Search

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

In this paper, a series-capacitor-based interleaving buck power factor correction (PFC) converter is proposed, the intermediate energy storage capacitance of which is operated at discontinuous capacitor voltage mode (DCVM), and automatic power factor (PF) correction for this converter is obtained. Moreover, the voltage across the series capacitor of the proposed PFC converter is clamped at the input voltage, and thus peak voltage stress existed in the traditional DCVM buck PFC could be relieved. By effectively regulating the charge/discharge time for the series capacitor, ultrahigh step-down conversion ratio of the proposed converter is achieved, the conversion ratio of which is independent of the duty cycle and only related to the switching frequency and circuit parameters. Therefore, high PF can be obtained due to very narrow deadtime of the input current. Meanwhile, the proposed PFC converter can realize the soft turn-on of part power switch and soft turn-off of part power diodes. In addition, comparing with the traditional discontinuous inductor current mode PFC, the input current of the proposed PFC converter is continuous so that the peak value and root-mean-square value of input current can be reduced. The operational principle, performance analysis, and parameter design principle are given in this paper. The analysis results show that the PF and total harmonic distortion are also independent of the duty cycle. Finally, a 220-Vac input, 60 W/15 V output experimental prototype is built to verify the validity of the theoretical analysis. [ABSTRACT FROM AUTHOR]

The extra-LC auxiliary-resonant-snubber-based converter (ELCARSC), as a soft-switching converter, has the advantages of low switching loss, low electromagnetic interference noise, and low-output distortion caused by the dead-time effect. However, the dead-time effect is still the main problem in a high-precision application. Besides, the traditional control and compensation methods rely on the accuracy of the circuit parameters, especially the junction capacitance, thus resulting in compensation error. Therefore, this paper proposed a novel high-precision control method through modulating the initial resonant current to eliminate the dead-time effect of ELCARSC. The method does not need complicated online calculation and reduces the dependence on the accuracy of the circuit parameters, especially the influence of the junction capacitances of the switches. In this paper, the dead-time effect of the ELCARSC is analyzed. The output voltage error with the conventional variable-timing control method is analyzed. Subsequently, the proposed modulated initial resonant current control is introduced. Finally, a prototype was developed that verified the effectiveness of the control method. The quality of the output current and voltage is improved by utilizing the proposed control method. However, the peak current of the auxiliary switch is increased. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

In this paper, new half-bridge and full-bridge topologies for a switched-boost inverter are proposed. These topologies have a high boost factor in comparison with conventional types. In addition, the proposed topologies have continuous input current and can generate zero-voltage level in output. In this paper, the operation of the proposed inverters in different operating modes is analyzed. Then, the values of inductors and capacitors are designed. Moreover, the used switching pattern and its logical diagram are introduced. A comprehensive comparison between the proposed and conventional topologies in terms of the boost factor, the number of elements, and the efficiency shows the good features of the proposed inverters. Finally, to verify correct operation of the proposed topologies and derived equations, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper proposes a wide-range zero-voltage-switching (ZVS) active-clamped current-fed push–pull converter for fuel cell application. The presented converter achieves ZVS for all of the primary switches and ZCS for secondary diodes from rated load to 10% full load over the wide input voltage variation, improving the overall efficiency. The ZVS of switches is realized by the energy stored in the transformer leakage inductance aided by the secondary parallel inductor. An additional active clamping circuit suppresses the voltage spike as well as assists in realizing ZVS of switches. Low-voltage-rated switches with low on-state resistance can be used. Moreover, the voltage-doubler rectifier is adopted to release the reverse-recovery problem of rectifier diodes and reduce turns ratio of the high-frequency transformer. Detailed steady-state operation, analysis, design, control, comparative study, and experimental results are discussed in depth in this paper. Finally, a 200-W prototype has been built in the laboratory to verify the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, two topologies are presented for the enhanced-boost quasi-Z-source inverters (qZSI), namely continuous input current configuration and discontinuous input current configuration of enhanced-boost qZSI with two-switched impedance networks. Similar to enhanced-boost impedance-source inverters (ZSIs), these proposed inverter topologies possess very high boost voltage inversion at low shoot-through duty ratio and high modulation index to provide an improved quality output voltage. Compared to enhanced-boost ZSIs with two-switched Z-source impedance networks, these proposed inverter topologies share common ground with source and bridge inverter, overcome the starting inrush problem, and draw continuous input current and the lower voltage across the capacitors. Moreover, the input ripple current is negligible. This paper presents the operating principles and analysis of continuous input current configuration enhanced-boost qZSI with two-switched impedance networks and compares with ZSI, switched inductor ZSI, DA/CA-qZSI, and enhanced-boost ZSIs. The theoretical analysis is done and is validated through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, a voltage sensorless controller is developed for a two-switch single-phase rectifier that involves power factor correction and active pulsating power buffering without electrolytic capacitors. While a two-switch rectifier normally requires four sensed signals for control, only one current sensor is required in this proposal, thereby offering advantages such as low cost, high compactness, isolation between control and power circuits, and improved reliability. While the basic operating principle follows that of a conventional voltage sensorless controller for single-switch converters, several critical design considerations are the key to the success of the implementation which is explained in detail. The feasibilities of the controller are experimentally testified with a 100-W rectifier prototype regarding both steady state and dynamic performance. [ABSTRACT FROM AUTHOR]

