Search

Unipolar-pulsewidth modulation (UP-PWM) inverter takes advantages of high power efficiency and small output chokes which is widely used in the industry. However, UP-PWM inverters cannot be used in parallel operation due to a current unbalance problem. This paper studies the current unbalance problem of paralleled UP-PWM inverters with common dc bus and ac bus. First, the problem of unbalanced inductor current is defined and analyzed. Second, a technique to eliminate unbalanced currents is proposed. The proposed current balancing technique only requires one more current sensor in an inverter module rather than changing converter topology or modulation method, which makes it possible to apply UP-PWM inverters in parallel-operation while keeping the advantages of unipolar switching. The proposed current balancing method is verified by both simulation and hardware experiment. Experimental verification is performed on two 1 kW, 400 V input, and 120 V/60 Hz output prototypes, which shows a good agreement to the analytical study. [ABSTRACT FROM AUTHOR]

Parallel interleaved two-level (2L) three-phase voltage source inverters (VSIs) are widely used due to their distinct advantages of high power delivery, modularity, low current rating devices, etc. Along with these advantages, the parallel interleaved 2L VSIs could also be analyzed as a single three-level (3L) VSI. Conventionally parallel interleaved 2L VSIs are modulated using the 2L pulsewidth modulation (PWM) techniques. However, implementation of parallel interleaved 2L VSIs using the 2L PWM techniques may generate a higher ac side current ripple as compared to implementing the parallel interleaved 2L VSIs using 3L PWM techniques. This paper proposes a carrier-based method for implementing different 3L discontinuous PWM (DPWM) techniques for parallel interleaved 2L three-phase VSIs. Comparison of different 2L switching sequences for implementing a 3L DPWM switching sequence based on circulating current, line current ripple, and switching loss is also carried out. Simulation and experimental results are also displayed to validate the proposal. [ABSTRACT FROM AUTHOR]

This paper introduces a three-phase grid-connected inverter for commercial-scale photovoltaic systems. The circuit topology combines an ac-inductor-less active bridge with a parallel-connected pulsewidth modulation inverter acting as an instantaneous reactive power compensator. The active bridge, called a 120° conduction inverter, operates at a switching frequency equal to the grid frequency and outputs a 120° rectangular current, while the compensator eliminates the harmonic currents included in the rectangular current. The main advantage of this strategy is the reduction in size of the required ac inductor by a factor of 4, as well as the reduction of power losses in the switching devices. The theoretical analysis clearly shows that the compensator can synthesize a sinusoidal output current by controlling only instantaneous reactive power, thus eliminating the need for electrolytic capacitors. A 5-kW experimental setup validates the operating principle and the control method of the proposed inverter and exhibits an inverter efficiency as high as 99.2% with Si superjunction mosfets. [ABSTRACT FROM AUTHOR]

A switching-capacitor-based buck–boost converter (with common ground) for point of load applications is proposed in this paper. It is capable of operating in stand-alone buck or boost mode in addition to its primary operation of performing the buck–boost conversion. The striking feature of the proposed converter is low source current ripple content irrespective of its mode of operation (buck–boost, buck, or boost). First, feasible pulsewidth modulation schemes for the proposed converter are identified and thereafter the corresponding circuit performance analysis, steady-state analysis, and state-space modelling is established. Through steady-state analysis, voltage gain expressions are formulated and equations defining L-C components are derived in terms of their ripple quantities. The state-space models are used to formulate small-signal analysis and to obtain the relevant transfer functions required in the controller design. A voltage-mode/current-mode controller is designed, with a tradeoff in bandwidth, to control the proposed converter and transit it from buck to boost mode or vice versa seamlessly. A 30–55 W, 100 kHz, prototype point of load converter with 36-V input dc source is built to supply power at constant load voltage of either 48 or 28 V. The proposed converters’ effectiveness is demonstrated experimentally in terms of reduced source current ripple along with seamless transition from buck to boost mode and vice versa. [ABSTRACT FROM AUTHOR]

