Search

The circulating current of modular multilevel converter (MMC) has a great impact on the power losses, the submodule (SM) capacitor voltage ripples, and the rating of power devices. Existing analysis of circulating current has considered the capacitor voltage and the modulation signal. In this paper, the effect of semiconductor devices on the circulating current is further presented. In order to realize the different circulating current injection targets under different conditions, a unified online calculation scheme by using the instantaneous information of MMC is proposed in this paper to generate the circulating current injection references. It avoids detecting the amplitude and phase of the output current or using an extensive lookup table. Besides, a mathematical analysis model is built and it reveals the impact on the capacitor voltage ripple and the rms value of arm current with different injection references, thus guide the determination of the injection ratio. Experimental results based on a three-phase MMC prototype with six SMs per arm are presented to demonstrate the analysis of circulating current and the proposed circulating current injection references generating method is verified by different circulating current control targets with different loads. [ABSTRACT FROM AUTHOR]

Induction motor drives operated with a low ratio of the switching frequency to the fundamental frequency (i.e., pulse number) are prone to have high magnitudes of low-order torque harmonics. This paper proposes a method to analytically evaluate the harmonic torque spectrum based on the pulsewidth-modulated voltage waveforms for low pulse number operation. The predicted torque harmonic spectra for different pulsewidth-modulated waveforms are validated through simulations and experiments. This paper also reports optimal switching angles to minimize the total rms value of torque harmonics of order 6, 12, 18 $,\dots,$ $6(N-1)$ , considering the number of switching angles per quarter ($N$) to be 4 and 5. Compared to sine triangle pulsewidth modulation and selective harmonic elimination pulsewidth modulation with the same pulse number, the proposed optimal switching angles significantly reduce the total rms value of all harmonic torques of order lower than $6N$. Extensive simulation and experimental results on a 3.7-kW induction motor drive are presented to demonstrate the superior performance of the proposed optimal pulsewidth modulation. [ABSTRACT FROM AUTHOR]

This paper analyzes the performances of different carrier phase-shifting pulse width modulation (PWM) techniques to be used with a multilevel cascaded H-bridge converter in case of unbalanced operational conditions. In fact, in many practical applications, the ideal condition of equal dc voltages and equal reference signals for each H-bridge cannot be achieved. In such conditions, the conventional carrier phase-shifting PWM technique loses its harmonic canceling capabilities and then the multilevel ac voltage harmonic quality is deeply affected. To overcome this limit of the original technique, different variations have been proposed. All of them still rely on the carrier phase-shifting concept and propose to use a different value of the shifting angle for each carrier (unlike the original technique) whenever unbalanced operational conditions occur. In this paper, the three main solutions proposed over the last years to extend the capabilities of the carrier phase-shifting PWM technique are compared. The analysis is focused on a three-cell cascaded H-bridge converter. Simulation and experimental results are presented. [ABSTRACT FROM PUBLISHER]

High-frequency components of acoustic noise radiated by the electric powertrain make the subjective perception of electric vehicles worse than expected under certain operating conditions. In order to investigate the influence of acoustic components on sound quality, a pulse width modulation (PWM)-fed electric powertrain is studied in this paper. First, the acoustic noise of the electric powertrain is collected in a semianechoic chamber. Then, two types of acoustic components of the electric powertrain, namely harmonic order noise and switching noise, are distinguished through the analyses of supplied current from the inverter and gear vibration. Furthermore, the relationship between subjective perception and spectral characteristics of the noise is discussed, based on which sensitivity is established. Subsequently, the contributions of acoustic components to psychoacoustical parameters are determined. After that, a sound quality model of the acoustic noise radiated by the electric powertrain is established. The comparison between jury test and prediction shows that the established model can be used for sound quality evaluation of the electric powertrain. Finally, the influences of harmonic order noise and switching noise on subjective perception are discussed. The main original contribution of this paper concerns the influences of harmonic order noise and switching noise radiated by PWM-fed electric powertrain on sound quality. [ABSTRACT FROM PUBLISHER]

High dc voltage utilization is one of the important requirements in a three-phase inverter. Under some carrier-based pulse width modulations (PWMs), the dc voltage utilization can reach the same maximum as that under the space vector modulation. But the third harmonic component of common-mode voltage (CMV) will be increased markedly while using these carrier-based PWMs in inverters. To improve the situation, this paper proposes that a midpoint-fluctuation carrier (MFC) scheme should be used in the three-phase inverter. The MFC is formed by adding a midpoint-fluctuation signal on the standard symmetrical triangular carrier. By analyzing the linear modulation region of the midpoint-fluctuation signals, a minimum fluctuant signal in the linear modulation region is designed in the paper. Compared with the use of other conventional schemes in the three-phase inverter, the use of minimum MFC scheme has higher fundamental amplitude in the output line voltage and smaller magnitude of the third harmonic in the CMV. The feasibility and validity of the MFC are proved by experiment results in a three-phase inverter. [ABSTRACT FROM PUBLISHER]

The selective harmonic current mitigation pulsewidth modulation (SHCM-PWM) technique can be used in cascaded multilevel converters to extend the harmonic reduction spectrum, reduce the coupling inductance and increase the efficiency. The offline SHCM-PWM technique has small number of switching transitions as its switching angles can only change once in a fundamental cycle and relatively long time delays because it uses FFT. As a result, its dynamic response has a lot to desire. As it will be proven in this paper, in four-quadrant power converters, to have a good transient dynamic response, both active and reactive power must be controlled at least two times in a fundamental cycle. In this paper, a hybrid modulation technique is introduced. The proposed technique uses SHCM-PWM under steady state and phase-shift PWM (PSPWM) under transient. In addition, in order to extend the modulation index range and ensure that SHCM-PWM can process four-quadrant active and reactive power, the constraints of the switching angles for the SHCM-PWM are modified. Simulations and experiments are conducted on a seven-level cascaded H-bridge converter to verify the proposed technique. [ABSTRACT FROM PUBLISHER]

