Search

In this paper, a family of three-phase direct pulse-width modulated (PWM) ac–ac converters consisting of buck, boost, and buck–boost converters is proposed. The proposed converters have no commutation problem even if all of the switches are turned on or off simultaneously. They do not use lossy snubbers and do not sense the voltage polarity for commutation, and produce high-quality output voltage waveforms. The proposed converters allow the use of power MOSFETs and fast recovery freewheeling diodes independently. The use of power MOSFETs as active switches and freewheeling diodes with extremely fast recovery features lower the switching losses and enable us to reduce the volume of passive components by increasing switching frequency. The input (or output) filter inductor experiences twice of the converter switching frequency and thus can be designed with minimum size. To increase power density of the proposed converters, a three-phase three-limb coupled inductor is proposed. Three-phase coupled inductor integrates three separate coupled inductors of the proposed converters in one three-limb core. In comparison with separate coupled inductors, the three-phase coupled inductor has a smaller size with large current-handling capability. Experimental results obtained for the boost-type converter show the robustness of the proposed three-phase ac–ac converters. [ABSTRACT FROM AUTHOR]

For discontinuous conduction mode (DCM) dc–dc converters with digital sensorless current mode (DSCM) control, an observed current error occurs, owing to a low-accuracy current observer. Moreover, a reference current error occurs due to a low-accuracy current controller or a finite dc gain of current loop. Conventionally, the observed current is compensated to increase current regulation accuracy, whereas the reference current error is neglected. However, for charge balance principle (CBP)-based DSCM (CBP-DSCM) control, this paper proves that the reference current should be compensated in a same quantity to that of observed current. Otherwise, single or unequal compensation leads to output voltage steady-state error. For this reason, a dual current error compensation strategy for CBP-DSCM control is proposed. It compensates the errors in a same quantity through a current error observer, which considers parasitics and calculates the current errors without approximation. To verify the proposed strategy, small-signal models with parasitics for both the converter and the controller are constructed by differential functions of key variables. Furthermore, converter stability is analyzed at typical operation condition, while the stability at various operation conditions is verified through robustness analysis. Finally, simulations and experimental results verify the analysis and the improved transient response of the converter. [ABSTRACT FROM AUTHOR]

A high-voltage tapped-inductor buck converter utilizing a novel autonomous high-voltage valve is presented in this paper. Its application as auxiliary power supply for high-power cascaded-converter submodules is discussed, followed by a presentation of the most challenging problems in designing a low-power high-voltage step-down converter. The TI-buck converter topology is analyzed, which together with the novel autonomous high-voltage valve overcomes most of the problems. Analytical expressions describing the operation as well as circuit simulations are presented. Finally, an experimental evaluation of a 3-kV 70-W prototype converter utilizing the proposed autonomous high-voltage valve with series-connected super-junction MOSFETs is presented. [ABSTRACT FROM PUBLISHER]

Conventional matrix converters (MCs) have limited voltage gain that is less than 0.866, whether for direct MC (DMC) or indirect MC (IMC). Existing Z-source (ZS)/discontinuous quasi-Z-source (qZS) DMCs and ZS IMCs achieved larger than 0.866 voltage gain; however, the former inherited the complex commutation from DMC, and the latter involved a ZS network in dc link and led to non-all-silicon solution. In this paper, ZS and discontinuous qZS networks of existing ZS/qZS DMCs are used for an IMC topology for simplifying commutation and having high voltage gain, but they require extra input filter to reduce current harmonics. A new continuous qZS IMC is proposed, where a qZS network integrates the filtering function of the grid side; hence, additional input filter is avoided in the proposed continuous qZS IMC. Three new IMCs are compared in detail, in terms of voltage gain, current ripple, voltage ripple, inductor current and capacitor voltage stresses, ZS/qZS switch current and voltage stresses, filtering function, input current total harmonic distortion (THD), output voltage THD, and efficiency. Their control and modulation methods are presented to achieve the desired performances. Experimental comparisons verify the theoretical analysis and that the proposed continuous qZS IMC is a promising topology. [ABSTRACT FROM PUBLISHER]

