Search

In this paper, a dc-link voltage protection (DCVP) control method is proposed to address the dc-link overvoltage issue due to power backfeeding in a parallel uninterruptible power supply (UPS) system. The proposed control method is able to protect the inverter against the excessive dc-link voltage, which increases the system reliability and robustness. Moreover, a current sharing control strategy is proposed by online regulating the virtual resistance of each UPS module. The proposed current sharing control strategy is able to address the circulating fundamental and harmonic currents caused by the line impedance mismatching or power backfeeding issue in the UPS system. In addition, an improved consensus-based distributed controller is proposed to alleviate the overshoot issue during the transient process in voltage amplitude and frequency restoration. Finally, the feasibility of the proposed methods is verified by experimental results from the parallel UPS prototypes. [ABSTRACT FROM PUBLISHER]

This paper aims to investigate a disturbance-rejection-based model predictive control (MPC) with two flexible modes (i.e., unconstrained mode and constrained mode) for three-phase inverters with an $LC$ filter. A disturbance observer (DOB) is designed to both simplify the prediction model and achieve the robustness against uncertain parameters. First, the unconstrained mode is designed with a simple horizon-one MPC control law to precisely regulate the output voltage in the steady state. Next, the constrained mode is designed with long-horizon MPC to quickly drive the system to the unconstrained mode by further optimizing the modulation stage. Also, the proposed MPC ensures the robustness and optimality in all operating modes. Especially, the overall closed-loop stability with DOB dynamics is proven by using Lyapunov function. Unlike other MPC methods, the long-horizon MPC in the constrained mode is specialized by finite switching sequences of the sector-based space vector modulation. Comparative studies with the conventional linear quadratic regulator are conducted on a prototype test bed with a TI TMS320F28335 DSP. Then, the proposed MPC method verifies fast dynamic response and advanced voltage regulation (i.e., small steady-state errors and low total harmonic distortion) under various load conditions and uncertain parameters. [ABSTRACT FROM AUTHOR]

Several applications such as power supplies for electric precipitators, ozone generation, partial discharge, etc., require ac superimposed dc (ACsDC) voltage supply. Most of such applications use intransigent systems for producing ACsDC voltages. In this paper, three different kinds of flexible power electronic converters are proposed for producing ACsDC voltages. These converters have two power conversion stages: input and output. In the input stage, two isolated dc voltages are obtained by using an isolated three-port dc–dc converter or two isolated two-port dc–dc converters. In the output stage, one of the input-stage dc voltages is used to generate an ac voltage and the obtained ac voltage is added to the remaining input-stage dc voltage to obtain an ACsDC voltage. Based on the converters used in the input stage, the proposed ACsDC converters are named as a dual active bridge (DAB) converter-based ACsDC converter (DAB-ACsDC), triple port active bridge (TAB) converter-based ACsDC converter (TAB-ACsDC), and dual transformer-based asymmetrical triple port active bridge (DT-ATAB) converter-based ACsDC converter (DTATAB-ACsDC). A detailed analysis of these ACsDC converters and their verifications using simulations and experimental studies are presented, which depict that the proposed converters can be used effectively for producing ACsDC voltages. [ABSTRACT FROM AUTHOR]

Compared with multilevel space vector modulation, level-shifted multicarrier sinusoidal pulsewidth modulation (SPWM) for nested neutral point-clamped (NNPC) inverters requires much less calculations and implementation efforts, but the existing conventional SPWM cannot suppress the severe flying-capacitor (FC) voltage ripples under low output-frequency conditions. In order to solve this problem, a multicarrier-based PWM strategy with complete voltage balance control (VBC) capacity is proposed in this paper. For NNPC inverters operating under low output-frequency conditions, two preprocessing steps, the zero-sequence injection and the modulation-signal rearrangement, are proposed before the comparisons between level-shifted carriers and modulating signals. These preprocessing steps make the average currents flowing through FCs zero, which is beneficial to greatly reduce the FC voltage ripples under low output-frequency conditions. Together with additional VBC, the proposed modulation can assure the FC voltages balanced under the entire output-frequency conditions. Principles and implementation processes of proposed modulation techniques and VBC methodsare elaborated in detail and compared with conventional modulation methods. Both simulation results from a 5-MVA system and experimental results based on a 5-kVA platform are presented to verify the effectiveness. [ABSTRACT FROM AUTHOR]

Two main problems, including unbalanced grid input and circuit parameters uncertainty in the three-phase soft-switching converter control system, are considered in this paper. First, the constant-switching-frequency model-predictive control (CF-MPC) is improved for application in compound active-clamp zero-voltage-switching three-phase power factor correction converter. Second, a robust-constant-frequency model-predictive control (RCF-MPC) method is proposed for current loop; the novel contributions are: 1) the negative-sequence current component is introduced into the cost function of the model-predictive control to decrease the influence of unbalanced grid input; and 2) a robust item is added into the predictive model to reduce the influence of the circuit parameter uncertainty. Third, a robust variable structure controller is proposed for voltage loop considering the capacitor and load uncertainty. The simulation and experiment results show that, compared with the original CF-MPC method and the traditional proportional–integral control method, the proposed RCF-MPC method decreases the total harmonic distortion under the unbalanced grid condition. Meanwhile, the voltage loop robust variable structure controller has better transient and steady-state performance with respect to the load perturbation. [ABSTRACT FROM PUBLISHER]

