a discrete-time sliding mode control law to ensure the tracking of the converter side current. This can be achieved regardless the grid impedance and voltage, making the converter to behave like a current source inverter with a capacitive+inductive (CL) filter. Thus, the problem of current control falls from a third-order system to a second-order system. Several types of controllers can be designed to implement the outer loop based on the equivalent CL circuit. In this work, a resonant controller with a virtual resistor was applied. Simulations and experimental results are presented to validate the proposal. [ABSTRACT FROM PUBLISHER]

This paper extends the trans-Z-source concept to ac–ac power conversion and proposes a novel single-phase trans-Z-source ac–ac converter. The proposed converter retains the advantages of its existing Z-source/quasi-Z-source counterparts in which the output voltage can be boosted and in-phase with the input voltage or bucked/boosted and out-of-phase with the input voltage. Meanwhile, a coupled inductor is introduced into the proposed converter, and the turns ratio of the coupled inductor become another control variable beside the duty cycle to obtain extreme voltage gain. Importantly, the input voltage and output voltage share the same ground, and the input current could be continuous, which is a benefit for reducing input current harmonics. Most important of all, the safe-commutation strategy for the proposed converter is deep developed, and analytic expression between the switches state and loop circuit voltage/current condition is derived out. Hence, the current/voltage ripple can be avoided without a loss snubber circuit, which benefits a reduced cost and enhanced reliability. The performance analysis is discussed in consideration of parasitic resistance, and system parameter design is optimized based on theoretic calculation. A laboratory prototype is fabricated, and experiments are performed to verify the validation of the proposed converter. [ABSTRACT FROM PUBLISHER]

A common ground switched-quasi-Z-source bidirectional dc–dc converter is proposed for electric vehicles with hybrid energy sources. The proposed converter is based on the traditional two-level quasi- Z-source bidirectional dc–dc converter, changing the position of the main power switch. It has the advantages of a wide-voltage-gain range, a lower voltage stress across the power switches, and an absolute common ground. The operating principle, the voltage and current stresses on the power switches, the comparisons with the other converters, the small signal analysis, and the controller design are presented in this paper. Finally, a 300 W prototype with $U_{{\rm{high}}}= {240 \ \rm{V}}$ and $U_{{\rm{low}}}= {40\sim 120\ \rm{V}}$ is developed, and the experimental results validate the performance and the feasibility of the proposed converter. [ABSTRACT FROM PUBLISHER]

Direct current voltages unbalance of respective power cells is an inherent and critical problem in a cascaded multilevel converter, which is widely used in the solid-state transformer. In this paper, an n -dimension space vector pulse width modulation is presented to address this issue in a three-level H-bridge-based cascaded multilevel converter. This algorithm utilizes the redundant switching pairs of the inner cell and the redundant vectors of mutual cells to balance capacitors’ and cells’ voltages. Meanwhile, a smooth vector transition strategy is included in this algorithm to avoid the level-skip phenomenon. The calculation processes are analyzed in one-cell, two-cells, and three-cells modes, respectively. It is simple, calculable, and flexible to extend in n-cells mode. Finally, the voltage balancing capacity of the inner cell and mutual cells with smooth level transition are verified by simulations and experiments not only at startup but also with unbalanced loads. [ABSTRACT FROM PUBLISHER]

This paper presents an optimized topology of 3-$\phi$ , multilevel inverter (MLI) configuration for five or higher level operation with reduced switch count. The proposed solution consists of two basic units (BUs) of multilevel converter and a T-structured 3-level inverter (3-LI). Both BUs are equally shared by the three phases maintaining symmetry among the phases. Moreover, for a higher level operation of the proposed MLI, the modifications required are at two BUs only and not at three legs of the inverter. It further helps in reducing the requirement of extra components for higher level operation compared to the conventional solutions. Furthermore, the topology also has the benefits of reduced switching and conduction loss. An algorithm is also devised to generate the switching pulses for the BUs and the 3-LI, using a carrier-based space vector modulation technique. Presented topology is compared with other existing topologies to prove its advantage. All the details regarding the operating modes and pulse width modulation techniques employed for the proposed system are given and supported by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