Affected by the equivalent series resistance (ESR) of the devices in the circuit, the voltage-conversion ratio of traditional boost converter is limited. Various topologies have been developed to provide a high step-up voltage gain. An inherent high voltage gain can be achieved in a dual-switch converter with the advantages of low voltage and current stress on the switches. However, this converter has a strict requirement of the parameters' consistency. This paper discusses the steady-state operation principle of the converter in detail under the condition that the parameters are inconsistent and then illustrates the solutions to balance the voltage on the switches and suppress the resonance with passive lossless clamping. Finally, a prototype has been established in the laboratory, and simulation and experimental results have been given to verify the analysis and the effectiveness of clamping method. [ABSTRACT FROM PUBLISHER]

This paper presents a dc–dc boost converter with high voltage gain based on the three-state switching cell for split-capacitor neutral-point-clamped inverters. The proposed converter is analyzed considering the operation in continuous conduction mode and duty cycle higher than 0.5, which corresponds to overlapping mode. The main characteristics of the topology are operation at high switching frequency, whereas the input inductor is designed for twice such frequency; in order to minimize weight and volume, the voltage stress across the switches is lower than half of the output voltage and naturally clamped by one output capacitor, allowing the use of MOSFET transistors with reduced intrinsic on-resistance; the input current presents small ripple; the output voltage can be further stepped up by increasing the transformer turns ratio without compromising the voltage stress across the switches; and the output voltage is naturally balanced, thus making the converter suitable for supplying split-capacitor inverters. Several topologies where a high voltage step-up is possible are initially investigated in the literature. Then, the principle of operation and experimental results for a 1-kW prototype are presented to validate the theoretical analysis and demonstrate the converter performance. [ABSTRACT FROM PUBLISHER]

The quasi-Z-source cascaded multilevel inverter (qZS-CMI) presented many advantages over conventional CMI when applied in photovoltaic (PV) power systems. For example, qZS-CMI provides the balanced dc-link voltage and voltage boost ability, saves one-third modules, etc. However, current research studies only disclosed control of single-phase qZS-CMI-based PV power systems, and there was no literature related to control of three-phase qZS-CMI-based PV power systems. In this paper, for the first time, three-phase qZS-CMI's control is proposed and demonstrated for application to PV power systems. The models of PV-panel-fed qZS H-bridge module and qZS-CMI-based PV power system are built to accurately design control algorithms for each module and the whole system. The proposed control method includes the distributed maximum power point tracking for each module, dc-link peak voltage balance control for all modules, and grid-tie control for the whole system; moreover, a new multilevel space vector modulation method is proposed for the three-phase qZS-CMI. Simulation and experimental results on a test bench with a three-phase seven-level qZS-CMI-based PV power system verify the proposed control and modulation methods. [ABSTRACT FROM PUBLISHER]

Originated from analyzing nonactive power loss, a novel optimization method and modulation solution for bidirectional isolated dual-active-bridge (DAB) dc–dc converters are proposed in order to achieve high efficiency in a wide operating range. A comprehensive nonactive power loss model is developed, including both the nonactive components delivered back to the source and from the load. This paper points out that when the minimum nonactive power loss is achieved, zero-voltage soft switching can be naturally fulfilled. The optimal phase-shift pair obtained by the proposed method can keep low values of both root mean square (RMS) current and circulating power. Rather than using ideal power flow analysis, the nonactive power loss model directly embodies practical nonideal factors, including device voltage drops. Based on the analysis, an extended dual phase shift is proposed, and different operation cases are analyzed with comparison of performance indices. Experimental tests verify the theoretical analysis and show effectiveness of the proposed approach to achieve nonactive power loss minimization and efficiency improvement. [ABSTRACT FROM PUBLISHER]