A fixed switching period sliding mode control (SMC) for permanent-magnet synchronous machines (PMSMs) is presented. The aim of this paper is to design an SMC that improves the traditional PI-based field-oriented control transient response, as well as to reduce the switching frequency variations of the direct torque control. Such SMC requires a decoupling method of the control actions, which also brings constant switching functions slopes. These constant slopes allow to calculate the required hysteresis band value to control the switching frequency. The digital implementation degrades the performance of the hysteresis comparator, and as a consequence, the previously calculated band becomes inaccurate to regulate the switching frequency. In order to recover the analogue hysteresis band comparator performance, a predictive algorithm is proposed. Finally, a set of experimental results with constant switching frequency during a torque reversal and speed control tests are provided. [ABSTRACT FROM PUBLISHER]

This paper proposes a high-efficiency two-stage three-level grid-connected photovoltaic (PV) inverter. The proposed two-stage inverter comprises a three-level step-up converter and a three-level inverter. The three-level step-up converter not only improves the power-conversion efficiency by lowering the voltage stress but also guarantees the balancing of the dc-link capacitor voltages using a simple control algorithm; it also enables the proposed inverter to satisfy the VDE 0126-1-1 standard of leakage current. The three-level inverter minimizes the overall power losses with zero reverse-recovery loss. Furthermore, it reduces harmonic distortion, the voltage ratings of the semiconductor device, and the electromagnetic interference by using a three-level circuit configuration; it also enables the use of small and low-cost filters. To control the grid current effectively, we have used a feed-forward nominal voltage compensator with a mode selector; this compensator improves the control environment by presetting the operating point. The proposed high-efficiency two-stage three-level grid-connected PV inverter overcomes the low efficiency problem of conventional two-stage inverters, and it provides high-power quality with maximum efficiency of 97.4%. Using a 3-kW prototype of the inverter, we have evaluated the performance of the model and proved its feasibility. [ABSTRACT FROM PUBLISHER]

In this paper, a new nonisolated high-voltage-gain boost converter is proposed. The proposed converter is constructed by adding an additional inductor to a conventional three-level-boost (TLB) converter. When compared with the conventional boost and TLB converters, the proposed converter can achieve higher voltage conversion ratio with reduced voltage and current stresses in the switches. In particular, the proposed converter can reduce the losses of active devices by reducing the current of the switch compared to conventional converters, thus, can achieve high efficiency. In addition, the proposed converter automatically balances the output voltages for an unbalanced load without the need for any additional control strategy or auxiliary circuit. A 2-kW prototype converter was built and tested to verify performances of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, we propose a Lyapunov-function-based controller for the flyback converter operating in the continuous conduction mode (CCM). The controller consists of a duty-ratio feedforward control unit and a Lyapunov-function-based feedback control unit. The duty-ratio feedforward signal is used to reduce the burden from the Lyapunov feedback controller. The control system guarantees global exponential stability of the closed-loop system and, hence, offers fast transient response under large-signal perturbations. In constructing the controller, we use the average model of the flyback CCM converter taking the parasitic components into account. Numerical simulations confirmed its superior performance, and experimental tests validated the proposed control approach. [ABSTRACT FROM PUBLISHER]

In this paper, a power factor correction (PFC)-based switched reluctance motor (SRM) drive is proposed. Generally, the SRM drive is fed with a simple diode bridge rectifier followed by a bulky capacitor, which draws peaky current at low power factor and high-input-current total harmonic distortion (THD). Here, a dual output converter is proposed to control the SRM and to provide power quality improvement as well. This converter is a combination of Cuk and SEPIC converters, which produces two equal output voltages with neutral point N, to feed a midpoint converter of the SRM drive. The converter is designed to operate in discontinuous conduction mode of operation to obtain inherent PFC at supply side. The motor control is attained by regulating dc link voltage over a wide range. Test results on a prototype of the SRM drive demonstrate the excellent performance with high power factor and reduced input current THD. The observed power quality indices depict the improved power quality as per the standard IEC 61000-3-2. [ABSTRACT FROM PUBLISHER]

The parallel three-phase grid-connected converters sharing dc and ac bus can increase the system power level effectively. However, the circulating current will occur inevitably. The existing studies primarily focus on dc, fundamental, and low-frequency circulating current. The high-frequency circulating current (HFCC) caused by asynchronous carriers is studied emphatically in this paper, which is based on the analysis of the change of circulating current in one control cycle. A novel method to suppress HFCC caused by asynchronous carriers of modules is proposed. In this method, the carrier period of slave module is adjustable and the carrier period of the master module is constant. When a large phase shift between modules occurs, an adjusting cycle is inserted to carrier of slave module to realize resynchronizing with master module. It is noted that there is no other commutation between the two modules (expect the dq current reference), such as the carrier information. Finally, the feasibility and effectiveness of the proposed method are verified by experiments. [ABSTRACT FROM PUBLISHER]

Three-level buck dc–dc converters have advantages over the traditional buck converters: half switch voltage stress, doubling effective switching frequency, smaller inductor size, and the higher power density. To benefit from those advantages, the flying capacitor voltage must be balanced at half of the input voltage. Most existing methods of balancing the flying capacitor voltage require current sensing, which increases the cost and noise sensitivity. This paper proposes a novel state-machine structure of second-order sliding-mode (SOSM) control for three-level buck dc–dc converters without sensing currents. With insensitivity to parameter variations of SOSM control, the proposed control approach tackles the strongly coupled problem of output voltage and flying capacitor voltage in three-level buck dc–dc converters. Compared to existing approaches, the controller achieves fast start-up without overshoots, fast load disturbances rejection, and robustness against parameter uncertainties for the output voltage, and balance of the flying capacitor voltage without sensing the current of flying capacitor. The proposed approach is verified with experimental results of a 1.25 V, 2.5 A prototype. [ABSTRACT FROM PUBLISHER]

