Search

This paper presents a single-stage nonisolated switched capacitor ac–dc converter for power-factor correction (PFC). This converter features reduced passive components, single switch, transformerless high voltage gain, and improves the power factor, reduces total harmonic distortion, and voltage stress across the switch. The peak current mode with a dynamic resonant perturbation scheme compensates the subharmonics that exist at zero crossing of the source current is implemented for PFC. In this paper, the principle of operation, large signal modeling of the circuit, and control method for the proposed PFC converter are provided. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel single-switch dc/dc converter for the future renewable electric energy delivery and management system to implement the distributed renewable energy resources (DRER). The DRER is responsible for the maximum power point tracking of the photovoltaic panel (PV) module and also for the control of central energy storage device. Due to the characteristics of the PV module and the dc-bus, the single power stage must provide low current ripple in the input and output terminals, must operate with output current and voltage regulation, and present a high-voltage conversion ratio. To achieve such features, this paper proposes a novel integrated Boost–Zeta converter. To avoid a complex modeling and control, we propose a disaggregation concept for this. Experimental results are presented for the purpose of operating the converter and also for the operation of the system. [ABSTRACT FROM PUBLISHER]

This paper proposes a multilevel flying capacitor dc/dc boost converter (FCBC) with a small capacitance of the flying capacitor for the reduction of converter size. In this paper, the design methods for the boost inductor and the flying capacitor in the n-level FCBC are principally and experimentally confirmed. Furthermore, the boost inductor is designed based on maximum product of voltage-time, regardless the number of level. Meanwhile, the minimum capacitance of the flying capacitor is designed based on the maximum switching device voltage stress, regardless of the output voltage ripple influences. Moreover, the achieved maximum efficiency of the designed three-level FCBC is 98.5% at the output power of 1 kW. Finally, the effectiveness of small capacitances of the flying capacitor in the three-level and five-level FCBCs is analyzed. The characteristics of the distorted voltage across the input voltage source and the boost inductor, and the distorted current to the output side (output capacitor and load) are investigated with several capacitances of the flying capacitors in the three-level and five-level FCBCs. As a result, it is experimentally confirmed that the distorted voltage is drastically reduced by increasing the number of level. Besides, the distorted current is almost the same although the number of level is increased. Therefore, based on the experimental results, it is shown that small capacitance of the flying capacitor can be used in the n-level FCBC without compromising the stability of converter operation. [ABSTRACT FROM PUBLISHER]

A dual active bridge (DAB) converter promises high power density. The highest power transfer can be achieved by phase shift modulation inside the zero-voltage switching boundaries. This paper analyzes the transients of DAB commutation. Although commutation has been previously analyzed for DAB with the linear turn-off snubbers, in today's industries, the output capacitors of the switches are utilized as the snubberless approach. The presence of these time-variant capacitors leads to nonlinear equations. This paper applies a piecewise linear model for analyzing the commutation of the ac-link current into the switches. The study is inspired by practical experiments, and the results are experimentally verified. [ABSTRACT FROM PUBLISHER]

In this paper, a hybrid bidirectional dc–dc converter is presented, which is a combination of a switched-capacitor converter and an inductor-based converter with low component counts. The input current ripple and peak charging current are small with the help of the inductor. The proposed converter is applicable in the battery charge/discharge systems, such as the distributed renewable energy systems, battery equalizer, auxiliary power supplies, traction drive system, and dual-voltage automotive systems based in new electrical architecture concept, where common ground is not required and within the voltage-gain range of 2–6. A comprehensive analysis of the steady-state operation, small-signal model, and component stress is given. The comparison with an alternative topology shows the advantages of low component counts, low total capacitor voltage stress, low inductor current, and low total active switch stress for the 42/14 V voltage level. A 42/14 V prototype rated at 20–120 W with a peak efficiency of 97.8% in boost mode and 97.62% in buck mode was built to verify the analysis. [ABSTRACT FROM AUTHOR]

This paper presents a single-stage light-emitting diode (LED) driver based on a bridgeless power factor correction (PFC) converter and a half-bridge CLCL resonant converter for street lighting applications. The proposed single-stage topology integrates the PFC converter and the CLCL resonant converter by sharing active power switches. The bridgeless PFC converter adopts two buck–boost circuits operating in discontinuous-conduction mode to achieve input-current shaping. It uses two diodes instead of a rectifier bridge to reduce the power loss caused by the diodes. Owing to its superior soft-switching characteristics, the CLCL resonant converter is used. The proposed LED driver has superior features, such as high efficiency, near unity power factor, low total harmonic distortion, and relatively few diodes. A 100-W lab prototype is successfully implemented, and the experimental results verify the effectiveness and feasibility of the proposed LED driver. [ABSTRACT FROM AUTHOR]