This paper presents a novel direct current-fed interleaved phase-modulated single-phase unfolding inverter for fuel-cell applications. Two active-clamped zero-voltage switching current-fed half-bridge isolated converters are interleaved in parallel input and series output configuration. Phase modulation is proposed to control these two converter cells, which generate a rectified sinusoidal pattern at the dc link. A simple H-bridge unfolding dc–ac inversion is used to produce single-phase sine voltage at line frequency switching using square-wave control. This not only simplifies the inversion stage in terms of modulation but also reduces the switching losses. Direct front-end current-fed based unfolding inverter is not reported in literature yet. Detailed analysis and design of the proposed direct current-fed single-phase unfolding inverter has been presented. Simulation waveforms using PSIM 9.0.4 are given to verify the presented analysis and design. Experimental results on a laboratory prototype rated at 200 W are demonstrated to support the investigation, to validate the accuracy of the proposed analysis and design, and to test the performance. [ABSTRACT FROM PUBLISHER]

In this paper, a high-conversion-ratio bidirectional dc–dc converter with coupled inductor is proposed. In the boost mode, two capacitors are parallel charged and series discharged by the coupled inductor. Thus, high step-up voltage gain can be achieved with an appropriate duty ratio. The voltage stress on the main switch is reduced by a passive clamp circuit. Therefore, the low resistance R{DS(ON)} of the main switch can be adopted to reduce conduction loss. In the buck mode, two capacitors are series charged and parallel discharged by the coupled inductor. The bidirectional converter can have high step-down gain. Aside from that, all of the switches achieve zero voltage-switching turn-on, and the switching loss can be improved. Due to two active clamp circuits, the energy of the leakage inductor of the coupled inductor is recycled. The efficiency can be further improved. The operating principle and the steady-state analyses of the voltage gain are discussed. Finally, a 24-V-input-voltage, 400-V-output-voltage, and 200-W-output-power prototype circuit is implemented in the laboratory to verify the performance. [ABSTRACT FROM PUBLISHER]

The pulse-train (PT) control technique for switching dc–dc converters is simple to design and benefits from excellent control performance. Up to now, almost all of the works on PT control are focused on switching dc–dc converters operating in discontinuous conduction mode, with few works reported on PT control of switching dc–dc converters operating in continuous conduction mode (CCM). In this paper, a PT-controlled CCM buck converter is studied and a unique low-frequency oscillation phenomenon is revealed, which results in large undesired inductor-current and output-voltage variations. The effect of equivalent series resistance (ESR) output-capacitor on the low-frequency oscillation is examined. The results indicate that such oscillation occurs when the ESR output-capacitor is relatively small and disappears when it is relatively large. However, a larger ESR will result in a large output-voltage ripple. In order to avoid the low-frequency oscillation and, at the same time, to ensure a small output-voltage ripple, the ICRIF circuit is applied. In this way, a small ESR output-capacitor can be used to decrease the output-voltage ripple. Simulation and experimental results are provided to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

In high current applications, paralleling three-phase voltage sourced inverters represents a modular solution for improving the system power conversion quality. Single-phase output reactors are often inserted between the output terminals of the two inverters that supply the same phase output. One function of these inductors is to limit circulating currents between the two inverters. These currents are produced by common-mode voltage differences between the three-phase output terminals of the two inverters. Since standard interleaved pulse width modulation (PWM) techniques naturally produce high-frequency common-mode voltage differences between parallel connected inverters, this paper describes a modified discontinuous PWM scheme that eliminates these voltage differences. As a result, a three-phase parallel inverter system can be operated using a single three-limb coupled inductor, significantly improving the system power conversion density as a result. An experimental 3 kW prototype system is used to compare the operation of the resultant inverter against one using separate single-phase coupled inductors. [ABSTRACT FROM PUBLISHER]