For photovoltaic applications, the flyback microinverter with pseudo-dc-link is popular as a simple topology but brings large transformer turns ratio and thus large leakage inductance, which would deteriorate the converter efficiency. To solve this issue, based on the nonisolated pseudo-dc-link structure, this paper proposed a hybrid boost–flyback/flyback (BF/F) microinverter. This new topology is operated at the BF mode for the most segment of a half grid cycle and the F mode for the rest. During the BF mode, high voltage gain with low voltage stress is easily available in minimized transformer turns ratio. Besides, the leakage energy is recycled and the turn-off voltage spike of the main switch is clamped, as a result of a passive snubber inherently contained in this mode. Given that the BF mode is lack of step-down function, the F mode is developed to regulate the output voltage even for values lower than the input voltage. The operation and characteristic of the hybrid BF/F microinverter in boundary conduction mode are analyzed in detail, and the mathematical expression of reference current is derived theoretically to guarantee high power quality. Finally, a 240 W prototype was implemented to validate the theoretical analysis and the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper proposes a novel isolated high step-down conversion circuit, called an integrated buck and modified push−pull (IBMPP) converter, which is able to lower the voltage level on the primary side of the ideal transformer, resulting in a lower turns-ratio and decreased leakage inductance. The IBMPP converter is able to prevent the duty cycle from operating in extremely low conditions. Furthermore, the proposed converter adopts active-clamp techniques to recycle leakage energy and to suppress voltage spikes, so that the conversion efficiency can be effectively improved. The advantages of the IBMPP converter are its simple topology, easy control mechanism (which requires only two signals with a 180-degree phase shift), high conversion ratio, low component counts for power switches, and less voltage stress on some of the switches on the high-voltage side. The operation principle, steady-state analysis, design considerations, and experimental results of the proposed IBMPP converter are presented in detail. The feasibility of the IBMPP is verified by hardware implementation. The full-load efficiency at 250 W is 81.44%, and the input and output voltages are 380 and 5 V, respectively. [ABSTRACT FROM AUTHOR]

In this paper, a new high voltage gain step-up dc–dc converter is proposed for interfacing renewable power generation. The configuration optimally integrates both the coupled-inductor and switched-capacitor techniques to achieve an ultra-high step-up gain of voltage conversion with low voltage stress and high efficiency. It consists of a voltage boost unit, a passive clamp circuit, and a symmetrical voltage multiplier network. The structure becomes modular and extendable without adding any extra winding for ultra-high step-up voltage gain. The proposed topology not only reduces the voltage stress on the main switch but also maintains it steady for the entire duty cycle range. Furthermore, the reverse recovery issue of the diodes is alleviated through the leakage inductance of the coupled inductor. The operation principle and steady-state analysis are presented in detail. Experimental evaluation validates the claimed advantages and demonstrates a well-distributed efficiency curve and the peak of 96.70%. [ABSTRACT FROM AUTHOR]

This paper proposes two coupled-inductors-based Z-source networks, called the modified series and tapped switched-coupled-inductors quasi-Z-source networks (mSSCL-qZSN and mTSCL-qZSN, respectively). These networks offer high voltage gains with less-than-unity winding turn ratios $(n < {\text{1)}}$ , resulting in a reduced inductive element size. Other advantages include a less number of active components and their lower ratings and a higher efficiency. In addition, a lower magnetic core size is required for the proposed ZSNs due to the lower peak magnetizing current. The performance principles and detailed comparative analysis are provided and confirmed through experiments on a 200-W dc–dc converter. [ABSTRACT FROM AUTHOR]

In this paper, a nonisolated bidirectional dc–dc converter is presented. The proposed converter consists of two boost converters to enhance the voltage gain. Four power switches with their body diodes are employed in the proposed converter. Also, two inductors and a capacitor are used as passive components. The input current is divided to the inductors which causes the efficiency to be high. The voltage gain of the proposed converter is higher than the conventional cascaded bidirectional buck/boost converter (CCBC) in step-up mode. Besides, the voltage gain in step-down mode is lower than CCBC. Besides, the efficiency of the proposed converter more than CCBC while the total stress on active switches are same. The simple structure of the proposed converter causes its control to be easy. The steady-state analysis of the proposed converter is discussed in this paper thoroughly. The stress on converters’ devices and the efficiency of the proposed converter and CCBC are compared in this paper. Finally, the proposed converter prototype circuit is implemented to justify the validity of the analysis. [ABSTRACT FROM PUBLISHER]

In this paper, a new multi-input multi-output (MIMO) dc–dc converter with high step-up capability is proposed for wide power ranges. Also, in order to increase each output voltage, diode–capacitor voltage multiplier (VM) stages are utilized in the proposed converter. The number of input stages, output stages, and VM stages are arbitrary and dependent on design conditions. At first, the general structure of proposed MIMO converter is presented. Then, in order to explain the converter operation, we walk through the design of a 1-kW four-input two-output example, including loss and efficiency calculations. We validate the design with a prototype that matches efficiency calculations. [ABSTRACT FROM AUTHOR]

