Search

This paper presents a model predictive control (MPC) scheme for quasi-Z-source (qZS) three-phase four-leg inverter. In order to cope with the drawbacks of traditional voltage source inverters (VSIs), a qZS three-phase four-leg inverter topology is proposed. This topology features a wide range of voltage gain which is suitable for applications in renewable energy-based power systems, where the output of the renewable energy sources varies widely with operating conditions such as wind speed, temperature, and solar irradiation. To improve the capability of the controller, an MPC scheme is used which implements a discrete-time model of the system. The controller handles each phase current independently, which adds flexibility to the system. Simulation and experimental studies verify the performances of the proposed control strategy under balanced and unbalanced load conditions as well as single-phase open-circuit fault condition. [ABSTRACT FROM PUBLISHER]

This paper addresses theoretical calculation of a single-phase multilevel pulsewidth modulation (PWM) inverter current total harmonic distortion (THD). Analytical approach introduced in late 1980s for a two-level inverter is generalized for an arbitrary level count for a single-phase inverter. Although the obtained closed-form piecewise analytical solutions assume (infinitely) large ratio of switching and fundamental frequencies and pure inductive load, they are practically very accurate for the ratios of (apparent) switching and fundamental frequencies larger than 25–30 and inductance-dominated loads. Along with strict mathematical solutions, simple accurate Bessel function approximation and hyperbolic average trend one are suggested. The formulas clearly reveal a single-phase PWM inverter current THD dependence on modulation index for an arbitrary voltage level count and are easily modified to cover grid-connected cases. [ABSTRACT FROM PUBLISHER]

The aim of this paper is to present a new structure for switched-capacitor multilevel inverters (SCMLIs) which can generate a great number of voltage levels with optimum number of components for both symmetric and asymmetric values of dc-voltage sources. The proposed topology consists of a new switched-capacitor dc/dc converter (SCC) that has boost ability and can charge capacitors as self-balancing by using the proposed binary asymmetrical algorithm and series–parallel conversion of power supply. The proposed SCC unit is used in new configuration as a submultilevel inverter (SMLI) and then, these proposed SMLIs are cascaded together and create a new cascaded multilevel inverter (MLI) topology that is able to increase the number of output voltage levels remarkably without using any full H-bridge cell and also can pass the reverse current for inductive loads. In this case, two half-bridge modules besides two additional switches are employed in each of SMLI units instead of using a full H-bridge cell that contribute to reduce the number of involved components in the current path, value of blocked voltage, the variety of isolated dc-voltage sources, and as a result, the overall cost by less number of switches in comparison with other presented topologies. The validity of the proposed SCMLI has been carried out by several simulation and experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, a new topology for half-bridge switched boost inverter (HB-SBI) is proposed. The proposed half-bridge inverter uses more active elements rather than capacitors and inductors in comparison with the conventional half-bridge Z-source inverter with two Z-networks, which results in reduction of weight, size, and cost. Moreover, the proposed inverter has the capability of eliminating inverter leg short-circuit issues and is able to further increase the output voltage level in comparison with its conventional types. Generating zero-level output voltage is also another advantage of this topology. Based on theoretical calculations, the steady-state and small-signal analysis of the proposed topology in different operating modes are performed and the ripple of inductors’ current and capacitors’ voltage are also calculated. A comprehensive comparison is also made between the proposed inverter and the conventional types. Finally, the experimental results are provided to reconfirm the performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

Modular multilevel converter (MMC) is a promising new topology for high-voltage applications. The MMC is made of several identical submodules. For proper operation, each submodule can be considered as a controlled voltage source where capacitor’s voltage should be maintained at a certain level. Besides, the minimization of the circulating current, which does not flow to the load, is crucial for achieving stable and efficient operation of the MMC. The interrelations among the load current, circulating current, and capacitor voltages complicate the MMC control. This paper aims to achieve stable and balanced voltage and current control with reduced circulating current in various operating conditions. The proposed control uses weighted model predictive control based on a normalized cost function to select the inverter switching patterns, which control the load current, while minimizing voltage fluctuation and circulating current. The weighting factors were selected based on minimizing the load-current total harmonic distortion (THD) and circulating current. The analysis is conducted on a low-power case study of single-phase four-cells MMC with possible extension to higher number of cells. The low-power three-level prototype is designed and built to validate this proposed method. Theoretical analysis, simulation, and experimental results are presented and compared. Parameter sensitivity analysis was also conducted. They all confirm the effectiveness of the proposed control method. [ABSTRACT FROM PUBLISHER]

Finite-state predictive torque control (FS-PTC) is computationally expensive, since it uses all voltage vectors (VVs) available from a power converter for prediction and actuation. The computational burden is rapidly increased with the number of VVs and objectives to be controlled. Moreover, designing a cost function with more than two control objectives is a complex task. This paper proposes a simplified algorithm based on a new direct torque control (DTC) switching table to reduce the number of VVs to be predicted and objectives to be controlled. The new switching table also assists to reduce average switching frequency and its variation range. As a result, the cost function is simplified by not requiring to include the frequency term. Experimental results show that the average execution time and the average switching frequency for the proposed algorithm are greatly reduced without affecting the torque and flux performances achieved in the conventional FS-PTC. [ABSTRACT FROM PUBLISHER]