A modified scheme for reactive power compensation using static VAr compensators (SVCs) has been proposed in this paper for unbalanced four-wire system. The conventional SVC-based scheme requires both delta ( $\Delta $ $)$ - and star (Y)-connected SVCs for the same purpose. The proposed scheme uses a single-equivalent delta-connected thyristor controlled reactor (TCR) along with a combination of Y- and $\Delta $- connected thyristor switched capacitors for this purpose. The single-equivalent $\Delta $ -TCR in the present scheme is the result of a virtual Y-TCR and the conventional $\Delta $-TCR. This can reduces effective number of switching devices, cost, complexity, and space requirement compared to the conventional SVC-based schemes. Moreover, the proposed scheme can have various advantageous features compared to newly used DSTATCOM. The proposed scheme can also prevent injection of triplen harmonics in to the line, which is injected by Y-TCR in the conventional scheme. An optimized switching function is adopted in the proposed scheme for reduction of additional injected harmonics by TCR. The optimized switching angles are computed offline using gravitational search algorithm and stored in the processor memory for online application. The viability of the proposed scheme is simulated using MATLAB/Simulink and verified by suitable experimental results on a practical system. [ABSTRACT FROM AUTHOR]

Adding the auxiliary switches to the conventional H-bridge inverter is an effective way to eliminate the leakage current for transformerless PV systems, such as H5, H6, etc. Inspired by the newly developed embedded-switch H6 topology, a novel embedded-switch inverter (ESI) is proposed in this paper for three-phase transformerless PV systems. First, the operation principle and characteristics of the proposed ESI are analyzed. Second, the common-mode model of the three-phase ESI is established, based on which the main factors that affect the leakage current are discussed. The finding reveals that the switching states with conventional modulation strategy result in high-frequency common-mode voltage, which is the source of leakage current. In order to solve the problem, a new modulation strategy is presented for ESI to eliminate the high-frequency leakage current. Finally, the time-domain simulation and the experimental tests are carried out. The results verify the effectiveness of the proposed solution. [ABSTRACT FROM AUTHOR]

This paper proposes an interleaved-stage ac–dc bidirectional power converter topology feasible to medium-voltage railway systems. It is based on an arrangement that uses input-series-output-parallel configuration with identical power modules. Each module consists of two interleaved legs employing coupled windings so that it is possible to connect a medium-frequency transformer. The topology conception is presented, followed by the adopted control and modulation technique. An estimation of semiconductor losses is also discussed, while a comparative analysis by means of simulation results validates the improved performance of the introduced approach if compared with similar solutions. The topology results are obtainedt through a medium-voltage high-power railway application, demonstrating the converter functionalities and performance under both steady-state and dynamic conditions. It is then possible to state that good performance in terms of efficiency is achieved even though the power stage presents higher component count if compared with the topology that presents the best result, thus making it suitable to high-power ac–dc machine drive applications. [ABSTRACT FROM AUTHOR]

In this paper, dual-buck structured single-stage buck–boost inverters that use power MOSFETs to achieve high efficiency are presented. The proposed inverters require fewer switches, and half of the switches have reduced current stresses. They have no shoot-through problem; therefore, high system reliability can be obtained. The dead-time in PWM signals can be minimized or eliminated, which improving the quality of the output ac voltages and increasing the efficiency. In the proposed inverters, MOSFETs can be used without reverse-recovery issues of their body diodes to boost the efficiency and increase the switching frequency. To further improve the efficiency and stability of the proposed single-phase inverter, PWM strategies combining high- and low-frequency modulation are presented. A hardware prototype of the single-phase inverter was built and tested using resistive, inductive, and nonlinear loads. Experimental results for a 300-W prototype inverter show a 97.4% peak efficiency with a 25 kHz switching frequency. [ABSTRACT FROM AUTHOR]

The parallel three-phase grid-connected converters sharing dc and ac bus can increase the system power level effectively. However, the zero sequence circulating current (ZSCC) will occur inevitably under space vector pulse width modulation or discontinuous pulse width modulation (DPWM). In this paper, the mechanism and the mathematical model of ZSCC are studied. Then, a hybrid PWM (HPWM) strategy is proposed to suppress the ZSCC based on the same zero sequence voltage injected, which is dependent on the common grid information. The dc voltage utilization of HPWM can be extended compared with sinusoidal PWM (SPWM). The number of parallel modules can be infinity theoretically by using HPWM. It is noted that there is no internal commutation among modules (expect the dq current reference). Finally, the feasibility and the effectiveness of the proposed method are verified by experiments. [ABSTRACT FROM AUTHOR]

