Search

Due to the higher attenuation of switching frequency current harmonics, the $LCL$ filter has been widely used in grid-connected inverters. To deal with the resonance of the $LCL$ filter, the capacitor current is usually fed back to damp the resonance actively. However, the computation and pulsewidth modulation (PWM) delays in the digital control system have a significant influence on the active damping method, resulting in poor system robustness. Meanwhile, these delays also reduce the control bandwidth greatly and thus impose a severe limitation on the low-frequency gains. In this paper, a real-time computation method with dual sampling mode is proposed to remove the computation delay from the inner active damping loop and the outer grid-current control loop simultaneously; thus, the system robustness and the control performance can be greatly improved. Moreover, the time duration between the sampling instant and the switching transition of the inverter bridge is extended by the proposed method, which effectively prevents the switching noise distorting the sampled signals. Therefore, the noise immunity of the inverter is also improved greatly. Experimental results from a 6-kW $LCL$-type single-phase grid-connected inverter confirm the theoretical expectations and the effectiveness of the proposed method. [ABSTRACT FROM PUBLISHER]

This paper presents a multifunctional onboard battery charger for plug-in electric vehicles (PEVs). The proposed battery charger consists of three H-bridge modules including a selective switch, a high-frequency transformer, and inductors. The first duty of the proposed charger is to charge the propulsion battery when PEV connects to the ac grid [onboard charger (OBC)]. In this case, the proposed charger plays a role in ac-to-dc converting with power factor correction. Occasionally, the propulsion battery can supply surplus energy to the grid [vehicle to grid (V2G)]. In this second task, the proposed charger acts as an inverter. The third role is to charge the auxiliary battery via the propulsion battery when PEV is in a driving state [low-voltage dc-to-dc converter (LDC)]. In this case, the proposed charger acts as a step-down converter. In conventional PEVs, the aforementioned functions are done by an OBC and an LDC separately. The proposed charger can implement the three tasks by sharing switches and inductors in an all-in-one system. Thus, the proposed approach can realize a small and light design of the EV battery charger, resulting in the improvement of fuel efficiency. After theoretical analysis, we carry out simulations and experiments using a prototype to verify the validity of the proposed approach. [ABSTRACT FROM PUBLISHER]

This paper presents an effective circuit configuration of a multilevel inverter that can increase the number of output voltage levels with a reduced number of circuit components. The proposed seven-level pulsewidth-modulation inverter consists of a single dc voltage source with a series of capacitors, diodes, active switches for synthesizing output voltage levels, and an H-bridge cell. After theoretical analysis, we carry out computer-aided simulations and experiments to verify the validity of the proposed approach. Here, we also introduce a modified switching strategy to solve the capacitor voltage unbalancing that occurs in series-connected capacitors. [ABSTRACT FROM PUBLISHER]

This paper presents a novel microinverter for a single-phase grid-connected photovoltaic (PV) system. The proposed microinverter consists of a step-up dc–dc converter using an active-clamp circuit with a series-resonant voltage doubler and a high-efficiency inverter with single-switch-modulation step-down converters. The active-clamp circuit provides zero-voltage switching (ZVS) turn-on, recycles the energy stored in the leakage inductance of the transformer, and limits switch voltage stress. Moreover, to remove the reverse-recovery problem of the rectifier diodes, a series-resonant voltage doubler is used. Thus, this whole process provides high efficiency. To improve efficiency and reliability in the proposed inverter, only a single switch is modulated at the switching frequency without a shoot-through problem. A modified controller is also adopted to achieve fast output control. Thus, the proposed PV microinverter has the structure to minimize power losses. The experimental results show a maximum efficiency of 96.2% for a 400-W microinverter. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel multiple-input bidirectional dc–dc power converter to interface more than two dc sources of different voltage levels. This finds applications in hybrid electric/fuel cell vehicles (FCVs), where different dc sources of unequal voltage levels need to be connected with bidirectional power flow capability. The converter can be used to operate in both the buck and boost modes with bidirectional power control. It is also possible to independently control power flow between any two sources when more than two sources are actively transferring power in either directions. The operation, analysis, and design of the converter are presented with different modes of power transfer. The proposed converter is demonstrated for FCV application using real-time hardware-in-the-loop system. Experimental results for a 5-kW system are presented, validating the theoretical analysis. [ABSTRACT FROM PUBLISHER]

This paper presents an experimental implementation of a predictive control strategy for a system made up of two induction machines fed by a six-leg indirect matrix converter. The objective is to evaluate the practical feasibility of this method, considering the large computational cost, and to incorporate available market technologies. This strategy achieves tracking of torque, speed, and flux references on both machines, minimizing the instantaneous input reactive power present in the system. A theoretical explanation of the main concepts that are used in the predictive control strategy is presented, along with comments on the experimental implementation, experimental setup, and results obtained under both balanced and unbalanced grid conditions. [ABSTRACT FROM PUBLISHER]