Conventional hysteresis-modulation-based sliding-mode (SM) controller exhibits a varying switching frequency. Existing SM controllers for achieving constant-switching-frequency operation often have complicated structures and/or are less straightforward to design to meet different steady state, transient, and loading requirements. In this paper, a new direct SM voltage controller based on parabolic modulation (PM) is proposed and applied to a buck converter. The objective is to achieve constant-switching-frequency operation of a switching converter with simple control structure and good operating performance. Both theoretical study and experimental work on a buck converter show that the proposed PM-based SM control can achieve 1) constant switching frequency in the continuous-conduction mode (CCM) and quasi-constant switching frequency in the discontinuous-conduction mode (DCM) of operation, 2) inherent input-disturbances rejection and superior reference tracking performance, and 3) seamless mode transition between CCM and DCM. [ABSTRACT FROM PUBLISHER]

This paper proposes a single-stage light-emitting diode (LED) driver based on an inverted buck topology, using current path control switches. The proposed circuit consists of a control circuit, a bridge diode, and an inverted buck converter with multiple switches connected to the LED segments in parallel. Whereas the typical buck LED driver operates with a fixed LED forward voltage, the proposed driver operates with a variable LED forward voltage, according to the input voltage level. Because of this capability to adjust the LED forward voltage, it can reduce the current ripple and the switching frequency with a small inductance value. In addition, it enables operation with LED lamps of a wide voltage range, while simultaneously achieving small dead-angles. The detailed operation principles are described, and the design considerations for the proposed driver are discussed. The proposed driver circuit and control operation are verified experimentally using a 7 W hardware prototype with four LED segments. The obtained experimental results show that under a 110 Vrms input voltage, the proposed driver achieves a power factor of 0.94 with a small dead-angle and an efficiency of 94%. [ABSTRACT FROM PUBLISHER]

In this paper, a new type of matrix converter (MC) also called a single-phase high-frequency transformer isolated (HFTI) buck MC is proposed. The proposed converter can provide step-down operation of the input voltage with various types of output voltages such as in-phase and out-of-phase output voltages, rectified (or positive) output voltage, and output voltage with step-changed frequency. By incorporating HFT isolation, the proposed MC saves an extra bulky line frequency transformer, which is required for the conventional MCs to provide electrical isolation and safety, when used in application such as dynamic voltage restorers, etc. Two different circuit variations of the proposed HFTI MC are presented with and without continuous output currents, with the latter having less passive components. The safe-commutation strategy is also employed for the proposed HFTI MC to provide current path for the inductor during dead-time, which avoids switch voltage spikes without adding any snubber circuits. The operation principle and circuit analysis of the proposed MC are presented, and switching strategies are also developed to obtain various output voltages. Moreover, a prototype of the proposed MC is fabricated, and experiments are performed to produce in-phase/out-of-phase and rectified output voltages, and output voltage with step-changed frequency. [ABSTRACT FROM PUBLISHER]

This paper presents a new buck–boost converter. Unlike the single-switch buck–boost converter, the proposed converter has low-voltage stresses on semiconductors. Moreover, although both the conventional two-switch buck–boost (TSBB) and the proposed converters have the same number of passive and active components, and the proposed converter can reduce the conduction loss as a result of having fewer conducting components. Therefore, the proposed converter obtained a higher efficiency than the TSBB converter. A 48-V output voltage and 150-W output power prototype was fabricated to verify the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]

To reduce the steady-state torque ripples for permanent-magnet synchronous motor drives with predictive torque control (PTC), this paper proposes a modified PTC algorithm based on the extended control set (ECS-PTC). In the proposed algorithm, more candidate voltage vectors are extended to the control set, which forms the ECS, and then, the torque control precision could be improved and the torque ripples will be reduced. More attractive thing is that a new voltage vector synthesis method is deigned in ECS-PTC, and the corresponding predictive model and cascaded predictive algorithm are set up on the basis of this method. With the help of them, the optimal vector can be selected from ECS in a shorter control period of time, and its amplitude is also optimized at the same time to achieve high-precision control effects for torque and flux. In addition, the three-phase duty ratios of the output vector can be determined in ECS-PTC directly, without the help of space vector pulse width modulation. The experimental results show that ECS-PTC has excellent dynamic torque performance, and it also has more stable torque control performance and better execution efficiency at the same time. [ABSTRACT FROM PUBLISHER]

This paper proposes a digitally implemented charge control for LLC resonant converters. By analyzing the small-signal characteristics of the resonant capacitor, it is revealed that the resonant capacitor has exactly the same functionality as a resettable integrator in the charge control for a PWM converter. Based on the analyzed results, the proposed charge control is implemented simply by sensing the voltage across the resonant capacitor in a switching period. The proposed method features simple implementation with resistive voltage divider and suitability for digital control as well as good performance as other multiloop controls have. The design guideline for the charge controller is given based on the loop gain analysis. Finally, the operation and performance of the proposed method are verified with a 240-W LLC resonant converter. [ABSTRACT FROM AUTHOR]

