Search

In this paper, finite-set model-predictive control (FS-MPC) methodologies for a grid-connected three-level neutral-point-clamped converter are investigated. The proposed control strategies produce fixed switching frequency, maintaining all the advantages of predictive control such as fast dynamic response, inclusion of nonlinearities and restrictions, and multivariable control using a single control loop. The first of the proposed FS-MPC strategies is based on a multiobjective cost function, designed to regulate both the inverter currents and the balancing of the dc-link capacitor voltages. The second FS-MPC strategy is derived from the first one, and it is based on a cost function that regulates only the grid current, with the balancing of the capacitor voltages being realized by controlling the duty cycles of the redundant vectors. The proposed control systems are experimentally validated using a 5-kW prototype. The experimental results show a good performance for both strategies, in steady-state and transient response, with a total harmonic distortion lower than \text2\% for the currents supplied to the grid. [ABSTRACT FROM PUBLISHER]

In this paper, a dc-link voltage protection (DCVP) control method is proposed to address the dc-link overvoltage issue due to power backfeeding in a parallel uninterruptible power supply (UPS) system. The proposed control method is able to protect the inverter against the excessive dc-link voltage, which increases the system reliability and robustness. Moreover, a current sharing control strategy is proposed by online regulating the virtual resistance of each UPS module. The proposed current sharing control strategy is able to address the circulating fundamental and harmonic currents caused by the line impedance mismatching or power backfeeding issue in the UPS system. In addition, an improved consensus-based distributed controller is proposed to alleviate the overshoot issue during the transient process in voltage amplitude and frequency restoration. Finally, the feasibility of the proposed methods is verified by experimental results from the parallel UPS prototypes. [ABSTRACT FROM PUBLISHER]

The hybrid modulation strategy using both low-frequency square-wave modulation and high-frequency pulse-width modulation can extend the stable operating region of a cascaded H-bridge converter. However, it does not control accurately dc voltages of converter but balances them by charging or discharging dc capacitors based on the state of system, which could aggravate fluctuation of dc voltages. If cascaded H-bridge converter is used in photovoltaic field, the aggravated fluctuation on dc capacitor voltages will result in further losses in energy harvesting of solar cells. To address this issue, a modified hybrid modulation strategy is presented in this paper. When dc-bus measured voltages are close to their reference voltages, these H-bridges operate in a zero mode. Adding appropriate zero state can prevent grid current charging or discharging the dc capacitors whose voltages have already reached their control goals. Therefore, the proposed technique is capable of suppressing dc voltage fluctuation, and, thus, improving the output power of solar cells. Simulation and experimental results validate the effectiveness and feasibility of the proposed method. [ABSTRACT FROM PUBLISHER]

This paper presents an optimized topology of 3-$\phi$ , multilevel inverter (MLI) configuration for five or higher level operation with reduced switch count. The proposed solution consists of two basic units (BUs) of multilevel converter and a T-structured 3-level inverter (3-LI). Both BUs are equally shared by the three phases maintaining symmetry among the phases. Moreover, for a higher level operation of the proposed MLI, the modifications required are at two BUs only and not at three legs of the inverter. It further helps in reducing the requirement of extra components for higher level operation compared to the conventional solutions. Furthermore, the topology also has the benefits of reduced switching and conduction loss. An algorithm is also devised to generate the switching pulses for the BUs and the 3-LI, using a carrier-based space vector modulation technique. Presented topology is compared with other existing topologies to prove its advantage. All the details regarding the operating modes and pulse width modulation techniques employed for the proposed system are given and supported by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

Adding the auxiliary switches to the conventional H-bridge inverter is an effective way to eliminate the leakage current for transformerless PV systems, such as H5, H6, etc. Inspired by the newly developed embedded-switch H6 topology, a novel embedded-switch inverter (ESI) is proposed in this paper for three-phase transformerless PV systems. First, the operation principle and characteristics of the proposed ESI are analyzed. Second, the common-mode model of the three-phase ESI is established, based on which the main factors that affect the leakage current are discussed. The finding reveals that the switching states with conventional modulation strategy result in high-frequency common-mode voltage, which is the source of leakage current. In order to solve the problem, a new modulation strategy is presented for ESI to eliminate the high-frequency leakage current. Finally, the time-domain simulation and the experimental tests are carried out. The results verify the effectiveness of the proposed solution. [ABSTRACT FROM AUTHOR]

This paper aims to investigate a disturbance-rejection-based model predictive control (MPC) with two flexible modes (i.e., unconstrained mode and constrained mode) for three-phase inverters with an $LC$ filter. A disturbance observer (DOB) is designed to both simplify the prediction model and achieve the robustness against uncertain parameters. First, the unconstrained mode is designed with a simple horizon-one MPC control law to precisely regulate the output voltage in the steady state. Next, the constrained mode is designed with long-horizon MPC to quickly drive the system to the unconstrained mode by further optimizing the modulation stage. Also, the proposed MPC ensures the robustness and optimality in all operating modes. Especially, the overall closed-loop stability with DOB dynamics is proven by using Lyapunov function. Unlike other MPC methods, the long-horizon MPC in the constrained mode is specialized by finite switching sequences of the sector-based space vector modulation. Comparative studies with the conventional linear quadratic regulator are conducted on a prototype test bed with a TI TMS320F28335 DSP. Then, the proposed MPC method verifies fast dynamic response and advanced voltage regulation (i.e., small steady-state errors and low total harmonic distortion) under various load conditions and uncertain parameters. [ABSTRACT FROM AUTHOR]