In this paper, an input-series flyback converter with the coupled-inductor-based passive snubber is proposed, where the input-series converter is based on transformer integration, and the passive snubber is composed of inductors, capacitors, and diodes. The inductors of the snubber in various series modules are made on a common magnetic core, and the coupled-inductor scheme is adopted. With the help of the coupled inductor, active input voltage sharing of the input-series converter can also be achieved after the switches are turned off, and voltage sharing of the switch in each series module can be ensured, which overcome the shortcomings of the existing input-series flyback converter. Active voltage sharing processes caused by the coupled inductor are analyzed in detail. Furthermore, the design guideline of the passive snubber is discussed. Finally, the experimental study has been done on a 1500 Vdc/60 W laboratory-made prototype composed of three flyback series modules, and the feasibility of the proposed method and the theoretical analysis is verified by the experimental results. [ABSTRACT FROM AUTHOR]

In this paper, an expandable single-input three-output high step-up dc–dc boost converter is proposed. The voltage conversion ratio of the output ports of the converter can be increased by inductor-diode-capacitor and diode-capacitor cells. The proposed converter can be applied in renewable energy conversion systems, such as in photovoltaic and fuel cells. Also, due to the three output ports of the converter, it can be utilized in portable devices which require high voltage conversions. The main advantage of the proposed converter is supplying loads with different voltages and current ranges due to the expandable structure of the converter. Besides, the proposed converter has the merit of achieving high voltage gains at high frequencies without preselecting wide duty cycles. Furthermore, the proposed converter is able to achieve higher voltage ranges without having any transformer or coupled inductors in its structure; consequently, the related drawbacks are avoided. The switching pattern of the converter is simple and both switches are on and off simultaneously. In this study, a single switching period of the proposed converter, the voltage conversion ratios of the output ports and the expanded form of the structure are analyzed theoretically. Finally, to verify the theoretical results, the experimental results for 40-V input/200-V, 100-V and 360-V outputs with total 600-W output power are extracted and compared with each other. [ABSTRACT FROM AUTHOR]

In recent years, modular multilevel converter (MMC) is considered for medium-voltage variable speed drives (VSD) due to its modularity and higher reliability. However, the major drawback of the MMC-based VSD is the higher capacitor ripple voltage at lower operating speeds. In literature, this ripple voltage is reduced by injecting a high-frequency circulating current into each arm. This additional circulating current increases the overall current rating of the devices, inductors, and capacitors. Alternatively, the capacitor ripple voltage can be reduced at the lower output frequency by reducing the dc-bus voltage. This paper proposes a new configuration using a multipulse diode-bridge rectifier to reduce the dc-bus voltage when the drive is operated at lower speeds. Therefore, the capacitor ripple voltage decreases without injecting any circulating current. In addition, a new technique is proposed to maintain the peak-to-peak value of the submodule capacitor ripple voltage constant at near-zero speed. The proposed converter with 24-pulse rectifier configuration is simulated in MATLAB/Simulink, and the experimental validation is carried out on a prototype with 12-pulse rectifier. [ABSTRACT FROM AUTHOR]

Three-phase bridge converter is popular in ac–dc power conversion. The conventional sensor control with inner current loop and outer voltage loop is often used to control the three-phase bridge converter. Many three-phase sensorless control methods had been proposed to control the bridge converter with considering the inductance and inductor resistance. In this paper, the voltage drop of the power semiconductor is first considered in the proposed three-phase current sensorless control method. At first, the dynamic behaviors of three-phase bridge converter for power factor correction (PFC) applications are studied, and its equivalent three-switch model is developed. Based on this developed model, three-phase current sensorless control with only voltage controller is proposed. Additionally, the voltage-loop transfer function of PFC bridge converter controlled by the proposed method is modeled, and the result is helpful to obtain the controller parameter. The proposed control method is implemented on the DSP-based platform for evaluation. Finally, the provided simulation and experimental results demonstrate the performance of the proposed method. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high step-up dc–dc converter is proposed. Active–passive inductor cells (APICs) are used to extend the topology. The ability to achieve high gains is the main merit of the proposed topology. The proposed converter operates based on parallel charging and series discharging of the inductors. The converter also achieves high step-up voltage gain with appropriate duty cycle and low voltage and current stress on the power switches and diodes. The proposed converter is analyzed in operation modes. The main parameters of the converter such as voltage gain, voltage stress of semiconductor devices are calculated to compare with other structures. Considering the output voltage ripple and filter size, the proposed converter is designed. Moreover, the losses and efficiency of the converter are calculated. The performance of the proposed converter is validated by experimental results. [ABSTRACT FROM AUTHOR]