The phasor-PWM-based current source inverter (CSI) is a boost inverter. The difference between conventional CSIs and the boost inverter is that the boost ratio (VLLrms/Vdc ) in the boost inverter can easily be above 3.0, whereas this ratio is around 1 in conventional CSIs. In order to realize the potential capabilities of the boost inverter and to assist its penetration into renewable energy systems, the boost inverter dynamic behaviors are studied in this paper. First, the large- and small-signal models as well as the dq-equivalent circuits of the boost inverter are presented. Then, the developed models are verified using circuit simulations and experiments on a laboratory-scale 2-kW 208/240- V_{\rm LLrms} V_{\rm dc}=65\ \hbox{V} $ boost inverter made of reverse-blocking IGBTs. Finally, the developed small-signal model is used to study the stability of the boost inverter through root locus of small signal poles (eigenvalues) as control inputs, and load parameters vary within the boost inverter's operating limits. [ABSTRACT FROM PUBLISHER]

Three-phase multilevel (ML) inverters are used in many medium- and high-power applications such as motor drives and grid-connected systems. Despite the fact that numerous pulsewidth modulation (PWM) techniques for ML inverters have been developed, the impact of these modulation schemes on the peak-to-peak output current ripple amplitude has not been addressed yet. In this paper, analysis and comparison of current ripple for two-level (2L) and three-level (3L) voltage source inverters are given. Reference is made to optimal and popular modulation, so-called centered PWM, easily obtained by both carrier-based modulation (phase disposition, with proper common-mode voltage injection) and space vector modulation (nearest three vectors). It is shown that the peak-to-peak current ripple amplitude in 3L inverters can be determined on the basis of the ripple in 2L inverters, obtaining the same results as by directly analyzing the output voltage waveforms of the 3L inverters. This procedure can be readily extended to higher level numbers. The proposed analytical developments are verified by both numerical simulations and experimental tests. [ABSTRACT FROM PUBLISHER]

Power converters using deterministic switching frequency schemes have switching noise concentrated at harmonic frequencies, resulting in enhanced electromagnetic emission. To suppress the harmonic spikes in three-phase multilevel voltage source converters, a digital control scheme based on dithered sigma–delta modulation (SDM) is proposed in this paper. Introducing a dithered sequence in an SDM varies the switching frequency randomly, resulting in the suppression of the spurious harmonic spikes in the output spectrum even with a regular control input. Although the switching frequency varies randomly, the minimum pulsewidth of the proposed scheme is the sampling time period, avoiding the minimum pulsewidth problem. Instead of a conventional scalar quantizer, the quantizer in the proposed dithered sigma–delta converter uses the principle of space vector quantization. The proposed scheme is experimentally verified on a constant $v/f$ open-loop induction motor drive for a three-level inverter realized by cascading two two-level inverters. The performance of the proposed scheme is compared with different pulsewidth modulation schemes in the entire modulation index, including the overmodulation region. [ABSTRACT FROM PUBLISHER]

Grid-connected power converters play a key role in several applications such as the integration of renewable energy sources and motor drives. For this reason, the development of high performance control strategies for this particular class of power converters has increasingly attracted the interest of both academic and industry researchers. This paper presents the predictive optimal switching sequence (OSS) direct power control (DPC) (OSS-DPC) algorithm for grid-connected converters. The OSS-DPC method belongs to the predictive-DPC family and provides the desired power references by calculating globally OSSs. To address computational and implementation issues, an efficient control algorithm, named reduced OSS-DPC, is introduced. The implementation of the proposed control strategy in a standard DSP is evaluated on a two-level power converter prototype working as a STATCOM. Experimental results show the algorithm's potential to provide high performance during both transient and steady states. [ABSTRACT FROM PUBLISHER]

Power converters are complex devices subject to failures that can lead to undesired stops. For this reason, many fault-tolerant topologies and strategies have been deeply studied, mainly focusing on improving the electromechanical behavior of the reconfigured drive after the fault. However, it is also very important to evaluate the possible increase of power losses. In this paper, a power loss analysis is performed on a current-controlled three-phase inverter supplying a permanent-magnet synchronous motor (just chosen as an example), for all the operating modes, starting from the fault occurrence until the faulty operation mode is established. This is particularly important because the effectiveness of a fault-tolerant control strategy depends on the possibility to maintain a continuous operation. The latter is ensured only if there is no such increment of the losses that the survival of the component is at risk. The simulations are validated by means of experimental tests, and the results are discussed. The method can be easily applied to other topologies and reconfiguration strategies. [ABSTRACT FROM PUBLISHER]

Today's variable-speed drives are usually operated close to their maximum tolerable conditions. The fast switching of modern power electronic devices leads to high stress of the winding insulation. As a result, an insulation breakdown may lead to sudden breakdown and high economic loss. To avoid unpredictable downtimes and enable repair on demand, monitoring of the insulation health state is getting more and more important. This paper proposes a method to monitor changes in the insulation health state by evaluating the machine high-frequency properties. The deterioration of the insulation condition is usually linked with a change of insulation capacity and thus also influences high-frequency properties. Initiating a voltage step excitation of the machine by the switching of the inverter, the high-frequency properties can be identified by measuring the resulting current response. This response is usually seen as current signal ringing and contains the machine high-frequency information. By applying signal processing tools, changes in the high-frequency information are extracted, and an insulation state indicator is derived. The applicability of the method is verified by measurements on two test machines (5.5 kW and 1.4 MW) having different power ratings as well as different insulation systems. [ABSTRACT FROM PUBLISHER]