The battery energy-stored quasi-Z-source (BES-qZS)-based photovoltaic (PV) power generation system combines advantages of the qZS inverter and the battery energy storage system. However, the second-harmonic ( \text2\omega ) power ripple degrades the system's performance and affects the system's design. An accurate model to analyze the \text2\omega ripple is very important. The existing models did not consider the battery, or assumed a symmetric qZS network with $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$, which limits the design freedom and causes oversized impedance parameters. This paper proposes a comprehensive model for the single-phase BES-qZS-PV inverter system, where the battery is considered and there is no restriction of $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$ . Based on the built model, a BES-qZS impedance design method is proposed to mitigate the \text2\omega ripple with asymmetric qZS network. Simulation and experimental results verify the proposed \text2\omega ripple model and impedance design method. [ABSTRACT FROM AUTHOR]

Traditional model predictive control cost functions, when utilizing long prediction horizons ( $N\geq 10$) in power inverter applications, have demonstrated harmonic performances approaching that of schemes based on offline-generated optimal pulse patterns. However, long prediction horizons often prohibitively increase computational load. A different approach to maximizing harmonic performance is taken in this paper. It is shown that shaping the output voltage spectra using a simple feedback mechanism can significantly reduce the length of the required prediction horizon, facilitating a feasible computational load. When a short-horizon cost function is augmented by the feedback mechanism an excellent tradeoff between harmonic performance and switching loss is achieved, even with a prediction horizon of one. It is also shown that the feedback mechanism can be used to improve input reference tracking. Experimental verification of the proposed modulator is performed on a two-level three-phase inverter. [ABSTRACT FROM AUTHOR]

Several applications such as power supplies for electric precipitators, ozone generation, partial discharge, etc., require ac superimposed dc (ACsDC) voltage supply. Most of such applications use intransigent systems for producing ACsDC voltages. In this paper, three different kinds of flexible power electronic converters are proposed for producing ACsDC voltages. These converters have two power conversion stages: input and output. In the input stage, two isolated dc voltages are obtained by using an isolated three-port dc–dc converter or two isolated two-port dc–dc converters. In the output stage, one of the input-stage dc voltages is used to generate an ac voltage and the obtained ac voltage is added to the remaining input-stage dc voltage to obtain an ACsDC voltage. Based on the converters used in the input stage, the proposed ACsDC converters are named as a dual active bridge (DAB) converter-based ACsDC converter (DAB-ACsDC), triple port active bridge (TAB) converter-based ACsDC converter (TAB-ACsDC), and dual transformer-based asymmetrical triple port active bridge (DT-ATAB) converter-based ACsDC converter (DTATAB-ACsDC). A detailed analysis of these ACsDC converters and their verifications using simulations and experimental studies are presented, which depict that the proposed converters can be used effectively for producing ACsDC voltages. [ABSTRACT FROM AUTHOR]

This paper proposes an isolated single-ended primary-inductor converter (SEPIC) dc–dc converter with ripple-free input current and lossless snubber. The proposed converter is based on a conventional isolated SEPIC converter to enable electrical isolation and high voltage gain using a coupled inductor. The input current ripple is significantly reduced by utilizing an auxiliary circuit that also functions as a lossless snubber circuit with an additional diode. Moreover, the maximum switch voltage stress is clamped to a low voltage by the snubber circuit. Therefore, a low voltage rating mosfet that has low $R_{{\rm{DS(on)}}}$ can be utilized as a main switch device. Hence, the total power efficiency is improved. Experimental results from a 100 W prototype, which are presented to verify the theoretic analysis and performance of the proposed converter. [ABSTRACT FROM PUBLISHER]

DC microgrids are popular due to the integration of renewable energy sources such as solar photovoltaics and fuel cells. Owing to the low output voltage of these dc power generators, high efficient high gain dc–dc converters are in need to connect the dc microgrid. In this paper, a nonisolated high gain dc–dc converter is proposed without using the voltage multiplier cell and/or hybrid switched-capacitor technique. The proposed topology utilizes two nonisolated inductors that are connected in series/parallel during discharging/charging mode. The operation of switches with two different duty ratios is the main advantage of the converter to achieve high voltage gain without using extreme duty ratio. The steady-state analysis of the proposed converter using two different duty ratios is discussed in detail. In addition, a 100 W, 20/200 V prototype circuit of the high gain dc–dc converter is developed, and the performance is validated using experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, a new carrier-based pulse width modulation (PWM) strategy providing common-mode voltage (CMV) elimination and reduced current ripple in a three-level neutral-point-clamped inverter is introduced. The employed switching sequences are made up of the three zero CMV (ZCMV) vectors, and one among the three vec-tors is applied at two ends of a half-carrier cycle. The output current ripple characteristics pertaining to those switching sequences are investigated. In a carrier cycle, the root-mean-square current ripple minimization is analyzed and an optimal sequence is derived accordingly. The presented PWM scheme results in a considerably reduced current harmonic distortion in a wide modulation region as compared to the two existing ZCMV schemes on the same average switching frequency. Also, an implementation of sawtooth-carrier-based PWM patterns is proposed for further improvement of the harmonic performance. The algorithm requires small computational burden and is straightforward for an online implementation. Simulation and experimental results are both provided to validate the good performance of the proposed PWM method. [ABSTRACT FROM PUBLISHER]