The cost reduction of power-electronic devices, the increase in their reliability, efficiency, and power capability, and lower development times, together with more demanding application requirements, has driven the development of several new inverter topologies recently introduced in the industry, particularly medium-voltage converters. New more complex inverter topologies and new application fields come along with additional control challenges, such as voltage imbalances, power-quality issues, higher efficiency needs, and fault-tolerant operation, which necessarily requires the parallel development of modulation schemes. Therefore, recently, there have been significant advances in the field of modulation of dc/ac converters, which conceptually has been dominated during the last several decades almost exclusively by classic pulse-width modulation (PWM) methods. This paper aims to concentrate and discuss the latest developments on this exciting technology, to provide insight on where the state-of-the-art stands today, and analyze the trends and challenges driving its future. [ABSTRACT FROM PUBLISHER]

The flying capacitor multilevel inverter (FCMLI) is one of the well-known structures of multilevel inverters having attracted considerable attention because of its merits. In spite of its many advantages, it has some limitations such as high volume and complicated control method because of its bulky capacitors and their voltage balancing requirement. Moreover, the high number of power semiconductors required makes this structure susceptible to failure. To increase the ratio of the number of levels to the number of components, an uneven distribution of capacitor voltages has been suggested in previous reports; however, this approach complicates the control method. Up to now, almost all presented methods suffer from high computational load and/or structure-dependent algorithm. In this paper, a simple state-based and structure-independent method is proposed for capacitor voltage regulation. The proposed method is straightforward and can perform online computation of switching sequences in a computationally efficient manner without any need for stored information or look-up tables. The method is conveniently extendible to any number of cells and levels in an FCMLI structure with arbitrary dc link voltage distribution schemes. Simulation and experimental results show the effectiveness and simplicity of this method. [ABSTRACT FROM PUBLISHER]

In this paper, a common grounded Z-source dc–dc converter with high voltage gain is proposed for photovoltaic (PV) applications, which require a relatively high output–input voltage conversion ratio. Compared with the traditional Z-source dc–dc converter, the proposed converter, which employs a conventional Z-source network, can obtain higher voltage gain and provide the common ground for the input and output without any additional components, which results in low cost and small size. Moreover, the proposed converter features low voltage stresses of the switch and diodes. Therefore, the efficiency and reliability of the proposed converter can be improved. The operating principle, parameters design, and comparison with other converters are analyzed. Simulation and experimental results are given to verify the aforementioned characteristics and theoretical analysis of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, a new inverter topology is proposed for generating a multilevel dodecagonal voltage space vector structure for open-end winding induction motor (IM) using a single dc source. Dodecagonal voltage space vector structure eliminates fifth- and seventh-order harmonic voltages from phase voltage output and hence eliminates the fifth- and seventh-order harmonic currents through the motor leading to removal of the dominant sixth-order torque ripple generation in the motor over the entire modulation range. Multilevel space vector structure generates output voltage with better THD and low dv/dt. In the proposed topology, two three-level inverters drive an open-end winding IM, one inverter from each side. DC-link of primary inverter is from a dc source which delivers the entire active power, whereas the secondary inverter dc-link is maintained by a capacitor, which is self balanced during the inverter operation. The PWM scheme implemented ensures low switching frequency for primary inverter. Secondary inverter operates at a small dc-link voltage. Hence, switching losses are small for both primary and secondary inverters. Experimental results show the elimination of fifth- and seventh-order harmonic voltages over the entire modulation range, validating effectiveness of the proposed multilevel inverter scheme. [ABSTRACT FROM PUBLISHER]

A four-level open-end winding induction motor (OEWIM) drive is known to suffer from two perennial problems. One is the problem of zero-sequence currentin the motor phases, which is caused by the existence of zero-sequence voltage in them. The other is the overcharging of the dc-link capacitor of theinverter operated with lower dc-link voltage by its counterpart operated with a higher dc-link voltage. This paper investigates the applicability of aspecial variant of space vector pulse width modulation (SVPWM) scheme for a recently proposed power circuit configuration, in which arectifier–inverter combination is nested within the conventional two-level inverter configuration to achieve four-level inversion. This PWM schemeis named as the sample-averaged zero-sequence elimination (SAZE) SVPWM scheme, wherein the zero sequence voltage is suppressed in each sampling timeperiod in the average sense. Both of the aforementioned problems encountered in this drive are successfully overcome for this power circuit configurationby resorting to the proposed SVPWM strategy. [ABSTRACT FROM PUBLISHER]

This paper presents a boost-multilevel inverter design with integrated battery energy storage system for standalone application. The inverter consists of modular switched-battery cells and a full-bridge. It is multifunctional and has two modes of operation: 1) the charging mode, which charges the battery bank and 2) the inverter mode, which supplies ac power to the load. This inverter topology requires significantly less power switches compared to conventional topology such as cascaded H-bridge multilevel inverter, leading to reduced size/cost and improved reliability. To selectively eliminate low-order harmonics and control the desired fundamental component, nonlinear system equations are represented in fitness function through the manipulation of modulation index and the genetic algorithm (GA) is employed to find the optimum switching angles. A seven-level inverter prototype is implemented and experimental results are provided to verify the feasibility of the proposed inverter design. [ABSTRACT FROM AUTHOR]