In this paper, dual-buck structured single-stage buck–boost inverters that use power MOSFETs to achieve high efficiency are presented. The proposed inverters require fewer switches, and half of the switches have reduced current stresses. They have no shoot-through problem; therefore, high system reliability can be obtained. The dead-time in PWM signals can be minimized or eliminated, which improving the quality of the output ac voltages and increasing the efficiency. In the proposed inverters, MOSFETs can be used without reverse-recovery issues of their body diodes to boost the efficiency and increase the switching frequency. To further improve the efficiency and stability of the proposed single-phase inverter, PWM strategies combining high- and low-frequency modulation are presented. A hardware prototype of the single-phase inverter was built and tested using resistive, inductive, and nonlinear loads. Experimental results for a 300-W prototype inverter show a 97.4% peak efficiency with a 25 kHz switching frequency. [ABSTRACT FROM AUTHOR]

The parallel three-phase grid-connected converters sharing dc and ac bus can increase the system power level effectively. However, the zero sequence circulating current (ZSCC) will occur inevitably under space vector pulse width modulation or discontinuous pulse width modulation (DPWM). In this paper, the mechanism and the mathematical model of ZSCC are studied. Then, a hybrid PWM (HPWM) strategy is proposed to suppress the ZSCC based on the same zero sequence voltage injected, which is dependent on the common grid information. The dc voltage utilization of HPWM can be extended compared with sinusoidal PWM (SPWM). The number of parallel modules can be infinity theoretically by using HPWM. It is noted that there is no internal commutation among modules (expect the dq current reference). Finally, the feasibility and the effectiveness of the proposed method are verified by experiments. [ABSTRACT FROM AUTHOR]

The battery energy-stored quasi-Z-source (BES-qZS)-based photovoltaic (PV) power generation system combines advantages of the qZS inverter and the battery energy storage system. However, the second-harmonic ( \text2\omega ) power ripple degrades the system's performance and affects the system's design. An accurate model to analyze the \text2\omega ripple is very important. The existing models did not consider the battery, or assumed a symmetric qZS network with $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$, which limits the design freedom and causes oversized impedance parameters. This paper proposes a comprehensive model for the single-phase BES-qZS-PV inverter system, where the battery is considered and there is no restriction of $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$ . Based on the built model, a BES-qZS impedance design method is proposed to mitigate the \text2\omega ripple with asymmetric qZS network. Simulation and experimental results verify the proposed \text2\omega ripple model and impedance design method. [ABSTRACT FROM AUTHOR]

Traditional model predictive control cost functions, when utilizing long prediction horizons ( $N\geq 10$) in power inverter applications, have demonstrated harmonic performances approaching that of schemes based on offline-generated optimal pulse patterns. However, long prediction horizons often prohibitively increase computational load. A different approach to maximizing harmonic performance is taken in this paper. It is shown that shaping the output voltage spectra using a simple feedback mechanism can significantly reduce the length of the required prediction horizon, facilitating a feasible computational load. When a short-horizon cost function is augmented by the feedback mechanism an excellent tradeoff between harmonic performance and switching loss is achieved, even with a prediction horizon of one. It is also shown that the feedback mechanism can be used to improve input reference tracking. Experimental verification of the proposed modulator is performed on a two-level three-phase inverter. [ABSTRACT FROM AUTHOR]

Several applications such as power supplies for electric precipitators, ozone generation, partial discharge, etc., require ac superimposed dc (ACsDC) voltage supply. Most of such applications use intransigent systems for producing ACsDC voltages. In this paper, three different kinds of flexible power electronic converters are proposed for producing ACsDC voltages. These converters have two power conversion stages: input and output. In the input stage, two isolated dc voltages are obtained by using an isolated three-port dc–dc converter or two isolated two-port dc–dc converters. In the output stage, one of the input-stage dc voltages is used to generate an ac voltage and the obtained ac voltage is added to the remaining input-stage dc voltage to obtain an ACsDC voltage. Based on the converters used in the input stage, the proposed ACsDC converters are named as a dual active bridge (DAB) converter-based ACsDC converter (DAB-ACsDC), triple port active bridge (TAB) converter-based ACsDC converter (TAB-ACsDC), and dual transformer-based asymmetrical triple port active bridge (DT-ATAB) converter-based ACsDC converter (DTATAB-ACsDC). A detailed analysis of these ACsDC converters and their verifications using simulations and experimental studies are presented, which depict that the proposed converters can be used effectively for producing ACsDC voltages. [ABSTRACT FROM AUTHOR]

Compared with multilevel space vector modulation, level-shifted multicarrier sinusoidal pulsewidth modulation (SPWM) for nested neutral point-clamped (NNPC) inverters requires much less calculations and implementation efforts, but the existing conventional SPWM cannot suppress the severe flying-capacitor (FC) voltage ripples under low output-frequency conditions. In order to solve this problem, a multicarrier-based PWM strategy with complete voltage balance control (VBC) capacity is proposed in this paper. For NNPC inverters operating under low output-frequency conditions, two preprocessing steps, the zero-sequence injection and the modulation-signal rearrangement, are proposed before the comparisons between level-shifted carriers and modulating signals. These preprocessing steps make the average currents flowing through FCs zero, which is beneficial to greatly reduce the FC voltage ripples under low output-frequency conditions. Together with additional VBC, the proposed modulation can assure the FC voltages balanced under the entire output-frequency conditions. Principles and implementation processes of proposed modulation techniques and VBC methodsare elaborated in detail and compared with conventional modulation methods. Both simulation results from a 5-MVA system and experimental results based on a 5-kVA platform are presented to verify the effectiveness. [ABSTRACT FROM AUTHOR]