Equivalent series resistance (ESR) of output capacitor has a significant effect on the control performance of constant on-time (COT) controlled switching dc-dc converters. In this paper, a discrete-time model of COT-controlled buck converter, with variable sampling frequency, is established. Based upon which, the dynamical effects of the ESR of output capacitor on COT-controlled buck converter are revealed and analyzed. The time-domain numerical simulations of the exact switched state equations, the bifurcation diagrams, and maximal Lyapunov exponents of the discrete-time model are obtained. These results verified by experimental circuit indicate that the ESR of output capacitor is a critical factor for COT-controlled buck converter, which can eliminate the unique pulse bursting phenomenon and shift operation mode from discontinuous conduction mode to continuous conduction mode, as well as control stability. [ABSTRACT FROM PUBLISHER]

This paper is devoted to the step-up dc/dc converter family with a cascaded quasi-Z-source network (qZS-network). The cascaded (two-stage) qZS-network could be derived by the adding of one diode, one inductor, and two capacitors to the traditional quasi-Z-source inverter (qZSI). The proposed cascaded qZSI inherits all the advantages of the traditional solution (voltage boost and buck functions in a single stage, continuous input current, and improved reliability). Moreover, as compared to the conventional qZSI, the proposed solution reduces the shoot-through duty cycle by over 30% at the same voltage boost factor. Theoretical analysis of the two-stage qZSI in the shoot-through and non-shoot-through operating modes is described. The proposed and traditional qZS-networks are compared. A prototype of a step-up dc/dc converter with the cascaded qZS-network was built to verify the theoretical assumptions. The experimental results are presented and analyzed. Finally, a further optimization method of the cascaded qZS-network is proposed, and some practical design issues are discussed. [ABSTRACT FROM PUBLISHER]

In this paper, a novel Zeta-mode three-level ac direct converter is proposed. The converter realizes three-level voltage waveforms before the output filter, which can get a better harmonic spectrum and reduce the bulk of the filter. Compared with two-level ac choppers, voltage stresses of the converter can be lowered. Compared with ac–dc–ac converters with no isolation and low- or middle-frequency isolation, the converter has single power stage and bidirectional power flow. Moreover, compared with buck-mode three-level ac choppers, it can realize buck and boost output voltage. The converter has four operation states in one period of input voltage and three different operation modes in one switching period. To ensure that the converter operates reliably, the noncomplementary control strategy is presented, which can make the converter switch smoothly between different modes in bidirectional power flow. Therefore, the converter is suitable to different kinds of loads. Principle analysis and experiment results of the prototype well verify the advantages of the proposed converter. [ABSTRACT FROM PUBLISHER]

A simple current sharing control technique for the switching power supply is presented herein, whose basic concept is that the control effort created from the voltage loop is finely tuned by the control effort created from the current sharing loop based on the proposed phase link so as not only to obtain the desired output voltage but also to make the load current distributed among phases as evenly as possible. Such a control method is not only without any current sharing bus as compared with the traditional current sharing methods, but also suitable for multiple phases under the condition that any one phase among multiple phases fails. Moreover, based on phase link, there is no divider used, as compared with the traditional average current method, and hence, the number of logic elements in the field-programmable gate array (FPGA) can be reduced. In this paper, the detailed basic operating principles, together with new mathematical deductions based on the superposition concept, are firstly described, and secondly some experimental results, based on the FPGA to realize the fully digitalized control of the overall system using one-comparator counter-based sampling without any analog-to-digital converter (ADC), are provided to verify the effectiveness of proposed control strategy. [ABSTRACT FROM PUBLISHER]

In this paper, a new family of zero-voltage-transition bidirectional converters using coupled inductors is introduced. By applying two auxiliary switches and coupled inductors, soft-switching condition is achieved for all semiconductor elements regardless of the power flow direction. Moreover, the presence of coupled inductors provides significant reduction in the converter volume, since all the converter inductors are implemented on a single core. Also, all semiconductor elements benefit from soft-switching condition in full duty cycle range, and thus, high efficiency is achieved for full line voltage range. No extra voltage and current stresses on the main switches and the ease of control are the other properties of the proposed converters. The proposed bidirectional buck and boost converter is fully analyzed for both buck and boost operating modes. The validity of the theoretical analysis is justified using the experimental results of a 240-W 50–100-V prototype converter. [ABSTRACT FROM PUBLISHER]