This paper presents proportional integral direct torque control (PIDTC) and fuzzy-2 DTC (F2DTC) of the induction motor (IM) drive using space vector pulse width modulation (SVPWM) for three-level diode-clamped inverter (TDCI). The above control schemes have been implemented in the laboratory using 2 HP IM through a DSPACE DS-1104 controller. The control schemes are capable to balance the dc-link capacitor voltages of TDCI by selecting an optimum voltage vector without using an extra controller. However, the three-level PIDTC of an IM gives poor transient performance during starting, loading, and speed reversal with considerable current and voltage total harmonic distortion (THD). In addition, it takes more time to reach the steady state with large spikes on capacitor voltages during the load or speed variation. This is due to poor performance of the PI controllers (speed and torque). In F2DTC, the conventional PI controllers are replaced by Mamdani-type fuzzy-2 controllers using a centroid method with simple logical rules. The simulated and experimental performance show that F2DTC for the three-level inverter-fed IM drive provides a fast dynamic response, less current and voltage THDs, considerable less distortion in flux and torque, and fewer spikes on capacitor voltages as compared to PIDTC. [ABSTRACT FROM PUBLISHER]

In an electric drive vehicle (EDV), the available voltage on a dc-link is limited, and so the inverter output voltage and, consequently, the line motor maximum speed are limited. The fundamental voltage of the inverter output is increased approximately 27% using a square wave (SW) switching pattern instead of a sine wave switching pattern. However, this pattern can only be used at high speeds, and at lower speeds a pulsewidth modulation (PWM) pattern should be used. In order to achieve proper control, the switching pattern should be changed seamlessly. In the present paper, a new PWM scheme for single-mode seamless control of Vernier motors is proposed. In the proposed scheme, the reference voltage is modified to change the switching pattern continuously so that the voltage changes smoothly from a high-frequency pattern to an SW and voltage discontinuity does not occur. Experimental results reveal that the inverter-switching pattern changes smoothly from a sinusoidal PWM pattern to an SW pattern, and so seamless control from the constant-torque region to the constant-power region, and vice versa, is achieved. Since the proposed scheme is a single-mode control, it is much simpler than current technologies, which are based on multimode controllers. Also the proposed method has a lower total harmonic disturbance (THD) as well as a lower harmonic distortion factor (HDF) compared to some existing methods. [ABSTRACT FROM PUBLISHER]

Multilevel inverters are gaining more attention in ac drive application due to their many attractive features. In the case of conventional neutral-point-clamped (NPC) or flying capacitor multilevel inverter configurations, active switches are connected in series to produce multilevel output voltage waveform. Therefore, if any one switch fails, the entire configuration has to be shut down; this will reduce the reliability of the system. A dual three-level inverter configuration for induction motor drive is proposed in this paper to improve reliability of the system. This topology is developed by feeding four-pole induction motor stator winding with four conventional two-level inverter modules. A level-shifted carrier-based third harmonic injection pulsewidth-modulation technique is used to produce the gating signals for the proposed configuration. By providing proper phase shift between carrier waves, multilevel voltage waveform is produced across the total motor phase winding, and first center band harmonics are also canceled. Thereby, the torque ripple will be considerably reduced compared with conventional NPC five-level inverter-driven induction motor drive. Finite-element analysis (FEA) is used to estimate the torque ripple when induction motor is supplied by the proposed configuration and conventional five-level NPC inverter configuration to show the effectiveness of the proposed converter. The proposed configuration is simulated using MATLAB/Simulink and experimentally verified using a laboratory prototype with a 5-hp four-pole induction motor drive. [ABSTRACT FROM PUBLISHER]

Distributed maximum power point tracking (MPPT) photovoltaic (PV) systems have drawn increased attention since the inhomogeneous irradiance on PV modules can significantly deteriorate the effectiveness of solar energy harvest. To address the issue, this paper focuses on developing a highly efficient submodule integrated converter (subMIC), which is connected across each submodule of a PV panel. Gallium nitride (GaN) field-effect transistors are utilized in the synchronous buck converter topology to achieve high conversion efficiency and reduced size. A converter prototype, which is digitally controlled using a microcontroller for MPPT, is developed and tested, considering various irradiation conditions. The peak efficiency of the proposed GaN-based subMIC is measured to be higher than 99% at 400-kHz switching frequency, whereas the accuracy of MPPT is above 99% considering low-power conditions. [ABSTRACT FROM PUBLISHER]

This paper describes a single-phase full-bridge inverter that possesses limited current ripple at the dc link while providing a sinusoidal square power at the ac output. This is achieved through the addition of an extra pair of switches and complementary control for the full-bridge inverter. The extra switches operate to prevent the double-line frequency ripple current from flowing into the input of the inverter. In doing so, the pulsation component of the sinusoidal square output power is confined to flow between the output capacitors and the load. Thus, the dc link input only supplies the dc component of the output power. Simulation and experimental results validating the proposed solution are presented. [ABSTRACT FROM PUBLISHER]

In this paper, a novel grid-connected high step-up inverter is proposed. The topology is composed of two stages. The first stage is a single-switch high step-up dc–dc converter with bipolar outputs, and the second stage is a conventional half-bridge dc–ac grid-connected inverter. Negative grounding of the photovoltaic (PV) module has resulted in elimination of unwanted ground leakage currents in the PV system. Simple structure, employing few semiconductor switches, simple control, and high efficiency are the features of the proposed topology. Theoretical analysis and principal operation of the circuit are discussed. An experimental prototype is implemented to verify the performance of the proposed inverter. The experimental results confirm the aforementioned features and the theoretical analysis of the converter operation. [ABSTRACT FROM PUBLISHER]