The advancement in modulation strategies brings emergent solutions to suppress the leakage current in three-phase two-level transformerless grid-connected voltage source inverters (VSIs). However, most of the techniques are analyzed based on reduced common-mode voltage pulsewidth modulation (PWM) in motor drivers but fail to satisfy the specific requirement of grid-connected applications, such as wider power factor operation and lesser current distortion. To overcome such substantial drawbacks, this paper proposes a novel scalar PWM method for transformerless grid-connected VSIs. First, presented through a generalized scalar approach with unified zero-sequence voltage generation, the method is simple to implement and favored in practice. Besides, systematic and comprehensive mathematical analysis is illustrated to exhibit the validity of implemented method in reducing leakage current and shows its advantages over whole power factor range in terms of dc-link current harmonic, output current quality, and switching losses. Finally, simulations and experimental results are carried out to verify the effectiveness and superiority of the proposed method. [ABSTRACT FROM AUTHOR]

Cascaded multicell converter (CMC) is one of the effective solutions for medium-voltage high-power drives. The inability to regenerate power back to the source is one of the limitations of this converter. The regeneration capability is obtained by using a pulsewidth-modulated active rectifier instead of a conventional three-phase passive rectifier in each cell. However, due to their two-level voltage operation at the input side, an inductor is required for each cell to filter out the switching frequency components from the input current. This paper proposes a new configuration of regenerative CMC based on coupled inductor to achieve multilevel voltage at the transformer secondary terminals. This allows us to operate the rectifier devices at reduced switching frequency. The coupled inductor reduces the total harmonic distortion (THD) of the transformer secondary current and thus the transformer size. The size of the filter inductor and the transformer ratings are compared. The operating principle and the detailed analysis are presented. A technique to bypass a faulty module is proposed. The working of the converter is verified through simulation and experimental studies. [ABSTRACT FROM AUTHOR]

In voltage-source converter (VSC) systems, utilization of filter inductors with deep saturation characteristics is often advantageous due to the improved size, cost, and efficiency. However, with the use of conventional current regulation (CCR) methods, the inductor saturation results in significant dynamic performance loss and poor steady-state current waveform quality. This paper proposes the inverse dynamic model (IDM)-based compensation method to overcome these performance issues. The method converts the nonlinear inductor of the plant to a fictitious linear inductor such that linear current regulators can perform satisfactorily. In conjunction, identification of L–R parameters is performed to obtain IDM of the system within an acceptable range of sensitivity yielding satisfactory performance. The performance issues of CCR methods with saturable inductor are demonstrated by simulations and experiments. Then, the proposed method is experimentally verified on a single-phase 1.5-kW grid-connected VSC. The performance improvement over the CCR methods is verified by a detailed comparison of experimental waveforms. [ABSTRACT FROM AUTHOR]

This paper provides robust $\mathcal {H}_{\infty }$ state feedback controllers suitable for implementation in three-phase grid-connected converters. This control strategy is known to provide optimal rejection of disturbances, but usually leads to high control gains, that may be difficult to be implemented in practice. To mitigate this problem, a linear matrix inequality condition based on slack variables is proposed, which allows to impose bounds on the control gains in a less conservative way than conventional quadratic stability. The performance is proven to be superior to similar $\mathcal {H}_{\infty }$ state feedback controllers in the literature, providing an upper bound for the converter output admittance and experimental grid currents complying with the IEEE Standard 1547. [ABSTRACT FROM AUTHOR]

In domestic induction heating applications, the modulation technique applied to the inverter has a high influence on the acoustic noise emissions. These noise emissions must be avoided, since they may be audible and annoying to the final user. This paper analyzes the acoustic noise emissions that appear when a series half-bridge resonant inverter is operated with a phase-accumulator-based modulator. This modulation technique has the advantage of operating in the frequency domain, and it is compared with the classical pulsewidth modulator regarding the audible noise generated. The frequencies of the tones in the acoustic noise spectrum are theoretically calculated from the parameters of the phase-accumulator-based modulator. The spectral flatness measure is used to quantify the number of cases in which tones are generated by the modulation. Two techniques are applied to the phase-accumulator-based modulator, and their effect is tested. Theoretical results are experimentally verified. [ABSTRACT FROM AUTHOR]

Among multilevel converter topologies, the cascaded H-bridge (CHB) converter is one suitable solution for multiple applications, such as flexible ac transmission systems and motor drives. CHB presents a natural high modularity because it is formed by the serial connection of H-bridges. This paper deals with a CHB where the cells do not have the same aging because the maintenance during the years of operation forces to replace some damaged cells of the converter with new or repaired ones. A method based on clamping one power cell can be used to reduce the power losses of that cell reducing its temperature and increasing its lifetime. However, clamping one cell of the CHB introduces high harmonic distortion around twice the carrier frequency due to the CHB unbalanced operation when a conventional phase-shifted pulsewidth modulation (PWM) is applied. A deep harmonic distortion analysis of the CHB output voltage with thermal control based on clamping one cell is presented. Using this analysis, the harmonic distortion at twice the carrier frequency is eliminated applying a nonconventional phase-shifted PWM where the angles between the carriers of consecutive power cells are modified. Experimental results show how the thermal control applying the clamping of a power cell is achieved while the harmonic distortion around twice the carrier frequency is eliminated. [ABSTRACT FROM AUTHOR]