A fixed-frequency pulse width modulation (PWM) controlled bidirectional current-fed series-resonant converter is proposed in this paper. The proposed bidirectional resonant converter is derived based on integration of a bidirectional boost/buck converter and a dual-active-bridge series-resonant converter. The most attractive feature of the proposed bidirectional resonant converter is that its voltage gain is only determined by the duty cycle of primary-side switches and has nothing to do with the transferred power. Therefore, the direction and amplitude of the transferred power can be easily regulated continuously and smoothly. In addition, with the help of an auxiliary inductor, zero voltage switching can be achieved for all the active switches on both primary and secondary sides within the entire operation range. Furthermore, the converter is suitable for wide voltage applications because its voltage gain can be regulated in a wide range. The operational principles and characteristics of the proposed bidirectional resonant converter are analyzed in detail. The feasibility and effectiveness of the proposed converter are fully verified by the experimental results from a 1.6 kW prototype. [ABSTRACT FROM AUTHOR]

Novel load regulation methods for switched-capacitor converter (SCC) system operating in parallel mode are proposed. SCCs are ready for integrated design which is ideal for mass production and also enables power conversion in compact footprint. At the same time, they are excellent candidates for parallel mode operation since the load current sharing among them is automatically allocated by the inherent droop characteristic, which is determined by the equivalent internal resistance. Instead of controlling the individual switching frequency of SCC units, this paper proposes a number of unit commitment schemes which regulate the output voltage by adjusting the number of activated SCC units. In addition to conventional discrete unit commitment, intermediate number of activated units is realized by employing pulse-dropping pulse width modulation. The proposed methods are verified by simulation and the experiment of a parallel SCC system consists of a number of double-mode zero-current switching SCC units. [ABSTRACT FROM AUTHOR]

Grid-connected power conversion systems for renewable energy sources must fulfill several requirements, e.g., the high efficiency, the reduced cost and complexity, and, quite often, the boost capabilities that is usually achieved using a front-end dc–dc boost converter before the inversion stage, leading to a two-stage architecture. Meanwhile, single-stage power conversion systems, which perform the boosting operation within the inversion one, offer some potential advantages, in terms of reducing the complexity and the volume of the whole system. Among several proposed options, the split-source inverter (SSI) has been recently proposed by Abdelhakim et al. as an alternative option with some interesting features to the commonly used Z-source inverter. Taking into account that the SSI is controlled by a single parameter, i.e., its dc and ac sides are controlled by the modulation index, it is of paramount importance to investigate its control scheme in grid-connected mode, which has never been studied yet. Hence, this paper models the SSI dc side and proposes a modified modulation scheme combined with the commonly used synchronous reference frame control technique to achieve a decoupled control scheme of the SSI in grid-connected mode, i.e., the dc and the ac sides of the SSI can be controlled independently, which is convenient for many applications. The introduced control scheme is analyzed and simulated using a MATLAB/Simulink model, where a reduced scale 1-kVA grid-connected SSI is designed and simulated for the sake of experimental validation. Finally, the designed system is implemented experimentally to validate and verify the reported analysis and simulations. [ABSTRACT FROM PUBLISHER]

This paper presents the design and implementation of a simple neutral point potential (NPP) regulator for a three-level diode-clamped inverter employing a sine-triangle regulator in conjunction with a closed-loop controller with reduced switching losses. The regulator principle is based on adding a continuous variable offset voltage which regulates the midpoint potential of the dc bus. The novelty of the proposed NPP regulator is in the determination of the magnitude of variable offset voltage based upon the average value, peak-to-peak amplitude, total harmonic distortions, and third harmonic content in NPP. Aside from maintaining dc-bus voltage balance, the proposed regulator leads to a significant reduction in the voltage distortion at the NP, resulting in the reduction of the required dc-bus capacitance. It also reduces the switching losses of the inverter by inserting the “no-switching” zone within each half cycle of the fundamental voltage wave. Analytical, computer simulation, and experimental results verifying the approach are presented in this paper for various load power factor angles. [ABSTRACT FROM AUTHOR]

This paper proposes a phase-shift interleaving control method for variable-phase switched-capacitor (SC) converters that can perform voltage conversions with little electromagnetic interference over a wide range of operating condition. This is achieved by having multiple units of SC converter connected in parallel and an N-state hysteresis unit selection control scheme which works along the interleaving control to vary the number of converters in operation. By having the capacitors of inactive units connected to the output and the converters operating with output interleaving operation, the output capacitor that is typically required in SC converters for maintaining a small voltage ripple is made redundant in this configuration. A three-unit SC converter of the proposed configuration is described in this paper. Experimental results show that the proposed solution works satisfactorily with good regulation, input and output interleaving operations, and dynamic response for a wide operating range. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel dynamic voltage restorer (DVR) topology based on reduced-order matrix converter modules. The topology utilizes two modules for selective and independent sequence voltage synthesis. As a result, the DVR proposed herein can compensate for balanced as well as unbalanced voltage sags/swells. Each module is realized using a vector-switching matrix converter. The entire topology is energy storage free, and each module is pulsewidth modulated using simple dc duty ratios. This paper provides details on the DVR modeling, equivalent circuit, and feedback controller design. Thorough computer simulations and experimental prototyping are used to validate the approach. [ABSTRACT FROM PUBLISHER]

Single-phase power factor correction (PFC) ac–dc converters are widely used in the industry for ac–dc power conversion from single phase ac-mains to an isolated output dc voltage. Typically, for high-power applications, such converters use an ac–dc boost input converter followed by a dc–dc full-bridge converter. A new ac–dc single-stage high-power universal PFC ac input full-bridge, pulse-width modulated converter is proposed in this paper. The converter can operate with an excellent input power factor, continuous input and output currents, and a non-excessive intermediate dc bus voltage and has reduced number of semiconductor devices thus presenting a cost-effective novel solution for such applications. In this paper, the operation of the proposed converter is explained, a steady-state analysis of its operation is performed, and the results of the analysis are used to develop a procedure for its design. The operation of the proposed converter is confirmed with results obtained from an experimental prototype. [ABSTRACT FROM PUBLISHER]