Energy storage systems have been widely applied in power distribution sectors as well as in renewable energy sources to ensure uninterruptible power supply. This paper proposes a modified model predictive control (MMPC) method based on the Lyapunov function to improve the performance of a bidirectional ac–dc converter, which is used in an energy storage system for bidirectional power transfer between the three-phase ac voltage supply and energy storage devices. The proposed control technique utilizes the discrete behavior of the converter, considering the unavoidable quantization errors between the controller and the control actions selected from the finite control set of the bidirectional ac–dc converter. The proposed control method reduces the execution time delay by 18% compared with the conventional model predictive control. Moreover, the nonlinear system stability of the proposed MMPC technique is ensured by the direct Lyapunov method and a nonlinear experimental system model. Detailed experimental results with a 2.5-kW downscaled hardware prototype are provided to show the efficacy of the proposed control system. [ABSTRACT FROM PUBLISHER]

This paper presents a sliding-mode control (SMC) strategy for single-phase grid-connected \mboxLCL-filtered voltage source inverters (VSIs) with double-band hysteresis scheme. The proposed SMC is simpler than the existing SMC methods devised for grid-connected VSIs since its sliding-surface function requires the sensing of capacitor voltage and grid current only. In addition, a double-band hysteresis scheme which ensures the switching of a transistor in the VSI during a half cycle while it remains either on or off in the other half cycle of the fundamental period is used to mitigate the switching frequency. Furthermore, the analytical expressions for the instantaneous and average switching frequencies are derived. The theoretical considerations and analytical results are verified through computer simulations and experimental results obtained from a 3.3-kW system. Simulation and experimental results show that the proposed SMC strategy exhibits an excellent performance in achieving the required control objectives such as fast dynamic response, robustness, sinusoidal grid current with low total harmonic distortion, and simplicity in a practical implementation. [ABSTRACT FROM PUBLISHER]

This paper proposes a new topology for an enhanced-boost Z-source inverter (ZSI) with combined two Z-impedance networks. By two Z-impedance networks and low shoot-through duty cycle, the proposed inverter produces high output voltage gain. In traditional ZSIs for high boosting voltage, a low modulation index is required; hence, under these conditions, the output voltage will have low quality with high total harmonic distortion. Compared with the conventional high-boost ZSI topologies, the proposed inverter uses shorter shoot-through duration and a larger modulation index to improve the output waveform quality. Comparison between the proposed topology and previously proposed schemes, in terms of inductor numbers, voltage and current stresses on elements, sizes of inductors and capacitors, efficiency, and switching device product (SDP) factors of diodes, is made, and the results verify the priority of the proposed topology. The operating principle of the proposed topology is analyzed in detail. Both simulation and experimental results verify the high performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

In this paper, three overmodulation techniques for the three-to-five-phase indirect matrix converter (IMC) are proposed. The first technique utilizes only the adjacent large vectors in the sector in which the reference output voltage vector lies. The second technique improves on that by continuously adapting vector elimination in the d_2-q_2 vector space based on the output voltage requirements. The third technique utilizes the ripple in the dc link to further reduce the modulation index of the inverter stage during overmodulation. All three techniques increase the voltage transfer ratio of the three-to-five-phase IMC from 0.788 to 0.923, but with the addition of harmonics generated by a vector in the d_2-q_2 vector space of the inverter stage. Simulation and experimental results from a prototype three-to-five-phase IMC validate the three proposed overmodulation techniques. [ABSTRACT FROM AUTHOR]

This paper presents the establishment and operation control of a dc microgrid incorporating with electric vehicle (EV) as movable energy storage. The developed microgrid consists of a wind permanent-magnet synchronous generator ac source and a dc source, a battery/supercapacitor (SC)/flywheel hybrid energy storage system, and a grid-connected bidirectional single-phase three-wire (1P3W) load inverter. Various harvested ac and dc sources can be plugged into the microgrid via the developed interfaced power converters. In addition to good microgrid operation performance, the microgrid-to-grid and grid-to-microgrid operations can be successfully conducted with good power quality. As to the developed EV interior permanent-magnet synchronous motor drive, the SC auxiliary storage is equipped to assist the main battery source in intermittent energy conversion. Satisfactory acceleration/deceleration/reversible and regenerative braking operation characteristics are obtained via the developed power stages and control schemes. Moreover, the successful microgrid-to-vehicle and vehicle-to-microgrid interconnected operations of EV and microgrid are achieved. In addition, the vehicle-to-grid/grid-to-vehicle operations can be also performed via the developed 1P3W inverter. [ABSTRACT FROM AUTHOR]

Hysteresis model predictive control (HMPC) is a variant of finite-control-set model predictive control, which is mainly developed for high-power applications. In this paper, the HMPC scheme is proposed to control a high-power grid-connected two-level voltage source inverter with an inductive-capacitive-inductive (LCL) filter. To ensure the stable operation of the control system, the resonance characteristics of the system with an LCL filter based on HMPC are analyzed, and an active damping scheme is then given. On the other hand, the impacts of the modeling error on system stability and average switching frequency are analyzed in detail. Then, a new switching frequency-adaptive control scheme that uses the average switching frequency to adjust the parameter value of the predictive model online is presented. The new control scheme can keep the average switching frequency within an acceptable operational margin, while improving the stability of the control system. For demonstration, the proposed control scheme has been implemented on a small-scale grid-connected inverter system, and the results show that the theoretical analysis is correct and that the proposed control scheme is effective. [ABSTRACT FROM AUTHOR]