This paper presents a circuit structure with a novel inverter that is applicable to arc welding machines. The output rectifier configuration adopts the current doubler rectifier with two coupled inductors. The proposed inverter topology can keep the energy stored in the coupled inductor until the next commutation interval. Moreover, the conduction loss will be lower, which improve the conversion efficiency of the arc welding machine. The operation principle, control circuit, and inverter design example are also described in detail. Experimental results demonstrate the feasibility and efficiency of the proposed inverter topology. [ABSTRACT FROM PUBLISHER]

A switched boost inverter (SBI) can replace a $Z$-source inverter (ZSI) in low-power applications because it has one less $LC$ pair than the ZSI. This paper presents a class of quasi-SBIs (qSBIs) that offers several advantages when compared with a conventional SBI, including reducing the voltage stress on the capacitor, increasing the boost voltage factor, and improving input current profiles. Operating principles, steady-state analysis, and comparisons with conventional inverters are presented. A prototype based on a TMS320F28335 digital signal processor is built to verify the operating principle of the proposed qSBIs. [ABSTRACT FROM PUBLISHER]

Many recent multilevel inverter papers end up with voltage total harmonic distortion (THD) values obtained from numerical voltage spectrum calculations (measurements). Motivated by IEEE Standard 519, a part of the multilevel research community uses a limited harmonic count to evaluate the multilevel voltage quality. First, this causes significant voltage THD underestimation, particularly for relatively high frequency PWM. Second, for a three-phase star-connected balanced load with an isolated neutral and phase symmetric modulation strategy, the calculated load line and phase voltage THD become different. However, simple considerations show that line and phase voltage THDs are essentially the same in this case. It may be difficult to judge about the multilevel voltage quality given a numerically calculated (measured) voltage THD value that may be subject to computation errors. Presented are simple smooth hyperbolic voltage THD upper and lower bound approximations for single- and three-phase inverters with nearest synchronous switching. They are valid for arbitrary modulation indices and uniformly distributed level counts and may practically serve as good reference values. [ABSTRACT FROM PUBLISHER]

In this paper, a seven-level single-carrier and multi-modulation-wave sinusoidal pulsewidth modulation (SCMM-SPWM) strategy is proposed. In the negative half cycle of the modulation waves (MWs), dc offsets related to the amplitude of the carrier are set on the three MWs, respectively, to apply the same comparison logics of the MWs and carrier during positive and negative half cycles of the MWs. Thus, it is implemented with only one digital signal processor chip without any other attached logical circuit or controller. The reason for generating the zero-crossing voltage pulse disturbance (ZCVPD) in this strategy is analyzed, and the elimination of the ZCVPD is proposed and verified by experimental results. The spectral characters of the conventional multi-MW-based SPWM and the proposed one are originally derived and compared with each other by simulation in detail. The theoretical analysis, simulation, and experimental results indicate that the output characters of the proposed strategy are identical to those of the conventional one; it means that the proposed strategy can replace the conventional one while with the benefit of significantly reducing the cost and bulk of the implemental platform. [ABSTRACT FROM PUBLISHER]

Three-level topologies are widely used in back-to-back converters of wind turbine generation (WTG) systems. In comparison with a conventional two-level topology, three-level topologies have more advantages, particularly for the high power. Neutral-point clamped (NPC) and T-type are typical three-level topologies. An open-switch fault of a three-level rectifier that is connected to a permanent-magnet synchronous generator (PMSG) leads to the current distortion and torque vibration in WTG systems. Furthermore, WTG systems can break down in the worst case. Therefore, a tolerance control for open-switch faults is required to improve the reliability of WTG systems. WTG systems by applying the tolerance control can be stopped safely and prevent additional problems. Depending on the situation, it can keep the operation of WTG systems under open-switch fault. The effects of outer open-switch faults of three-level rectifiers are analyzed by considering PMSG specifications in this paper. Moreover, a tolerance control for outer open-switch faults of the NPC and T-type three-level rectifiers are proposed with existing tolerance controls for inner open-switch faults. The proposed tolerance control is to inject the exact $d$-axis current value to eliminate current distortion. The simulation and experiment are conducted to prove the feasibility of the proposed tolerance control and to identify its performance. [ABSTRACT FROM PUBLISHER]

In this paper, a new single-phase cascaded multilevel inverter is proposed. This inverter is comprised of a series connection of the proposed basic unit and is able to only generate positive levels at the output. Therefore, an H-bridge is added to the proposed inverter. This inverter is called the developed cascaded multilevel inverter. In order to generate all voltage levels (even and odd) at the output, four different algorithms are proposed to determine the magnitude of dc voltage sources. Reduction in the number of power switches, driver circuits, and dc voltage sources is the advantage of the developed single-phase cascaded multilevel inverter. As a result, the installation space and cost of the inverter are reduced. These features are obtained by the comparison of the conventional cascaded multilevel inverters with the proposed cascaded topology. The ability of the proposed inverter to generate all voltage levels (even and odd) is reconfirmed by using the experimental results of a 15-level inverter. [ABSTRACT FROM PUBLISHER]

