Search

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

This paper proposes a wide-range zero-voltage-switching (ZVS) active-clamped current-fed push–pull converter for fuel cell application. The presented converter achieves ZVS for all of the primary switches and ZCS for secondary diodes from rated load to 10% full load over the wide input voltage variation, improving the overall efficiency. The ZVS of switches is realized by the energy stored in the transformer leakage inductance aided by the secondary parallel inductor. An additional active clamping circuit suppresses the voltage spike as well as assists in realizing ZVS of switches. Low-voltage-rated switches with low on-state resistance can be used. Moreover, the voltage-doubler rectifier is adopted to release the reverse-recovery problem of rectifier diodes and reduce turns ratio of the high-frequency transformer. Detailed steady-state operation, analysis, design, control, comparative study, and experimental results are discussed in depth in this paper. Finally, a 200-W prototype has been built in the laboratory to verify the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]

This paper proposes two coupled-inductors-based Z-source networks, called the modified series and tapped switched-coupled-inductors quasi-Z-source networks (mSSCL-qZSN and mTSCL-qZSN, respectively). These networks offer high voltage gains with less-than-unity winding turn ratios $(n < {\text{1)}}$ , resulting in a reduced inductive element size. Other advantages include a less number of active components and their lower ratings and a higher efficiency. In addition, a lower magnetic core size is required for the proposed ZSNs due to the lower peak magnetizing current. The performance principles and detailed comparative analysis are provided and confirmed through experiments on a 200-W dc–dc converter. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high step-up dc–dc converter is proposed. Active–passive inductor cells (APICs) are used to extend the topology. The ability to achieve high gains is the main merit of the proposed topology. The proposed converter operates based on parallel charging and series discharging of the inductors. The converter also achieves high step-up voltage gain with appropriate duty cycle and low voltage and current stress on the power switches and diodes. The proposed converter is analyzed in operation modes. The main parameters of the converter such as voltage gain, voltage stress of semiconductor devices are calculated to compare with other structures. Considering the output voltage ripple and filter size, the proposed converter is designed. Moreover, the losses and efficiency of the converter are calculated. The performance of the proposed converter is validated by experimental results. [ABSTRACT FROM AUTHOR]

Peak current mode (PCM) control has been widely used for the control of switching dc–dc converters due to its excellent transient performance. With the development of single-inductor dual-output (SIDO) dc–dc converters, PCM control technique is introduced to the control of SIDO dc–dc converters. Conventional PCM buck converter has only one reference current, with two inductor current borderlines are used to divide the operation modes of inductor current. However, PCM SIDO buck converter has more inductor current borderlines as it has one more reference current than that of PCM buck converter. In this paper, inductor current borderlines of PCM SIDO buck converter are investigated, and unified discrete iterative model of PCM SIDO buck converter is established. The effect of the difference of reference currents, initial inductor current and input voltage on the stability of PCM SIDO buck converter has been discussed by using bifurcation diagrams. The study results show that the stability of PCM SIDO buck converter is sensitive to the difference of reference currents, initial inductor current and input voltage. The stability boundary of the difference of reference currents, stability region of initial inductor current, and stability boundary of input voltage are derived. Lyapunov exponent and experimental results are carried out to verify the theoretical analysis results. [ABSTRACT FROM PUBLISHER]

This paper extends the trans-Z-source concept to ac–ac power conversion and proposes a novel single-phase trans-Z-source ac–ac converter. The proposed converter retains the advantages of its existing Z-source/quasi-Z-source counterparts in which the output voltage can be boosted and in-phase with the input voltage or bucked/boosted and out-of-phase with the input voltage. Meanwhile, a coupled inductor is introduced into the proposed converter, and the turns ratio of the coupled inductor become another control variable beside the duty cycle to obtain extreme voltage gain. Importantly, the input voltage and output voltage share the same ground, and the input current could be continuous, which is a benefit for reducing input current harmonics. Most important of all, the safe-commutation strategy for the proposed converter is deep developed, and analytic expression between the switches state and loop circuit voltage/current condition is derived out. Hence, the current/voltage ripple can be avoided without a loss snubber circuit, which benefits a reduced cost and enhanced reliability. The performance analysis is discussed in consideration of parasitic resistance, and system parameter design is optimized based on theoretic calculation. A laboratory prototype is fabricated, and experiments are performed to verify the validation of the proposed converter. [ABSTRACT FROM PUBLISHER]