In this paper, a novel high step-up dc–dc converter with coupled-inductor and voltage-doubler circuits is proposed. The converter achieves high step-up voltage gain with appropriate duty ratio and low voltage stress on the power switches. Also, the energy stored in the leakage inductor of the coupled inductor can be recycled to the output. The operating principles and the steady-state analyses of the proposed converter are discussed in detail. Finally, a prototype circuit of the proposed converter is implemented in the laboratory to verify the performance of the proposed converter. [ABSTRACT FROM AUTHOR]

A novel pseudo-continuous conduction mode (PCCM) boost power-factor-correction (PFC) converter and its corresponding control strategy are proposed in this paper. Connecting a power switch in parallel with the inductor makes the boost converter operate in PCCM, which provides an additional degree of control freedom to realize PFC control. Therefore, a simple and fast voltage control loop of the PCCM boost PFC converter can be designed to realize output-voltage regulation. The additional degree of control freedom introduced by inductor current freewheeling operation of the PCCM boost PFC converter has been exploited through the dead-zone control technique, which can be dynamically adjusted in accordance with the output-voltage ripple. Compared with continuous conduction mode (CCM) boost PFC converter, the controller of the proposed PCCM boost PFC converter is much simpler. Moreover, the PCCM boost PFC converter benefits with reduced inductor-current ripple and improved power factor compared with boost PFC converter operating in discontinuous conduction mode (DCM). Analysis, simulation, and a 400-W prototype of the PCCM boost PFC converter have been presented and compared with those of boost PFC converters operating in conventional CCM and DCM. The results show that the dynamic response of the PCCM boost PFC converter is significantly faster than the existing boost PFC converter. [ABSTRACT FROM AUTHOR]

This paper proposes an energy regeneration circuit for three-phase voltage-fed inverters using a modified Undeland snubber. The proposed system uses a quasi-square-wave zero voltage switching dc–dc auxiliary converter to regenerate the energy from snubber capacitor to the dc bus. The regenerative circuit uses a single active switch, and it operates independently of the three-phase inverter. Operation stages, theoretical waveforms, and a design methodology are presented. Experimental results based on a 4.5-kVA three-phase inverter prototype are included to validate the proposed topology. [ABSTRACT FROM PUBLISHER]

A simple current-sharing control technique for the switching power supply is presented herein, which is based on the concept of the differential-mode transformer and which makes the load current evenly shared well among phases all over the line voltage and load current ranges. This current-sharing structure is very simple, and it makes the efficiency relatively high at light load, which is quite suitable for industrial applications with standby power considered. In this circuit, a synchronously rectified switch is used to further upgrade the efficiency, and the coupling output inductors in copolarity are utilized to decrease the phase current ripples. In this paper, the detailed basic operating principles, together with mathematical deductions, are first described, and second, some simulated and experimental results are provided to demonstrate the proposed control strategy. [ABSTRACT FROM AUTHOR]

A high step-up conversion-ratio converter with soft switching is presented in this paper. By using both coupled inductors and isolated transformer, high voltage gain can be easily achieved without extremely high duty ratio. To deal with switching losses, the active clamping circuit is adopted to achieve the zero-voltage-switching turn-on feature for power switches and to absorb the energy stored in the leakage inductor. Moreover, the series-resonant tanks composed by leakage inductors of the transformer and resonant capacitors are used to achieve the zero-current-switching turn-off feature for rectifier diodes at the output side. Therefore, the turn-on switching loss of power switches and the reverse-recovery problem of rectifier diodes can be eliminated. The operational principles and design consideration are discussed in detail. Finally, experimental results taken from a 400-W prototype are presented to confirm the effectiveness of the proposed converter. [ABSTRACT FROM AUTHOR]