The industrial use of inductive power transfer (IPT) systems is becoming widespread, ranging from monorail systems, motors, people movers, and battery charging applications. This paper proposes a 3-D IPT system driven by a multiple-phase power converter. This is aided by spice circuitry simulation of the power converter, finite-element-assisted software magnetic frequency analysis, and via implementation of the proposed system. The proposed system consists of a cubic power transfer primary window generated by a rotating magnetic flux flow path. This rotating field is loosely coupled via magnetomotive force (MMF) induction into a secondary power pick-up. The system has been demonstrated as a low-power battery charging system. [ABSTRACT FROM PUBLISHER]

One of the most important power quality issues is related to current harmonics generated by nonlinear loads such as diode and thyristor front-end rectifiers. Well-established solutions to overcome this problem, such as active power filters (APFs), have the required high power rating components as a major disadvantage. An alternative, called hybrid power filter (HPF), mixes low power rating active filters with passive filters. Unfortunately, many of these HPF topologies have, as a common disadvantage, a great number of passive components and/or transformers. Based on this fact, new concepts of HPFs, consisting of small-rated inverters and $LC$ filters, have been introduced with wide acceptance. The advantage comes from the fact that these HPFs are connected to the grid without any matching transformer. Recently, some topologies based on dual-converter configurations have been shown to be very attractive, where the APF (or HPF) must deal with highly nonlinear loads with high values of $di/dt$ and supplying the reactive power together with harmonic compensation. On the other hand, the drawback of dual converters is the high number of switch devices. Therefore, this paper proposes a transformerless HPF based on a new six-switch two-leg inverter with an enhanced harmonic compensation capability. Aside from presenting a reduced number of switches when compared with dual topologies, the proposed solution is capable of providing fully compensation even for loads with high harmonic content. Experimental results are presented for an HPF inverter prototype in order to demonstrate that the harmonic compensation performance meets the IEEE 519 standard. [ABSTRACT FROM PUBLISHER]

A new space-vector-based sigma delta modulation scheme for any general $N$-level voltage source inverter is proposed in this paper, which directly quantizes the reference space vector. The proposed scheme uses the sigma delta modulation with the quantizer implemented by the proposed space vector quantizer. A new scheme is proposed for directly quantizing the reference space vector to the multilevel inverter switching vectors without mapping it into two-level inverter vector space. Voronoi regions of the multilevel inverter vector space in the proposed space vector quantizer are defined as a parallelogram with the inverter switching vectors as its vertices. The property of the integer values of the inverter switching vectors in 60 ^{\circ} coordinates is utilized for the direct vector quantization of the instantaneous reference voltage space vector. The proposed scheme is implemented for five-level inverters realized by an open-end-winding induction motor fed with two three-level inverters from either side having symmetrical dc-link voltages, and results are presented. [ABSTRACT FROM PUBLISHER]

This paper presents an analytical method that makes it possible to define the pulsewidth modulation (PWM) supply output voltage spectral content, particularly the harmonic phase sequences, without switching instant determination. The results obtained from these developments lead to define a PWM control strategy that allows deleting some switching harmonics in order to reduce undesirable effects. Numerical studies and experiments confirm the theoretical approach and this harmonic control strategy. [ABSTRACT FROM PUBLISHER]

This paper presents a bidirectional current-fed parallel resonant push–pull inverter (CFPRPI) for contactless energy conversions. In conventional CFPRPIs, each switch is in series with a blocking diode. Direct zero voltage switching (ZVS) is proposed to remove the series blocking diodes for higher efficiency and boosting ratio. In addition, the modified inverter has bidirectional power flow capability when these blocking diodes are omitted. Resonant tuning of the system is investigated by using a phase-locked loop and a new self-oscillating switching technique (SST). By using the new SST, the inverter has direct ZVS in a wide range of operating frequencies, which is necessary for inductively coupled power transfer systems. Finally, a laboratory prototype with an input voltage of 12 V and a maximum output power of 60 W has been implemented. [ABSTRACT FROM PUBLISHER]

The term dead time refers to a prime safety factor for most power electronic converter topologies, and it is included either in the control software or in the gate/base driver hardware, depending on the application as well as the control requirements. In this paper, the authors present a comprehensive numerical analysis of dead-time effects on the output voltage of a three-level neutral-point-clamped (NPC) inverter. To incorporate the dead-time effect in the output voltage, 3-D models of three-level carrier pulse width modulation (PWM) methods are modified for two dead-time implementations. Closed-form expressions of inverter phase voltage harmonics for phase opposition disposition (POD) PWM are derived based on the double Fourier series approach and modified contour plots. The harmonic spectra from numerical evaluations, simulations, and experiments for natural sampling (NS), symmetrical regular sampling (SRS), and asymmetrical regular sampling (ARS) are compared to validate the mathematical models. In addition, the fundamental voltage with respect to the dead time and the load phase angle is presented based on analytical results and simulation. [ABSTRACT FROM PUBLISHER]

This paper presents a novel combined-synchronous-rectifier high-frequency-link (CSR-HFL) inverter. Three types of conventional HFL inverters are analyzed and their performance is summarized. According to one of the conventional HFL inverters, i.e., cycloconverter-type HFL (CHFL) inverter, a combined rectifier topology is deduced. To prevent a shorted circuit, two additional switches are used in the new topology. The operation mode of the CSR-HFL inverter is analyzed and the mathematical relationships are given. The difference and correlation, and advantages and disadvantages, are analyzed between the CSR-HFL inverter and the conventional HFL inverter. The relevant grid-connected inverter, ac/ac converter, and full-wave CSR-HFL inverter are also given. The experimental results verify that the proposed CSR-HFL inverter has excellent performance and high efficiency. [ABSTRACT FROM PUBLISHER]