This paper presents a five-phase dual random space vector pulsewidth modulation (FPDR-SVPWM) strategy with an optimized probability density function (PDF) for a five-phase voltage-source inverter, and its performance and evaluation are also analyzed. Based on the nearest four vectors modulation method, the FPDR-SVPWM strategy, combined with random switching frequency and random zero vector, is investigated to significantly reduce the amplitude of high-order harmonics near the switching frequency and its integer multiples. For the nonsinusoidal power supply, third harmonic injection is introduced in this modulation strategy as well. Considering the effect of random numbers on the performance, an optimized Beta distribution is studied in detail. In order to analyze harmonic dispersion degree qualitatively and quantitatively, the power spectral density and the harmonic spread factor are both employed to assess the performance of the FPDR-SVPWM strategy. A series of results of simulation in MATLAB and experiments based on field programmable gate array demonstrate that the proposed modulation strategy is correct and valid, and it distributes high-order harmonics into a wide range without affecting the fundamental wave and third harmonic. [ABSTRACT FROM AUTHOR]

Variable frequency asymmetrical pulsewidth modulation (VFAPWM) is widely used in wireless power transfer (WPT) systems to control the amount of power transferred. This control scheme is also adopted in Qi, one of the world's most well-known wireless charging standards. Conventionally, the analysis of WPT systems is based on first harmonic approximation, which only considers the fundamental harmonic signals. This could be inaccurate for variable frequency asymmetrical pulsewidth-modulated WPT systems because VFAPWM inherently produces multiple harmonics. In this paper, a new analytical technique, called multiple harmonics analysis (MHA), is developed to analyze series–series-compensated WPT systems. The MHA technique is a comprehensive design foundation and provides a set of closed-form solutions to predict quantities, such as zero-voltage switching (ZVS) and voltage gain. New phenomena in ZVS and voltage gain are discovered. The accuracy of MHA is also confirmed by both simulation and experimental measurements. [ABSTRACT FROM AUTHOR]

In this paper, a new voltage balancing strategy based on improved carrier-phase-shifted pulsewidth modulation (CPS-PWM) scheme and fundamental frequency sorting algorithm (FFSA) is proposed. FFSA is a salient method which sorts the capacitor voltages at fundamental frequency and utilizes the different charging ability of driving signals to converge the capacitor voltages. Unfortunately, under the CPS-PWM scheme with high carrier frequency, 250 Hz or higher, FFSA cannot bring the capacitor voltage to the nominal value once the unbalance occurs, because there is a little difference remaining in the driving signal's charging ability. To avoid this disadvantage, an improved CPS-PWM scheme is proposed. In this scheme, driving signals with proper phase angle differences are selected to be dealt with logic and/or processing according to the sorting result of FFSA. With the logic processing, new driving signals with obviously different charging abilities are synthesized, which are assigned to the corresponding unbalanced submodules to achieve the balance of capacitor voltages. And several regions for logic processing are set up, where the proper phase angle difference is selected for each region in order to both guarantee the convergence speed and avoid the voltage oscillations. With the proposed scheme, FFSA can be adopted under CPS-PWM with high carrier frequency. Moreover, the merits of FFSA are inherited, such as the reduced computational burden and the elimination of arm current detection. Performance and effectiveness of the proposed strategy are validated by both simulations and experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a novel single-phase multicell converter for ac–dc power conversion, which is formed by a series connection of several full-bridge converter stages through passive components. The proposed topology employs a simple control scheme based on the carrier-based sinusoidal pulsewidth modulation technique. Detailed design procedure of the passive filter components are analyzed and discussed. An efficient optimization method based on a differential evolution algorithm is utilized to optimize the filter parameters. Considering the filter structure, active damping is introduced in the control scheme to improve the stability of the overall system, which is later verified by experiments. The systematic design approach of the controller parameter is also highlighted, focusing a specific set of goals. Experimental results for a 1-kW prototype are presented to further validate the concept. [ABSTRACT FROM AUTHOR]

Multilevel inverters with dodecagonal (12-sided polygon) voltage space vector (SV) structures have advantages like extension of linear modulation range, elimination of fifth and seventh harmonics in phase voltages and currents for the full modulation range including extreme 12-step operation, reduced device voltage ratings, lesser dv/dt stresses on devices and motor phase windings resulting in lower EMI/EMC problems, and lower switching frequency—making it more suitable for high-power drive applications. This paper proposes a simple method to obtain pulsewidth modulation (PWM) timings for a dodecagonal voltage SV structure using only sampled reference voltages. In addition to this, a carrier-based method for obtaining the PWM timings for a general N-level dodecagonal structure is proposed in this paper for the first time. The algorithm outputs the triangle information and the PWM timing values which can be set as the compare values for any carrier-based hardware PWM module to obtain SV PWM like switching sequences. The proposed method eliminates the need for angle estimation, computation of modulation indices, and iterative search algorithms that are typical in multilevel dodecagonal SV systems. The proposed PWM scheme was implemented on a five-level dodecagonal SV structure. Exhaustive simulation and experimental results for steady-state and transient conditions are presented to validate the proposed method. [ABSTRACT FROM PUBLISHER]

In this paper, a real-time implementation of selective harmonic elimination pulsewidth modulation (SHEPWM) using generalized Hopfield neural network (GHNN) as applied to the single-phase inverter is designed and discussed. Finding the location of the switching instants in the case of SHEPWM involves the solution of a set of nonlinear algebraic transcendental equations. The problem is redrafted as an optimization problem, and it is solved by using GHNN. Though, in principle, the $n$ number of harmonics can be eliminated using the presented methodology, this paper tries for the case of the elimination of the 5th-, 7th-, 11th-, and 13th-order harmonics while retaining the desired fundamental. An energy function is formulated for this problem and the set of ordinary differential equations (ODEs) describing the behavior of GHNN is obtained. A program in KEIL C was developed to solve these systems of ODEs by the Runge–Kutta fourth-order method to give the switching instants for continuously varying modulation indexes $(M)$. A MATLAB simulation was carried out, and an experimental setup was also constructed in order to validate the simulated results. The fast Fourier transform analysis of the simulated output voltage waveform and the experimental output voltage waveform confirms the effectiveness of the proposed method. Hence, the proposed method proves that it is much applicable in the industrial applications by virtue of its suitability in real-time applications. [ABSTRACT FROM PUBLISHER]

