Search

The three-phase four-leg inverter is very suitable for the high-power uninterruptible power supply application, and the load neutral point voltage (LNPV) should meet the requirement. In this paper, two factors influencing the LNPV were revealed first, which are the switching states and the ratio of the neutral inductance to the phase inductance (k). Then, the 16 switching states can be classified into four groups, and the ones in the first and the second group come to the minimum amplitude of LNPV with a specific ratio k respectively. Third, three methods to mitigate the LNPV were proposed based on the analysis of LNPV. In the first method, switching states in the first group are just utilized, and the LNPV can be eliminated with the ratio k of unity. In the second method, the switching states in the fourth class are avoided, and the LNPV can be reduced. Common mode filter is used in the third method and the LNPV can be mitigated effectively with the ratio k of unity. Furthermore, the power losses in the first and the second method were estimated and were compared with the original situation. Finally, the proposed methods were verified by simulation and experimental results. [ABSTRACT FROM PUBLISHER]

A neutral-point-clamped three-level inverter with small dc-link capacitors is presented in this paper. The inverter requires zero average neutral-point current for stable neutral-point voltage. The small dc-link capacitors may not maintain capacitor voltage balance, even with zero neutral-point current. This may happen due to nonlinearities present in the circuit. This requires a fast control of the neutral-point voltage. A simple carrier-based modulation strategy which allows modeling of the neutral-point voltage dynamics as a continuous function of power drawn from the inverter is proposed. This continuous model shows that the neutral-point current is proportional to the power drawn from the inverter, and it enables the use of a well-established classical control theory for the neutral-point voltage controller design. A simple proportional integral controller is designed for the neutral-point voltage control on the basis of the continuous model. The design method for optimum performance is discussed. The implementation of the proposed modulation strategy and the controller is very simple. The controller is implemented in a 7.5-kW induction machine-based drive with only 14 \mu \F dc-link capacitors. Also, the experimental results show that fast and stable performance of the neutral-point voltage controller are achieved and thus verify the validity of the proposed control approach. [ABSTRACT FROM PUBLISHER]

Multilevel inverters have been widely accepted for high-power high-voltage applications. Their performance is highly superior to that of conventional two-level inverters due to reduced harmonic distortion, lower electromagnetic interference, and higher dc link voltages. However, it has some disadvantages such as increased number of components, complex pulsewidth modulation control method, and voltage-balancing problem. In this paper, a new topology with a reversing-voltage component is proposed to improve the multilevel performance by compensating the disadvantages mentioned. This topology requires fewer components compared to existing inverters (particularly in higher levels) and requires fewer carrier signals and gate drives. Therefore, the overall cost and complexity are greatly reduced particularly for higher output voltage levels. Finally, a prototype of the seven-level proposed topology is built and tested to show the performance of the inverter by experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes a three-phase current reconstruction technique with an online current offset compensation function for three-phase inverter applications utilizing only a single current sensor. In the proposed current sensing method, a phase current and a branch current are simultaneously measured twice in a switching period by using a single current sensor. After that, the current reconstruction algorithm is applied to obtain the three-phase current information. Compared to previous single current sensor strategies, in the proposed method, the sensor output is regularly sampled, and the dead zone is located near the boundary of the voltage vector space instead of near the origin and the borders of each sector. This boundary-neighbored dead zone makes the proposed method more attractive in extremely low modulation index cases because it avoids periodical dead zones which have been an issue in the existing methods. Moreover, the online compensation method for a current measurement offset makes it possible to achieve purely balanced three-phase current control without an offset component. The effectiveness of the proposed method has been verified through simulations and experiments by measuring and reconstructing three-phase currents under various conditions. [ABSTRACT FROM PUBLISHER]