A dual resonant converter with two transformers is presented in this paper. Dual resonant tanks are composed of leakage inductors and resonant capacitors to achieve zero-current-switching turnoff for rectifier diodes at the secondary side of the transformer. Hence, the reverse-recovery problem of the rectifier diodes can be eliminated. Moreover, the active-clamp circuit does not only absorb the energy stored in the leakage inductor but also clamp the voltage stress of power switches. Compared to the conventional dual resonant converter, the zero-voltage switching operation of the proposed converter is easily achieved by using two transformers. The operation principles, design considerations, and realization are discussed in detail. Finally, experimental results from a 400-W laboratory prototype are presented to confirm the effectiveness of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper proposes a twin-buck converter with zero-voltage transition (ZVT). The converter comprises two identical buck conversion units employing power MOSFETs as the active power switches with an interleaved inductor. The ZVT is accomplished by resonating the currents between the interleaved inductor and the parasitic capacitances of the power MOSFETs. The detailed circuit operations and analysis are provided. A laboratory circuit rated at 300 W is designed and tested. Experimental results show that the switching losses can be effectively reduced by ZVT of the active power switches, accompanied by the reduced reverse recovery loss of freewheeling diodes. [ABSTRACT FROM AUTHOR]

A novel zero-voltage-transition high-efficiency bridgeless power-factor-correction (PFC) circuit with a zero-current-switching auxiliary switch was proposed, analyzed, and experimentally verified. An assist circuit, consisting of a resonant inductor, two blocking diodes, a clamping circuit, an autotransformer, and an auxiliary MOSFET switch, was used to reduce the turn-on switching loss of the two main switches of the bridgeless PFC circuit and the turn-off switching loss of the auxiliary switch. The soft commutation of the main switches is achieved without imposing an additional voltage stress on the main switches. Feedback gate-drive signals can be obtained by using an existing converter IC controller modified to fit the purpose. In this paper, a detailed description of the circuit operation will be given. Based on the analysis, the guidelines for the component selection are presented. A prototype of 100-kHz 600-W universal-line PFC bridgeless circuit was built to verify the proposed scheme. In addition, based on the same concept, a family of bridgeless PFC configuration was proposed. [ABSTRACT FROM AUTHOR]

A newly designed zero-voltage-switching (ZVS) multi-input converter is proposed in this paper. The converter can boost the different voltages of two power sources to a stable output voltage. An auxiliary circuit is employed for achieving turn-on ZVS of all switches in the proposed converter. According to various situations, the operational states of the proposed converter can be divided into two states, including a single-power-supply and a dual-power-supply state. In the dual-power-supply state, the input circuits connected in series together with the designed pulsewidth modulation can greatly reduce the conduction loss of the switches. In addition, the effectiveness of the designed circuit topology and the ZVS properties are verified by experimental results, and the goal of high-efficiency conversion can be obtained. [ABSTRACT FROM AUTHOR]

The focus of this paper is the study of direct alternating-current (ac)–ac converters, beginning by buck, half-bridge, full-bridge, and push–pull converters. From the basic converters, we apply a simple methodology to make the use of switches in commercial configurations possible. Following that, eight voltage restorers supplied either on the line side or on the load side are proposed. A comparative evaluation of these topologies concerning implementation, complexity, and component effort is presented. It is notable that some of the studied topologies are known in the literature and others are new. For one of the presented topologies, the design of a 3-kVA voltage restorer is developed, and experimental results are shown, certifying the correct operation of the drive strategy used. [ABSTRACT FROM AUTHOR]

In this paper, a robust digital voltage-mode controller (DVMC) is proposed for a fifth-order boost point-of-load converter. Salient features of the proposed topology are compared with a conventional boost converter. Mathematical models are formulated using a discrete-time modeling technique and then employed in the compensator design, which uses the digital direct design approach. The DVMC is designed to ensure load voltage regulation. Robustness theory is applied directly in the digital domain, and then, various robust stability criteria describing sensitivity functions are formulated. The controller is designed to satisfy robustness criteria and then evaluated over a range of disturbances in spite of the fact that it maintains regulation. To confirm this, design simulations have been carried out on a 25-W 12–36-V converter system. Experimental results are provided to validate the concept and also to verify the range over which the designed controller is robust. [ABSTRACT FROM AUTHOR]