This paper presents a dc/dc buck–boost converter topology with high-voltage gain and dual outputs. Unlike many of the high step-down/step-up dc/dc converters, this topology uses a relatively ower number of LC components and three active semiconductor devices switched in a nonoverlapping way. Due to the duty cycle limitation, high gain (typically more than 4) is very difficult to achieve in a single-stage regular buck–boost dc/dc converter. In the proposed converter, the overall gains at both the output ports are nonlinear functions of duty-cycles of the power devices, which help achieve an overall step-down/step-up gain of 10–15. An experimental prototype converting 48 V dc to ±5 V dc at 100 W with closed loop control is developed in order to verify the operation and effectiveness of the proposed converter structure. An output voltage ripple of ±1% and a conversion efficiency of 94% are achieved according to the experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, a robust voltage control is designed for a floating interleaved boost converter with high voltage gain. The proposed controller has an inner loop based on super-twisting sliding mode algorithm, which has continuous control signal and the sliding surface is defined for the inductor current. The reference current value is generated by active disturbance rejection control (ADRC) algorithm in the outer loop, based on the output voltage error. The stability of the sliding mode inner loop and the ADRC outer loop are proven using Lyapunov stability theorem and Routh–Hurwitz criteria, respectively. The robustness of the proposed controller is analyzed in depth, and validated by the simulations and experimental results obtained with a 100 W prototype converter. [ABSTRACT FROM PUBLISHER]

For the high-voltage direct-current (HVDC) power transmission system of offshore wind power, dc/dc converters are the potential solution to collect the power generated by off-shore wind farms to HVDC terminals. The converters operate with high-voltage gain, high efficiency, and fault tolerance over a wide range of operating conditions. In this paper, an isolated ultrahigh step-up dc/dc converter with a scalable modular structure is proposed for HVDC offshore wind power collection. A flyback-forward converter is employed as the power cell to form the expandable electrically isolated modular dc/dc converter. The duty ratio and phase-shift angle control are also developed for the proposed converter. Fault-tolerant characteristics of the converter are illustrated through the redundancy operation and fault-ride-through tests. Redundancy operation is designed to maintain high operation efficiency of the converters and fault-ride-through operation improves the converter reliability under harsh operating conditions. Analytical studies are carried out, and a 750-W prototype with three modular cells is built and experimentally tested to verify the performance of the proposed modular dc/dc converter. [ABSTRACT FROM AUTHOR]

In this paper for power factor correction (PFC), a modified Landsman converter is introduced. The application is targeted for high-brightness (HB) projection application with brightness control for HB red–green–blue (HB-RGB) light-emitting diode (LED). A pulse-width modulation (PWM) technique is used for intensity control to achieve brightness control of the LED driver. The proposed PFC converter is used to feed a dual output flyback dc–dc converter that supplies power to the forced cooling unit and the LED module with galvanic isolation. The brightness control of LED is performed by synchronous buck converter. The modified Landsman converter operates in discontinuous output inductor current mode for PFC at universal ac mains. A prototype of the proposed LED driver is experimentally verified. The performance of proposed driver is evaluated at full and light-load condition for universal ac mains (90–265 V) over a full range of brightness. The power quality parameters are found within the acceptable limits of harmonic standard IEC 61000-3-2 for universal ac mains. [ABSTRACT FROM PUBLISHER]

In order to solve the problems caused by the pulsating current ripple of switching-mode power converters, a passive pulsating ripple canceling circuit (PPRCC) is proposed in this paper. The features of the proposed PPRCC include simple, modular structure, and high degree of design flexibility. By integrating the proposed PPRCC, an input current ripple-free flyback-type converter is adopted and analyzed as an example because of its comprehensive utilization in small power rating commercial products. In addition, the switch voltage spike of flyback converter can be suppressed by integrating the proposed PPRCC without using snubbers, it turns out that the efficiency can be further improved. The corresponding operating principle, steady-state analysis, and zero ripple design criteria of the proposed PPRCC are provided. Finally, a 100 W laboratory prototype is constructed to verify the effectiveness of the proposed principle. Experimental results show that the resulting peak-to-peak input current ripple is reduced by 96% and nearly 0.5% and 1.7% improvement in efficiency can be achieved by the proposed PPRCC, at 80 W and 100 W load conditions, respectively. [ABSTRACT FROM PUBLISHER]

