Search

In this paper, a nonisolated dc–dc converter with high voltage gain is presented. Three diodes, three capacitors, an inductor, and a coupled inductor are employed in the presented converter. Since the inductor is connected to the input, the low input current ripple is achieved, which is important for tracking maximum power point of photovoltaic panels. The voltage stress across switch S is clamped by diode D 1 and capacitor C1. Therefore, a main switch with low on-resistance RDS (on) can be employed to reduce the conduction loss. Besides, the main switch is turned on under zero current. This reduces the switching loss. The steady-state analysis of the proposed converter is discussed in this paper. Finally, the proposed converter prototype circuit is implemented to justify the validity of the analysis. [ABSTRACT FROM PUBLISHER]

In this paper, a nonisolated bidirectional dc–dc converter is presented. The proposed converter consists of two boost converters to enhance the voltage gain. Four power switches with their body diodes are employed in the proposed converter. Also, two inductors and a capacitor are used as passive components. The input current is divided to the inductors which causes the efficiency to be high. The voltage gain of the proposed converter is higher than the conventional cascaded bidirectional buck/boost converter (CCBC) in step-up mode. Besides, the voltage gain in step-down mode is lower than CCBC. Besides, the efficiency of the proposed converter more than CCBC while the total stress on active switches are same. The simple structure of the proposed converter causes its control to be easy. The steady-state analysis of the proposed converter is discussed in this paper thoroughly. The stress on converters’ devices and the efficiency of the proposed converter and CCBC are compared in this paper. Finally, the proposed converter prototype circuit is implemented to justify the validity of the analysis. [ABSTRACT FROM PUBLISHER]

A nonisolated bidirectional dc–dc converter with high voltage gain, low voltage stress, low component count, and soft-switching features is presented in this paper. In this topology, coupled inductors and voltage multiplier cells are merged to achieve high step-up/down voltage gain. Also, due to using active clamp circuits, the voltage stress of power switches is relatively low. Thus, the low voltage switches with low on-resistance can be employed to reduce the conduction losses. Furthermore, zero-voltage switching is accomplished in both high step-up and high step-down modes for all power switches, and due to zero-current switching operation of all antiparallel diodes, the reverse recovery losses are reduced. In order to verify the theoretical analysis and the converter performance, a 200 W prototype circuit of the proposed converter is implemented in the laboratory. [ABSTRACT FROM AUTHOR]

High step-up converters are required for distributed photovoltaic generation systems, due to the low voltage of the photovoltaic source. In this paper, a new hybrid high voltage gain dc–dc converter is created by merging the standard boost converter with a coupled inductor and different switched-capacitor techniques. With a single switch and no requirement of higher duty cycle values, the proposed converter achieves a high voltage gain and high efficiency, in addition to lowered voltage and current stresses of the components. A 200-W prototype was implemented experimentally to evaluate the converter, which reached a maximum efficiency of 97.6%. [ABSTRACT FROM AUTHOR]

In this paper, a hybrid switched-capacitor/switched-quasi-Z-source bidirectional dc–dc converter is proposed for electric vehicles (EVs) with hybrid energy sources, which has a wide voltage gain range in the bidirectional energy flows. Compared with the traditional quasi-Z-source bidirectional dc–dc converter, the proposed converter only changes the position of the main power switch and employs a switched-capacitor cell at the output of the high-voltage side. Therefore, the advantages of the wide voltage gain range and the lower voltage stresses across the power switches can be achieved. The operating principle, the voltage and current stresses across the power switches, and the comparisons with other converters are analyzed in detail. Furthermore, the parameter design of the main components, the dynamic modeling analysis, and the voltage control scheme are also presented. Finally, the experimental results obtained from a 400 W prototype validate the characteristics and the theoretical analysis of the proposed converter. [ABSTRACT FROM AUTHOR]

Single-stage power-factor-corrected (S2PFC) power supplies usually suffer from high voltage stress, due to lack of control on the intermediate bus capacitor voltage. In the past, analysis of such voltage stress was mostly based on steady-state condition without providing sufficient explanation during the transient circuit operation. This paper revisits the problem at circuit level and reports that the root cause is due to the inherent negative current feedback property of the output inductor or the transformer operating in continuous conduction mode (CCM). Based on the finding, this paper further proposes a new approach to reducing the voltage stress by adding an auxiliary circuit branch to existing S2PFC converters. The additional circuit branch limits the effect of negative current feedback by suppressing the change of output current slope due to change of load. This assists the pulsewidth modulation controller to track the change of load better such that the bus capacitor voltage range is reduced through duty cycle control. The auxiliary circuit branch also reduces reverse-recovery-related losses of the converter under CCM operation. A laboratory prototype using the popular boost PFC converter combined flyback dc/dc converter was built and tested to confirm the analysis and effectiveness of the approach. [ABSTRACT FROM AUTHOR]