This paper proposes an isolated single-ended primary-inductor converter (SEPIC) dc–dc converter with ripple-free input current and lossless snubber. The proposed converter is based on a conventional isolated SEPIC converter to enable electrical isolation and high voltage gain using a coupled inductor. The input current ripple is significantly reduced by utilizing an auxiliary circuit that also functions as a lossless snubber circuit with an additional diode. Moreover, the maximum switch voltage stress is clamped to a low voltage by the snubber circuit. Therefore, a low voltage rating mosfet that has low $R_{{\rm{DS(on)}}}$ can be utilized as a main switch device. Hence, the total power efficiency is improved. Experimental results from a 100 W prototype, which are presented to verify the theoretic analysis and performance of the proposed converter. [ABSTRACT FROM PUBLISHER]

A novel transformerless buck–boost dc–dc converter is proposed in this paper. The presented converter voltage gain is higher than that of the conventional boost, buck–boost, CUK, SEPIC, and ZETA converters, and high voltage can be obtained with a suitable duty cycle. In this converter, only one power switch is utilized. The voltage stress across the power switch is low. Hence, the low on-state resistance of the power switch can be selected to decrease conduction loss of the switch and improve efficiency. The presented converter has simple structure, therefore, the control of the proposed converter will be easy. The principle of operation and the mathematical analyses of the proposed converter are explained. The validity of the presented converter is verified by the experimental results. [ABSTRACT FROM PUBLISHER]

A new single-phase \uppi-\texttype 5-level inverter using 3-terminal switch-network (3TSN) is proposed in this paper. The topology is considered as a variant of T-type 3-level structure or dual-buck inverter with coupled inductors. This new inverter is suitable for multilevel power inversion with low dc-bus voltage. The merit of the proposed topology is to apply only four active power switches to achieve 5-level operation. Other benefits include double frequency operation of output inductor and equal division of the current that flows through power switches and filter inductor. Hence, it leads to high efficiency and low harmonics. These characteristics allow improvement of losses distribution and volume reduction of output filter inductor. The operation scenario with sinusoidal pulsewidth modulation (SPWM) is described in details. Meanwhile, the magnetic analysis and design are studied and discussed. Finally, a prototype is built to verify the theoretical analysis and demonstrate the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

In this paper, a new topology for half-bridge switched boost inverter (HB-SBI) is proposed. The proposed half-bridge inverter uses more active elements rather than capacitors and inductors in comparison with the conventional half-bridge Z-source inverter with two Z-networks, which results in reduction of weight, size, and cost. Moreover, the proposed inverter has the capability of eliminating inverter leg short-circuit issues and is able to further increase the output voltage level in comparison with its conventional types. Generating zero-level output voltage is also another advantage of this topology. Based on theoretical calculations, the steady-state and small-signal analysis of the proposed topology in different operating modes are performed and the ripple of inductors’ current and capacitors’ voltage are also calculated. A comprehensive comparison is also made between the proposed inverter and the conventional types. Finally, the experimental results are provided to reconfirm the performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

In this paper, a family of three-phase direct pulse-width modulated (PWM) ac–ac converters consisting of buck, boost, and buck–boost converters is proposed. The proposed converters have no commutation problem even if all of the switches are turned on or off simultaneously. They do not use lossy snubbers and do not sense the voltage polarity for commutation, and produce high-quality output voltage waveforms. The proposed converters allow the use of power MOSFETs and fast recovery freewheeling diodes independently. The use of power MOSFETs as active switches and freewheeling diodes with extremely fast recovery features lower the switching losses and enable us to reduce the volume of passive components by increasing switching frequency. The input (or output) filter inductor experiences twice of the converter switching frequency and thus can be designed with minimum size. To increase power density of the proposed converters, a three-phase three-limb coupled inductor is proposed. Three-phase coupled inductor integrates three separate coupled inductors of the proposed converters in one three-limb core. In comparison with separate coupled inductors, the three-phase coupled inductor has a smaller size with large current-handling capability. Experimental results obtained for the boost-type converter show the robustness of the proposed three-phase ac–ac converters. [ABSTRACT FROM AUTHOR]