In constant-voltage constant-frequency (CVCF) pulsewidth modulation (PWM) dc–ac inverters, the lumped disturbance, including the parameter uncertainties, unmodeled dynamics, and nonlinear loads, will deteriorate the performance and cause high harmonic distortions, or even result in instability. Conventional disturbance observer (CDOB), in which a low-pass $Q$ filter is adopted to estimate the lumped disturbance, cannot completely eliminate the harmonics. While the conventional repetitive control (CRC) can attenuate the harmonics by using the error signal of previous period(s), that may result in slow transient response due to nonperiodic components in the tracking error during the transient state. In this paper, an internal model-based disturbance observer (IM-DOB) is proposed and has been applied in a CVCF PWM inverter to improve the control performance. In IM-DOB, a novel IM-based disturbance estimation observer is proposed to estimate the disturbance both in the low-frequency region and at harmonic frequencies, while compensation filters are introduced to enhance the robustness and stability. The IM-DOB scheme, which fuses the merit of CDOB and CRC, is actually a two-degree-of-freedom scheme. The stability analysis and a design case are also given. Comparative experiments are conducted to demonstrate the effectiveness of the proposed scheme. [ABSTRACT FROM PUBLISHER]

Impedance network inverters are the best alternatives for voltage-source and current-source inverters. The boosting capability and the shoot-through solution of such converters make them excellent solutions for various applications. Nevertheless, hard switching forces the converter to operate in low switching frequency, which results in a bulky impedance network. Moreover, the coupling between the shoot-through duty cycle and the inverter modulation index makes a tradeoff between the voltage gain and the modulation index (output voltage harmonics). This paper presents a novel dual switching frequency modulation to mitigate the switching losses of the converter, which results in a more compact impedance network. The proposed method combines a high-frequency pulse width modulation with a low-frequency sinusoidal pulse width modulation (SPWM). Therefore, the switching losses decrease considerably with respect to the conventional simple boost modulation. In addition, the impedance network design frequency remains high, and the network size decreases obviously. The proposed approach removes the interdependence between the shoot-through duty cycle and the inverter modulation index. A comparison between the proposed method and the conventional simple boost method is performed to show its advantages over the conventional method. Finally, experimental results are presented to validate the performance of the proposed method. [ABSTRACT FROM PUBLISHER]

Interleaved converter legs are typically modulated with individual carriers per leg and phase-shifted pulse width modulation (PS-PWM) as it facilitates current balancing amongst the legs. Phase-disposition PWM (PD-PWM), despite the better harmonic performance, cannot be directly used due to the resulting current imbalance that may damage the converter. This paper addresses the current sharing issue and proposes a sorting algorithm implementation that enables single-carrier PD-PWM technique for interleaved two-level converter legs. An extension of the proposed algorithm through a switching state feedback loop, limiting the average switching frequency, is also developed. In both cases, the output current is of high quality and shared amongst the phase-legs, while the deviation between the phase-leg currents is well regulated. Simulation results demonstrate the general function of method for multiple interleaved legs as well as its current sharing capabilities for high-power applications. Experimental results from a low-power laboratory prototype validate the operation of the proposed approach. [ABSTRACT FROM PUBLISHER]

Traditional model predictive control cost functions, when utilizing long prediction horizons ( $N\geq 10$) in power inverter applications, have demonstrated harmonic performances approaching that of schemes based on offline-generated optimal pulse patterns. However, long prediction horizons often prohibitively increase computational load. A different approach to maximizing harmonic performance is taken in this paper. It is shown that shaping the output voltage spectra using a simple feedback mechanism can significantly reduce the length of the required prediction horizon, facilitating a feasible computational load. When a short-horizon cost function is augmented by the feedback mechanism an excellent tradeoff between harmonic performance and switching loss is achieved, even with a prediction horizon of one. It is also shown that the feedback mechanism can be used to improve input reference tracking. Experimental verification of the proposed modulator is performed on a two-level three-phase inverter. [ABSTRACT FROM AUTHOR]

In this paper, a new carrier-based pulse width modulation (PWM) strategy providing common-mode voltage (CMV) elimination and reduced current ripple in a three-level neutral-point-clamped inverter is introduced. The employed switching sequences are made up of the three zero CMV (ZCMV) vectors, and one among the three vec-tors is applied at two ends of a half-carrier cycle. The output current ripple characteristics pertaining to those switching sequences are investigated. In a carrier cycle, the root-mean-square current ripple minimization is analyzed and an optimal sequence is derived accordingly. The presented PWM scheme results in a considerably reduced current harmonic distortion in a wide modulation region as compared to the two existing ZCMV schemes on the same average switching frequency. Also, an implementation of sawtooth-carrier-based PWM patterns is proposed for further improvement of the harmonic performance. The algorithm requires small computational burden and is straightforward for an online implementation. Simulation and experimental results are both provided to validate the good performance of the proposed PWM method. [ABSTRACT FROM PUBLISHER]

In this paper, a method to directly shape the output impedance of an inverter is proposed to reduce the total harmonic distortion of the output voltage, based on the uncertainty and disturbance estimator (UDE)-based robust control framework. It is shown that, because of the two-degree-of-freedom feature of the UDE-based control strategy, the UDE filter directly affects the inverter output impedance. A multi-band-stop filter instead of a commonly adopted low-pass filter is then proposed to directly minimize the output impedance around the harmonics to reduce the effect of nonlinear loads and assure robustness to frequency variations. Two tradeoffs are revealed: one between filter bandwidth and stability and the other between robustness and the number of harmonics suppressed. The effectiveness of the proposed control strategy is fully supported by experimental results. [ABSTRACT FROM PUBLISHER]