This paper proposes a high-efficiency two-stage three-level grid-connected photovoltaic (PV) inverter. The proposed two-stage inverter comprises a three-level step-up converter and a three-level inverter. The three-level step-up converter not only improves the power-conversion efficiency by lowering the voltage stress but also guarantees the balancing of the dc-link capacitor voltages using a simple control algorithm; it also enables the proposed inverter to satisfy the VDE 0126-1-1 standard of leakage current. The three-level inverter minimizes the overall power losses with zero reverse-recovery loss. Furthermore, it reduces harmonic distortion, the voltage ratings of the semiconductor device, and the electromagnetic interference by using a three-level circuit configuration; it also enables the use of small and low-cost filters. To control the grid current effectively, we have used a feed-forward nominal voltage compensator with a mode selector; this compensator improves the control environment by presetting the operating point. The proposed high-efficiency two-stage three-level grid-connected PV inverter overcomes the low efficiency problem of conventional two-stage inverters, and it provides high-power quality with maximum efficiency of 97.4%. Using a 3-kW prototype of the inverter, we have evaluated the performance of the model and proved its feasibility. [ABSTRACT FROM PUBLISHER]

This paper proposes a family of novel flying capacitor transformerless inverters for single-phase photovoltaic (PV) systems. Each of the new topologies proposed is based on a flying capacitor principle and requires only four power switches and/or diodes, one capacitor, and a small filter at the output stage. A simple unipolar sinusoidal pulse width modulation technique is used to modulate the inverter to minimize the switching loss, output current ripple, and the filter requirements. In general, the main advantages of the new inverter topologies are: 1) the negative polarity of the PV is directly connected to the grid, and therefore, no leakage current; 2) reactive power compensation capability; and 3) the output ac voltage peak is equal to the input dc voltage (unlike neutral-point-clamped and derivative topologies, which requires twice the magnitude of the peak ac voltage). A complete description of the operating principle with modulation techniques, design guidelines, and comprehensive comparisons is presented to reveal the properties and limitations of each topology in detail. Finally, experimental results of 1-kVA prototypes are presented to prove the concept and theoretical analysis of the proposed inverter family for practical applications. [ABSTRACT FROM PUBLISHER]

This paper proposes a repetitive controller with phase-lead compensation for an unfolding-type Cuk continuous conduction mode (CCM) inverter operating in the CCM. The Cuk CCM inverter features medium power capacity, step up/down ability, and low input/output current ripples, so it is well suited to distributed power generation systems. To achieve accurate tracking of the reference output current, we make the use of the repetitive controller coupled with a conventional proportional-integral controller and a nominal duty ratio. In developing the proposed controller, we use the average model of the Cuk CCM inverter in the grid-connected case. The two right-half plane (RHP) zeros in the transfer function of the Cuk CCM inverter cause phase lag of the closed-loop system; to compensate for the phase lag, we implement a phase-lead compensation algorithm in the repetitive control scheme. We also provide detailed and practical design guidelines of the control parameters to develop a stable Cuk CCM inverter. Experimental tests using a 500-W Cuk CCM inverter demonstrate the desirable performance of the proposed control approach. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel 49-level stacked inverter topology for drives. The 49 levels are achieved by stacking three 17-level inverters. Each of the 17-level inverter is developed by cascading a flying capacitor (FC) inverter with three capacitor-fed H-bridges. The device count can be reduced by making the FC and the three cascaded H-bridges common to the dc link in each phase using selector switches in between them. The selector switches need to operate at fundamental frequency only. Also, the devices need to block very low voltages. Hence, MOSFETs can be used. This topology requires three dc sources, each of V\text{dc} /6 only, which can be replaced with stacked batteries for electric vehicle applications. The reduction in the dc voltage requirement is achieved by using a normal symmetric six-phase induction motor with parallel connection of the opposite phase windings. All the floating capacitors in the topology can be balanced irrespective of any modulation index or load power factor. Due to the high number of voltage levels, nearest level control can be used instead of pulse width modulation, which reduces the switching losses. The $dv/dt$ during the inverter operation is also less. Detailed experimental results at different speeds of operation and during transients ensure that the novel topology can be a viable option for high-power adjustable speed drives. [ABSTRACT FROM PUBLISHER]

In this paper, a new nonisolated high-voltage-gain boost converter is proposed. The proposed converter is constructed by adding an additional inductor to a conventional three-level-boost (TLB) converter. When compared with the conventional boost and TLB converters, the proposed converter can achieve higher voltage conversion ratio with reduced voltage and current stresses in the switches. In particular, the proposed converter can reduce the losses of active devices by reducing the current of the switch compared to conventional converters, thus, can achieve high efficiency. In addition, the proposed converter automatically balances the output voltages for an unbalanced load without the need for any additional control strategy or auxiliary circuit. A 2-kW prototype converter was built and tested to verify performances of the proposed converter. [ABSTRACT FROM PUBLISHER]

Transformerless cascaded H-bridge inverters have the advantages of low cost and high efficiency in low-power applications. However, the leakage currents resulting from the parasitic capacitors may increase system losses, electromagnetic interference, and safety concerns. To reduce the leakage current, this paper first establishes the equivalent common-mode circuit of the inverter with the parasitic capacitance and analyzes the characteristics of leakage current in the symmetrical and asymmetrical filter inductance circuit, respectively. The analysis shows that the traditional phase disposition pulse width modulation or phase-shift pulse width modulation cannot solve the leakage current issues, but modifying the modulation methods can eliminate the system leakage current in the symmetrical circuit, and it has a little effect in the asymmetrical circuit. For this reason, a modified phase disposition pulse width modulation for the symmetrical circuit, which can eliminate the leakage current effectively with simple implementation, is proposed. Simulation and experimental results are reported, along with evaluation and comparison results, against a conventional carrier-based pulse width modulation method. [ABSTRACT FROM PUBLISHER]