This paper presents a dc–dc boost converter with high voltage gain based on the three-state switching cell for split-capacitor neutral-point-clamped inverters. The proposed converter is analyzed considering the operation in continuous conduction mode and duty cycle higher than 0.5, which corresponds to overlapping mode. The main characteristics of the topology are operation at high switching frequency, whereas the input inductor is designed for twice such frequency; in order to minimize weight and volume, the voltage stress across the switches is lower than half of the output voltage and naturally clamped by one output capacitor, allowing the use of MOSFET transistors with reduced intrinsic on-resistance; the input current presents small ripple; the output voltage can be further stepped up by increasing the transformer turns ratio without compromising the voltage stress across the switches; and the output voltage is naturally balanced, thus making the converter suitable for supplying split-capacitor inverters. Several topologies where a high voltage step-up is possible are initially investigated in the literature. Then, the principle of operation and experimental results for a 1-kW prototype are presented to validate the theoretical analysis and demonstrate the converter performance. [ABSTRACT FROM PUBLISHER]

In this paper, a high-conversion-ratio bidirectional dc–dc converter with coupled inductor is proposed. In the boost mode, two capacitors are parallel charged and series discharged by the coupled inductor. Thus, high step-up voltage gain can be achieved with an appropriate duty ratio. The voltage stress on the main switch is reduced by a passive clamp circuit. Therefore, the low resistance R{DS(ON)} of the main switch can be adopted to reduce conduction loss. In the buck mode, two capacitors are series charged and parallel discharged by the coupled inductor. The bidirectional converter can have high step-down gain. Aside from that, all of the switches achieve zero voltage-switching turn-on, and the switching loss can be improved. Due to two active clamp circuits, the energy of the leakage inductor of the coupled inductor is recycled. The efficiency can be further improved. The operating principle and the steady-state analyses of the voltage gain are discussed. Finally, a 24-V-input-voltage, 400-V-output-voltage, and 200-W-output-power prototype circuit is implemented in the laboratory to verify the performance. [ABSTRACT FROM PUBLISHER]

The pulse-train (PT) control technique for switching dc–dc converters is simple to design and benefits from excellent control performance. Up to now, almost all of the works on PT control are focused on switching dc–dc converters operating in discontinuous conduction mode, with few works reported on PT control of switching dc–dc converters operating in continuous conduction mode (CCM). In this paper, a PT-controlled CCM buck converter is studied and a unique low-frequency oscillation phenomenon is revealed, which results in large undesired inductor-current and output-voltage variations. The effect of equivalent series resistance (ESR) output-capacitor on the low-frequency oscillation is examined. The results indicate that such oscillation occurs when the ESR output-capacitor is relatively small and disappears when it is relatively large. However, a larger ESR will result in a large output-voltage ripple. In order to avoid the low-frequency oscillation and, at the same time, to ensure a small output-voltage ripple, the ICRIF circuit is applied. In this way, a small ESR output-capacitor can be used to decrease the output-voltage ripple. Simulation and experimental results are provided to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

In this paper, a novel Zeta-mode three-level ac direct converter is proposed. The converter realizes three-level voltage waveforms before the output filter, which can get a better harmonic spectrum and reduce the bulk of the filter. Compared with two-level ac choppers, voltage stresses of the converter can be lowered. Compared with ac–dc–ac converters with no isolation and low- or middle-frequency isolation, the converter has single power stage and bidirectional power flow. Moreover, compared with buck-mode three-level ac choppers, it can realize buck and boost output voltage. The converter has four operation states in one period of input voltage and three different operation modes in one switching period. To ensure that the converter operates reliably, the noncomplementary control strategy is presented, which can make the converter switch smoothly between different modes in bidirectional power flow. Therefore, the converter is suitable to different kinds of loads. Principle analysis and experiment results of the prototype well verify the advantages of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, a new family of zero-voltage-transition bidirectional converters using coupled inductors is introduced. By applying two auxiliary switches and coupled inductors, soft-switching condition is achieved for all semiconductor elements regardless of the power flow direction. Moreover, the presence of coupled inductors provides significant reduction in the converter volume, since all the converter inductors are implemented on a single core. Also, all semiconductor elements benefit from soft-switching condition in full duty cycle range, and thus, high efficiency is achieved for full line voltage range. No extra voltage and current stresses on the main switches and the ease of control are the other properties of the proposed converters. The proposed bidirectional buck and boost converter is fully analyzed for both buck and boost operating modes. The validity of the theoretical analysis is justified using the experimental results of a 240-W 50–100-V prototype converter. [ABSTRACT FROM PUBLISHER]