In LLC-based onboard battery charging architectures used in plug-in electric vehicles (PEV), the dc link voltage can be actively regulated to follow the battery pack voltage so that the LLC converter can operate in proximity of resonant frequency and achieve high efficiencies over the wide range of battery pack voltage. However, conventional boost-type power factor correction (PFC) converters are unable to provide ultrawide dc link voltages since their output voltages should always be larger than their input voltages. This paper proposes a Silicon Carbide (SiC)-based onboard PEV charger using single-ended primary-inductor converter (SEPIC) PFC converter followed by an isolated LLC resonant converter. With the proposed charger architecture, the SEPIC PFC converter is able to provide an ultrawide range for dc link voltage, and consequently enhance the efficiency of the LLC stage by ensuring operation in proximity of resonant frequency. A 1-kW SiC-based prototype is designed to validate the proposed idea. The experimental result shows that the SEPIC PFC converter achieves unity power factor, 2.72% total harmonic distortion, and 95.3% peak conversion efficiency. The LLC converter achieves 97.1% peak efficiency and always demonstrates a very high efficiency across the ultrawide dc-link voltage range. The overall efficiency of the charger is 88.5% to 93.5% from 20% of the rated load to full load. [ABSTRACT FROM AUTHOR]

In this paper, the switching cell concept is extended to isolated ac–ac converters, and a highly reliable double step-down ac–ac converter is proposed with high-frequency transformer (HFT) isolation. By using the switching cell structure and coupled inductors, the proposed converter has no commutation problem as it is immune from both short-circuit and open-circuit problems, even when all the switches are turned on or turned off, simultaneously. Therefore, it does not require pulse width modulation dead times along with bulky and lossy RC snubbers or voltage-sensing circuitry to implement soft-commutation strategies, resulting in high reliability and high quality output waveforms. The HFT in the proposed converter provides electrical isolation and safety which is required in applications such as dynamic voltage restorer (DVR), solid-state transformer (SST), etc., without the need for external bulky line frequency transformer. Moreover, all the passive components experience twice the switching frequency; therefore, their size can be reduced. The proposed converter is very suitable for application as DVR, to compensate both voltage sags and swells, owing to its ability to provide both inverting and noninverting outputs. A detailed theoretical analysis and operation of the proposed ac–ac converter are provided, and its applications as DVR and SST are also discussed. Experimental results with scaled-down prototype are also provided to verify its performance. [ABSTRACT FROM AUTHOR]

Resistance emulation using one cycle control (OCC) has been used extensively in single-phase full-bridge boost rectifiers. This paper proposes a new control strategy called dual comparison OCC (DC-OCC), which eliminates the limitations of OCC. The advantages of the proposed control strategy is that it ensures the average current is equal to grid voltage scaled by emulated resistance, in each switching cycle. This eliminates issues such as dc offset due to the peak current comparison in OCC. It also ensures that there is no distortion in current when the converter is lightly loaded. It is analytically shown that the proposed DC-OCC does not have the light load instability concerns of conventional OCC. The proposed method is also shown to achieve unipolar pulse-width modulation without sensing the grid voltage resulting in lower effective switching frequency. The proposed control requires only one additional comparator and additional logical elements for implementation. Detailed simulation and experimental studies are carried to validate the proposed control and the high performance that can be obtained. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel 3 $\phi$ stand-alone solar photovoltaic (PV) system configuration that uses high-gain high-efficiency $(\approx\! 96\%)$ dc–dc converters both in the forward power stage and the bidirectional battery interface. The high-voltage-gain converters enable the use of low-voltage PV and battery sources. This results in minimization of partial shading and parasitic capacitance effects on the PV source. Series connection of a large number of battery modules is obviated, preventing the overcharging and deep discharging issues that reduce the battery life. In addition, the proposed configuration facilitates “required power tracking (RPT)” of the PV source as per the load requirements, eliminating the use of expensive and “difficult to manage” dump loads. High-performance inverter operation is achieved through $abc$ to $dq$ reference frame transformation, which helps in generating precise information about the load's active power component for RPT, regulation of ac output voltage, and minimization of control complexity. Inverter output voltage is regulated by controlling the modulation index of sinusoidal pulsewidth modulation, resulting in a stable and reliable system operation. The active power demand is controlled by regulating the dc link voltage. All the analytical, simulation, and experimental results of this work are presented. [ABSTRACT FROM PUBLISHER]

In this paper, a passive ripple canceling circuit (PRCC) is proposed to eliminate the output power reduction effect of photovoltaic (PV) systems caused by the current ripple of the PV converters. Special features of the proposed PRCC include having low-cost simple modular structure and being independent of the duty ratio control of the main power circuit. Hence, it can be easily integrated to the main power circuit to achieve zero input current ripple, yielding less filter size, loss, and fast response. Meanwhile, the linear line maximum power point tracking (MPPT) control is also integrated with the proposed module integrated converter (MIC) to achieve instantaneous tracking response. Finally, a 90-W laboratory prototype is constructed to verify the effectiveness of the proposed principle. It is seen that the resulting peak-to-peak input current ripple is reduced to about 2% of the original dc converter input ripple. In other words, the input current ripple is almost zero. As a result, the harvested power of the proposed MIC can be increased by 7% as compared with that of the MIC without the proposed PRCC. [ABSTRACT FROM AUTHOR]