Neutral-point (NP)-clamped three-level inverter, which is a widely used topology of multilevel converters, suffers from the NP voltage drift as its main technical drawback. The nearest-three-virtual-vector (\NTV^2) modulation method can control the NP voltage balance for any load over the full range of inverter output voltage. However, compared with the nearest-three-vector (NTV) modulation method, \NTV^2 increases the switching frequency. This paper combines \NTV^2 with NTV, and the two methods are used alternately in a fundamental cycle. The duty-cycle coefficients of the redundant small vectors are analyzed to explore the intervals where NTV can control the NP voltage balance in a fundamental cycle. The proportional parameter, which represents the combination of the two methods in hybrid space vector pulsewidth modulation, can be selected to achieve a high-performance NP balance control and low switching frequency. The steady- and transient-state behaviors of the proposed strategy are analyzed in this paper. The experimental results verify the validity of the proposed strategy. [ABSTRACT FROM PUBLISHER]

By establishing the mathematical model of the current stress of the isolated bidirectional dc–dc converter (IBDC), this paper comparatively analyzes the performances of IBDC under traditional single-phase-shift control and dual-phase-shift (DPS) control. On this basis, this paper proposes a current-stress-optimized switching strategy for IBDC with DPS control, and the corresponding control scheme is designed and implemented. The current-stress-optimized switching strategy can minimize the current stress, improve the system efficiency, and increase system power capability, and these performances are particularly effective for operation conditions with high voltage conversion ratio and light load. At last, experimental results verify the excellent performance of the current-stress-optimized switching strategy and correctness of the theoretical analysis. [ABSTRACT FROM PUBLISHER]

This paper presents a modulation strategy for the modular multilevel converter (MMC) which provides the voltage balancing of the capacitors of different submodules comprising the converter. Not only is this modulation applicable to MMCs constructed with classic two level (2L) submodules, but it is also effective for arrangements with different submodule concepts, for instance, topologies like neutral point clamped (NPC), flying capacitors (FCs), neutral point piloted (NPP), etc. Therefore, firstly, the general modulation philosophy is explained applied to the two level (2L) submodule concept, and secondly, the extension to 3L-NPC and 3L-FC submodule topologies is analyzed. After that, the validation of the studied modulation strategy is carried out by means of successful simulation results, at different switching frequencies and number of submodules. The corresponding experimental results are shown in Part II of this paper after having implemented the aforementioned modulation strategy in a real test bench. In addition to this, a comparison based on thermal analysis and sizing of elements among the four studied submodule topologies is also included. [ABSTRACT FROM PUBLISHER]

Modern development of semiconductor power-switching devices has promoted the use of power electronic converters as power transformers at the distribution level. This paper presents an ac–ac dual-active-bridge (DAB) converter for a solid-state transformer. The proposed converter topology consists of two active H-bridges and one high-frequency transformer. Four-quadrant switch cells are used to allow bidirectional power flow. Because power is controlled by the phase shift between two bridges, output voltage can be regulated when input voltage changes. This paper analyzes the steady-state operation and the range of zero-voltage switching. It develops a switch commutation scheme for the ac–ac DAB converters. Experimental results from a scaled-down prototype are provided to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

In recent years, high photovoltaic array voltage up to 1000 V and transformerless grid-tied inverter have been increasingly researched and applied to elevate the inverter and the dc power collection efficiency. With the same reasons, a three-level neutral point clamped (3L-NPC) inverter featuring low power device voltage stress and low leakage current becomes increasingly attractive. In this paper, the operation and the features of a novel grid-tied 3L-NPC are presented. The proposed topology is a derivative of the three-level stacked neutral point clamped (3L-SNPC) structure. However, compared with the conventional 3L-SNPC and its pulse width modulation (PWM) strategy, the new topology with novel PWM strategy features completely inactive intrinsic body diodes. Furthermore, only two outer power devices are working with switching frequency, while the other four Insulated Gate Bipolar Transistors (IGBTs) are actually with the grid frequency. Therefore, the relatively high switching frequency is selected to reduce the inverter output filter inductance. A hybrid CoolMosfet and IGBT power module configuration is also proposed based on the new PWM strategy. The calculation shows that the total power device losses are reduced. The experimental results are illustrated in this paper to confirm the operation of the proposed topology and controller. [ABSTRACT FROM PUBLISHER]

In the paper by Chen et al. (IEEE Trans. Ind. Electron., vol. 66, no. 4, pp. 2837–2846, Apr. 2019), the authors proposed two fault-tolerant control strategies for T-type three-level inverters considering neutral-point (NP) voltage oscillations. However, some basic problems are worth being discussed about the proposed fault-tolerant control methods. This letter presents some comments and results concerning the paper by Chen et al. [ABSTRACT FROM AUTHOR]

In this paper, an immune algorithm (IA) is developed for optimization of the harmonic performance of a three-phase inverter under the space-vector pulsewidth-modulation (SVPWM) control strategy. The presented algorithm employs the immune approach as the search method for finding the best optimal control vectors and action time of the three-phase inverter. As a result, the optimal control vectors and action time are calculated to minimize the objective function of the weighted total harmonic distortion of the output voltage waveforms. In addition, an experimental platform based on DSP and field-programmable gate array is built. This paper provides a detailed performance analysis of the method with comparison to the conventional SVPWM. The simulation and experimental results verify the superiority of the best control sequences generated by IA compared with the existing conventional control strategies. [ABSTRACT FROM PUBLISHER]