In this paper, a fault-tolerant multiphase multilevel inverter (MPMLI) configuration is proposed based on the dual inverter concept. This configuration helps to improve the performance of pole–phase modulated multiphase induction motor (PPMMIM) drive in both normal and switch failure conditions. Comparing to the existing multilevel inverter topologies for multiphase induction motor (MIM) drives, the proposed MPMLI configuration requires less number of dc sources and power electronic devices. The proposed MPMLI configuration is able to sustain under various faulty conditions, which can improve the reliability of the system. In addition, dc-link utilization (DLU) in low-pole mode is improved by using space vector pulsewidth modulation (SVPWM). In high-pole mode, carrier-phase-shifted 3-Φ SVPWM is used for reducing the torque ripple. This MPMLI configuration produces a multilevel voltage profile across the effective phase in 3-phase 12-pole mode. By maintaining the V/f ratio constant, the proposed MPMLI-fed MIM drive facilitates a wide range of load torque with half of the rated speed in faulty condition. This advantage makes it suitable for traction and electric vehicle applications where reliability and wide range of torque–speed are the major concerns. The performance of proposed MPMLI-fed 5 hp, 9-φ PPMMIM drive is simulated by finite-element method (FEM) in ANSYS Maxwell 2-D and experimentally verified by laboratory prototype under normal and faulty conditions. [ABSTRACT FROM PUBLISHER]

In this paper, a new carrier-based pulse width modulation (PWM) strategy providing common-mode voltage (CMV) elimination and reduced current ripple in a three-level neutral-point-clamped inverter is introduced. The employed switching sequences are made up of the three zero CMV (ZCMV) vectors, and one among the three vec-tors is applied at two ends of a half-carrier cycle. The output current ripple characteristics pertaining to those switching sequences are investigated. In a carrier cycle, the root-mean-square current ripple minimization is analyzed and an optimal sequence is derived accordingly. The presented PWM scheme results in a considerably reduced current harmonic distortion in a wide modulation region as compared to the two existing ZCMV schemes on the same average switching frequency. Also, an implementation of sawtooth-carrier-based PWM patterns is proposed for further improvement of the harmonic performance. The algorithm requires small computational burden and is straightforward for an online implementation. Simulation and experimental results are both provided to validate the good performance of the proposed PWM method. [ABSTRACT FROM PUBLISHER]

In this paper, an improved transformerless single-phase single-stage grid-tied flying inductor inverter is presented. The negative terminal of the photovoltaic (PV) array is grounded in the improved topology, which increases reliability and suppresses the leakage current. The proposed topology has buck–boost capability without increasing the number of required components and has a high efficiency. An improved control algorithm for proper operation of the proposed topology which decreases switching losses has been investigated. Moreover, a perturbation and observation maximum power point tracking (MPPT) algorithm has been adapted to the proposed inverter, which does not utilize proportional–integral (PI) controllers, for the purpose of the MPPT. Furthermore, a design procedure of the passive elements of the converter based on the corresponding operating has been demonstrated. Simulation in MATLAB Simulink plus an experimental prototype is developed to reconfirm the designed results. Finally, a comparison study has been investigated for better clarification of the advantages and disadvantages of the proposed inverter. [ABSTRACT FROM PUBLISHER]

For three-phase dual-output dc–ac conversion systems, the nine-switch inverter is one of the most versatile available topologies. Despite some disadvantages, recent studies show that the nine-switch inverter achieves efficiency values equivalent to or higher than its 12-switch counterpart, when operating in certain ranges of the modulation index and displacement angles. The use of proper pulse width modulation techniques is able to increase the efficiency even more, as well as to equalize the loss distribution among the switches, favoring an effective and low-cost thermal design. The available pulse width modulation techniques are complex and do not explore the full capacity of the nine-switch inverter to reduce its losses. For this reason, this paper proposes an unrestricted generalized scalar pulse width modulation for nine-switch inverters. Based on this new generalization, a current peak tracking technique is also proposed, achieving small average number of switchings and the highest overall efficiency when compared with other techniques, likewise a more balanced loss distribution among the switches. Experimental results are carried out to demonstrate the validity of the new generalization and the effectiveness of the proposed technique in reducing the switching losses. [ABSTRACT FROM PUBLISHER]

To achieve precise voltage value for modern model-based motor control strategies, an accurate voltage distortion compensation method for voltage source inverters is proposed in this paper. The voltage distortion principles of a mosfet-based inverter and an IGBT-based inverter are analyzed and compared. A graphical solution of compensating voltage error is proposed, all the voltage distortion factors are considered. A current observer is designed to overcome time delay, achieve precise current in each switching period for compensation. The proposed method is of high precision, intuitive, and easy to implement. The effectiveness of the proposed method is verified by experiments. [ABSTRACT FROM PUBLISHER]

High di/dt and dv/dt of SiC MOSFET cause a considerable amount of overshoot in device voltage and current during switching transients in the presence of inverter layout parasitic inductance and load parasitic capacitance. The excessive overshoots in device voltage and current cause failure of the device. Moreover, these uncontrolled overshoots increase the switching loss in the inverter. It is difficult to reduce parasitic inductance beyond a certain point. This paper proposes an active gate driving technique, which allows inverter to operate with moderate amount of layout parasitic inductance and load parasitic capacitance. The proposed technique dramatically reduces switching loss of the SiC MOSFET with the help of existing parasitic elements. The proposed switching loss reduction technique is termed as quasi zero switching. The developed active gate driver has been tested in a double pulse test setup and a 10 kW two-level voltage source inverter driving an induction motor. [ABSTRACT FROM PUBLISHER]