Due to the inductor–capacitor (LC) filter, a pulsewidth-modulation (PWM) current-source converter may experience LC resonance. The resonance can be excited by system harmonics either from the PWM process or from the grid voltage distortions and hence results in the line current distorted. In this paper, feedback controls using different variables in the LC filter are first investigated and comprehensively analyzed. It is shown that the inductor-voltage feedback or the capacitor-voltage feedback can damp the current oscillations by increasing the damping ratio, while the inductor-current feedback or the capacitor-current feedback is able to suppress low-order harmonics by raising the resonance frequency. On this basis, a group of combined variable feedback control methods is presented by combining the feedbacks of the inductor/capacitor current and the inductor/capacitor voltage. Thus, not only the current oscillations can be damped, but also the low-order harmonics can be suppressed. Therefore, the line current waveform is improved, and the system performance can be flexibly optimized. A practical design method for feedback gains is also presented in this paper. Finally, the simulation and experimental results verify the feasibility and validity of the proposition. [ABSTRACT FROM PUBLISHER]

This paper presents the mathematical and harmonic analyses of output phase voltages of three-phase voltage source inverters which employ a hybrid two-dimensional–threedimensional (2-D–3-D) space vector modulation (SVM) voltage control algorithm. The explicit time-domain representation of the harmonic components in addition to the total harmonic distortion (THD) of the output phase voltages is given in terms of system and control parameters. This paper also investigates the harmonic characteristics and THD performance against the linearity of the modulation region which helps in the harmonic performance and design studies of such inverters employing the hybrid 2-D–3-D SVM. The fundamental component of the output voltages follows the reference with lower THD in the linear modulation region rather than the overmodulation region. Experimental results are used to validate these analyses as well as the effectiveness of the hybrid 2-D–3-D SVM algorithm for generating balanced and low THD phase voltages. [ABSTRACT FROM PUBLISHER]

The Z-source inverter (ZSI) employs an LC impedance network between the main inverter bridge and the power source. The unique feature of the ZSI is that it can operate either in buck or boost mode with a wide range of obtainable output voltages from a given input voltage. This topology also exhibits better electromagnetic-interference noise immunity when compared to a traditional voltage-source inverter (VSI). However, the LC impedance network of ZSI significantly increases the size and cost of the power converter and can make it unsuitable for low-power applications. This paper proposes a novel topology called switched boost inverter (SBI) which exhibits similar advantages of ZSI with lower number of passive components and more active components compared to ZSI. The steady-state and small-signal analyses of SBI, along with its pulsewidth modulation (PWM) control strategies, have been discussed in this paper. This paper also presents a comparison of SBI and ZSI with the same input and output parameters. The theoretical analysis given in this paper has been validated using a laboratory prototype of SBI, and the experimental results are presented for verification. The experimental harmonic spectrum of the inverter's output voltage with the proposed PWM technique is also plotted and compared with that of a traditional VSI. All the experimental results show good correlation between theory and experiments. [ABSTRACT FROM PUBLISHER]

The main objective of this paper is to examine the operation of a fundamental buck-based three-phase single-stage ac–dc full-bridge converter. In this paper, the operation of this fundamental converter is explained and analyzed, and a procedure for the design of its key components is derived and demonstrated with an example. The performance and characteristics of the converter are shown with experimental results that have been obtained from a prototype, and general concluding remarks comparing buck-based and boost-based three-phase single-stage ac–dc full-bridge converters are made. [ABSTRACT FROM PUBLISHER]

In this paper, a photovoltaic (PV) microinverter capable of operating in both island mode and grid-connected mode by means of a reconfigurable control scheme is proposed. The main advantage of control reconfiguration is that in grid-connected mode, the microinverter works as a current source in phase with the grid voltage, injecting power to the grid. This is the operation mode of most commercial grid-connected PV microinverters. The idea is to provide those microinverters with the additional functionality of working in island mode without changing their control algorithms for grid-connected mode, which were developed and refined over time. It is proposed that in island mode, the microinverter control is reconfigured to work as a voltage source using droop schemes. These schemes consist in implementing P/Q strategies in the inverters, in order to properly share the power delivered to the loads. The aim of the paper is to show that the proposed control reconfiguration is possible without dangerous transients for the microinverter or the loads. Simulation and experimental results on an 180-W PV microinverter are provided to show the feasibility of the proposed control strategy. [ABSTRACT FROM PUBLISHER]

During the design phase of a modular multilevel converter (MMC), an accurate loss evaluation of the submodule (SM) plays an important role. In this paper, a method based on the analytical description of the MMC key waveforms that allows to directly obtain the average semiconductor and capacitor losses that each SM will experience is introduced, under different operating conditions or control schemes. To verify the proposed concept, the results are compared with the losses obtained from a switched model with closed-loop control, where the analytical MMC key waveforms are approached in steady state. The proposed method provides a great flexibility and a significant reduction of the simulation/computational time otherwise needed to evaluate SM losses under various operating conditions. [ABSTRACT FROM PUBLISHER]

Multilevel cascaded H-bridge converters have become a mature technology for applications where high-power medium ac voltages are required. Normal operation of multilevel cascaded H-bridge converters assumes that all power cells have the same dc voltage, and each power cell generates the same voltage averaged over a sampling period using a conventional phase-shifted pulse width modulation (PWM) technique. However, this modulation method does not achieve good results under unbalanced operation per H-bridge in the power converter, which may happen in grid-connected applications such as photovoltaic or battery energy storage systems. In the paper, a simplified mathematical analysis of the phase-shifted PWM technique is presented. In addition, a modification of this conventional modulation method using variable shift angles between the power cells is introduced. This modification leads to the elimination of harmonic distortion of low-order harmonics due to the switching (triangular carrier frequency and its multiples) even under unbalanced operational conditions. The analysis is particularized for a three-cell cascaded H-bridge converter, and experimental results are presented to demonstrate the good performance of the proposed modulation method. [ABSTRACT FROM PUBLISHER]