A three-level inverter produces six active vectors, each of normalized magnitudes 1, 0.866, and 0.5, besides a zero vector. The vectors of relative length 0.5 are termed pivot vectors. The three nearest voltage vectors are usually used to synthesize the reference vector. In most continuous pulsewidth-modulation (PWM) schemes, the switching sequence begins from a pivot vector and ends with the same pivot vector. Thus, the pivot vector is applied twice in a subcycle or half-carrier cycle. This paper proposes and investigates alternative switching sequences, which use the pivot vector only once but employ one of the other two vectors twice within the subcycle. The total harmonic distortion (THD) in the fundamental line current pertaining to these novel sequences is studied theoretically as well as experimentally over the whole range of modulation. Compared with centered space vector PWM, two of the proposed sequences lead to reduced THD at high modulation indices at a given average switching frequency. [ABSTRACT FROM PUBLISHER]

This paper extends the Z-source concept to matrix converters and explores a family of Z-source matrix converters. Their principles and characteristics are analyzed, and a simplified voltage-fed Z-source matrix converter is used as an example to demonstrate its operation, voltage gain versus modulation index, PWM method, boost control, and implementation of the control. Both simulation and experimental results verify operation of the proposed Z-source matrix converter, analytical results, and control method. The Z-source converters can achieve buck and boost operation with reduced number of switches needed, therefore achieving low cost, high efficiency, and reliability, compared to the traditional matrix converters. [ABSTRACT FROM AUTHOR]

Common-mode voltage (CMV) is responsible for overvoltage stress to the winding insulation and bearing damage of an ac motor. High dv/dt of CMV raises leakage currents, which can cause serious problems such as motor damage and electromagnetic noise to the equipment installed near the converter. This paper proposes two modulation strategies for indirect matrix converters that substantially eliminate CMV. The first method is developed by using the suitable couple of nonzero space vectors instead of zero space vectors in the inverter stage. The maximum voltage transfer ratio of this method is unaffected and remains 0.866. The second one, which is useful for low-voltage operation, is approached by choosing the medium and the lowest positive line-to-line input voltages in the rectifier stage to generate the dc-link voltage and by placing suitable zero space vectors in the inverter stage. In the second method, the maximum voltage transfer ratio is 0.5. Both methods can mitigate the peak value to 42%. In addition, while the first method provides the same performance to the conventional method, the second method can reduce significantly the harmonic components of line-to-line output voltage. Simulation and experimental results are shown to verify the effectiveness of the proposed methods. [ABSTRACT FROM AUTHOR]

This paper presents first an overview of the well-known voltage and current dc-link converter topologies used to implement a three-phase PWM ac–ac converter system. Starting from the voltage source inverter and the current source rectifier, the basics of space vector modulation are summarized. Based on that, the topology of the indirect matrix converter (IMC) and its modulation are gradually developed from a voltage dc-link back-to-back converter by omitting the dc-link capacitor. In the next step, the topology of the conventional (direct) matrix converter (CMC) is introduced, and the relationship between the IMC and the CMCs is discussed in a figurative manner by investigating the switching states. Subsequently, three-phase ac–ac buck-type chopper circuits are considered as a special case of matrix converters (MCs), and a summary of extended MC topologies is provided, including three-level and hybrid MCs. Therewith, a common knowledge basis of the individual converter topologies is established. [ABSTRACT FROM PUBLISHER]

Instead of directly sampling the phase currents, a technique that adopts a single current sensor in the dc link to reconstruct three-phase currents has arisen. Through this approach, the cost of servo systems can be reduced and the reliability can be improved. However, the duration of an effective vector may be so short that the phase current cannot be measured reliably by the conventional space-vector pulsewidth modulation (PWM) algorithm. In this paper, a new phase-current reconstruction method, switching-state phase shift (SSPS), is proposed based on the PWM pattern modification. The modification is performed by applying phase shifts to the switching-state waveforms of the inverter. The algorithm can realize high-quality reconstruction to the phase current with less impacts on the output current ripples and switching losses. Moreover, it can maximize the linear-modulation region by saturation handling. Measurements on the permanent-magnet synchronous motor servo drives show that the SSPS can offer an attractive performance during both steady-state and dynamic operations in the phase-current reconstruction and regulation. [ABSTRACT FROM PUBLISHER]