In this paper, a switching loss-free (SLF) concept for the first six-switches H-bridge inverter (H6-I) topology is proposed. SLF means that its switches are able to operate with soft turn-on and turn-off transitions. In order to implement the SLF goal, a new resonance-trajectory is proposed. Compared with the zero-current-transition H6-I (ZCT-H6-I) topology published in previous literature, the proposed resonance-trajectory can precisely compensate for losses of resonant tanks every switching period. With this intention, an implementing circuit is structured based on the H6-I topology, and its detailed operation principle and performance characteristics are analyzed. As a result, all active switches of the new circuit are switched under zero-current turn-on and zero-current turn-off conditions. Also, the reverse recovery problem of freewheeling diodes is alleviated owing to the zero-current turn-off property of diodes. The SLF target is realized in theory. Finally, experimental results from a 1 kW prototype at 50 kHz switching frequency are provided to verify the effectiveness of the proposed SLF concept in practice. Specifically, the conversion efficiency of the new circuit is over 95% in a wide load range, and there is roughly a 1.5% efficiency improvement compared with the hard-switching H6-I topology. [ABSTRACT FROM PUBLISHER]

As more widebandgap (WBG) devices are becoming commercially available, it is beneficial to use WBG device to increase the switching frequency in order to reduce the passive components. For quasi-Z-Source (qZS) grid-tied inverters, the reduction of passive components raises stability concerns as the coupling effect between the dc side and ac side of qZS inverter will increase. In this paper, the coupling effect between qZS impedance network and the output filter is analyzed by modeling both dc and ac sides. Analysis reveals the resonant characteristic of the qZS inverter. Controller parameter boundaries are derived, and a design method to improve stability is then proposed. Case studies for a 2.5-kW 10-kHz Si-based qZS inverter and a 1-kW 100-kHz GaN-based qZS inverter are presented. Circuit simulations and experimental verifications results are provided to assess analysis and the control design. [ABSTRACT FROM PUBLISHER]

Silicon carbide (SiC) MOSFETs and gallium nitride (GaN) high-electron mobility transistors are perceived as future replacements for Si IGBTs and MOSFETs in medium- and low-voltage drives due to their low conduction and switching losses. However, it is widely believed that the already significant conducted common-mode (CM) electromagnetic interference (EMI) emission of motor drives will be further exacerbated by the high-speed switching operation of these new devices. Hence, this paper investigates and quantifies the increase in the conducted CM EMI emission of a pulse width modulation inverter-based motor drive when SiC and GaN devices are adopted. Through an analytical approach, the results reveal that the influence of dv/dt on the conducted CM emission is generally limited. On the other hand, the influence of switching frequency is more significant. Lab tests are also conducted to verify the analysis. [ABSTRACT FROM PUBLISHER]

The cascaded H-bridge converter has been widely used in industry. The ability of dealing with unequal power generation among dc links is necessarily required in many applications, such as large-scale photovoltaic power plants and electric vehicles. In this paper, a novel dc-power control method (PCM) is proposed to keep the ac-current balance and maintain power generation ratios of each dc source at their expected values. A simplified modulation strategy is introduced to implement the proposed method, in which the duration times are modified directly by the correction value derived from the PCM method. To calculate and adjust the power generation ratios, a method based on first-in first-out (FIFO) data queue is utilized. The limitation and ranges of power generation ratio are analyzed in detail. DC power per phase can be controlled accurately by the proposed method in variable-frequency condition, even under larger power generation ratios. Results obtained from simulations and experiments are presented to verify the feasibilities and superiorities of the proposed method. [ABSTRACT FROM PUBLISHER]

Existing integrated chargers are configured to charge from single- or three-phase ac networks. With the rapid emergence of dc grids, there is growing interest in the development of high-efficiency low-cost integrated chargers interfaced with dc power outlets. This paper introduces a new integrated charger offering electric vehicle fast charging from emerging dc distribution networks. In absence of a dc grid, the charger can alternatively be fed from a simple uncontrolled rectifier. The proposed charger leverages the dual-inverter topology previously developed for high-speed drive applications. By connecting the charger inlet to the differential ends of the traction inverters, charging is enabled for a wide battery voltage range previously unattainable using an integrated charger based on the single traction drive. An 11-kW experimental setup demonstrates rapid charging using constant current control and energy balancing of dual storage media. To minimize the harmonic impact of the charger on the dc distribution network, a combination of complementary and interleaved switching methods is demonstrated. [ABSTRACT FROM PUBLISHER]

The impedance-source network converter, utilizing a unique LC network and previously forbidden shoot-through states, provides the ability to buck and boost the input voltage in a single stage. However, the inrush shoot-through current (STC) in startup or transient process might cause undesired current stresses on converter devices. This paper focuses on the STC sensing for an effective inrush current limitation by the combined current sensing technique in the quasi-Z-source inverter. STC and phase currents for the inverter control strategy are obtained simultaneously. No extra hardware is needed and the effects of current sensor bandwidth and duty cycle on the sensing accuracy are analyzed mathematically. The voltage spike gets avoided by integrating the stray inductance into the impedance network. Finally, an STC control loop based on proposed method are embedded in the field-oriented control strategy. The inrush STC and the device current stress in the transient process get suppressed. Simulation and experimental results from a quasi-Z-source inverter validate the feasibility of the proposed methods. [ABSTRACT FROM PUBLISHER]