A new pulse width modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is developed and presented in this paper. The proposed PWM scheme not only takes advantage of the special properties available in NPC inverters, but also reduces the switching loss of the inverter along with an inherent neutral point (NP) voltage control. Based on a circuit-level decoupling concept, the NPC inverter can be decoupled into two three-level Buck converters in every defined operating section, and thereby the controller design can be simplified. The salient features of the proposed scheme, as compared with the existing carrier-based DPWM strategies, are: 1) its reduced computational processing time, 2) its capability to balance the dc-link voltage without any additional control, and 3) its reduced complexity, e.g., only one carrier wave needed for pulse width modulating. Same as a space-vector modulation, the maximum modulation index, 1.1547, can be attainable by the proposed scheme. Moreover, compared to conventional continuous sinusoidal PWM, using this technique proposed here, the switching losses of the devices can be reduced by one third. In order to explain the operation of this topology properly, the decoupling principle including the driving signal synthesis and the NP potential variation are analyzed in detail in this paper. Finally, the viability and performance of the proposed modulation scheme are shown through simulation and experimental results in a laboratory prototype. [ABSTRACT FROM PUBLISHER]

A switching power-converter closed-loop online autotuning controller is presented in this paper. The presented controller is based on tuning the closed-loop-compensator parameters by simply observing the compensated-error-signal time-domain characteristics. Moreover, the presented online autotuning controller does not require the knowledge of the power-stage frequency response, does not depend on any conventional rule-of-thumb control-design criteria such as gain and phase margins, can be used without interrupting the normal operation of the power converter, and is relatively simple when compared to other methods particularly those that require measuring the frequency response of the power stage or closed-loop converter system. The online autotuning controller is presented in this paper based on a dc–dc buck switching converter with a fully digital closed-loop controller, as an example and not for limitation. [ABSTRACT FROM PUBLISHER]

A new three-phase single-stage rectifier is proposed in this paper. The outstanding features of the proposed rectifier are that it can produce input currents that do not have deadband regions and an output current that can be continuous when the converter is operating from maximum load to at least half of the load. In this paper, the operation of the new converter is explained, its features and design are discussed in results, and its operation is confirmed with experimental results obtained from a prototype. [ABSTRACT FROM PUBLISHER]

In this paper, a new active current balancing method for a light-emitting diode (LED) driver with multichannel outputs is proposed. In the proposed structure, a low-power nonisolated dc–dc converter in series with each LED string is used to regulate the LED string current. Different from conventional active current balancing methods, in the proposed method, the nonisolated dc–dc converters only process a small portion of the total output power. Thus, the cost and size can be greatly reduced. An adaptive bus voltage control method is also proposed to minimize the output power of the nonisolated dc–dc converters. The proposed method features good modularity, expandability, and individual current control capability. Performance of the proposed method is validated by the experimental results from an 80-W prototype with four channel outputs. [ABSTRACT FROM PUBLISHER]

This paper presents a novel soft-switching galvanically isolated buck-boost dc–dc converter as a module-integrated converter for photovoltaic (PV) applications. It features three major operating modes: boost, normal, and buck mode. Their proper distribution over the input voltage range enables wide voltage regulation capabilities, i.e., close to those of nonisolated power optimizers. The proposed control algorithm requires only one buck-boost switching stage that performs voltage regulation by means of the switching stage reconfiguration with smooth transition between the modes. The design guidelines and the digital control system for PV applications are provided. The module-integrated converter was verified experimentally with a solar array simulator. The converter showed good maximum power point tracking performance and a peak efficiency of nearly 97%. [ABSTRACT FROM PUBLISHER]

In this paper, a novel discontinuous current-source driver (CSD) is proposed, in which the power MOSFET gate-source voltage is increased to more than the drive supply voltage. The proposed CSD is able to recover gate energy dissipated in a conventional driver. In comparison to the conventional gate driver, the proposed CSD achieves fast switching speed to reduce switching losses. A wide range of operating duty cycle, low circulating losses, and high Cdv/dt immunity are other features of the proposed CSD. In comparison to previous discontinuous CSDs, the special advantage of the proposed circuit is power MOSFET gate voltage boosting, which leads to reduction of Rds(on) and, thus, the conduction loss. The proposed circuit is appropriate for voltage regulators (VRs) with synchronous rectifier and also it is suitable for two-stage 48-V power pod applications and low-voltage converters. Two-stage VR for laptop computer CPUs is another application of this gate driver circuit to improve light load performance. A prototype of the circuit operating at 1 MHz is implemented, and the experimental waveforms justify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

A microconverter serves as a front-end dc–dc stage of a microinverter to convert the power from a photovoltaic module to a dc bus. These front-end microconverters require isolation, high-boost ratio, wide-input voltage regulation, and high efficiency. This paper introduces an isolated resonant converter with hybrid modes of operation to achieve wide-input regulation while still maintaining high efficiency. The proposed converter is designed as a series resonant converter with nominal-input voltage and operates under two additional modes: a boost converter with low-input voltage and a buck converter with high-input voltage. Unlike conventional resonant converters, this converter operates at discontinues conduction mode with a fixed frequency, simplifying the design and control. In addition, this converter can achieve zero-voltage switching (ZVS) and/or zero-current switching (ZCS) of the primary-side MOSFETs, ZVS and/or ZCS of the secondary-side MOSFETs, and ZCS of output diodes under all operating conditions. Experimental results using a 300-W prototype achieve a peak efficiency of 98.1% and a California Energy Commission efficiency of 97.6% including all auxiliary and control power at nominal-input voltage. [ABSTRACT FROM PUBLISHER]