In this paper, a modified zero-voltage-switching pulsewidth-modulation inverter with a digital-signal-processor-based proportional–integral–derivative (PID)-like fuzzy controller (PIDFC) is implemented. The switches of the inverter can achieve a soft-switching feature that can largely reduce switching losses and improve the converting efficiency. In order for the online control of the proposed dc–ac inverter to be feasible, a fuzzy control is designed to be a PID-like fuzzy mechanism with the complexity significantly reduced. From the results, it is shown that the PIDFC can not only stabilize the output at 110 V rms but can also improve the performance when the system load has been changed from 600 to 100 $\Omega$. Comparing with a traditional PID controller, the responding speed can be improved by 75% in the simulation, and the speed can still be improved by 35% in the practice experiment. [ABSTRACT FROM AUTHOR]

Carrier-based pulsewidth-modulation (CBPWM) techniques are popular due to their simplicity, and have been widely researched for various three-phase inverter configurations. In this paper, two CBPWM techniques are proposed to reduce the common-mode (CM) voltage generated by the five-phase inverter. The five-phase inverters have more flexibility in reducing the CM voltage than their three-phase counterparts because they have more phase legs, hence finer control over the star-point voltage of the load. Two methods are proposed for the conventional two-level five-phase inverter to reduce the CM voltage; one utilizing adjacent modulating waveforms and the other utilizing nonadjacent modulating waveforms. The coupled inductor inverter (CII) uses coupled inductors to generate multilevel outputs. As the volt-second balance must be maintained across each coupled inductor, direct application of the proposed methods on the CII inverter will result in overcurrents in the coupled inductors. Hence, the proposed methods are further improved to ensure the volt-second integral over each switching period is zero. Moreover, the two proposed methods are designed to reduce switching events and prevent unexpected states occurring during the switching transitions. The performance and the switching strategy of both methods are verified by both simulations and experiments on a prototype of five-phase CII. [ABSTRACT FROM AUTHOR]

This paper proposes an indirect matrix converter (IMC) topology to supply a five-phase load directly from three-phase ac power sources without bulky electrolytic capacitors and explains its operating principle. Using the emerging topology, which combines the five-leg inverter into the rectifier stage of the conventional IMC, the three-to-five-phase IMC topology reduces the number of power switches and results in a simpler commutation compared with the conventional three-to-five-phase direct matrix converter. In addition, a simple approach to realize the carrier-based pulsewidth modulation (CBPWM) method for a three-to-five-phase IMC is presented, and the proposed CBPWM method is analyzed based on the space-vector approach. As a result, the IMC with the proposed CBPWM method can be more easily implemented compared with IMCs with the space-vector PWM method. A three-to-five-phase IMC control platform is realized by coordinating a TMS320F28335 DSP (Texas Instruments) with an EPM7128SLC84-15 field-programmable gate array (Altera). The simulation and experimental results are provided to verify the effectiveness of the CBPWM strategy. [ABSTRACT FROM AUTHOR]

Multiphase machines are well known for their fault-tolerant capability. Star-connected multiphase machines have fault tolerance in an open circuit. For an inverter switch short-circuit fault, it is possible to keep a smooth torque of a permanent magnet synchronous machine if the currents of the faulty phases are determined and their values are acceptable. This paper investigates fault-tolerant operations of an open-end five-phase drive, i.e., a multiphase machine fed with a dual-inverter supply. Inverter switch short-circuit fault is considered and handled with a simple solution. Original theoretical developments are presented. Simulation and experimental results validate the proposed strategy. [ABSTRACT FROM AUTHOR]

This paper presents fuzzy-2 direct torque control (F2DTC) and proportional–integral direct torque control (PIDTC) of an induction motor drive (IMD) using bus-clamped space vector modulation (BCSVM). The PIDTC gives considerable flux and torque ripples with the poor dynamic performance of the IMD. To improve the dynamic performance of IMD, F2DTC is proposed. In F2DTC, proportional–integral controllers are replaced by fuzzy-2 controllers (F2Cs), where the BCSVM duty ratios are independent of the sampling period. The firing strength of the inverter with F2DTC is improved than the PIDTC. In addition, the F2C effectively deals with the huge ambiguous data using Mamdani and Centroid methods with simple IF and THEN rules. A prototype controller is developed in the laboratory, and the control signals for both PIDTC and F2DTC are generated by the DSPACE DS-1104 controller. The F2DTC provides fewer ripples in flux and torque and less current total harmonic distortion than the PIDTC. Moreover, F2DTC has fast dynamic performance of the IMD as compared with PIDTC. [ABSTRACT FROM PUBLISHER]

In this paper, a fault-tolerant single-phase five-level inverter configuration is proposed for photovoltaic (PV) generation systems. Conventional two-level inverters are popularly used in PV applications, but these inverters provide the output voltage with considerable harmonic content. One of the efficient ways to improve the power quality of PV generation systems is to replace a two-level inverter with a multilevel inverter. Conventional multilevel inverters reduce total harmonic distortion and filter requirements effectively, but it has limitations in terms of reliability due to increased device count and capacitor voltage balancing issues. Therefore, a fault-tolerant single-phase five-level inverter is presented, which is constructed by using a half-bridge two-level inverter, a three-level diode clamp inverter, and a bidirectional switch. The proposed inverter topology can tolerate the system faults due to failure of the source and/or switching devices with least modification in the switching combinations. It has less number of switching devices compared to conventional five-level inverters. The topology also has the energy-balancing capability between sources which helps in reducing uneven charge of batteries in case of partial shading or hotspots on one side of the PV panels. The proposed system under normal and faulty condition is simulated in MATLAB/Simulink environment, and results are verified with a laboratory prototype. [ABSTRACT FROM PUBLISHER]