This paper presents a new high-frequency modulation method for multilevel converters. The proposed method provides a broad linear operating range and can be digitally implemented with minimal computational effort. This modulation method creates a phase voltage composed of a rectangular component superimposed on the top of a quasi-square-shaped reference function. The reference functions are defined such that the utilization of the dc-link voltage is maximized in any modulation index, while the dv/dt of the switches is always the minimum possible value. In order to implement the proposed method, an update time that is much shorter than the fundamental period is defined in the algorithm for updating the rectangular components of the reference voltage. The high-frequency rectangular component can then be imposed on the reference function to generate the final switching function by switching between two voltage levels during the time between two update instances. Several experimental results are provided to evaluate the performance of the proposed method and to compare its operation to conventional methods. [ABSTRACT FROM PUBLISHER]

In this paper, the near-state pulse width modulation (NSPWM), adapted to be used in dual-voltage source inverter (VSI) fed open-end load, is introduced primarily aiming to appreciably minimize the voltage total harmonic distortion (THD). Within the framework of the proposed method, the active time of pulses at the second inverter is relatively adjusted within switching interval (compared to the first VSI). The phase voltage harmonics are formulated for dual-inverter modulated by NSPWM; then, optimal adjustment is identified via a three-dimensional curve of phase voltage THD versus modulation index (MI) and phase angle displacement (PAD). Due to the limitation of MI in NSPWM, the desired output voltage is synthesized with modifying not only MI but also PAD between references of two VSIs. Furthermore, NSPWM inherently takes advantage of better efficiency compared to conventional space vector modulation due to switching only two phases within an interval (by clamping one phase to positive/negative dc-rail). The dual-VSI supplied by two isolated dc sources is assembled in the laboratory to experimentally evaluate the THD reduction feature of the proposed method; also, the simulation results obtained by means of a MATLAB/Simulink environment show close agreement with experimental data. [ABSTRACT FROM PUBLISHER]

In grid-connected inverters, a feedforward controller accurately compensates for a large number of the harmonic components of the injected current. This controller is fast and directly tackles the grid dynamic voltage disturbances without doing any further harmonic analysis. A feedforward controller was introduced to a three-phase grid connection with a wye configuration; however, for the widespread delta connections, such a scheme is less established. Moreover, the nonsinusoidal profile of the grid voltage waveform makes the online conversion of line-to-line values into phase values impossible. In this paper, implicit zero-sequence discontinuous pulse width modulation (IZDPWM) based feedforward control is implemented on the two-level grid-connected inverter. Regardless of the grid topology, the IZDPWM-based controller ensures sinusoidal current injection to the grid under balanced, unbalanced, and distorted conditions. [ABSTRACT FROM PUBLISHER]

Multilevel active neutral-point-clamped (ANPC) converter is popularly known for its higher medium voltage drives up to 6.9 kV. However, common-mode voltages (CMV) are generated when using the well-established carrier-based pulse width modulation (PWM) modulation technique. As a result, CMV will become the major cause of the premature bearing failures and the conducted electromagnetic interferences. In this paper, a reduced CMV strategy is proposed for the ANPC which employs an alternatively new hybrid carrier-based modulation named as interleaved sawtooth carrier phase-disposition PWM (ISC-PD-PWM). By doing so, enhanced harmonic profile is achieved as compared to the typically used classical phase-shifted carrier PWM (PSC-PWM). Therefore, a comparative evaluation of the seven-level (7L) ANPC performance using the proposed reduced CMV approach is made between the novel hybrid ISC-PD-PWM and the conventional PSC-PWM in terms of harmonic analysis. The experimental results have proven the feasibility of the proposed concepts with the CMV effectively reduced. Such perceived merits make ANPC be more attractive for its motor drives. [ABSTRACT FROM AUTHOR]

In this paper, a novel active power filter (APF), which utilizes a highly reliable and efficient dual-buck inversion topology, is designed and integrated to a more electric aircraft (MEA) power grid to eliminate harmonics, correct power factor of supplies, and minimize the effect of unbalanced loads. The harmonic cancellation method, which provides a three-phase reference current in phase with the positive sequence of fundamental voltage, and the hysteretic current control method are adopted to control the proposed APF. After the parameters are carefully designed, which is swiftly followed by operational principle analysis, the proposed APF is integrated into a 125-kVA frequency-wild (360–800 Hz) hybrid high-voltage alternating current/high-voltage direct current MEA power grid. System-level simulations are carried out within the whole flight phases, with and without the proposed APF. The results show that the system harmonics and power factor can be strictly limited within the requirements of the most recent military aircraft electrical standard MIL-STD-704F with the proposed APF. [ABSTRACT FROM AUTHOR]

This paper reports on flux harmonic distortion factor and current ripple analysis for various discontinuous pulse-width-modulation (PWM) techniques, which are applicable in conjunction with five-phase two-level inverter-fed induction motors. The analysis is based on the application of the complex space vector approach. The results are compared throughout with the corresponding continuous PWM techniques. Different space vector PWM and carrier-based PWM methods are encompassed by the analysis. This paper is supported by extensive simulation results. Verification of theoretical findings is provided through experimental measurements on a five-phase induction motor. [ABSTRACT FROM AUTHOR]

Multiphase (more than three phases) power electronic converters are required mainly for feeding variable-speed multiphase drive systems. This paper presents one such solution by using a direct ac–ac converter that can be used to supply a nine-phase drive system. The input is a fixed-voltage and fixedfrequency three-phase input, and the output is a variable-voltage and variable-frequency nine-phase output. A simple pulsewidthmodulation technique is developed for the proposed ac–ac converter named as a nonsquare three-to-nine-phase matrixconverter configuration. The developed modulation technique is based on the comparison of a high-frequency carrier signal with the duty ratios. Although the carrier-based scheme is widely employed for the control of back-to-back converters, it has recently been used for controlling a three-to-three-phase matrix converter. This concept is extended in this paper for controlling a threeto-nine-phase matrix converter. With the two techniques that are proposed, one outputs 0.75 of the input magnitude and the other outputs reach 0.762 of the input. This is the maximum value of the output voltage in the linear modulation range that can be achieved in this configuration of the matrix converter. The viability of the proposed control techniques is proved analytically through simulation and an experimental approach. [ABSTRACT FROM PUBLISHER]