In this paper, a new single-phase cascaded multilevel inverter based on novel H-bridge units is proposed. In order to generate all voltage levels (even and odd) at the output, nine different algorithms are proposed to determine the magnitudes of dc voltage sources. Then, the proposed algorithms are compared to investigate their advantages and disadvantages. This topology is able to increase the number of output voltage levels by using a lower number of power electronic devices such as switches, power diodes, driver circuits, and dc voltage sources that lead to reduction in installation space and cost of the inverter. In addition, in the proposed cascaded multilevel inverter, not only the number of required power electronic devices is reduced, but also the amount of the blocked voltage by switches, and the number of different voltage amplitudes of the used sources is decreased. These features are some of the most important advantages of the proposed topology. These features are obtained via the comparison of the proposed topology and its proposed algorithms with the conventional cascaded multilevel inverters that have been presented in the literatures. The operation and performances of the proposed topology with its presented algorithms in generating all voltage levels have been verified by using the experimental results of a 49-level single-phase inverter. [ABSTRACT FROM PUBLISHER]

The quasi-Z-source cascaded multilevel inverter (qZS-CMI) presented many advantages over conventional CMI when applied in photovoltaic (PV) power systems. For example, qZS-CMI provides the balanced dc-link voltage and voltage boost ability, saves one-third modules, etc. However, current research studies only disclosed control of single-phase qZS-CMI-based PV power systems, and there was no literature related to control of three-phase qZS-CMI-based PV power systems. In this paper, for the first time, three-phase qZS-CMI's control is proposed and demonstrated for application to PV power systems. The models of PV-panel-fed qZS H-bridge module and qZS-CMI-based PV power system are built to accurately design control algorithms for each module and the whole system. The proposed control method includes the distributed maximum power point tracking for each module, dc-link peak voltage balance control for all modules, and grid-tie control for the whole system; moreover, a new multilevel space vector modulation method is proposed for the three-phase qZS-CMI. Simulation and experimental results on a test bench with a three-phase seven-level qZS-CMI-based PV power system verify the proposed control and modulation methods. [ABSTRACT FROM PUBLISHER]

The objective of this paper is to propose a new inverter topology for a multilevel voltage output. This topology is designed based on a switched capacitor (SC) technique, and the number of output levels is determined by the number of SC cells. Only one dc voltage source is needed, and the problem of capacitor voltage balancing is avoided as well. This structure is not only very simple and easy to be extended to a higher level, but also its gate driver circuits are simplified because the number of active switches is reduced. The operational principle of this inverter and the targeted modulation strategies are presented, and power losses are investigated. Finally, the performance of the proposed multilevel inverter is evaluated with the experimental results of an 11-level prototype inverter. [ABSTRACT FROM PUBLISHER]

In this paper, a predictive control scheme is proposed for the low-voltage ride-through (LVRT) enhancement of direct-driven permanent-magnet-synchronous-generator-based megawatt-level wind turbines. The proposed method uses the turbine–generator rotor inertia to store the surplus energy during the grid voltage dips. The power conversion system is realized using a three-phase diode-bridge rectifier, a three-level-boost converter, and a neutral-point-clamped (NPC) inverter. The wind turbine requirements, such as maximum power point tracking, net dc-bus voltage control, balancing of the dc capacitor voltages, and reactive power generation, are modeled as the reference control variables. The generator- and grid-side cost functions are defined to deal with these control objectives. During each sampling interval, the control goals are achieved based on the minimization of cost functions. The coordination of boost and NPC converters and the exchange of reference control variables during normal and LVRT operation are formulated such that the power converters operate in a safe mode while meeting the grid code requirements. Simulation and experimental results are presented to validate the proposed strategy. [ABSTRACT FROM PUBLISHER]

In a six-switch three-phase inverter, the conventional pulsewidth modulation (PWM) has six switching times in every switching period based on the average concept. The used multidimensional feedback quantized modulation (MDFQM) strategy selects one switching state and keeps it in every sampling period based on the minimization of filtered voltage errors between the desired voltage commands and the output voltages. The widths of the output voltage pulse are integer times the fixed sampling time in MDFQM. In this paper, two high-efficiency current control methods based on MDFQM are proposed. They integrate the MDFQM strategy and the current control function to minimize the filtered current errors between the desired current commands and the inverter current. Due to the main advantages of less switching numbers and more closed fundamental current, a high-efficiency performance is achieved. The proposed methods are applied to the current control of a three-phase permanent-magnet synchronous motor. The simulation results and experimental results verify the effectiveness of the proposed methods. [ABSTRACT FROM PUBLISHER]

This paper presents a novel control method for a current-fed full-bridge inverter actuating an ultrasonic piezoelectric transducer (PT). In the conventional ultrasonic detection system, the PT has maximum transmitting gain at its series resonance frequency while having maximum receiving gain at its parallel resonance frequency. With the proposed approach, the PT could have maximum transmitting gain at the parallel resonance frequency and this frequency can be automatically traced, and hence adapted, to the environmental variation. A prototype circuit was constructed to verify the proposed control method. The experimental results show that the receiving voltage signal could have a maximum value at the parallel resonance frequency, and the traced frequency is 0.04 kHz higher than the parallel resonance frequency. [ABSTRACT FROM PUBLISHER]