In this paper, a novel transformerless interleaved high step-down conversion ratio dc–dc converter with low switch voltage stress is proposed. In the proposed converter, two input capacitors are series-charged by the input voltage and parallel-discharged by a new two-phase interleaved buck converter for providing a much higher step-down conversion ratio without adopting an extreme short duty cycle. Based on the capacitive voltage division, the main objectives of the new voltage-divider circuit in the converter are for both storing energy in the blocking capacitors for increasing the step-down conversion ratio and reducing voltage stresses of active switches. As a result, the proposed converter topology possesses the low switch voltage stress characteristic. This will allow one to choose lower voltage rating MOSFETs to reduce both switching and conduction losses, and the overall efficiency is consequently improved. Moreover, due to the charge balance of the blocking capacitor, the converter features automatic uniform current sharing characteristic of the interleaved phases without adding extra circuitry or complex control methods. The operation principles and relevant analysis of the proposed converter are presented in this paper. Finally, a 400-V input voltage, 25-V output voltage, and 400-W output power prototype circuit is implemented in the laboratory to verify the performance. [ABSTRACT FROM PUBLISHER]

Peak current mode (PCM) control has been widely used for the control of switching dc–dc converters due to its excellent transient performance. With the development of single-inductor dual-output (SIDO) dc–dc converters, PCM control technique is introduced to the control of SIDO dc–dc converters. Conventional PCM buck converter has only one reference current, with two inductor current borderlines are used to divide the operation modes of inductor current. However, PCM SIDO buck converter has more inductor current borderlines as it has one more reference current than that of PCM buck converter. In this paper, inductor current borderlines of PCM SIDO buck converter are investigated, and unified discrete iterative model of PCM SIDO buck converter is established. The effect of the difference of reference currents, initial inductor current and input voltage on the stability of PCM SIDO buck converter has been discussed by using bifurcation diagrams. The study results show that the stability of PCM SIDO buck converter is sensitive to the difference of reference currents, initial inductor current and input voltage. The stability boundary of the difference of reference currents, stability region of initial inductor current, and stability boundary of input voltage are derived. Lyapunov exponent and experimental results are carried out to verify the theoretical analysis results. [ABSTRACT FROM PUBLISHER]

Due to the relatively low output voltage of photovoltaic (PV) source, a high step-up converter with high efficiency is needed when the PV source is connected to the power grid. A novel high step-up converter based on two switched capacitors and a coupled inductor is proposed in this paper. The operating principle is analyzed and the voltage gain is derived. A 100-W prototype is fabricated in the laboratory to verify the theoretical analysis, and the highest efficiency is 96.4%. [ABSTRACT FROM PUBLISHER]

This paper extends the trans-Z-source concept to ac–ac power conversion and proposes a novel single-phase trans-Z-source ac–ac converter. The proposed converter retains the advantages of its existing Z-source/quasi-Z-source counterparts in which the output voltage can be boosted and in-phase with the input voltage or bucked/boosted and out-of-phase with the input voltage. Meanwhile, a coupled inductor is introduced into the proposed converter, and the turns ratio of the coupled inductor become another control variable beside the duty cycle to obtain extreme voltage gain. Importantly, the input voltage and output voltage share the same ground, and the input current could be continuous, which is a benefit for reducing input current harmonics. Most important of all, the safe-commutation strategy for the proposed converter is deep developed, and analytic expression between the switches state and loop circuit voltage/current condition is derived out. Hence, the current/voltage ripple can be avoided without a loss snubber circuit, which benefits a reduced cost and enhanced reliability. The performance analysis is discussed in consideration of parasitic resistance, and system parameter design is optimized based on theoretic calculation. A laboratory prototype is fabricated, and experiments are performed to verify the validation of the proposed converter. [ABSTRACT FROM PUBLISHER]

A common ground switched-quasi-Z-source bidirectional dc–dc converter is proposed for electric vehicles with hybrid energy sources. The proposed converter is based on the traditional two-level quasi- Z-source bidirectional dc–dc converter, changing the position of the main power switch. It has the advantages of a wide-voltage-gain range, a lower voltage stress across the power switches, and an absolute common ground. The operating principle, the voltage and current stresses on the power switches, the comparisons with the other converters, the small signal analysis, and the controller design are presented in this paper. Finally, a 300 W prototype with $U_{{\rm{high}}}= {240 \ \rm{V}}$ and $U_{{\rm{low}}}= {40\sim 120\ \rm{V}}$ is developed, and the experimental results validate the performance and the feasibility of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, dual-buck structured single-stage buck–boost inverters that use power MOSFETs to achieve high efficiency are presented. The proposed inverters require fewer switches, and half of the switches have reduced current stresses. They have no shoot-through problem; therefore, high system reliability can be obtained. The dead-time in PWM signals can be minimized or eliminated, which improving the quality of the output ac voltages and increasing the efficiency. In the proposed inverters, MOSFETs can be used without reverse-recovery issues of their body diodes to boost the efficiency and increase the switching frequency. To further improve the efficiency and stability of the proposed single-phase inverter, PWM strategies combining high- and low-frequency modulation are presented. A hardware prototype of the single-phase inverter was built and tested using resistive, inductive, and nonlinear loads. Experimental results for a 300-W prototype inverter show a 97.4% peak efficiency with a 25 kHz switching frequency. [ABSTRACT FROM AUTHOR]