High-gain voltage conversion is a feature required for several applications, especially for power processing of low-voltage renewable sources in grid-connected systems. In this scope, the presented paper proposes a novel transformerless high gain step-up dc–dc converter based on an active switched-inductor and a passive switched-capacitor networks. The main advantages of the proposed converter are the high voltage gain (>10), the reduced voltage stresses across the switches and the reduced number of components when compared to topologies that provide the same voltage gain using similar principles. The detailed analysis of the proposed converter and a comparison considering other topologies previously published in the literature are also presented in this manuscript. In order to verify the proposed converter performance, a prototype has been built for a power of 200 W, input and output voltages of 20 and 260 V, respectively, and switching frequency of 50 kHz. Experimental results validate the effectiveness of the theoretical analysis proving the satisfactory converter performance, which peak efficiency is around 95.5%. [ABSTRACT FROM PUBLISHER]

A common ground switched-quasi-Z-source bidirectional dc–dc converter is proposed for electric vehicles with hybrid energy sources. The proposed converter is based on the traditional two-level quasi- Z-source bidirectional dc–dc converter, changing the position of the main power switch. It has the advantages of a wide-voltage-gain range, a lower voltage stress across the power switches, and an absolute common ground. The operating principle, the voltage and current stresses on the power switches, the comparisons with the other converters, the small signal analysis, and the controller design are presented in this paper. Finally, a 300 W prototype with $U_{{\rm{high}}}= {240 \ \rm{V}}$ and $U_{{\rm{low}}}= {40\sim 120\ \rm{V}}$ is developed, and the experimental results validate the performance and the feasibility of the proposed converter. [ABSTRACT FROM PUBLISHER]

This paper proposes a soft switching nonisolated dc/dc interleaved converter incorporating coupled inductors and switched capacitors for high step-up applications. The converter integrates the interleaved structure and winding-cross-coupled inductors technique to reduce current stress of semiconductor devices and diminish the input current ripple considerably. In addition, the interleaved converter has the automatic current sharing characteristic. The applied zero voltage transition cell provides soft switching in a wide range of load variations with a minimum number of elements. In this topology, all semiconductor devices are soft switched, having eliminated switching losses and alleviating the reverse recovery problem of the output diodes. In addition, the voltage stress across the switches is very low. The theoretical analysis and design procedure of the introduced topology are presented. Also, the proposed converter is compared to the latest similar soft switched high step-up converters. The accuracy of the theoretical analysis is validated by a 200-W prototype operating at 100 kHz. [ABSTRACT FROM PUBLISHER]

The asymmetrical modulation strategy is widely used in various types of three-level (TL) dc/dc converters, while the current imbalance among the power switches is one of the important issues. In this paper, a novel periodically swapping modulation (PSM) strategy is proposed for balancing the power switches’ currents in various types of TL dc/dc converters. In the proposed PSM strategy, the driving signals of the switch pairs are swapped periodically, which guarantees that the currents through the power switches are kept balanced in every two switching periods. Therefore, the proposed PSM strategy can effectively improve the reliability of the converter by balancing the power losses and thermal stresses among the power switches. The operation principle and performances of the proposed PSM strategy are analyzed in detail. Finally, the simulation and experimental results are presented to verify the proposed modulation strategy. [ABSTRACT FROM PUBLISHER]

In this paper, a common grounded Z-source dc–dc converter with high voltage gain is proposed for photovoltaic (PV) applications, which require a relatively high output–input voltage conversion ratio. Compared with the traditional Z-source dc–dc converter, the proposed converter, which employs a conventional Z-source network, can obtain higher voltage gain and provide the common ground for the input and output without any additional components, which results in low cost and small size. Moreover, the proposed converter features low voltage stresses of the switch and diodes. Therefore, the efficiency and reliability of the proposed converter can be improved. The operating principle, parameters design, and comparison with other converters are analyzed. Simulation and experimental results are given to verify the aforementioned characteristics and theoretical analysis of the proposed converter. [ABSTRACT FROM PUBLISHER]