Inverters play key roles in motor drives, flexible power transmissions, and recently grid-tied renewable energy generation units. Therefore, availability and reliability of inverters have become increasingly important. Following early stage fault detections in inverters, remedial actions can extend normal operation of inverters and, in some cases, derate the system to prevent unexpected shutdowns. A remedial action typically contains a combination of hardware and software reconfigurations. The main purpose of this paper is to provide an instructive survey of existing fault-tolerance (remedial) techniques for three-phase, two-level, and multilevel inverters. [ABSTRACT FROM PUBLISHER]

Low leakage current and high efficiency are two key indexes for the transformerless photovoltaic (PV) grid-connected inverter. The transformerless inverter topologies have superior efficiency owing to saving the transformer, but their switches are still on a hard-switching state at present. This paper presents a novel zero-voltage transition (ZVT) concept for the full-bridge transformerless PV grid-connected inverter topologies. The zero-voltage turn-on and turnoff of the high-frequency main switches and the zero-current turn-on of the auxiliary switches, as well as the zero-voltage turn-on and turnoff of the antiparallel diodes of the line-frequency switches, are realized by introducing two resonant tanks. Take ZVT-H6-I for example. The operation principle, soft-switching conditions, duty cycle restriction, and parameter design rule of the resonant tank are analyzed in detail. Finally, the validity of the ZVT concept is verified by a ZVT-H6-I prototype rated at 100 kHz and 1 kW. [ABSTRACT FROM PUBLISHER]

This paper introduces a fault detection and isolation (FDI) method for faulty metal–oxide–semiconductor field-effect transistors in a three-phase pulsewidth-modulated (PWM) voltage source inverter. Short-circuit switch faults are the leading cause of failure in power converters. It is extremely vital to detect them in the early stages to prevent unwanted shutdown and catastrophic failures in motor drives and power generation systems. Against the common FDI methods for power electronic inverters that use phase currents and PWM gate control signals, the proposed method only uses the inverter output voltages. This method analyzes the PWM switching signals in a time-free domain that is called the voltage space. For a healthy inverter, the projection of the state transitions in the voltage space results in a cubic pattern. Each short-circuit switch fault uniquely changes the voltage-space pattern that allows isolating the faulty switch. The fault detection time is only within one PWM carrier period, which is significantly faster than current-based conventional methods. The FDI result does not depend on the load, the PWM switching frequency, and the feedback loop. This method can address the reliability problem of multilevel inverters in renewable electrical generation systems and can dramatically reduce the number of required sensors. [ABSTRACT FROM PUBLISHER]

This paper presents a finite control set model predictive strategy and its application to the load voltage control of two-level four-leg inverters. The proposed approach uses the novel discrete-time model of the inverter and output $LC$ filter in order to predict the variables to be controlled. These predictions are carried out for the 16 switching states of the inverter and are evaluated using a cost function. The switching state that forces the load voltages to be closest to their respective references is chosen and applied to the inverter. The behavior of the predictive controller has been investigated, and the changes to both inductive and capacitive filter parameters have been considered. In order to improve the reliability of the fourth leg as well as the overall inverter efficiency, a solution is proposed, which combines hardware and software reconfigurations. The feasibility of the proposed method is verified through simulation and experimental results considering single-/three-phase, balanced/unbalanced, and linear/nonlinear loads. [ABSTRACT FROM PUBLISHER]

The voltage range of a renewable energy source, such as the photovoltaic cell, is influenced by the environment, light, temperature, and so on. The power conditioning system should adapt to the wide input voltage and have buck–boost ability. Based on the structure of the “ac/ac unit,” this paper presents a novel active buck–boost inverter (ABI) topology suitable for wide-range input, which can realize buck–boost conversion in a quasi-single-stage inverter. The ac/ac unit composed of active switches is utilized to perform voltage boost without introducing additional passive elements, which is in favor to the system power density and efficiency. Operational analysis in buck and boost modes are presented, and the modulation strategy applied in the ABI is also developed. Simulation and experimental results are presented to verify the operational principle and its modulation strategy. [ABSTRACT FROM PUBLISHER]

In this paper, two new topologies are proposed for multilevel inverters. The proposed topologies consist of a combination of the conventional series and the switched capacitor inverter units. The proposed topologies reduce the number of switches and isolated dc voltage sources, the variety of the dc voltage source values, and the size and cost of the system in comparison with the conventional topologies. In addition, the proposed topologies can double the input voltage without a transformer. There is no need for complicated methods to balance the capacitor voltage. The simulation and experimental results of single-phase 25- and 17-level inverters are given to prove the correct operation of the proposed topologies. [ABSTRACT FROM PUBLISHER]