This paper investigates a multilevel inverter composed of series/parallel-connected H-bridges. The presented structure can be used for applications in which the use of semiconductor switches with low-voltage and low-current ratings is intended. A comprehensive system model, an overall control strategy to adjust the output voltage with constant magnitude and frequency, and a level-shifted PWM (LS-PWM) strategy based on a voltage vectors unidimensional analysis and a plane analysis are presented. The LS-PWM is capable of mitigating the low-frequency circulating current, thus generating multilevel voltage signals with low harmonic distortion, maximum number of levels, and low dv/dt. In addition, considering a wide range of values of voltages and currents and various power levels, the total converter losses are reduced compared with the conventional multilevel converters. Two multilevel conventional inverters with the same number of semiconductor switches are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

Paralleled inverters are not only a suitable approach to increase the power capacity, but also have the capability of common mode voltage (CMV) reduction, or even elimination. The original zero CMV modulation scheme for paralleled inverters suffers from the current jump problem in phase-leg currents. This current jump phenomenon amplifies the peak values of differential-mode circulating current (DMCC) and zero-sequence circulating current (ZSCC), which is adverse for the design of coupled inductor and common-mode inductor. This paper introduces the modified modulation scheme, which can keep volt-seconds balance in whole fundamental period and mitigate the current jump in phase-leg currents. In addition, the reduction effect of the DMCC and ZSCC can be achieved. To verify the analysis, both the simulation and experimental results are presented, which validates the proposed methods and show that they are beneficial for DMCC and ZSCC reduction. [ABSTRACT FROM AUTHOR]

Paralleling power converters is a common practice in industries to enhance total power rating, reliability, and availability of the system. In case of fault occurring in systems with parallel converters, the faulty power converter can be isolated and the system can still be operated at reduced power level. In this paper, a grid-connected power converter consisting of two parallel H-bridge converters with low ground leakage current is considered. Two contingency configurations, that are also of low ground leakage current, are proposed to enhance the availability of the system. This is done by reconfiguring the power circuit to a single H-bridge in the case of failure in one of the bridges. The power converter is experimentally tested with the proposed configurations for experimental validation. The results show that the second configuration has better performance in terms of power loss and current total harmonic distortion when operating at lower power level. [ABSTRACT FROM AUTHOR]

In this paper for power factor correction (PFC), a modified Landsman converter is introduced. The application is targeted for high-brightness (HB) projection application with brightness control for HB red–green–blue (HB-RGB) light-emitting diode (LED). A pulse-width modulation (PWM) technique is used for intensity control to achieve brightness control of the LED driver. The proposed PFC converter is used to feed a dual output flyback dc–dc converter that supplies power to the forced cooling unit and the LED module with galvanic isolation. The brightness control of LED is performed by synchronous buck converter. The modified Landsman converter operates in discontinuous output inductor current mode for PFC at universal ac mains. A prototype of the proposed LED driver is experimentally verified. The performance of proposed driver is evaluated at full and light-load condition for universal ac mains (90–265 V) over a full range of brightness. The power quality parameters are found within the acceptable limits of harmonic standard IEC 61000-3-2 for universal ac mains. [ABSTRACT FROM PUBLISHER]

In this paper, the switching cell concept is extended to isolated ac–ac converters, and a highly reliable double step-down ac–ac converter is proposed with high-frequency transformer (HFT) isolation. By using the switching cell structure and coupled inductors, the proposed converter has no commutation problem as it is immune from both short-circuit and open-circuit problems, even when all the switches are turned on or turned off, simultaneously. Therefore, it does not require pulse width modulation dead times along with bulky and lossy RC snubbers or voltage-sensing circuitry to implement soft-commutation strategies, resulting in high reliability and high quality output waveforms. The HFT in the proposed converter provides electrical isolation and safety which is required in applications such as dynamic voltage restorer (DVR), solid-state transformer (SST), etc., without the need for external bulky line frequency transformer. Moreover, all the passive components experience twice the switching frequency; therefore, their size can be reduced. The proposed converter is very suitable for application as DVR, to compensate both voltage sags and swells, owing to its ability to provide both inverting and noninverting outputs. A detailed theoretical analysis and operation of the proposed ac–ac converter are provided, and its applications as DVR and SST are also discussed. Experimental results with scaled-down prototype are also provided to verify its performance. [ABSTRACT FROM AUTHOR]