This paper focuses on the galvanically isolated quasi-Z-source dc–dc converter with a novel zero voltage and zero current switching technique. The unique feature of the impedance network lies in combining the buck–boost operation capability with the short- and open-circuit immunity of transistors; at the same time, it can perform zero voltage and zero current switching on the primary side. The boundary conduction mode of the current in the second inductor of the quasi-Z-source network was used along with snubber capacitors in the two out of four transistors and a special control algorithm to achieve full zero-switching operation of the inverter. Simulation and experimental results prove the discussed ideas. Possible modifications of the algorithm and future applications are also described. [ABSTRACT FROM PUBLISHER]

In this paper, an advanced configuration for a symmetric multilevel voltage source inverter is proposed. The authority of the proposed inverter versus the conventional cascaded H-bridge inverter and those most recently introduced is verified with provided comparisons. The proposed inverter is able to generate the desired voltage levels using a lower number of circuit devices, including power semiconductor switches and related gate driver circuits of switches. As a result, the total cost is considerably reduced, and the control scheme gets simpler. Moreover, the reduced amount of on-state switches in the suggested configuration decreases voltage drops. Furthermore, power losses are diminished. The given simulation results confirm the feasibility of the proposed configuration. To approve the practicability of the proposed inverter, a prototype of the proposed topology has been implemented. Finally, simulation and experimental results are compared, and the provided comparison shows that the obtained results are in good agreement. [ABSTRACT FROM PUBLISHER]

In this paper, a multilevel dodecagonal voltage space vector structure with nineteen concentric dodecagons is proposed for the first time. This space vector structure is achieved by cascading two sets of asymmetric three-level inverters with isolated H-bridges on either side of an open-end winding induction motor. The dodecagonal structure is made possible by proper selection of dc link voltages and switching states of the inverters. The proposed scheme retains all the advantages of multilevel topologies as well as the advantages of dodecagonal voltage space vector structure. In addition to that, a generic and simple method for calculation of pulsewidth modulation timings using only sampled reference values ( $v_\alpha$ and $v_\beta$) is proposed. This enables the scheme to be used for any closed-loop application such as vector control. In addition, a new method of switching technique is proposed, which ensures minimum switching while eliminating the fifth- and seventh-order harmonics and suppressing the eleventh and thirteenth harmonics, eliminating the need for bulky filters. The motor phase voltage is a 24-stepped waveform for the entire modulation range thereby reducing the number of switchings of the individual inverter modules. Experimental results for steady-state operation, transient operation, including start-up have been presented and the results of fast Fourier transform analysis is also presented for validating the proposed concept. [ABSTRACT FROM PUBLISHER]

In this paper, a new cascaded multilevel inverter is proposed. For the proposed inverter, two different algorithms to determine the magnitude of the dc voltage sources are proposed. Then, in order to generate maximum numbers of output voltage levels by using a constant number of power switches and/or dc voltage sources, several optimum structures of the proposed inverter are obtained. In comparison with the conventional cascaded multilevel inverters, the proposed inverter is able to generate a high number of output voltage levels by using a lower number of power electronic devices such as power switches, driver circuits, power diodes, and dc voltage sources. In addition, the low amount of blocked voltage by switches is another advantage of the proposed inverter. The accuracy performance of the proposed inverter in generating the positive and negative voltage levels is verified through the experimental results on a 61-level inverter. [ABSTRACT FROM PUBLISHER]

This paper presents a 100-kW 100-kHz insulated-gate bipolar transistor (IGBT) series resonant inverter for induction heating applications that uses an improved power control scheme based on the standard pulse density modulation (PDM). This standard power control is a good solution for the design of high-frequency inverters because the output power factor is near to unity in a wide range of output power, resulting in great reduction of switching losses and electromagnetic noise. However, the output current can be in discontinuous mode, particularly for resonant loads of low quality factor or for low output power or low-load operation. This output current fluctuation produces a high output current ripple that can lead to an increase in power losses and loss of accuracy of the response of the frequency tracking control. The proposed control strategy, which is called enhanced PDM (EPDM), provides twice less output current ripple, thus resulting in an improved inverter behavior in terms of frequency tracking accuracy and energy efficiency. Experimental tests have been made, in order to compare the EPDM strategy with standard power control schemes. [ABSTRACT FROM PUBLISHER]

In this paper, the two-input buck converter is proposed as the dc/dc stage for photovoltaic (PV) cascaded converters. This converter is attractive for this application because it is cost effective and reliable and can achieve dual maximum power point tracking (MPPT) with only one power transistor. However, due to the simplified and integrated structure, the nonlinear characteristics of the converter and the two PV arrays complicate the control. By means of a small-signal modeling, the control theme of the two PV voltages is formulated, and the effect of the nonlinearities is presented. It is shown that, while fast voltage dynamics are achieved for the first input, the second-input voltage response depends on the second-stage converter control. Simulation and experimental results are reported to validate the theoretical analysis, showing the dual MPPT capability. [ABSTRACT FROM PUBLISHER]

A division–summation (D-\mathbf\Sigma) digital control for three-phase inverters to achieve active and reactive power injection has been presented. It can overcome the limitation of abc to dq frame transformation. However, the D-\mathbf\Sigma control requires four sets of control laws to cover four quadrant operations, namely, grid connection (power factor (PF) 1 $\sim\pm$0.866), rectification with PF correction, PF leading (0 \sim$ 0.866), and PF lagging (0 \sim$ −0.866). Moreover, the switching sequences for the four modes are also different from each other, increasing complexity of firmware programming. In this paper, improvement of the control law derivation and region selection for the (D), which can obtain the control law directly. Measured results from a 10-kVA 3 $\phi$ bidirectional inverter have been presented to confirm the improvement. [ABSTRACT FROM PUBLISHER]