In this paper, a novel high step-up dc–dc converter with coupled-inductor and voltage-doubler circuits is proposed. The converter achieves high step-up voltage gain with appropriate duty ratio and low voltage stress on the power switches. Also, the energy stored in the leakage inductor of the coupled inductor can be recycled to the output. The operating principles and the steady-state analyses of the proposed converter are discussed in detail. Finally, a prototype circuit of the proposed converter is implemented in the laboratory to verify the performance of the proposed converter. [ABSTRACT FROM AUTHOR]

A novel pseudo-continuous conduction mode (PCCM) boost power-factor-correction (PFC) converter and its corresponding control strategy are proposed in this paper. Connecting a power switch in parallel with the inductor makes the boost converter operate in PCCM, which provides an additional degree of control freedom to realize PFC control. Therefore, a simple and fast voltage control loop of the PCCM boost PFC converter can be designed to realize output-voltage regulation. The additional degree of control freedom introduced by inductor current freewheeling operation of the PCCM boost PFC converter has been exploited through the dead-zone control technique, which can be dynamically adjusted in accordance with the output-voltage ripple. Compared with continuous conduction mode (CCM) boost PFC converter, the controller of the proposed PCCM boost PFC converter is much simpler. Moreover, the PCCM boost PFC converter benefits with reduced inductor-current ripple and improved power factor compared with boost PFC converter operating in discontinuous conduction mode (DCM). Analysis, simulation, and a 400-W prototype of the PCCM boost PFC converter have been presented and compared with those of boost PFC converters operating in conventional CCM and DCM. The results show that the dynamic response of the PCCM boost PFC converter is significantly faster than the existing boost PFC converter. [ABSTRACT FROM AUTHOR]

This paper proposes an energy regeneration circuit for three-phase voltage-fed inverters using a modified Undeland snubber. The proposed system uses a quasi-square-wave zero voltage switching dc–dc auxiliary converter to regenerate the energy from snubber capacitor to the dc bus. The regenerative circuit uses a single active switch, and it operates independently of the three-phase inverter. Operation stages, theoretical waveforms, and a design methodology are presented. Experimental results based on a 4.5-kVA three-phase inverter prototype are included to validate the proposed topology. [ABSTRACT FROM PUBLISHER]

A simple current-sharing control technique for the switching power supply is presented herein, which is based on the concept of the differential-mode transformer and which makes the load current evenly shared well among phases all over the line voltage and load current ranges. This current-sharing structure is very simple, and it makes the efficiency relatively high at light load, which is quite suitable for industrial applications with standby power considered. In this circuit, a synchronously rectified switch is used to further upgrade the efficiency, and the coupling output inductors in copolarity are utilized to decrease the phase current ripples. In this paper, the detailed basic operating principles, together with mathematical deductions, are first described, and second, some simulated and experimental results are provided to demonstrate the proposed control strategy. [ABSTRACT FROM AUTHOR]

A high step-up conversion-ratio converter with soft switching is presented in this paper. By using both coupled inductors and isolated transformer, high voltage gain can be easily achieved without extremely high duty ratio. To deal with switching losses, the active clamping circuit is adopted to achieve the zero-voltage-switching turn-on feature for power switches and to absorb the energy stored in the leakage inductor. Moreover, the series-resonant tanks composed by leakage inductors of the transformer and resonant capacitors are used to achieve the zero-current-switching turn-off feature for rectifier diodes at the output side. Therefore, the turn-on switching loss of power switches and the reverse-recovery problem of rectifier diodes can be eliminated. The operational principles and design consideration are discussed in detail. Finally, experimental results taken from a 400-W prototype are presented to confirm the effectiveness of the proposed converter. [ABSTRACT FROM AUTHOR]