Photovoltaic (PV) microinverters dispense with the line frequency transformer, however at the cost of system grounding and ground leakage current problems. These have been erstwhile resolved by the topologies derived from buck, boost, buck–boost, Zeta, Watkins–Johnson, and Ćuk converters, or combinations of these. The Ćuk derived inverters, employing second-order input and output filters, offer the most efficient, lightweight, and economical solution in the class. This paper presents design and detailed operation of a Ćuk derived, common-ground PV microinverter in continuous conduction mode operation. The inverter is shown to be compatible with both linear and nonlinear loads, in stand-alone and grid-connected modes of operation. Optimal design rules of passive components are rigorously derived to ensure attenuation of input voltage ripples arising from the twin effects of switching and double-frequency output power oscillation. Additionally, the design rules also incorporate considerations of efficiency maximization and some aspects of easing control complexity. Inverter performance is experimentally validated with a 300 VA, 110 V, and 50/60 Hz laboratory prototype. [ABSTRACT FROM PUBLISHER]

Grid-connected power conversion systems for renewable energy sources must fulfill several requirements, e.g., the high efficiency, the reduced cost and complexity, and, quite often, the boost capabilities that is usually achieved using a front-end dc–dc boost converter before the inversion stage, leading to a two-stage architecture. Meanwhile, single-stage power conversion systems, which perform the boosting operation within the inversion one, offer some potential advantages, in terms of reducing the complexity and the volume of the whole system. Among several proposed options, the split-source inverter (SSI) has been recently proposed by Abdelhakim et al. as an alternative option with some interesting features to the commonly used Z-source inverter. Taking into account that the SSI is controlled by a single parameter, i.e., its dc and ac sides are controlled by the modulation index, it is of paramount importance to investigate its control scheme in grid-connected mode, which has never been studied yet. Hence, this paper models the SSI dc side and proposes a modified modulation scheme combined with the commonly used synchronous reference frame control technique to achieve a decoupled control scheme of the SSI in grid-connected mode, i.e., the dc and the ac sides of the SSI can be controlled independently, which is convenient for many applications. The introduced control scheme is analyzed and simulated using a MATLAB/Simulink model, where a reduced scale 1-kVA grid-connected SSI is designed and simulated for the sake of experimental validation. Finally, the designed system is implemented experimentally to validate and verify the reported analysis and simulations. [ABSTRACT FROM PUBLISHER]

This paper presents the mathematical and harmonic analyses of output phase voltages of three-phase voltage source inverters which employ a hybrid two-dimensional–threedimensional (2-D–3-D) space vector modulation (SVM) voltage control algorithm. The explicit time-domain representation of the harmonic components in addition to the total harmonic distortion (THD) of the output phase voltages is given in terms of system and control parameters. This paper also investigates the harmonic characteristics and THD performance against the linearity of the modulation region which helps in the harmonic performance and design studies of such inverters employing the hybrid 2-D–3-D SVM. The fundamental component of the output voltages follows the reference with lower THD in the linear modulation region rather than the overmodulation region. Experimental results are used to validate these analyses as well as the effectiveness of the hybrid 2-D–3-D SVM algorithm for generating balanced and low THD phase voltages. [ABSTRACT FROM PUBLISHER]

This paper presents the design and implementation of a simple neutral point potential (NPP) regulator for a three-level diode-clamped inverter employing a sine-triangle regulator in conjunction with a closed-loop controller with reduced switching losses. The regulator principle is based on adding a continuous variable offset voltage which regulates the midpoint potential of the dc bus. The novelty of the proposed NPP regulator is in the determination of the magnitude of variable offset voltage based upon the average value, peak-to-peak amplitude, total harmonic distortions, and third harmonic content in NPP. Aside from maintaining dc-bus voltage balance, the proposed regulator leads to a significant reduction in the voltage distortion at the NP, resulting in the reduction of the required dc-bus capacitance. It also reduces the switching losses of the inverter by inserting the “no-switching” zone within each half cycle of the fundamental voltage wave. Analytical, computer simulation, and experimental results verifying the approach are presented in this paper for various load power factor angles. [ABSTRACT FROM AUTHOR]

The Z-source inverter (ZSI) employs an LC impedance network between the main inverter bridge and the power source. The unique feature of the ZSI is that it can operate either in buck or boost mode with a wide range of obtainable output voltages from a given input voltage. This topology also exhibits better electromagnetic-interference noise immunity when compared to a traditional voltage-source inverter (VSI). However, the LC impedance network of ZSI significantly increases the size and cost of the power converter and can make it unsuitable for low-power applications. This paper proposes a novel topology called switched boost inverter (SBI) which exhibits similar advantages of ZSI with lower number of passive components and more active components compared to ZSI. The steady-state and small-signal analyses of SBI, along with its pulsewidth modulation (PWM) control strategies, have been discussed in this paper. This paper also presents a comparison of SBI and ZSI with the same input and output parameters. The theoretical analysis given in this paper has been validated using a laboratory prototype of SBI, and the experimental results are presented for verification. The experimental harmonic spectrum of the inverter's output voltage with the proposed PWM technique is also plotted and compared with that of a traditional VSI. All the experimental results show good correlation between theory and experiments. [ABSTRACT FROM PUBLISHER]

Neutral-point (NP)-clamped three-level inverter, which is a widely used topology of multilevel converters, suffers from the NP voltage drift as its main technical drawback. The nearest-three-virtual-vector (\NTV^2) modulation method can control the NP voltage balance for any load over the full range of inverter output voltage. However, compared with the nearest-three-vector (NTV) modulation method, \NTV^2 increases the switching frequency. This paper combines \NTV^2 with NTV, and the two methods are used alternately in a fundamental cycle. The duty-cycle coefficients of the redundant small vectors are analyzed to explore the intervals where NTV can control the NP voltage balance in a fundamental cycle. The proportional parameter, which represents the combination of the two methods in hybrid space vector pulsewidth modulation, can be selected to achieve a high-performance NP balance control and low switching frequency. The steady- and transient-state behaviors of the proposed strategy are analyzed in this paper. The experimental results verify the validity of the proposed strategy. [ABSTRACT FROM PUBLISHER]