Back-to-back converters have been typically used to interconnect microgrids. For a back-to-back current-source converter, the dc-link current ripple is one of the important parameters. A large ripple will cause electromagnetic interference, undesirable high-frequency losses, and system instability. Conventionally, with a given switching frequency and rated voltage, the current ripple can be reduced by increasing the dc-link inductor, but it leads to bulky size, high cost, and slow dynamic response. To solve this problem, this paper reveals that the current ripple can be significantly reduced by adjusting the gate patterns of space vector modulation between the rectifier and the inverter in a back-to-back converter. The experimental results verify the effectiveness of the proposed method. [ABSTRACT FROM PUBLISHER]

Local dc distribution systems or dc nanogrids for residential and commercial buildings are growing popular due to the increased focus on energy savings. Using low-voltage dc for the nanogrid provides various advantages such as easier integration with renewable sources and battery banks, increased savings, etc. Future systems would use renewable sources and storage devices to become self-sufficient in generation with bare minimum consumption from the grid. The objective of this paper is to develop an energy management system (EMS) to provide uninterrupted power supply to the dc loads and achieve self-sufficiency by minimizing grid power consumption. This is achieved by developing a control scheme for a cascaded two-stage bidirectional converter interface between the nanogrid and the ac distribution network. In addition, an empirical relation for power flow through the converter is obtained, and an optimal capacitor link voltage range is derived to achieve power transfer between rated limits. The efficacy of the proposed control algorithm for the EMS is analyzed and proved to be well suited for the self-sustained dc nanogrid. A 5-kVA prototype of the converter is designed and developed in hardware, and the system operation is verified with experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes an improved performance interactive distribution static compensator (DSTATCOM) to address the limitations of conventional current control mode (CCM) and voltage control mode (VCM) operations. The proposed interactive scheme provides smooth transfer of modes of operation while remaining connected in the distribution system. In normal operation, the DSTATCOM operates in CCM to make source currents balanced, sinusoidal, and at a unity power factor. During voltage disturbances, the CCM operation cannot improve load voltage. In that case, DSTATCOM operation is changed to VCM, which maintains a constant voltage across the sensitive loads. Hence, this interactive DSTATCOM ensures continuous, flexible, and robust operation of the load. Moreover, the filter current requirements are reduced in the proposed scheme, which reduces the losses in the filter and feeder, improves inverter efficiency, and requires a reduced-rating inverter for sag mitigation. The principle of operation and control for both operating modes is analyzed. The detailed process of the flexible transfer between the two modes is derived. Deadbeat predictive control algorithms for CCM as well as VCM operation are developed for fast operation during mode transfers. The performance of the proposed scheme is validated by both simulation and experimental results. [ABSTRACT FROM PUBLISHER]

Common-mode voltage (CMV) is one of the most important issues for the power electronics inverters. An interesting space vector modulation of the three-leg current-source inverter has been reported for the CMV reduction recently. However, it has the disadvantages of the bipolar current pulses and modulation index range limitation. In order to solve these problems, a four-leg current-source inverter with a new space vector modulation is proposed in this paper. With the proposed method, the system CMV can be significantly reduced without bipolar current pulses and modulation index range limitation. Finally, the experimental tests are carried out on a four-leg current-source inverter, and the experimental results verify the effectiveness of the proposed method. [ABSTRACT FROM PUBLISHER]

According to the requirement of fuel cell generation system, this paper presents a new single-stage and boost-voltage grid-connected inverter, as well as the signal modulation diagram in a line cycle. In the proposed inverter, one of the bridge legs is shared with a boost converter. The boost inductor current is designed in discontinuous conduction mode, which can effectively decrease low-frequency current ripple (LFCR) in the output current of the fuel cell. The switching modes of the proposed inverter are analyzed in positive and negative half line cycles, respectively. The LFCR in the output current of the fuel cell is analyzed, from which the design principle of the boost voltage inductor is obtained. The per-unit current values of the shared switches and the loss of the whole system are derived and compared with those of the conventional inverter. Experimental verifications are presented to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

This paper proposes a control strategy of finite-control-set model predictive torque control (FCS-MPTC) with a deadbeat (DB) solution for permanent-magnet synchronous motor drives. By using a DB solution, the process of selection of the best switching vector is optimized. The predicted DB voltage sector consisting of the desired voltage vector (VV) avoids the complete enumeration for testing all feasible VVs, which relieves the big calculation effort of the traditional FCS-MPTC method. The proposed system is experimentally carried out both in the steady state and in the transient state. [ABSTRACT FROM PUBLISHER]

This paper proposes a technique to suppress low-order harmonics for an open-end winding induction motor drive for a full modulation range. One side of the machine is connected to a main inverter with a dc power supply, whereas the other inverter is connected to a capacitor from the other side. Harmonic suppression (with complete elimination of fifth- and seventh-order harmonics) is achieved by realizing dodecagonal space vectors using a combined pulsewidth modulation (PWM) control for the two inverters. The floating capacitor voltage is inherently controlled during the PWM operation. The proposed PWM technique is shown to be valid for the entire modulation range, including overmodulation and six-step mode of operation of the main inverter. Experimental results have been presented to validate the proposed technique. [ABSTRACT FROM PUBLISHER]