The parallel three-phase grid-connected converters sharing dc and ac bus can increase the system power level effectively. However, the zero sequence circulating current (ZSCC) will occur inevitably under space vector pulse width modulation or discontinuous pulse width modulation (DPWM). In this paper, the mechanism and the mathematical model of ZSCC are studied. Then, a hybrid PWM (HPWM) strategy is proposed to suppress the ZSCC based on the same zero sequence voltage injected, which is dependent on the common grid information. The dc voltage utilization of HPWM can be extended compared with sinusoidal PWM (SPWM). The number of parallel modules can be infinity theoretically by using HPWM. It is noted that there is no internal commutation among modules (expect the dq current reference). Finally, the feasibility and the effectiveness of the proposed method are verified by experiments. [ABSTRACT FROM AUTHOR]

The battery energy-stored quasi-Z-source (BES-qZS)-based photovoltaic (PV) power generation system combines advantages of the qZS inverter and the battery energy storage system. However, the second-harmonic ( \text2\omega ) power ripple degrades the system's performance and affects the system's design. An accurate model to analyze the \text2\omega ripple is very important. The existing models did not consider the battery, or assumed a symmetric qZS network with $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$, which limits the design freedom and causes oversized impedance parameters. This paper proposes a comprehensive model for the single-phase BES-qZS-PV inverter system, where the battery is considered and there is no restriction of $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$ . Based on the built model, a BES-qZS impedance design method is proposed to mitigate the \text2\omega ripple with asymmetric qZS network. Simulation and experimental results verify the proposed \text2\omega ripple model and impedance design method. [ABSTRACT FROM AUTHOR]

This paper proposes an isolated single-ended primary-inductor converter (SEPIC) dc–dc converter with ripple-free input current and lossless snubber. The proposed converter is based on a conventional isolated SEPIC converter to enable electrical isolation and high voltage gain using a coupled inductor. The input current ripple is significantly reduced by utilizing an auxiliary circuit that also functions as a lossless snubber circuit with an additional diode. Moreover, the maximum switch voltage stress is clamped to a low voltage by the snubber circuit. Therefore, a low voltage rating mosfet that has low $R_{{\rm{DS(on)}}}$ can be utilized as a main switch device. Hence, the total power efficiency is improved. Experimental results from a 100 W prototype, which are presented to verify the theoretic analysis and performance of the proposed converter. [ABSTRACT FROM PUBLISHER]

DC microgrids are popular due to the integration of renewable energy sources such as solar photovoltaics and fuel cells. Owing to the low output voltage of these dc power generators, high efficient high gain dc–dc converters are in need to connect the dc microgrid. In this paper, a nonisolated high gain dc–dc converter is proposed without using the voltage multiplier cell and/or hybrid switched-capacitor technique. The proposed topology utilizes two nonisolated inductors that are connected in series/parallel during discharging/charging mode. The operation of switches with two different duty ratios is the main advantage of the converter to achieve high voltage gain without using extreme duty ratio. The steady-state analysis of the proposed converter using two different duty ratios is discussed in detail. In addition, a 100 W, 20/200 V prototype circuit of the high gain dc–dc converter is developed, and the performance is validated using experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, a single-phase multilevel ac/ac converter with reduced number of power semiconductor devices is proposed. For the simple case of a three-level converter, only three bidirectional switches and two capacitors are required. The proposed converter provides a highly sinusoidal and regulated output voltage with a simple topology. The efficiency is high because in each state of operation only one semiconductor conducts. The converter can be easily extended to any desired levels in the output voltage to even more reduce the output total harmonics distortion. Another advantage of the proposed converter is that by increasing the voltage levels, the stress on the switches will decrease. The proper performance of the proposed converter is confirmed through extensive simulation and experimental tests. [ABSTRACT FROM PUBLISHER]

In this paper, a power factor correction (PFC)-based switched reluctance motor (SRM) drive is proposed. Generally, the SRM drive is fed with a simple diode bridge rectifier followed by a bulky capacitor, which draws peaky current at low power factor and high-input-current total harmonic distortion (THD). Here, a dual output converter is proposed to control the SRM and to provide power quality improvement as well. This converter is a combination of Cuk and SEPIC converters, which produces two equal output voltages with neutral point N, to feed a midpoint converter of the SRM drive. The converter is designed to operate in discontinuous conduction mode of operation to obtain inherent PFC at supply side. The motor control is attained by regulating dc link voltage over a wide range. Test results on a prototype of the SRM drive demonstrate the excellent performance with high power factor and reduced input current THD. The observed power quality indices depict the improved power quality as per the standard IEC 61000-3-2. [ABSTRACT FROM PUBLISHER]

This paper proposes a single-stage light-emitting diode (LED) driver based on an inverted buck topology, using current path control switches. The proposed circuit consists of a control circuit, a bridge diode, and an inverted buck converter with multiple switches connected to the LED segments in parallel. Whereas the typical buck LED driver operates with a fixed LED forward voltage, the proposed driver operates with a variable LED forward voltage, according to the input voltage level. Because of this capability to adjust the LED forward voltage, it can reduce the current ripple and the switching frequency with a small inductance value. In addition, it enables operation with LED lamps of a wide voltage range, while simultaneously achieving small dead-angles. The detailed operation principles are described, and the design considerations for the proposed driver are discussed. The proposed driver circuit and control operation are verified experimentally using a 7 W hardware prototype with four LED segments. The obtained experimental results show that under a 110 Vrms input voltage, the proposed driver achieves a power factor of 0.94 with a small dead-angle and an efficiency of 94%. [ABSTRACT FROM PUBLISHER]