In this paper, two space-vector-based pulsewidth modulation (PWM) (SVPWM) strategies named equal- and proportional-duty SVPWMs are described, which are used to synthesize a four-level waveform from an open-end winding configuration of an induction motor. Two isolated dc-link voltages, which are in the ratio of 2 : 1, are employed to achieve this objective. Both of these PWM strategies achieve the avoidance of overcharging of the dc-link capacitor of an inverter operating with lower dc-link voltage by its counterpart with higher dc-link voltage. Implementation of these PWM strategies requires only the instantaneous three-phase reference voltages, eliminating the need of sector identification or lookup tables. The numbers of samples per cycle for individual inverters are selected in such a way that the quarter-wave, half-wave, and three-phase symmetries are achieved for the dual-inverter drive despite unequal dc-link voltages for the constituent inverters. It is also shown that one of the two PWM techniques, called the proportional-duty SVPWM, results in a better spectral performance and lower switching power loss in the overall dual-inverter system compared to the equal-duty SVPWM. [ABSTRACT FROM PUBLISHER]

This paper presents a novel approach to analyze carrier-based discontinuous pulse width modulation (DPWM) method for multilevel inverters. The separation of the offset into the main and additional components shows the use for analyzing PWM control characteristics of multilevel inverters. The results are then applied to propose a novel minimized loss DPWM method by varying the offset depending on peak values of three-phase load currents. As results of avoiding commutations at high currents, the switching loss can be reduced. The proposed method is theoretically analyzed and verified by experimental results. [ABSTRACT FROM AUTHOR]

This paper presents direct digital technique-generalized discontinuous pulse width modulation (PWM)—a new implementation method for an optimal discontinuous PWM (DPWM) in terms of switching losses of the inverter on an embedded system. At each sampling period, an optimal choice is done in order to clamp one of the three half-bridges. Its advantages compared to classic ones (DPWM) are as follows: needless to know the load power factor, operational under steady-state and dynamic operating conditions, and low computation time. The proposed algorithm is then verified by simulation. Experimental results, based on a resistance–inductance load and a starter-generator application, are provided to show its effectiveness. [ABSTRACT FROM AUTHOR]

With regard to a five-level inverter comprising flying-capacitor asymmetric H-bridge, the impact on the capacitor voltage under conventional modulation approach is analyzed. Since it is sensitive to the fundamental period and the load current, it may introduce undesired low-order harmonics into the output voltage and may even break down the power switches due to the considerable fluctuation of the flying-capacitor voltage. Thus, this paper proposes a novel pulsewidth-modulation scheme with the positive and negative cross carriers, which controls the flying-capacitor voltage by utilizing the redundant switching states of the output voltages. Three modes of precharging the flying capacitor without extra equipments are presented. Moreover, the capacitance of the flying capacitor and the switching frequency of the power switches can be chosen according to the allowable fluctuation of the flying-capacitor voltage and the load current. In order to remove the overlapping of the level layers, the optimization of the line-to-line voltage waveform is proposed to synthesize the reference vector with the “nearest three-vector” approach. The theory is supported by the experimental results from the prototype. [ABSTRACT FROM AUTHOR]

Multilevel inverters introduce harmonics to the network besides their remarkable advantages. Total harmonic distortion (THD) is one of the most important indexes to evaluate the harmonic contents of waveforms. The conventional method of line-voltage THD calculation gives approximate answers, because high-order harmonics are ignored. In this paper, an analytical algebraic method based on formulating the line-voltage THD of multilevel inverters with unequal dc sources is presented. This method, which is general and applicable to each number of switching angles, is implemented to a five-level inverter with staircase waveform as a case study. The implementing process of this method can be easily repeated for each number of levels. The accuracy of the proposed method is illustrated in comparison with the approximate method. Some advantages of the extracted formulas of line-voltage THD are simplicity and rapidity in calculations, considering all harmonics and the possibility of finding optimal switching angles analytically. Experimental results are presented to validate the theory. [ABSTRACT FROM PUBLISHER]