This paper identifies the characteristics of a current source inverter operating in discontinuous conduction mode, and proposes a new multiobjective pulse-width modulation (PWM) method to mitigate voltage boosting and harmonic distortion effects. The method takes into account load impedance effects. Controls are also developed to enable transition between the multiobjective PWM method and conventional PWM as the current source inverter operates in discontinuous and continuous modes of operation. The concept is verified experimentally on a 3 kW test bed. [ABSTRACT FROM AUTHOR]

This paper presents an energy-recycling class-D low-side gate driver integrated circuit (IC), which can also perform 5-to-15-V level upconversion using a bidirectional flyback converter topology. The gate driver itself is a mini switching regulator that operates at 5–15 MHz to generate 1-μs transition time gate-switching waveforms. In order to maintain uniform charging/discharging currents during transitions, the embedded flyback converter operates in a pulse-frequency modulation mode while charging and in a pulse width modulation mode while discharging the gate node. The required pulses with digitally programmable frequencies and duty cycles are efficiently generated by a custom-designed IC fabricated in a 0.25-μm HV CMOS technology. Also, the presented analysis guides a way to achieve the desired transition time with the maximum efficiency. The prototype IC demonstrates 37.5% energy recycling while driving a 15-V insulated-gate bipolar transistor power switch with 105-nC gate charge at 20 kHz. [ABSTRACT FROM PUBLISHER]

Although the operation of a three-phase current source rectifier (CSR) for ac-to-dc conversion using phase control or low-frequency pulse control is well established in a wide variety of applications, CSR realization using high-frequency pulsewidth-modulation control has been recently studied as a potentially competitive alternative to a voltage source rectifier. In the CSR, reverse blocking gate turn-off switches are realized using series-connected diodes, which prevent any reversal of the dc-link current. A significant consequence of this limitation occurs at light load conditions. The dc-link inductor current enters the discontinuous mode of operation and leads to the loss of the control of the output voltage and a highly distorted input current, which compromise the potential advantages of the approach. This paper characterizes the CSR while operating in the discontinuous conduction mode and proposes a modulation strategy that restores the control of the output voltage and ensures a nearly sinusoidal current at light loads. Simulation and hardware results are provided for a 3-kW laboratory-scale prototype system. [ABSTRACT FROM AUTHOR]

In this paper, analysis of circulating currents of paralleled single-phase boost converter systems is presented. The dc loop and ac loop circulating currents are clearly explained. In order to eliminate the dc loop circulating currents and reduce switching losses, a simplified pulsewidth modulation strategy is adopted in a paralleled single-phase boost converter. Based on the analysis of circulating currents, common-mode circulating current (CMCC) and differential-mode circulating current (DMCC) are defined. Then, CMCC and DMCC compensators are proposed in a centralized control scheme to reduce the common-mode and differential-mode circulating currents in a parallel system operated in both rectifier and inverter modes with different power sharing for microgrid applications. Converter-paralleled system stability analysis is also presented. Finally, a prototype system is constructed to facilitate the theoretical results as verification. From the experimental results, the proposed control scheme can indeed reduce the circulating currents under equal and/or different power rating conditions in the parallel system. [ABSTRACT FROM PUBLISHER]

This paper proposes a zero-voltage-transition (ZVT) pulsewidth-modulated (PWM) synchronous buck converter, which is designed to operate at low voltage and high efficiency typically required for portable systems. A new passive auxiliary circuit that allows the main switch to operate with zero-voltage switching has been incorporated in the conventional PWM synchronous buck converter. The operation principles and detailed steady-state analysis of the ZVT PWM synchronous converter with a passive auxiliary circuit are presented. All of the semiconductor devices aside from the main switch operate under soft-switching conditions. Thus, the auxiliary circuit provides a larger overall efficiency. The feasibility of the auxiliary circuit is confirmed by the simulation and experimental results. [ABSTRACT FROM PUBLISHER]