In this paper, a single-phase multilevel ac/ac converter with reduced number of power semiconductor devices is proposed. For the simple case of a three-level converter, only three bidirectional switches and two capacitors are required. The proposed converter provides a highly sinusoidal and regulated output voltage with a simple topology. The efficiency is high because in each state of operation only one semiconductor conducts. The converter can be easily extended to any desired levels in the output voltage to even more reduce the output total harmonics distortion. Another advantage of the proposed converter is that by increasing the voltage levels, the stress on the switches will decrease. The proper performance of the proposed converter is confirmed through extensive simulation and experimental tests. [ABSTRACT FROM PUBLISHER]

In this paper, a power factor correction (PFC)-based switched reluctance motor (SRM) drive is proposed. Generally, the SRM drive is fed with a simple diode bridge rectifier followed by a bulky capacitor, which draws peaky current at low power factor and high-input-current total harmonic distortion (THD). Here, a dual output converter is proposed to control the SRM and to provide power quality improvement as well. This converter is a combination of Cuk and SEPIC converters, which produces two equal output voltages with neutral point N, to feed a midpoint converter of the SRM drive. The converter is designed to operate in discontinuous conduction mode of operation to obtain inherent PFC at supply side. The motor control is attained by regulating dc link voltage over a wide range. Test results on a prototype of the SRM drive demonstrate the excellent performance with high power factor and reduced input current THD. The observed power quality indices depict the improved power quality as per the standard IEC 61000-3-2. [ABSTRACT FROM PUBLISHER]

This paper proposes a new \boldsymbol n -port hybrid dc circuit breaker for offshore multiterminal HVDC grid application. The \boldsymbol n-port dc circuit breaker can substitute \boldsymbol n-1 hybrid dc circuit breakers at a dc bus with \boldsymbol n-1 adjacent dc transmission lines. The system-level behavior of the proposed multiport hybrid dc circuit breaker is similar to other hybrid dc circuit breakers. The operation principles of the proposed multiport dc circuit breaker are introduced, analyzed, and compared to the existing solution in this work. The components ratings are compared to the existing solution, and the functionality of the proposed device is verified by simulation. [ABSTRACT FROM PUBLISHER]

In this paper, an input-series two-transistor forward converter is proposed and investigated, which is aimed at high-input voltage multiple-output applications. In this converter, all of the switches are operating synchronously, and the input voltage sharing (IVS) of each series-module is achieved automatically by the coupling of primary windings of the common forward integrated transformer. The active IVS processes are analyzed based on the model of the forward integrated transformer. Through the influence analysis when the mismatches in various series-modules are considered, design principles of the key parameters in each series-module are discussed to suppress the input voltage difference. Finally, a 96-W laboratory-made prototype composed of two forward series-modules is built, and the feasibility of the proposed method and the theoretical analysis are verified by the experimental results. [ABSTRACT FROM PUBLISHER]

To achieve precise voltage value for modern model-based motor control strategies, an accurate voltage distortion compensation method for voltage source inverters is proposed in this paper. The voltage distortion principles of a mosfet-based inverter and an IGBT-based inverter are analyzed and compared. A graphical solution of compensating voltage error is proposed, all the voltage distortion factors are considered. A current observer is designed to overcome time delay, achieve precise current in each switching period for compensation. The proposed method is of high precision, intuitive, and easy to implement. The effectiveness of the proposed method is verified by experiments. [ABSTRACT FROM PUBLISHER]