The operation of switch-mode converters results in electromagnetic noise propagating throughout the power electronic system. Pulsewidth modulation (PWM) strategies with fixed switching frequency generate harmonics in the spectra of converter voltages and currents. Random PWM techniques allow the elimination of the harmonics, resulting in a continuous spectrum of noise, i.e., a spectrum retaining all frequency components. As a next step in advanced spectral shaping, a method presented in this paper produces spectral nulls at selected frequencies. This allows the carving of communication channels in the noise and the removal of spectral power at frequencies potentially harmful for the system. The theoretical analysis, computer simulations, implementation details, and experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper proposes a single-phase seven-level inverter for grid-connected photovoltaic systems, with a novel pulsewidth-modulated (PWM) control scheme. Three reference signals that are identical to each other with an offset that is equivalent to the amplitude of the triangular carrier signal were used to generate the PWM signals. The inverter is capable of producing seven levels of output-voltage levels (Vdc, 2Vdc/3, Vdc/3, 0, -Vdc, -2Vdc/3, -Vdc/3) from the dc supply voltage. A digital proportional–integral current-control algorithm was implemented in a TMS320F2812 DSP to keep the current injected into the grid sinusoidal. The proposed system was verified through simulation and implemented in a prototype. [ABSTRACT FROM AUTHOR]

Motivated by the method to analyze the impact of dead time in hard-switching converters, this paper, for the first time, analyzes the impact of zero-voltage notches on the outputs of soft-switching pulsewidth modulation (PWM) converters. It proves that the output distortion of soft-switching converters due to their deviation voltage is independent of the direction of their output current. Hence, their compensation strategies require no sensor to detect the current's direction, which is required by dead-time compensation methods in hard-switching converters. A simple yet effective compensation algorithm is presented for soft-switching converters. The analysis result and effectiveness of the proposed algorithm are experimentally verified via a three-phase inverter that represents an important class of converters. [ABSTRACT FROM AUTHOR]

Unipolar sinusoidal pulsewidth modulation (SPWM) full-bridge inverter brings high-frequency common-mode voltage, which restricts its application in transformerless photovoltaic grid-connected inverters. In order to solve this problem, an optimized full-bridge structure with two additional switches and a capacitor divider is proposed in this paper, which guarantees that a freewheeling path is clamped to half input voltage in the freewheeling period. Sequentially, the high-frequency common-mode voltage has been avoided in the unipolar SPWM full-bridge inverter, and the output current flows through only three switches in the power processing period. In addition, a clamping branch makes the voltage stress of the added switches be equal to half input voltage. The operation and clamping modes are analyzed, and the total losses of power device of several existing topologies and proposed topology are fairly calculated. Finally, the common-mode performance of these topologies is compared by a universal prototype inverter rated at 1 kW. [ABSTRACT FROM AUTHOR]

Half-cycle symmetry selective-harmonic-elimination pulsewidth-modulation (SHE-PWM) problems may have a large number of valid solutions, which are beneficial to the optimization design. This paper proposes a novel generalized formulation of half-cycle symmetry SHE-PWM problems for multilevel inverters. The advantages of the proposed formulation include simplicity in format, flexibility in PWMwaveforms, and a broad solution space. A method to obtain initial values for the SHE-PWM equations according to the reference modulation index M and the initial phase angle of output fundamental voltage is proposed and investigated thoroughly. Take a five-level inverter with M = 0.75 as an example; six sets of solutions for two typical initial phase angles of 0°? and 90°? are presented. Simulations and experiments are carried out. It is demonstrated that the experimental results agree well with simulated ones, which proves the validity and practicability of the new method proposed. [ABSTRACT FROM AUTHOR]