High-boost dc-ac inverters are used in solar photovoltaic (PV), fuel cell, wind energy, and uninterruptible power supply systems. High step-up and step-down capabilities and shoot-through immunity are some of the desired properties of an inverter for a reliable, versatile, and low-distortion ac inversion. The recently developed Z-source inverter (ZSI) possesses these qualities. However, the realization of ZSI comes at a cost of higher passive component count as it needs two sets of passive filters. A switched boost inverter (SBI) has similar properties as ZSI, and it has one L\-C pair less compared to ZSI, but its gain is less than ZSI. This paper proposes the current-fed switched inverter (CFSI) which combines the high-gain property of ZSI and low passive component count of SBI. The proposed inverter uses only one L\-C filter and three switches apart from the inverter structure. The inverter topology is based on current-fed dc/dc topology. Steady-state analysis of the inverter is presented to establish the relation between the dc input and the ac output. A pulse width modulation (PWM) control strategy is devised for the proposed inverter. An experimental prototype is built to validate the proposed inverter circuit in both buck and boost modes of operation. A 353-V dc-link and a 127 V (rms) ac are obtained from a 35.3-V dc input to demonstrate the boost mode of operation. A 200-V dc-link and a 10.5-V (rms) ac are obtained from a 37.8-V dc input to verify the buck mode of operation of CFSI. [ABSTRACT FROM PUBLISHER]

This paper describes an optimal configuration for multicentral inverters in a medium-voltage (MV) grid, which is suitable for large-scale photovoltaic (PV) power plants. We theoretically analyze a proposed common-mode equivalent model for problems associated with multicentral transformerless-type three-phase full bridge (3FB) PV inverters employing two-winding MV transformers. We propose a synchronized pulse width modulation (PWM) control strategy to effectively reduce the common-mode voltages that may simultaneously occur. In addition, we propose that the existing 3FB topology may also have the configuration of a multicentral inverter with a two-winding MV transformer by making a simple circuit modification. Simulation and experimental results of three 350 kW PV inverters in a multicentral configuration verify the effectiveness of the proposed synchronization control strategy. The modified transformerless-type 3FB topology for a multicentral PV inverter configuration is verified using an experimental prototype of a 100 kW PV inverter. [ABSTRACT FROM PUBLISHER]

This paper presents a division-summation (D-\Sigma) digital control for a three-phase inverter to achieve active and reactive power injection to the ac grid. The proposed D-\Sigma approach summarizes the inductor-current variations over one switching cycle to derive control laws directly, which can overcome the limitation of d–q transformation. The inverter with this control can achieve various power factors (PFs) leading or lagging, by taking into account wide filter-inductance variation and grid-voltage distortion, reducing core size significantly. The control laws for achieving the desired features are derived in detail, and they are expressed in general forms for readily software programming. With the enhancement work of previous research, active and reactive power injection with PF from 0 to 1 can be controlled effectively, so that these control laws can be extended to wide current-tracking applications, such as static synchronous compensator and active power filter. In the design and implementation, the inductance values corresponding to various inductor currents were measured at the startup and stored in the controller for scheduling loop gain cycle by cycle. Measured results from a 10-kVA 3 \phi inverter have confirmed the analysis and discussion of the proposed control approaches. [ABSTRACT FROM PUBLISHER]

The high-power voltage source inverters are switched at low frequency to reduce the losses in the inverter. The discontinuous pulsewidth-modulation (PWM) sequences reduce the switching frequency to two-thirds compared to the conventional continuous PWM sequences. At low switching frequency, the output will be rich in harmonics, and synchronization is a must to avoid subharmonics. This paper presents four basic types of synchronized discontinuous PWM (DPWM) sequences that ensure synchronization, three-phase symmetry, and half-wave symmetry. The proposed synchronized DPWM sequences are verified through simulation and experiment on a constant- v/f open-loop induction motor drive. The performance of the proposed DPWM algorithms is studied in the entire modulation region, including the overmodulation region, and is compared with that of the conventional synchronized space vector PWM. A different type of DPWM with low common-mode voltage is suggested for low-modulation region and verified experimentally. [ABSTRACT FROM PUBLISHER]

In this paper, a new general cascaded multilevel inverter using developed H-bridges is proposed. The proposed topology requires a lesser number of dc voltage sources and power switches and consists of lower blocking voltage on switches, which results in decreased complexity and total cost of the inverter. These abilities obtained within comparing the proposed topology with the conventional topologies from aforementioned points of view. Moreover, a new algorithm to determine the magnitude of dc voltage sources is proposed. The performance and functional accuracy of the proposed topology using the new algorithm in generating all voltage levels for a 31-level inverter are confirmed by simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents a multilevel inverter that has been conceptualized to reduce component count, particularly for a large number of output levels. It comprises floating input dc sources alternately connected in opposite polarities with one another through power switches. Each input dc level appears in the stepped load voltage either individually or in additive combinations with other input levels. This approach results in reduced number of power switches as compared to classical topologies. The working principle of the proposed topology is demonstrated with the help of a single-phase five-level inverter. The topology is investigated through simulations and validated experimentally on a laboratory prototype. An exhaustive comparison of the proposed topology is made against the classical cascaded H-bridge topology. [ABSTRACT FROM PUBLISHER]