A dual resonant converter with two transformers is presented in this paper. Dual resonant tanks are composed of leakage inductors and resonant capacitors to achieve zero-current-switching turnoff for rectifier diodes at the secondary side of the transformer. Hence, the reverse-recovery problem of the rectifier diodes can be eliminated. Moreover, the active-clamp circuit does not only absorb the energy stored in the leakage inductor but also clamp the voltage stress of power switches. Compared to the conventional dual resonant converter, the zero-voltage switching operation of the proposed converter is easily achieved by using two transformers. The operation principles, design considerations, and realization are discussed in detail. Finally, experimental results from a 400-W laboratory prototype are presented to confirm the effectiveness of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper proposes a twin-buck converter with zero-voltage transition (ZVT). The converter comprises two identical buck conversion units employing power MOSFETs as the active power switches with an interleaved inductor. The ZVT is accomplished by resonating the currents between the interleaved inductor and the parasitic capacitances of the power MOSFETs. The detailed circuit operations and analysis are provided. A laboratory circuit rated at 300 W is designed and tested. Experimental results show that the switching losses can be effectively reduced by ZVT of the active power switches, accompanied by the reduced reverse recovery loss of freewheeling diodes. [ABSTRACT FROM AUTHOR]

A novel zero-voltage-transition high-efficiency bridgeless power-factor-correction (PFC) circuit with a zero-current-switching auxiliary switch was proposed, analyzed, and experimentally verified. An assist circuit, consisting of a resonant inductor, two blocking diodes, a clamping circuit, an autotransformer, and an auxiliary MOSFET switch, was used to reduce the turn-on switching loss of the two main switches of the bridgeless PFC circuit and the turn-off switching loss of the auxiliary switch. The soft commutation of the main switches is achieved without imposing an additional voltage stress on the main switches. Feedback gate-drive signals can be obtained by using an existing converter IC controller modified to fit the purpose. In this paper, a detailed description of the circuit operation will be given. Based on the analysis, the guidelines for the component selection are presented. A prototype of 100-kHz 600-W universal-line PFC bridgeless circuit was built to verify the proposed scheme. In addition, based on the same concept, a family of bridgeless PFC configuration was proposed. [ABSTRACT FROM AUTHOR]

A newly designed zero-voltage-switching (ZVS) multi-input converter is proposed in this paper. The converter can boost the different voltages of two power sources to a stable output voltage. An auxiliary circuit is employed for achieving turn-on ZVS of all switches in the proposed converter. According to various situations, the operational states of the proposed converter can be divided into two states, including a single-power-supply and a dual-power-supply state. In the dual-power-supply state, the input circuits connected in series together with the designed pulsewidth modulation can greatly reduce the conduction loss of the switches. In addition, the effectiveness of the designed circuit topology and the ZVS properties are verified by experimental results, and the goal of high-efficiency conversion can be obtained. [ABSTRACT FROM AUTHOR]

The focus of this paper is the study of direct alternating-current (ac)–ac converters, beginning by buck, half-bridge, full-bridge, and push–pull converters. From the basic converters, we apply a simple methodology to make the use of switches in commercial configurations possible. Following that, eight voltage restorers supplied either on the line side or on the load side are proposed. A comparative evaluation of these topologies concerning implementation, complexity, and component effort is presented. It is notable that some of the studied topologies are known in the literature and others are new. For one of the presented topologies, the design of a 3-kVA voltage restorer is developed, and experimental results are shown, certifying the correct operation of the drive strategy used. [ABSTRACT FROM AUTHOR]

In this paper, a robust digital voltage-mode controller (DVMC) is proposed for a fifth-order boost point-of-load converter. Salient features of the proposed topology are compared with a conventional boost converter. Mathematical models are formulated using a discrete-time modeling technique and then employed in the compensator design, which uses the digital direct design approach. The DVMC is designed to ensure load voltage regulation. Robustness theory is applied directly in the digital domain, and then, various robust stability criteria describing sensitivity functions are formulated. The controller is designed to satisfy robustness criteria and then evaluated over a range of disturbances in spite of the fact that it maintains regulation. To confirm this, design simulations have been carried out on a 25-W 12–36-V converter system. Experimental results are provided to validate the concept and also to verify the range over which the designed controller is robust. [ABSTRACT FROM AUTHOR]