In this paper, selective harmonic mitigation (SHM) and selective harmonic elimination (SHE) modulation techniques have been combined to produce appropriate pulses for a four-leg three-level neutral point clamped (NPC) inverter. In the proposed hybrid method, the SHM technique is applied to phase legs in order to mitigate non-triplen harmonics (fifth, seventh, $\ldots$) , and the fourth leg is controlled by the SHE principle to eliminate important low-order triplen harmonics (third, ninth, $\ldots$) completely. In this context, it is demonstrated that using SHM instead of an SHE modulator for phase legs leads to a reduced vast range of harmonic orders in the NPC output voltage, significantly. Moreover, it is proved that the presented hybrid switching technique has the ability of dc-bus capacitor voltage balancing, inherently. Furthermore, analyses are performed to calculate the dc-bus capacitances accurately to show 5% voltage ripple acceptably. Simulation and experimental results validate a good dynamic performance of the proposed hybrid modulation technique in firing the NPC inverter switches to generate low-harmonic voltage waveforms supplying balanced and unbalanced loads while balancing the dc capacitor voltages in a four-wire network with small dc-link capacitors. [ABSTRACT FROM PUBLISHER]

In photovoltaic (PV) grid-connected generation system, the key focus is how to expand the generation range of the PV array and enhance the total efficiency of the system. This paper originally derived expressions of the total loss and grid current total harmonics distortions of cascaded inverter and H-bridge inverter under the conditions of variable output voltage and power of the PV array. It is proved that, compared with the H-bridge inverter, the operation range of the cascaded inverter is wider, whereas the total loss is larger. Furthermore, a novel online variable topology-type grid-connected inverter is proposed. A bidirectional power switch is introduced into the conventional cascaded inverter to connect the negative terminals of the PV arrays. When the output voltages of the PV arrays are lower, the proposed inverter works under cascaded inverter mode to obtain wider generation range. When the output voltages of the PV arrays are higher, the proposed inverter is transformed into equivalent H-bridge inverter mode to reduce the total loss. Thus, wider generation range and higher efficiency are both implemented. Specific demonstration of the proposed inverter based on five-level cascaded inverter is presented. The detailed experimental results verify the accuracy and feasibility of the theoretical analysis and the proposed inverter topology. [ABSTRACT FROM PUBLISHER]

This paper proposes novel multilevel ac/dc/ac converters with reduced number of semiconductor devices to achieve light weight, efficiency, and better input current quality. The proposed three-phase front-end bidirectional five-level (5L) rectifier and rear-end 5L inverter are constructed based on multiple-pole multilevel diode-clamped (M2DCC) approach, which consist a total number of 24 diode components clamped. Based on the M2DCC concept, the number of switching devices can be further reduced to construct a new unidirectional front-end rectifier (M2SCR). Comparative studies are conducted to analyze the performances of the two proposed front-end rectifiers with supportive mathematical derivations. Experimental prototypes have proven the feasibility of the proposed ac/dc/ac configurations. Results obtained show that low current harmonic distortions of 5% and high power factor of 0.99 are achieved with small input inductors despite low-switching-frequency operation at 1 kHz. [ABSTRACT FROM PUBLISHER]

This paper proposes an improved half-bridge inverter with wide-input-voltage capability for ozone-driven circuits. The study is motivated because the limited regulation of input voltage often affects the operation flexibility of ozone-driven circuits. Therefore, a modification of a half-bridge inverter along with a multiwinding coil design is proposed in this study, anticipating an increase in the range of input voltage and benefiting the industry applications. To confirm the practicality of this method, a hardware circuit was made with extensive validation. Experimental outcomes support the feasibility of this proposed method for ozone generators, exhibiting a potential of the method extending to other voltage-source applications. [ABSTRACT FROM PUBLISHER]

Single-phase voltage source transformerless inverters have been developed for many years and have been successful commercial applications in the distributed photovoltaic (PV) grid-connected systems. Moreover, many advanced industrial topologies and recent innovations have been published in the last few years. The objective of this paper is to classify and review these recent contributions to establish the present state of the art and trends of the transformerless inverters. This can provide a comprehensive and insightful overview of this technology. First, the generation mechanism of leakage current is investigated to divide the transformerless inverters into asymmetrical inductor-based and symmetrical inductor-based groups. Then, the concepts of dc-based and ac-based decoupling networks are proposed to not only cover the published symmetrical inductor-based topologies but also offer an innovative strategy to derive advanced inverters. Furthermore, the transformation principle between the dc-based and ac-based topologies is explored to make a clear picture on the general law and framework for the recent advances and future trend in this area. Finally, a family of clamped highly efficient and reliable inverter concept transformerless inverters is derived and tested to offer some excellent candidates for next-generation high-efficiency and cost-effective PV grid-tie inverters. [ABSTRACT FROM PUBLISHER]

In this paper, a simplified pulsewidth modulation with switching constraint control scheme is proposed to eliminate the circulating currents for bidirectional paralleled ac/dc converters in grid-tied system. The proposed control scheme can reduce the circulating currents and does not need additional current sensors and communication device among paralleled converters compared with conventional methods. Therefore, the paralleled system cost can be reduced. In addition, the current shaping and sharing between the paralleled converters can be well accomplished so that the overall performance of the paralleled converter system can be raised. Furthermore, the dc, ac, and self-generated circulating currents are clearly analyzed by graphics, and the synchronous circulating currents are first explored. Finally, a prototype system is constructed, and the proposed control scheme is implemented using a Spartan-3E XC3S250E FPGA. Both simulation and experimental results verify the validity of the proposed theory and control scheme. [ABSTRACT FROM PUBLISHER]