An architecture of multiple-integrated converter modules sharing an unfolding full-bridge inverter with a pseudo dc link (MIPs) is proposed for grid-connected photovoltaic systems in this paper. The proposed configuration can improve the power conversion, the control circuit complexity, and the cost competitiveness. The proposed MIP is composed of distributed flyback dc–dc converters (DFCs) and an unfolding full-bridge inverter with an ac filter. The DFCs can eliminate the shading effect by using the individual maximum power point tracking. In conventional flyback-type single-phase utility-interactive inverters, discontinuous conduction mode and boundary conduction mode are popular because of the inherent constant current-source characteristics more desirable for grid connection and of the simple procedures for the controller design. However, the operating mode suffers from a large current stress of the circuit components, which leads to the low power efficiency. To avoid this, the DFCs operate under continuous conduction mode that allows reduced current stresses and increased power efficiency, as well as low material cost. The current control loop of the converters employs primary-side regulation contributing to improvement of dynamics as well as the cost reduction significantly due to the elimination of the high-linearity photocoupler device. Development of a new dc-current loop that maintains the level of dc-current injection into the grid within the levels stipulated by IEEE 1547 will be dealt as well. The performance validation of the proposed design is confirmed by experimental results of a 200-W hardware prototype. [ABSTRACT FROM PUBLISHER]

In this paper, a model predictive scheme is proposed to control the grid-connected high-power four-level diode-clamped inverter. To predict the future behavior of active and reactive grid power values and dc link capacitor voltages, a discrete-time model of the inverter is developed in synchronous reference frame. The controller uses all the possible switching states of the inverter for the prediction and evaluates them using a cost function. The switching state, which minimizes the cost function, is then chosen and applied at the next sampling interval. The switching frequency minimization is also achieved by including an extra constraint in the cost function. A simplified extrapolation method with reduced computational burden is proposed to safeguard the semiconductor devices during the dynamic changes in reference power values. The performance of the proposed method is investigated with the perturbations in the grid filter and dc link parameters. The feasibility of the proposed method is verified through simulation and experimental results, showing good dynamic and steady-state performance. [ABSTRACT FROM PUBLISHER]

Loads connected to a stiff source cannot be protected from voltage disturbances using a distribution static compensator (DSTATCOM). In this paper, a new control-algorithm-based multifunctional DSTATCOM is proposed to operate in voltage control mode under stiff source. This scheme provides fast voltage regulation at the load terminal during voltage disturbances and protects critical loads. In addition, during normal operation, the generated reference load voltages allow control of the source currents. Consequently, DSTATCOM injects reactive and harmonic components of load currents to make source power factor unity. Simulation and experimental results are presented to verify the efficacy of the proposed control algorithm and multifunctional DSTATCOM. [ABSTRACT FROM PUBLISHER]

Induction heating systems are the technology of choice in many industrial, domestic, and medical applications due to its high performance. The core component of such systems is the power supply, which is usually composed of a rectifier stage and a resonant inverter. In order to simplify and further optimize the performance of the power supply, a class-E direct ac–ac converter featuring multicycle modulations is proposed in this paper. The proposed converter is composed of two switching devices that enable the direct ac–ac conversion. Single- and multicycle operation modes have been analytically described to prove the benefits, in terms of peak voltage reduction and output power control capabilities. A prototype featuring SiC junction-gate field-effect transistor devices, which perfectly fit these applications, has been designed and built to prove the feasibility of the proposed converter. The experimental results match the analytical results and validate the benefits of this converter. [ABSTRACT FROM PUBLISHER]

This paper analyzes a high-power (100-kW) high-frequency (50-kHz) voltage-fed inverter with a series resonant load circuit for industrial induction heating applications which is characterized by a full-bridge inverter composed of isolated-gate bipolar transistors and a new power control based on phase-shift (PS) control. This power control circuit incorporates a load-adaptive variable-frequency controller and automated blanking time management in order to allow the inverter to work in zero-voltage switching for all output power levels and load conditions. An important improvement of the inverter reliability is achieved by choosing an appropriate and novel switching sequence for the PS inverter. The results are verified experimentally using a prototype for induction hardening applications. A comparative study between the proposed and standard PS power control will be made. [ABSTRACT FROM PUBLISHER]

A novel soft-switching high-frequency (HF) resonant (HF-R) inverter for induction heating (IH) applications is presented in this paper. By adopting the current phasor control of changing a phase shift (PS) angle between two half-bridge inverter units, the IH load resonant current can be regulated continuously under the condition of wide-range soft-switching operations. In addition to this, the dual-mode power regulation scheme-based PS angle control and asymmetrical pulsewidth modulation in one inverter unit is proposed for improving the efficiency in low output power settings. The essential performances on the output power regulation and soft-switching operations are demonstrated in an experiment using its 1-kW 60-kHz HF-R inverter prototype, and then, the topological validity is evaluated from a practical point of view. [ABSTRACT FROM PUBLISHER]

This paper presents a tunable self-oscillating switching (TSOS) technique for current source parallel resonant inverters. Using this technique, the inverter has lower voltage stress in comparison with conventional methods such as phase-locked loop (PLL) circuits or integral controllers. The new switching technique instantly tracks the variation of resonant frequency. In addition, the TSOS has the capability of phase error tuning which is essential for parallel operation and zone control induction heating systems. The TSOS method has simple structure and operates in wide range of frequencies. Hence, the inverter can be utilized as a general-purpose inverter to supply different coils, loads and self-switched capacitor banks. The dynamics of the new tuning system is compared with the PLL method in transient conditions. A laboratory prototype with operating frequency of 25–100 kHz is implemented to verify the performance of the new tuning system. [ABSTRACT FROM PUBLISHER]