In this paper, a new type of matrix converter (MC) also called a single-phase high-frequency transformer isolated (HFTI) buck MC is proposed. The proposed converter can provide step-down operation of the input voltage with various types of output voltages such as in-phase and out-of-phase output voltages, rectified (or positive) output voltage, and output voltage with step-changed frequency. By incorporating HFT isolation, the proposed MC saves an extra bulky line frequency transformer, which is required for the conventional MCs to provide electrical isolation and safety, when used in application such as dynamic voltage restorers, etc. Two different circuit variations of the proposed HFTI MC are presented with and without continuous output currents, with the latter having less passive components. The safe-commutation strategy is also employed for the proposed HFTI MC to provide current path for the inductor during dead-time, which avoids switch voltage spikes without adding any snubber circuits. The operation principle and circuit analysis of the proposed MC are presented, and switching strategies are also developed to obtain various output voltages. Moreover, a prototype of the proposed MC is fabricated, and experiments are performed to produce in-phase/out-of-phase and rectified output voltages, and output voltage with step-changed frequency. [ABSTRACT FROM PUBLISHER]

This paper presents a new buck–boost converter. Unlike the single-switch buck–boost converter, the proposed converter has low-voltage stresses on semiconductors. Moreover, although both the conventional two-switch buck–boost (TSBB) and the proposed converters have the same number of passive and active components, and the proposed converter can reduce the conduction loss as a result of having fewer conducting components. Therefore, the proposed converter obtained a higher efficiency than the TSBB converter. A 48-V output voltage and 150-W output power prototype was fabricated to verify the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, a design method is proposed for finding the equivalent inductance and capacitance of the single-ended primary-inductor converter (SEPIC). The relations of the output voltage ripple (OVR) of the SEPIC converter are obtained in complete inductor supply mode–continuous conduction mode (CISM-CCM), incomplete inductor supply mode-CCM (IISM-CCM), and IISM-discontinuous conduction mode (IISM-DCM). The maximum of OVR (MOVR) is investigated for a specified range of the input voltage and load resistance. This value of the MOVR is obtained for the minimum values of input voltage and load resistance. In this paper, the minimum values of the equivalent inductance and capacitance are calculated in obtaining the minimum value of the MOVR. One of the other performed studies in this paper is calculation of the switch peak current in CCM and DCM. In addition, the converter is designed based on the minimum values of the MOVR and stress of the switching current. Experimental and simulation results are used to prove the validity of the presented theoretical subjects. [ABSTRACT FROM PUBLISHER]

The Z-source inverter (ZSI) employs an LC impedance network between the main inverter bridge and the power source. The unique feature of the ZSI is that it can operate either in buck or boost mode with a wide range of obtainable output voltages from a given input voltage. This topology also exhibits better electromagnetic-interference noise immunity when compared to a traditional voltage-source inverter (VSI). However, the LC impedance network of ZSI significantly increases the size and cost of the power converter and can make it unsuitable for low-power applications. This paper proposes a novel topology called switched boost inverter (SBI) which exhibits similar advantages of ZSI with lower number of passive components and more active components compared to ZSI. The steady-state and small-signal analyses of SBI, along with its pulsewidth modulation (PWM) control strategies, have been discussed in this paper. This paper also presents a comparison of SBI and ZSI with the same input and output parameters. The theoretical analysis given in this paper has been validated using a laboratory prototype of SBI, and the experimental results are presented for verification. The experimental harmonic spectrum of the inverter's output voltage with the proposed PWM technique is also plotted and compared with that of a traditional VSI. All the experimental results show good correlation between theory and experiments. [ABSTRACT FROM PUBLISHER]

A novel transformerless buck–boost dc–dc converter is proposed in this paper. The presented converter voltage gain is higher than that of the conventional boost, buck–boost, CUK, SEPIC, and ZETA converters, and high voltage can be obtained with a suitable duty cycle. In this converter, only one power switch is utilized. The voltage stress across the power switch is low. Hence, the low on-state resistance of the power switch can be selected to decrease conduction loss of the switch and improve efficiency. The presented converter has simple structure, therefore, the control of the proposed converter will be easy. The principle of operation and the mathematical analyses of the proposed converter are explained. The validity of the presented converter is verified by the experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents a new family of hybrid Z-source boost dc–dc converters intended for photovoltaic applications, where the high step-up dc–dc converters are demanded to boost the low-source voltages to a predefined grid voltage. Because the boost capabilities of the traditional Z-source networks are limited, the proposed converters are composed of combine traditional Z-source networks in different ways to enhance the boost abilities of the traditional Z-source networks. The new version of the proposed Z-source converters is termed as hybrid Z-source boost dc–dc converters to satisfy the traditional benefits of Z-source networks with stronger voltage boost abilities which can also be applied to dc–ac, ac–ac, and ac–dc power conversions. The performances of the proposed converters are compared with other Z-source networks behaviors. The simulation and experimental results of the proposed converters are validated at different operating conditions. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel high step-up nonisolated single switch dc–dc converter suitable for regulating dc bus in various microsources especially for photovoltaic (PV) sources. Quadratic boost and switched-capacitor technique are used as primary and secondary circuits, respectively. A coupled inductor is applied to make a connection between them, so a high dc voltage gain is achieved. High efficiency is yield where voltage stress on active switch is alleviated by clamped capacitor; consequently, smaller \rmR\rm{DS(ON)} for power switch is required. On the other hand, input current of the proposed converter is continued, hence stress on the input source is reduced. The operating principles and steady-state analyses are discussed in detail for both continuous and discontinuous conduction modes. Also, the boundary condition is computed. To verify the performance of the proposed converter and theoretical calculations, a 250-W prototype converter is implemented with an input voltage of 24 V and an output voltage of 400 V designed especially for PV sources in continuous conduction mode operation. Finally, simulation results are confirmed by experimental results; maximum efficiency is occurred at 150 W and full-load efficiency is 92.96%. [ABSTRACT FROM AUTHOR]