A dual two-level voltage source inverter (VSI) can synthesize a three-level voltage space vector employing an open-end winding induction motor. Space-vector-based pulsewidth modulation (PWM) variants for this dual VSI are proposed in this paper that offer the dual advantage of limiting the switching power loss to a single VSI at all instants and also reducing the switching commutations in the dual VSI by 50%. The influence of different error volt seconds (affected with different PWM variants) on the motor phase current in the dual VSI is critically analyzed. To this end, two analytical approaches (one using error-voltage trajectory information and the other using switching state information of the dual VSI) are also proposed in this paper to predict the current trajectory and the ripple content in the drive system. Expressions for rms ripple current are developed with different PWM variants. The efficacy of the proposed analytical approaches to predict the current trajectory and the ripple content is confirmed from the experimental results. All the PWM variants are first simulated using MATLAB and verified experimentally by conducting tests on a three-phase open-end winding induction motor drive controlled with volts per hertz control. The implementation of the PWM algorithms only requires instantaneous magnitudes of three-phase reference voltages and completely avoids the sector identification and lookup tables. [ABSTRACT FROM PUBLISHER]

In recent years, high photovoltaic array voltage up to 1000 V and transformerless grid-tied inverter have been increasingly researched and applied to elevate the inverter and the dc power collection efficiency. With the same reasons, a three-level neutral point clamped (3L-NPC) inverter featuring low power device voltage stress and low leakage current becomes increasingly attractive. In this paper, the operation and the features of a novel grid-tied 3L-NPC are presented. The proposed topology is a derivative of the three-level stacked neutral point clamped (3L-SNPC) structure. However, compared with the conventional 3L-SNPC and its pulse width modulation (PWM) strategy, the new topology with novel PWM strategy features completely inactive intrinsic body diodes. Furthermore, only two outer power devices are working with switching frequency, while the other four Insulated Gate Bipolar Transistors (IGBTs) are actually with the grid frequency. Therefore, the relatively high switching frequency is selected to reduce the inverter output filter inductance. A hybrid CoolMosfet and IGBT power module configuration is also proposed based on the new PWM strategy. The calculation shows that the total power device losses are reduced. The experimental results are illustrated in this paper to confirm the operation of the proposed topology and controller. [ABSTRACT FROM PUBLISHER]

A generalized space-vector-based spread spectrum modulation scheme for multilevel inverters is proposed in this paper. The proposed scheme uses the principle of sigma–delta modulation as applied to analog-to-digital converters (ADCs), based on the view that a multilevel converter could be interpreted as an oversampling ADC. The principle of vector quantization is utilized for quantizing the instantaneous reference voltage space vector in the proposed space-vector-based sigma–delta converter. The switching vectors of the inverter are naturally selected without sector identification, ensuring optimum switching sequence under all conditions including the overmodulation region. As the sigma–delta converter results in a randomly varying switching frequency, the proposed scheme has spread spectrum characteristics. To avoid fractional arithmetic, a 60 ^\circ coordinate system is used to represent the space vector in this paper. The proposed scheme can be used for any general n-level inverter, and experimental results are presented for four-, five-, and six-level inverters, driving a 2-hp three-phase induction motor in an open-end winding configuration. The experimental results of the proposed scheme are compared with the space-vector pulsewidth modulation (PWM) scheme and random PWM scheme. [ABSTRACT FROM PUBLISHER]

In the paper by Chen et al. (IEEE Trans. Ind. Electron., vol. 66, no. 4, pp. 2837–2846, Apr. 2019), the authors proposed two fault-tolerant control strategies for T-type three-level inverters considering neutral-point (NP) voltage oscillations. However, some basic problems are worth being discussed about the proposed fault-tolerant control methods. This letter presents some comments and results concerning the paper by Chen et al. [ABSTRACT FROM AUTHOR]

This paper presents a capacitor-clamped three-level inverter-based supercapacitor direct integration scheme for wind energy conversion systems. The idea is to increase the capacitance of clamping capacitors with the use of supercapacitors and allow their voltage to vary within a defined range. Even though this unique approach eliminates the need of interfacing dc–dc converters for supercapacitors, the variable voltage operation brings about several challenges. The uneven distribution of space vectors is the major modulation challenge. A space vector modulation method is proposed in this paper to address this issue and to generate undistorted currents even in the presence of dynamic changes in supercapacitor voltages. A supercapacitor voltage equalization algorithm is also presented. Moreover, control strategies of the proposed system are discussed in detail. Simulation and experimental results are presented to verify the efficacy of the proposed system in suppressing short-term wind power fluctuations. [ABSTRACT FROM PUBLISHER]

In this paper, an immune algorithm (IA) is developed for optimization of the harmonic performance of a three-phase inverter under the space-vector pulsewidth-modulation (SVPWM) control strategy. The presented algorithm employs the immune approach as the search method for finding the best optimal control vectors and action time of the three-phase inverter. As a result, the optimal control vectors and action time are calculated to minimize the objective function of the weighted total harmonic distortion of the output voltage waveforms. In addition, an experimental platform based on DSP and field-programmable gate array is built. This paper provides a detailed performance analysis of the method with comparison to the conventional SVPWM. The simulation and experimental results verify the superiority of the best control sequences generated by IA compared with the existing conventional control strategies. [ABSTRACT FROM PUBLISHER]