This paper is focused on the analysis of the acoustic noise of the magnetic origin emitted by ac electrical machine variable-speed drives. First, the principle of noise generation is presented as well as the method for taking into account the effects of the current harmonics on noise generated by the pulsewidth modulation supply. The experimental results for noise and vibrations are then presented. Afterward, the elements of the per-phase equivalent circuit for higher harmonic orders are identified. They show that usual assumptions to characterize that circuit are not applicable for high-frequency harmonics. The originality of this paper concerns the rotor design: A practical procedure to diminish the acoustic noise due to the switching is defined from the per-phase equivalent circuit. It is also shown that this design makes it possible to increase the machine efficiency. [ABSTRACT FROM PUBLISHER]

This paper presents a novel topology for a direct ac–ac power converter, called as the “three-to- k” phase matrix converter. The input to the proposed matrix converter configuration is a three-phase fixed voltage and a fixed frequency supply from the grid. The output is a variable voltage and variable frequency ac supply of any number of phases (k phase). However, the discussion is limited here for a k that is equal to odd number of phases. As an example, a “three-to-five” phase matrix converter is utilized for discussion and analysis. This paper also proposes two pulsewidth modulation (PWM) control techniques for the general topology of the “three-to- k” phase matrix converter. This is based on the so-called direct duty ratio PWM (DPWM). In one presented technique, the output voltage is limited to one half of the input voltage. For the other proposed scheme, the output voltage is enhanced to 78.86% of the input voltage. The proposed control algorithm is validated using simulation and an experimental approach. [ABSTRACT FROM AUTHOR]

Harmonics are a very important issue in the design and operation of medium-voltage inverter drives, due to restrictions imposed by regulations. This paper studies the harmonics generated by a three-phase multicell cascade inverter, with singlephase pulsewidth modulation rectifiers at the input side of each cell; thus, the entire topology is able to regenerate power to the net. This paper identifies accurately the harmonic generation process in the dc-link voltage, the input current of each cell, and, therefore, at the input side of the inverter. Moreover, this paper proposes a method to reduce and, in some cases, eliminate the input current harmonics, reaching a very high input power factor for any operation condition. Simulation and experimental results are provided to validate the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper addresses theoretical calculation of a single-phase multilevel pulsewidth modulation (PWM) inverter current total harmonic distortion (THD). Analytical approach introduced in late 1980s for a two-level inverter is generalized for an arbitrary level count for a single-phase inverter. Although the obtained closed-form piecewise analytical solutions assume (infinitely) large ratio of switching and fundamental frequencies and pure inductive load, they are practically very accurate for the ratios of (apparent) switching and fundamental frequencies larger than 25–30 and inductance-dominated loads. Along with strict mathematical solutions, simple accurate Bessel function approximation and hyperbolic average trend one are suggested. The formulas clearly reveal a single-phase PWM inverter current THD dependence on modulation index for an arbitrary voltage level count and are easily modified to cover grid-connected cases. [ABSTRACT FROM PUBLISHER]

Interleaving of voltage-source converter (VSC) legs enables higher output currents per phase, effectively increasing the power rating without increasing semiconductor ratings. However, the interleaved operation results in circulating currents between each phase converter legs as well as a zero-sequence circulating current (ZSCC), which become quite prominent when the converters operate with low switching frequencies. This paper demonstrates the interleaved operation of three-level converters under selective harmonic elimination pulsewidth modulation (SHE-PWM). A controller for the circulating current within the legs of each phase is also proposed. The controller is used in combination with optimally selected SHE-PWM patterns to generate the maximum number of voltage levels and minimize the peak value of the circulating current. Simulation and experimental results show the interleaved operation and the effect of SHE-PWM pattern selection in the overall system. [ABSTRACT FROM PUBLISHER]

The cost reduction of power-electronic devices, the increase in their reliability, efficiency, and power capability, and lower development times, together with more demanding application requirements, has driven the development of several new inverter topologies recently introduced in the industry, particularly medium-voltage converters. New more complex inverter topologies and new application fields come along with additional control challenges, such as voltage imbalances, power-quality issues, higher efficiency needs, and fault-tolerant operation, which necessarily requires the parallel development of modulation schemes. Therefore, recently, there have been significant advances in the field of modulation of dc/ac converters, which conceptually has been dominated during the last several decades almost exclusively by classic pulse-width modulation (PWM) methods. This paper aims to concentrate and discuss the latest developments on this exciting technology, to provide insight on where the state-of-the-art stands today, and analyze the trends and challenges driving its future. [ABSTRACT FROM PUBLISHER]

In this paper, a new inverter topology is proposed for generating a multilevel dodecagonal voltage space vector structure for open-end winding induction motor (IM) using a single dc source. Dodecagonal voltage space vector structure eliminates fifth- and seventh-order harmonic voltages from phase voltage output and hence eliminates the fifth- and seventh-order harmonic currents through the motor leading to removal of the dominant sixth-order torque ripple generation in the motor over the entire modulation range. Multilevel space vector structure generates output voltage with better THD and low dv/dt. In the proposed topology, two three-level inverters drive an open-end winding IM, one inverter from each side. DC-link of primary inverter is from a dc source which delivers the entire active power, whereas the secondary inverter dc-link is maintained by a capacitor, which is self balanced during the inverter operation. The PWM scheme implemented ensures low switching frequency for primary inverter. Secondary inverter operates at a small dc-link voltage. Hence, switching losses are small for both primary and secondary inverters. Experimental results show the elimination of fifth- and seventh-order harmonic voltages over the entire modulation range, validating effectiveness of the proposed multilevel inverter scheme. [ABSTRACT FROM PUBLISHER]