This paper presents high step-up dc-to-dc converter for low voltage sources such as solar photovoltaics, fuel cells, and battery banks. To achieve high voltage gain without large duty cycle operation, combination of coupled inductor and switched capacitor voltage doubler cells are used. By incorporating active clamp circuit, voltage spike due to the leakage inductance of the coupled inductor is alleviated and zero-voltage switching turn on of the main and auxiliary switch is obtained. Due to the use of MOSFETs of low voltage rating and soft turn on of the switches, conduction loss and switching losses are reduced. This improves the efficiency and power density of the converter. The proposed converter can achieve high voltage gain with reduced voltage stress on MOSFET switches and output diodes. Design and analysis of the proposed converter is carried out, and finally, a 500-W experimental prototype is built to verify theoretical analysis. [ABSTRACT FROM PUBLISHER]

This paper presents a dc–dc boost converter with high voltage gain based on the three-state switching cell for split-capacitor neutral-point-clamped inverters. The proposed converter is analyzed considering the operation in continuous conduction mode and duty cycle higher than 0.5, which corresponds to overlapping mode. The main characteristics of the topology are operation at high switching frequency, whereas the input inductor is designed for twice such frequency; in order to minimize weight and volume, the voltage stress across the switches is lower than half of the output voltage and naturally clamped by one output capacitor, allowing the use of MOSFET transistors with reduced intrinsic on-resistance; the input current presents small ripple; the output voltage can be further stepped up by increasing the transformer turns ratio without compromising the voltage stress across the switches; and the output voltage is naturally balanced, thus making the converter suitable for supplying split-capacitor inverters. Several topologies where a high voltage step-up is possible are initially investigated in the literature. Then, the principle of operation and experimental results for a 1-kW prototype are presented to validate the theoretical analysis and demonstrate the converter performance. [ABSTRACT FROM PUBLISHER]

This paper proposes a zero-voltage switching (ZVS) pulsewidth modulation (PWM) dc/dc converter with current double rectifiers to achieve ZVS for all switches under a wide range of load conditions and input voltages. Two three-level PWM circuits sharing the same power switches are adopted in the proposed converter to reduce the voltage stress of each MOSFET at Vin/2 and achieve load current sharing. Thus, the current stress and power rating at the secondary-side components are reduced. The current double rectifiers are used at the secondary side to partially cancel the output ripple current. Thus, the sizes of the magnetic components and output filter capacitance are reduced. Due to the resonant behavior by the resonant inductance and resonant capacitance at the transition interval, all switches are turned on at ZVS. The experimental results based on a 1-kW prototype are provided to verify the operation principle of the proposed converter. [ABSTRACT FROM PUBLISHER]

This paper presents a new soft-switching dc/dc converter for high-input-voltage applications. Two half-bridge converters connected in series with interleaved asymmetric pulsewidth modulation (PWM) are adopted to limit the voltage stress of each power switch at one-half of the input dc bus voltage. In each half-bridge converter, two asymmetrical dc/dc circuits with the same active switches are connected in parallel at the output side to share the load current and reduce the current stresses of the secondary windings and rectifier diodes. Since two half-bridge converters are operated with interleaved PWM, the output ripple currents partially cancel each other so that the resultant ripple current at the output side is reduced. Active switches in the proposed circuit can be turned on at zero-voltage switching during the transition interval due to the resonant behavior by the output capacitance of MOSFETs and the leakage inductance of transformers. Experiments based on a laboratory prototype with 960-W rated power are provided to demonstrate the performance of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, a novel high step-up dc–dc converter for distributed generation systems is proposed. The concept is to utilize two capacitors and one coupled inductor. The two capacitors are charged in parallel during the switch-off period and are discharged in series during the switch-on period by the energy stored in the coupled inductor to achieve a high step-up voltage gain. In addition, the leakage-inductor energy of the coupled inductor is recycled with a passive clamp circuit. Thus, the voltage stress on the main switch is reduced. The switch with low resistance RDS(ON) can be adopted to reduce the conduction loss. In addition, the reverse-recovery problem of the diodes is alleviated, and thus, the efficiency can be further improved. The operating principle and steady-state analyses are discussed in detail. Finally, a prototype circuit with 24-V input voltage, 400-V output voltage, and 200-W output power is implemented in the laboratory to verify the performance of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, a novel high step-up dc–dc converter with coupled-inductor and voltage-doubler circuits is proposed. The converter achieves high step-up voltage gain with appropriate duty ratio and low voltage stress on the power switches. Also, the energy stored in the leakage inductor of the coupled inductor can be recycled to the output. The operating principles and the steady-state analyses of the proposed converter are discussed in detail. Finally, a prototype circuit of the proposed converter is implemented in the laboratory to verify the performance of the proposed converter. [ABSTRACT FROM AUTHOR]