A new single-phase \uppi-\texttype 5-level inverter using 3-terminal switch-network (3TSN) is proposed in this paper. The topology is considered as a variant of T-type 3-level structure or dual-buck inverter with coupled inductors. This new inverter is suitable for multilevel power inversion with low dc-bus voltage. The merit of the proposed topology is to apply only four active power switches to achieve 5-level operation. Other benefits include double frequency operation of output inductor and equal division of the current that flows through power switches and filter inductor. Hence, it leads to high efficiency and low harmonics. These characteristics allow improvement of losses distribution and volume reduction of output filter inductor. The operation scenario with sinusoidal pulsewidth modulation (SPWM) is described in details. Meanwhile, the magnetic analysis and design are studied and discussed. Finally, a prototype is built to verify the theoretical analysis and demonstrate the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

In this paper, a novel four-phase interleaved high step-down converter is presented. The proposed converter can provide an extremely high step-down voltage conversion ratio within a moderate duty cycle. There are four main advantages of the proposed converter. First, the blocking capacitors can store energy as usual. Therefore, they are used as voltage sources to reduce the input voltage as well as to reduce the switch voltage stresses. Second, due to the charge balance of the dc blocking capacitors, the converter possesses an automatic uniform current sharing characteristic of the interleaved phases without adopting any extra circuitry. Third, due to the phase shift between the interleaved phases, the architecture provides a low output current ripple. Fourth, the number of phases can be expanded or reduced to any even phases; therefore, the converter has a wide range of applications. Finally, the operating principles and analysis of this architecture are given, and an experimental prototype is also provided to verify the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]

This paper presents a new formulation of a finite control set model-predictive control (FCS-MPC) algorithm, allowing to determine the best commutation instant in order to optimize the converter current tracking. This algorithm, mixing properties of FCS-MPC method and time resolution related to pulse width modulation schemes, is illustrated in a parallel flying capacitor converter. The parallel association of classical commutation cells is a good solution for increasing the output current driven by the converters, while the standard semiconductor technology is used. The control strategy used with this type of connection must be able to ensure not only a good distribution of the output current among the different legs, but also the balancing of the floating capacitor voltages. [ABSTRACT FROM PUBLISHER]

This paper introduces a new magnetically coupled single-switch nonisolated dc–dc converter with a high-voltage gain. The topology utilizes magnetic coupling for boosting its output voltage, but unlike other converters with coupled magnetics, its voltage gain is increased by reducing its magnetic turns ratio. The name “Trans-inverse (Tx−1)” is thus used for representing this inverse operating principle of the converter. The converter draws a continuous current from the source and is, hence, suitable for many types of renewable sources. Its leakage energy from the coupled magnetics has further been recycled and transferred to the load by an integrated regenerative snubber circuit. Its inclusion of dc-current-blocking capacitors has also helped to prevent core saturation, which, together with other performance features, has been verified experimentally. [ABSTRACT FROM PUBLISHER]

This paper presents a new dual-switch control structure for an ac/dc noninverting cascaded buck–boost power factor correction converter. The proposed converter operates at a discontinuous capacitor voltage mode providing an inherent high-power factor and a zero voltage turn-off switching. Additionally, the proposed control structure enables for a nondistorted sinusoidal current for a wide range of output voltage levels. Unlike the conventional methods, a mode detector is not required and consequently there is no hard transition between buck and boost modes. Although both converter switches are controlled, only one feedback control loop is required to obtain the desired power flow at a unity power factor. The principle of operation, theoretical analysis, simulation, and experimental results of a 1.6-kW prototype grid-connected converter are presented. The results confirmed the validity of the proposed system under various operating conditions. [ABSTRACT FROM PUBLISHER]