In an electric drive vehicle (EDV), the available voltage on a dc-link is limited, and so the inverter output voltage and, consequently, the line motor maximum speed are limited. The fundamental voltage of the inverter output is increased approximately 27% using a square wave (SW) switching pattern instead of a sine wave switching pattern. However, this pattern can only be used at high speeds, and at lower speeds a pulsewidth modulation (PWM) pattern should be used. In order to achieve proper control, the switching pattern should be changed seamlessly. In the present paper, a new PWM scheme for single-mode seamless control of Vernier motors is proposed. In the proposed scheme, the reference voltage is modified to change the switching pattern continuously so that the voltage changes smoothly from a high-frequency pattern to an SW and voltage discontinuity does not occur. Experimental results reveal that the inverter-switching pattern changes smoothly from a sinusoidal PWM pattern to an SW pattern, and so seamless control from the constant-torque region to the constant-power region, and vice versa, is achieved. Since the proposed scheme is a single-mode control, it is much simpler than current technologies, which are based on multimode controllers. Also the proposed method has a lower total harmonic disturbance (THD) as well as a lower harmonic distortion factor (HDF) compared to some existing methods. [ABSTRACT FROM PUBLISHER]

Multilevel inverters are gaining more attention in ac drive application due to their many attractive features. In the case of conventional neutral-point-clamped (NPC) or flying capacitor multilevel inverter configurations, active switches are connected in series to produce multilevel output voltage waveform. Therefore, if any one switch fails, the entire configuration has to be shut down; this will reduce the reliability of the system. A dual three-level inverter configuration for induction motor drive is proposed in this paper to improve reliability of the system. This topology is developed by feeding four-pole induction motor stator winding with four conventional two-level inverter modules. A level-shifted carrier-based third harmonic injection pulsewidth-modulation technique is used to produce the gating signals for the proposed configuration. By providing proper phase shift between carrier waves, multilevel voltage waveform is produced across the total motor phase winding, and first center band harmonics are also canceled. Thereby, the torque ripple will be considerably reduced compared with conventional NPC five-level inverter-driven induction motor drive. Finite-element analysis (FEA) is used to estimate the torque ripple when induction motor is supplied by the proposed configuration and conventional five-level NPC inverter configuration to show the effectiveness of the proposed converter. The proposed configuration is simulated using MATLAB/Simulink and experimentally verified using a laboratory prototype with a 5-hp four-pole induction motor drive. [ABSTRACT FROM PUBLISHER]

This paper investigates possible reduction of pulsating torque in open-loop and vector-controlled induction motor drives through deployment of certain advanced bus-clamping pulsewidth modulation (ABCPWM) method. Toward this goal, a simple and machine-independent method is proposed to analyze the torque harmonic spectrum of a voltage source inverter fed induction motor, operated with any real-time pulsewidth modulation (PWM) method. The analytically evaluated torque harmonic spectra, pertaining to conventional space vector PWM (CSVPWM), bus-clamping PWM (BCPWM), and ABCPWM, are validated through simulation and experimental results. Theoretical and experimental studies bring out the superiority of the ABCPWM in terms of torque harmonics over CSVPWM and BCPWM. The magnitude of the dominant torque harmonic with the ABCPWM scheme is shown to be significantly lower than that with CSVPWM, over a wide range of speed. The rms torque ripple (i.e., total rms value of all harmonic torques) is lower with ABCPWM than with BCPWM over the entire range of speed. [ABSTRACT FROM PUBLISHER]

The most recent literature on multiphase machine drives is based on voltage-source converter (VSC) systems utilizing different modulation techniques. Very little attention is given to the multiphase current-source converters (CSCs). Applying CSCs in high-power multiphase drive systems is promising and can effectively solve many technical problems associated with conventional VSC-based systems. This paper proposes a space vector pulsewidth-modulation (SVPWM) scheme suitable for a five-phase CSC. Generally, in SVPWM-CSCs, a current path should be provided for the dc-link current by ensuring that one pair of upper and lower switches is always on. Applying this constraint yields 25 different space vectors, which are mapped into two concentric decagons with ten equal sectors in the $\alpha\beta$ and $xy$ sequence planes. Each sector has two active-large vectors, two active-small vectors, and a null vector. Moreover, the active-large vectors in the $\alpha\beta$ plane are active-small vectors in the $xy$ plane, and vice versa. In the proposed scheme, the ampere-second concept is utilized to determine the ratio between the dwelling times of the large and small vectors such that the $xy$ current components are nullified, the utilization of the input dc-current is maximized, and the switching transitions are minimized, which, in turn, minimizes the CSC switching losses. The proposed scheme can effectively provide sinusoidal converter currents, which is suitable for motor drives and energy conversion applications. The proposed scheme is verified using a 1-kW prototype five-phase induction motor fed by a five-phase CSC. [ABSTRACT FROM PUBLISHER]

In this paper, three overmodulation techniques for the three-to-five-phase indirect matrix converter (IMC) are proposed. The first technique utilizes only the adjacent large vectors in the sector in which the reference output voltage vector lies. The second technique improves on that by continuously adapting vector elimination in the d_2-q_2 vector space based on the output voltage requirements. The third technique utilizes the ripple in the dc link to further reduce the modulation index of the inverter stage during overmodulation. All three techniques increase the voltage transfer ratio of the three-to-five-phase IMC from 0.788 to 0.923, but with the addition of harmonics generated by a vector in the d_2-q_2 vector space of the inverter stage. Simulation and experimental results from a prototype three-to-five-phase IMC validate the three proposed overmodulation techniques. [ABSTRACT FROM AUTHOR]