A new pulse width modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is developed and presented in this paper. The proposed PWM scheme not only takes advantage of the special properties available in NPC inverters, but also reduces the switching loss of the inverter along with an inherent neutral point (NP) voltage control. Based on a circuit-level decoupling concept, the NPC inverter can be decoupled into two three-level Buck converters in every defined operating section, and thereby the controller design can be simplified. The salient features of the proposed scheme, as compared with the existing carrier-based DPWM strategies, are: 1) its reduced computational processing time, 2) its capability to balance the dc-link voltage without any additional control, and 3) its reduced complexity, e.g., only one carrier wave needed for pulse width modulating. Same as a space-vector modulation, the maximum modulation index, 1.1547, can be attainable by the proposed scheme. Moreover, compared to conventional continuous sinusoidal PWM, using this technique proposed here, the switching losses of the devices can be reduced by one third. In order to explain the operation of this topology properly, the decoupling principle including the driving signal synthesis and the NP potential variation are analyzed in detail in this paper. Finally, the viability and performance of the proposed modulation scheme are shown through simulation and experimental results in a laboratory prototype. [ABSTRACT FROM PUBLISHER]

A new approach for modulation of an 11-level cascade multilevel inverter using selective harmonic elimination is presented in this paper. The dc sources feeding the multilevel inverter are considered to be varying in time, and the switching angles are adapted to the dc source variation. This method uses genetic algorithms to obtain switching angles offline for different dc source values. Then, artificial neural networks are used to determine the switching angles that correspond to the real-time values of the dc sources for each phase. This implies that each one of the dc sources of this topology can have different values at any time, but the output fundamental voltage will stay constant and the harmonic content will still meet the specifications. The modulating switching angles are updated at each cycle of the output fundamental voltage. This paper gives details on the method in addition to simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper discusses the implementation of level-shifted and phase-shifted carrier-based modulation methods, in conjunction with a multiphase open-end winding drive topology. The considered drive is supplied using two five-phase two-level voltage source inverters (VSIs), with input provided from two isolated supplies of equal dc voltages. The topology is known to yield the same space-vector pattern as a corresponding three-level inverter in single-sided supply mode. It is shown in this paper that, with the application of a simple logic, the same phase voltage waveforms result as those obtainable with the appropriate carrier-based modulation scheme applied to the three-level VSI in single-sided supply mode. While the outcomes of the modulation techniques are the same, the open-end winding topology offers certain advantages, such as modularity and absence of capacitor voltage balancing requirements. The analysis is conducted for selected modulation methods using voltage and current waveforms, spectra Fast Fourier Transform (FFT), and total harmonic distortion as figures of merit. Theoretical considerations are verified by means of simulation and experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, a new topology for Z-source inverter based on switched Z-source network is proposed. The proposed switched Z-source inverter can provide high voltage gain in low duty cycles. The continuous input current is one of the other advantages of the proposed inverter. The performance of the proposed inverter is investigated in different operating modes and the voltage and current equations of all elements and equations of critical inductance are calculated. Furthermore, the power losses and efficiency analyses are presented. The comprehensive comparison between the proposed inverter and the other conventional Z-source inverters shows its excellent performance. Finally, to prove the correct operation of the proposed topology, the experimental and simulation results using PSCAD/EMTDC software are presented. [ABSTRACT FROM PUBLISHER]

In a switching-table-based direct torque control method (ST-DTC), the torque ripple reduces with increasing number of levels of the torque comparator. The number of levels is decided by the availability of the number of voltage vectors according to the topology of the inverter. This paper proposes the seven-level torque comparator to reduce the torque ripple in the DTC-controlled five-phase induction motor fed by the three-level five-phase inverter. In the five-phase induction motor, an elimination of x − y stator flux is inevitable otherwise the stator phase current will be distorted. In order to eliminate the x − y stator flux, the virtual voltage vectors are formed. Experimental results are presented to validate the proposed DTC method. [ABSTRACT FROM PUBLISHER]

This paper analyzes the performance of a grid-tied, wide power range, transformerless, modified three-phase current-source inverter (CSI), named CSI7. The CSI7 topology is here analyzed along with a suitable space vector modulation strategy able to attenuate the excitation of the output CL filter. The theoretical analysis and simple analytic expressions highlighted the performance and limitations of the topology when employed as a single-stage photovoltaic (PV) inverter, with a particular emphasis on injected grid current distortion and ground leakage current values. The inverter wide input range allows interfacing PV strings of different module count with a simple closed-loop control. The principle of operation and control is described; the viability of the CSI7 topology was assessed with simulations and extensive experiments on a full-size laboratory prototype. [ABSTRACT FROM PUBLISHER]

This paper presents a novel soft-switching galvanically isolated buck-boost dc–dc converter as a module-integrated converter for photovoltaic (PV) applications. It features three major operating modes: boost, normal, and buck mode. Their proper distribution over the input voltage range enables wide voltage regulation capabilities, i.e., close to those of nonisolated power optimizers. The proposed control algorithm requires only one buck-boost switching stage that performs voltage regulation by means of the switching stage reconfiguration with smooth transition between the modes. The design guidelines and the digital control system for PV applications are provided. The module-integrated converter was verified experimentally with a solar array simulator. The converter showed good maximum power point tracking performance and a peak efficiency of nearly 97%. [ABSTRACT FROM PUBLISHER]

In this paper, a new cascade switch-ladder multilevel inverter topology is presented which can generate a large number of output voltage levels. First, a fundamental switch-ladder multilevel inverter structure is described. Then, the structure of recommended cascade topology based on series connection of fundamental switch-ladder topologies is presented. To generate maximum number of levels with minimum number of switching elements, dc sources, and voltage on switches, the proposed cascade topology is optimized. Comparison results prove that the presented cascade topology requires fewer numbers of components. Also, the value of voltage rating on switches is less than other structures. Experimental results for two topologies are analyzed to verify the performance of the proposed topology. [ABSTRACT FROM PUBLISHER]