Semiactive quadrupler rectifiers (SAQRs) are proposed in this paper to serve as the secondary rectification circuits, which make the secondary-side voltages to be controllable and help reduce current stress and conduction losses. An interleaved isolated boost converter is developed based on the proposed SAQRs. By utilizing the pulse-width modulation (PWM) plus phase-shift (PPS) control strategy, the primary- and secondary-side voltages are well matched to reduce the current values and circulating conduction losses. With the proposed SAQRs, the voltage gain is extended and the voltage stresses on power devices and passive components used in rectification circuits are reduced to the half of the high output voltage. Hence, the efficiency is improved by using a transformer with a smaller turns ratio and reduced parasitic parameters, and by employing low-voltage rating devices with better switching and conduction performance. With optimal design, lower voltage, and current stresses on the primary-side switches, minimized input current ripple can be realized. Moreover, the zero-voltage turn on switching of the active switches and the zero-current turn off switching of the diodes can be achieved over a wide load and voltage range by the proposed SAQR-based converter and the control strategy. Meanwhile, the higher voltage gain, the lower voltage, and the current stresses on power devices can be obtained with the proposed SAQR-based converter compared with passive quadrupler rectifier-based converter. The feasibility and effectiveness of the proposed SAQRs and the derived converter are verified by a 380-V output prototype. [ABSTRACT FROM PUBLISHER]

Compared with constant duty cycle-controlled discontinuous conduction mode (DCM) boost power factor (PF) correction (PFC) converter, constant duty cycle-controlled quadratic DCM–DCM boost PFC converter features with much lower second-order line frequency output voltage ripple, and however, it suffers from low PF. To increase PF of quadratic DCM–DCM boost PFC converter, a variable duty cycle control technique for quadratic DCM–DCM boost PFC converter is presented in this paper. An approximation equivalent for the variable duty cycle is employed to simplify the implementation circuit. The corresponding expressions of PF and output voltage ripple are analyzed. For input voltage range of 100–240 Vac, quadratic DCM–DCM boost PFC converter with variable duty cycle control benefits with very high PF, and tradeoff between PF and output voltage ripple of this converter is analyzed. Experimental results from 100-W prototypes are given to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

In this paper, a new topology for half-bridge switched boost inverter (HB-SBI) is proposed. The proposed half-bridge inverter uses more active elements rather than capacitors and inductors in comparison with the conventional half-bridge Z-source inverter with two Z-networks, which results in reduction of weight, size, and cost. Moreover, the proposed inverter has the capability of eliminating inverter leg short-circuit issues and is able to further increase the output voltage level in comparison with its conventional types. Generating zero-level output voltage is also another advantage of this topology. Based on theoretical calculations, the steady-state and small-signal analysis of the proposed topology in different operating modes are performed and the ripple of inductors’ current and capacitors’ voltage are also calculated. A comprehensive comparison is also made between the proposed inverter and the conventional types. Finally, the experimental results are provided to reconfirm the performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

In this paper, a common grounded Z-source dc–dc converter with high voltage gain is proposed for photovoltaic (PV) applications, which require a relatively high output–input voltage conversion ratio. Compared with the traditional Z-source dc–dc converter, the proposed converter, which employs a conventional Z-source network, can obtain higher voltage gain and provide the common ground for the input and output without any additional components, which results in low cost and small size. Moreover, the proposed converter features low voltage stresses of the switch and diodes. Therefore, the efficiency and reliability of the proposed converter can be improved. The operating principle, parameters design, and comparison with other converters are analyzed. Simulation and experimental results are given to verify the aforementioned characteristics and theoretical analysis of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, the Class-Fn/E power amplifier (PA) and the inverse Class-E (Class- \mboxE^-1) PA under zero-current switching and zero-current-derivative switching conditions at any duty ratio are analyzed. The maximum switch voltage and current, output power capability, and element values as functions of the duty ratio are obtained for both classes. The main objective of the analysis is to choose the proper duty ratio to maximize the output power capabilities at optimum conditions. The element values are dependent upon the duty ratio and require a careful selection of the duty ratio to reach desired specification. The effect of the duty ratio D=0.3-0.7 on the performance of the Class- \mboxE^-1 and Class-F3/E PAs is demonstrated. The duty ratio is used not only as the design specification but also as the adjusting parameter for achieving a certain condition. The measured maximum drain efficiency of 88% and 87% are obtained at 4 MHz at 30-dBm input power for the Class-F3/E and Class- \mboxE^-1 PAs, respectively. The results show that lower peak switch voltage and current are obtained in the Class-F3/E PA in comparison with Class- \mboxE^-1 for the same conditions. [ABSTRACT FROM PUBLISHER]

This paper proposes a new topology for an enhanced-boost Z-source inverter (ZSI) with combined two Z-impedance networks. By two Z-impedance networks and low shoot-through duty cycle, the proposed inverter produces high output voltage gain. In traditional ZSIs for high boosting voltage, a low modulation index is required; hence, under these conditions, the output voltage will have low quality with high total harmonic distortion. Compared with the conventional high-boost ZSI topologies, the proposed inverter uses shorter shoot-through duration and a larger modulation index to improve the output waveform quality. Comparison between the proposed topology and previously proposed schemes, in terms of inductor numbers, voltage and current stresses on elements, sizes of inductors and capacitors, efficiency, and switching device product (SDP) factors of diodes, is made, and the results verify the priority of the proposed topology. The operating principle of the proposed topology is analyzed in detail. Both simulation and experimental results verify the high performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]