This paper deals with a standalone doubly fed induction generator-direct current (DFIG-dc) system, where stator and rotor are connected to an isolated dc load, via diode rectifier and voltage-source inverter, respectively. A direct torque control scheme is proposed for dc voltage regulation, where the dc voltage is regulated by a torque controller, while stator frequency is maintained at a nearly rated frequency, by achieving constant dc voltage to rotor flux ratio. An innovative switching strategy is developed to incorporate the phase sequence change in rotor current from subsynchronous speed to supersynchronous speed. Variable switching due to a hysteresis controller provides a reduction in the harmonic content of stator current. This control is simple in implementation, and less parameter dependent. There is no requirement of exact position sensing, while the speed measurement is sufficient, which also reduces the cost and maintenance of an accurate position sensor. Sensing of stator voltage and current is not required in this scheme, and control is done with a minimum number of sensors. As the number of turns on the stator is higher than the rotor, to have common dc link and to exploit rated stator MMF, roles of stator and rotor are interchanged. Performance of the control scheme is verified experimentally on a 4 kW DFIG, and results are reported. [ABSTRACT FROM AUTHOR]

This paper presents a new active capacitor voltage balancing control method for the flying capacitor multicell (FCM) converters which is fully implemented using logic-form equations. The proposed active capacitor voltage balancing control technique, measures output current and flying capacitor (FC) voltages to generate the switching states in order to produce the required output voltage level and to balance FCs’ voltages at their reference values. Output voltage of the FCM converter controlled with proposed active capacitor voltage balancing method can be modulated with any pulse width modulation (PWM) technique such as the phase-shifted-carrier PWM or level-shifted-carrier PWM. An advantage of the proposed active capacitor voltage balancing control method is its simplicity as it does not require any complex computations and tedious optimization calculations. Simulation results and experimental measurements of a three-cell four-level and four-cell five-level FCM converters are presented to verify the performance of the proposed active capacitor voltage balancing control technique. [ABSTRACT FROM AUTHOR]

This paper proposes a novel active capacitor voltage balancing technique for stacked multicell (SM) converters. The proposed active capacitor voltage balancing control method detects the direction of the load current and measures the voltage of flying capacitors (FCs) to generate a proper switching state in order to form the required output voltage level and regulate the FC voltages at their desired reference levels. The proposed active capacitor voltage balancing control technique can modulate the output voltage through any of the pulse-width-modulation (PWM) techniques such as the phase-shifted carrier PWM or the level-shifted-carrier PWM. The foremost advantage of the proposed active control technique is that it does not demand any complex computations because it is not based on the optimization of the FC voltage-deviation cost functions. A thorough set of simulation results and experimental measurements for the five-level and seven-level SM converters are provided to validate the proposed active capacitor voltage balancing control method. [ABSTRACT FROM AUTHOR]

This paper presents a new buck converter with optimum-damping and dynamic-slope compensation techniques. The optimum-damping control is a well-known current control method, and the proposed dynamic-slope generator can achieve frequency compensation to prevent subharmonic oscillation. When the system is disturbed, the proposed dynamic-slope generator can stabilize the circuit in a single cycle. Hence, the dynamic-slope compensation can be used to replace traditional extra slope compensation in the optimum-damping-control circuit. The measured transient time of the load current is 2 μs from 50 to 500 mA, and 3 μs from 500 to 50 mA. The optimum-damping-control techniques can rapidly reach desired output voltage in 2–3 switching cycles. The experimental and simulation results confirm that the proposed approach can achieve the slope compensation and accelerate the transient response. The proposed converter has been fabricated with TSMC 0.18 μm CMOS 1P6M technology. The converter's operating frequency is 1 MHz, the maximum output current is 500 mA, and the peak power efficiency is 89.68% under 300-mA load current. The chip area is only 1.0376 mm × 1.0599 mm (include PADs). [ABSTRACT FROM PUBLISHER]

This paper proposes a generalized hybrid modulation strategy to extend the operation of asymmetrical cascaded multilevel converters into the overmodulation region during fault conditions on the power cells. The proposed strategy makes use of the advantages of both space vector and carrier-based geometrical modulations to allow the converter to operate with a wide range of modulation indexes and fault conditions. Also, it does not need to precalculate various trajectories for the voltage reference, which would be a very complex task, as the shape of the converter space vector diagram is different for each type of fault condition. It is shown that different kinds of overmodulation can happen during faults on the power cells, and solutions are presented for each mode of operation. Finally, simulation and experimental results are shown to demonstrate the good performance of the proposed modulation strategy. [ABSTRACT FROM PUBLISHER]

This paper proposes a unique carrier-based pulse width modulation strategy for a three-level neutral-point-clamped inverter that works satisfactorily and with uniform convergence time over the full power factor (PF) range of the load variation. It has excellent control over capacitor voltages and mitigates low-frequency oscillations in the neutral point for the full PF range. First, an investigation is made to see how the load currents get modulated to generate compensating neutral current causing charging and discharging of dc-link capacitors. It is observed that when an additional modulating voltage signal that is in phase with the corresponding phase current is added in each phase, a neutral current is produced in the right direction which can be used to compensate for any prior unbalance in capacitor voltages. It is demonstrated that the performance of this scheme is insensitive to the load PF variation (full range from zero to unity). It performs satisfactorily throughout the entire linear modulation range and eliminates any undesirable low-frequency harmonic component in the compensating neutral current. The effectiveness of the proposed scheme is verified through simulation and experimental results by varying load PF as well as modulation index with both passive and motor loads. [ABSTRACT FROM PUBLISHER]