This paper proposes a new bridge modular switched-capacitor-based ac–ac converter, which is intended to replace conventional transformers in commercial and residential applications, especially for microgrids. The main advantages of the proposed converter lie in high efficiency and power factor, bidirectional operation, and capacitor voltage self-balancing ability. Another distinct merit is its symmetric construction, with which the voltage ripple of charge/pump capacitors can be cancelled out, and the output voltage will be smooth with significant ripple reduction. It is also noteworthy that the symmetric construction ensures that the two symmetric parts can work independently under a simplified control strategy. In addition, the modular configuration contributes to convenient voltage extension. Compared with the reported flying-capacitor switched-capacitor ac–ac converter, the proposed converter requires fewer switches and capacitors per unit of voltage conversion, thus suffering lower voltage stress. To demonstrate the performance of the converter, a prototype with 600-W 220-Vrms high-side voltage, 55-Vrms low-side voltage, and a switching frequency of 100 kHz was designed and fabricated. The relevant experimental results are reported herein. The maximum and rated power efficiency obtained were 95.9% and 94.4%, respectively. [ABSTRACT FROM PUBLISHER]

This paper proposes a single-stage light-emitting diode (LED) driver based on an inverted buck topology, using current path control switches. The proposed circuit consists of a control circuit, a bridge diode, and an inverted buck converter with multiple switches connected to the LED segments in parallel. Whereas the typical buck LED driver operates with a fixed LED forward voltage, the proposed driver operates with a variable LED forward voltage, according to the input voltage level. Because of this capability to adjust the LED forward voltage, it can reduce the current ripple and the switching frequency with a small inductance value. In addition, it enables operation with LED lamps of a wide voltage range, while simultaneously achieving small dead-angles. The detailed operation principles are described, and the design considerations for the proposed driver are discussed. The proposed driver circuit and control operation are verified experimentally using a 7 W hardware prototype with four LED segments. The obtained experimental results show that under a 110 Vrms input voltage, the proposed driver achieves a power factor of 0.94 with a small dead-angle and an efficiency of 94%. [ABSTRACT FROM PUBLISHER]

Dead-time insertion increases noise and torque pulsation in motors under open-loop constant V/f control, and it results in instability in motors under sensorless field-orientated control or direct torque control at low speed, degrading performance of motor drive systems. In order to overcome the drawback of dead-time insertion, a novel current-detection-independent dead-time compensation technique based on terminal voltage A/D conversion is proposed in this paper. Both current polarity and compensation time can be extracted from the sampled terminal voltage. Experiments on an induction motor rated at 210 V, 2.2 kW demonstrated the proposed technique can significantly improve the performance of the fixed compensation, online compensation, and even the feedback compensation method. The proposed scheme does not rely on current sensors, and thus can be applied to both open-loop and closed-loop motor drive systems. When combined with the fixed compensation method, the performance of the proposed technique is even comparable with the feedback compensation method within a large frequency range, making it very attractive for open-loop constant V/f drives where current sensors are not available. [ABSTRACT FROM PUBLISHER]

In this paper, a new type of matrix converter (MC) also called a single-phase high-frequency transformer isolated (HFTI) buck MC is proposed. The proposed converter can provide step-down operation of the input voltage with various types of output voltages such as in-phase and out-of-phase output voltages, rectified (or positive) output voltage, and output voltage with step-changed frequency. By incorporating HFT isolation, the proposed MC saves an extra bulky line frequency transformer, which is required for the conventional MCs to provide electrical isolation and safety, when used in application such as dynamic voltage restorers, etc. Two different circuit variations of the proposed HFTI MC are presented with and without continuous output currents, with the latter having less passive components. The safe-commutation strategy is also employed for the proposed HFTI MC to provide current path for the inductor during dead-time, which avoids switch voltage spikes without adding any snubber circuits. The operation principle and circuit analysis of the proposed MC are presented, and switching strategies are also developed to obtain various output voltages. Moreover, a prototype of the proposed MC is fabricated, and experiments are performed to produce in-phase/out-of-phase and rectified output voltages, and output voltage with step-changed frequency. [ABSTRACT FROM PUBLISHER]

This paper presents a new buck–boost converter. Unlike the single-switch buck–boost converter, the proposed converter has low-voltage stresses on semiconductors. Moreover, although both the conventional two-switch buck–boost (TSBB) and the proposed converters have the same number of passive and active components, and the proposed converter can reduce the conduction loss as a result of having fewer conducting components. Therefore, the proposed converter obtained a higher efficiency than the TSBB converter. A 48-V output voltage and 150-W output power prototype was fabricated to verify the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]