The high number of power semiconductors in multilevel converters makes them susceptible to failure. Therefore, one of the main concerns in utilizing multilevel inverters is their reliability. This paper proposes a new simple fault-diagnosis and fault-handling method to increase the robustness and reliability of a flying capacitor multilevel inverter (FCMLI) which is one of the most prominent multilevel inverters. The proposed method is capable of diagnosing failed switch(es) and reconfiguring the switching sequence such that the output voltage is maintained similar to a normal operation condition. The proposed scheme identifies failed switch(es) by using the information about the charging state of the capacitors and the applied switching sequence. After identifying the failed switch(es), the algorithm bypasses the failed switch(es) and converts the control signals of the faulty leg from an M -cell L-level configuration to an (M-F)-cell L -level configuration (where F is the number of failed switches). The most attractive feature of the proposed control scheme is that any number of failed switches can be tolerated, as long as the number of functional switches is higher than the minimum number of cells required to build a full-binary L-level FCMLI. Simulation and experimental results are presented that verify the effectiveness of the proposed method. [ABSTRACT FROM PUBLISHER]

In this paper, the near-state pulse width modulation (NSPWM), adapted to be used in dual-voltage source inverter (VSI) fed open-end load, is introduced primarily aiming to appreciably minimize the voltage total harmonic distortion (THD). Within the framework of the proposed method, the active time of pulses at the second inverter is relatively adjusted within switching interval (compared to the first VSI). The phase voltage harmonics are formulated for dual-inverter modulated by NSPWM; then, optimal adjustment is identified via a three-dimensional curve of phase voltage THD versus modulation index (MI) and phase angle displacement (PAD). Due to the limitation of MI in NSPWM, the desired output voltage is synthesized with modifying not only MI but also PAD between references of two VSIs. Furthermore, NSPWM inherently takes advantage of better efficiency compared to conventional space vector modulation due to switching only two phases within an interval (by clamping one phase to positive/negative dc-rail). The dual-VSI supplied by two isolated dc sources is assembled in the laboratory to experimentally evaluate the THD reduction feature of the proposed method; also, the simulation results obtained by means of a MATLAB/Simulink environment show close agreement with experimental data. [ABSTRACT FROM PUBLISHER]

This paper focuses on the implementation of an extended model predictive-sliding mode control (EMP-SMC) for three-phase grid-connected converters (GcCs). The proposed control considers the GcC model in the dq synchronous reference frame to forecast possible future behavior of the grid current. After that, the applied voltage vector is selected so that a predefined cost function is minimized. This function is aimed to reduce the grid current ripples during steady-state operation. Compared to the conventional MPC, the proposed EMP-SMC algorithm uses 19 voltage vectors (7 real voltage vectors and 12 additional virtual voltage vectors) for the prediction process. Accordingly, lower grid current THD and lower switching losses are obtained. However, the increase of voltage vectors number will lead to higher computation time delay that may affect the control performances. To overcome this problem, the proposed control uses a sliding mode-based preselection step that limits the prediction process to only ten voltage vectors at the most and a table-based implementation process that reduces significantly the execution time of the whole control algorithm. Simulation and experimental results are presented in order to show performances and effectiveness of the proposed EMP-SMC algorithm. [ABSTRACT FROM AUTHOR]

This paper presents a new multicell topology based on flying capacitor (FC) structure suitable for multilevel converters. The proposed topology employs the concept of phase-shifted carrier pulse width modulation (PWM) with modified modulating signals to generate appropriate PWM signals. The modulation strategy along with all possible switching states are explained. The implementation of the proposed PWM technique is shown by the help of illustrating waveforms. To show the advantages of the proposed structure, different performance criteria are compared with other FC multicell (FCM) structures. Simulation results are used to further evaluate the potential merits of the proposed topology. It is shown that the proposed structure is superior to other FCM-based structures from different standpoints. Specifically, it reduces the number of high-frequency switches, the number of FCs, and at the same time improves the quality of output voltage. A laboratory-type experimental setup is used to validate the modulation strategy and other theoretical findings. [ABSTRACT FROM AUTHOR]

This paper presents a sampled-time-domain analysis to investigate the sampling effect on instantaneous switching frequency of a digitally implemented hysteresis current control (HCC) in a voltage source inverter (VSI). The generalized expression of the instantaneous switching frequency with the consideration of sampling frequency has been derived. The effect of variation in sampling frequency on effective hysteresis band and switching frequency has been analyzed. The difference between maximum to minimum switching frequency of a fixed-band HCC VSI depends on the sampling frequency of the digital controller. The sampling also generates a steady-state tracking error exceeding the fixed-band limit at the fundamental frequency for fixed hysteresis band operation. The analysis has been done to achieve fixed switching frequency with variable hysteresis band and with varying sampling period. The frequency spectrum of the load current is presented to show the effect of a digital controller. The sampling effect on the switching performance has been demonstrated for a single-phase VSI under different loading conditions. To verify the analytical results, the simulation and experimental results are obtained with the current controller implemented on a field programmable gate array-based digital controller. [ABSTRACT FROM PUBLISHER]